Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “difficult”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Incineration as a Method for Resource Recovery from Inedible Biomass in a Controlled Ecological Life Support System

Resource recovery from waste streams in a space habitat is essential to minimize the resupply burden and achieve self-sufficiency. In a Controlled Ecological Life Support System (CELSS) human wastes and inedible biomass will represent significant sources of secondary raw materials necessary for support of crop plant production (carbon, water, and inorganic plant nutrients). Incineration, pyrolysis, and water extraction have been investigated as candidate processes for recovery of these important resources from inedible biomass in a CELSS. During incineration CO2 is produced by oxidation of the organic components and this product can be directly utilized by plants. Water is concomitantly produced, requiring only a phase change for recovery. Recovery of inorganics is more difficult, requiring solubilization of the incinerator ash. The process of incineration followed by water solubilization of ash resulted in loss of 35% of the inorganics originally present in the biomass. Losses were attributed to volatilization (8%) and non-water-soluble ash (27%). All of the ash remaining following incineration could be solubilized with acid, with losses resulting from volatilization only. The recovery for individual elements varied. Elemental retention in the ash ranged from 100% of that present in the biomass for Ca, P, Mg, Na, and Si to 10% for Zn. The greatest water solubility was observed for potassium with recovery of approximately 77% of that present in the straw. Potassium represented 80% of the inorganic constituents in the wheat straw, and because of slightly greater solubility made up 86% of the water-soluble ash. Following incineration of inedible biomass from wheat, 65% of the inorganics originally present in the straw were recovered by water solubilization and 92% recovered by acid solubilization. Recovery of resources is more complex for pyrolysis and water extraction. Recovery of carbon, a resource of greater mass than the inorganic component of biomass, is more difficult following pyrolysis and water extraction of biomass. In both cases, additional processors would be required to provide products equivalent to those resulting from incineration alone. The carbon, water, and organic resources of inedible biomass are effectively separated and output in usable forms through incineration.

Bubenheim, David L.↗
NASA NTRS1997

Vacuum Gas Tungsten Arc Welding

A two-year program investigated vacuum gas tungsten arc welding (VGTAW) as a method to modify or improve the weldability of normally difficult-to-weld materials. After a vacuum chamber and GTAW power supply were modified, several difficult-to-weld materials were studied and key parameters developed. Finally, Incoloy 903 weld overlays were produced without microfissures.

Weeks, J. L.↗
NASA NTRS1997

Towards High-Assurance High-Performance Program Synthesis

Domain-specific automatic program synthesis tools, also called application generators, are playing an ever-increasing role in software development. However, high-performance application generators require difficult manual construction, and are very difficult to verify correct. This paper describes research and an implemented system that transforms program synthesis tools based on deductive synthesis into high-performance application generators. Deductive synthesis uses theorem-proving to construct solutions when given problem specifications. The verification condition for a deductive synthesis tool is essentially the soundness of the implemented inference rules. Theory Operationalization for Program Synthesis (TOPS) synergistically combines reformulation, automated mathematical classification, and compilation through partial deduction to decision procedures. It transforms general-purpose deductive synthesis, with exponential performance, into efficient special-purpose deductive synthesis, with near-linear performance. This paper describes our experience with and empirical results of PD(TH) theory-based partial deduction - in which partial deduction of a set of first-order formulae is performed within the context of a background theory. The implemented TOPS system currently performs a special variant of PD(TH) in which the compilation process results in the transformation of a set of first order formulae into the theory of an instantiated library decision procedure augmented by a compiled unit theory.

Lowry, Michael↗
NASA NTRS1997

Ion-Atom Cold Collisions and Atomic Clocks

Collisions between ultracold neutral atoms have for some time been the subject of investigation, initially with hydrogen and more recently with laser cooled alkali atoms. Advances in laser cooling and trapping of neutral atoms in a Magneto-Optic Trap (MOT) have made cold atoms available as the starting point for many laser cooled atomic physics investigations. The most spectacularly successful of these, the observation of Bose-Einstein Condensation (BEC) in a dilute ultra-cold spin polarized atomic vapor, has accelerated the study of cold collisions. Experimental and theoretical studies of BEC and the long range interaction between cold alkali atoms is at the boundary of atomic and low temperature physics. Such studies have been difficult and would not have been possible without the development and advancement of laser cooling and trapping of neutral atoms. By contrast, ion-atom interactions at low temperature, also very difficult to study prior to modern day laser cooling, have remained largely unexplored. But now, many laboratories worldwide have almost routine access to cold neutral atoms. The combined technologies of ion trapping, together with laser cooling of neutrals has made these studies experimentally feasible and several very important, novel applications might come out of such investigations . This paper is an investigation of ion-atom interactions in the cold and ultra-cold temperature regime. Some of the collisional ion-atom interactions present at room temperature are very much reduced in the low temperature regime. Reaction rates for charge transfer between unlike atoms, A + B(+) approaches A(+) + B, are expected to fall rapidly with temperature, approximately as T(sup 5/2). Thus, cold mixtures of atoms and ions are expected to coexist for very long times, unlike room temperature mixtures of the same ion-atom combination. Thus, it seems feasible to cool ions via collisions with laser cooled atoms. Many of the conventional collisional interactions, exploited as a useful tool at room temperature and higher, are greatly enhanced at low energy. For example, collisional spin transfer from one species of polarized atoms to another has long been a useful method for polarizing a sample of atoms where no other means was available. Because optical pumping cannot be used to polarize the nuclear spin of Xe-129 or He-3 (for use in nmr imaging of the lungs), the nuclear spins are polarized via collisions with an optically pumped Rb vapor in a cell containing both gases. In another case, a spin polarized thermal Cs beam was used to polarize the hyperfine states of trapped He(+)-3 ions in order to measure their hyperfine clock transition frequency. The absence of an x-ray light source to optically pump the ground state of the He(+)-3 ion necessitated this alternative state preparation. Similarly, Cd(+) and Sr(+) ions were spin-oriented via collisions in a cell with optically pumped Rb vapor. Resonant RF spin changing transitions in the ground state of the ions were detected by changes in the Rb resonance light absorption. Because cold collision spin exchange rates scale with temperature as T(sup -1/2) this technique is expected to be a far more powerful tool than the room temperature counterpart. This factor of 100 or more enhancement in spin exchange reaction rates at low temperatures is the basis for a novel trapped ion clock where laser cooled neutrals will cool, state select and monitor the ion clock transition. The advantage over conventional direct laser cooling of trapped ions is that the very expensive and cumbersome UV laser light sources, required to excite the ionic cooling transition, are effectively replaced by simple diode lasers.

Prestage, John D.↗
NASA NTRS1995

The Relative Reactivity of Deoxyribose and Ribose: Did DNA Come Before RNA?

If it is assumed that there was a precursor to the ribose-phosphate backbone of RNA in the preRNA world (such as peptide nucleic acid), then the entry of various sugars into the genetic material may be related to the stability and non-enzymatic reactivity of the aldose. The rate of decomposition of 2-deoxyribose has been determined to be 1/3 that of ribose. In addition we have measured the amount of free aldehyde by H-1 and C-13 NMR and find that it has approximately 0.15% free aldehyde compared to 0.05% for ribose at 25 C. This suggests that deoxyribose would be significantly more reactive with early bases in the absence of enzymes. This is confirmed by urazole and deoxyribose reacting to form the deoxynucleoside 45 times faster as 25 C than urazole reacts with ribose to form the Ribonucleoside. Urazole is a potential precursor of uracil and is a plausible prebiotic compound which reacts with aldoses to form nucleosides. Thus the non-enzymatic reactivity of deoxyribose would favor its early use over ribose until enzymes could change the relative reactivities. Most of the reasons that RNA is presumed to have come before DNA are extrapolations back from contemporary metabolism (e.g. the abundance of ribose based coenzymes, the biosynthesis of histidine, deoxyribonucleotides are synthesized from ribonucleotides, etc.). It is very difficult to reconstruct biochemical pathways much before the last common ancestor, and it is even more difficult to do more than guess at the biochemistry of very early self-replicating systems. Thus we believe that these reasons are not compelling and that the non-enzymatic chemistry may be more important than enzymatic pathways for constructing the earliest of biochemical pathways. While the RNA world has been discussed at great length, there has not been an exploration of the transition out of the RNA world. We have constructed many possible schemes of genetic takeover events from preRNA to modern DNA, RNA, protein system which could generate the RNA metabolic fossils we see today.

Dworkin, Jason P.↗
NASA NTRS1996

An Assessment of Molten Metal Detachment Hazards During Electron Beam Welding in the Space Shuttle Bay at LEO for the International Space Welding Experiment

In 1997, the United States [NASA] and the Paton Electric Welding Institute are scheduled to cooperate in a flight demonstration on the U.S. Space Shuttle to demonstrate the feasibility of welding in space for a possible repair option for the International Space Station Alpha. This endeavor, known as the International Space Welding Experiment (ISWE), will involve astronauts performing various welding exercises such as brazing, cutting, welding, and coating using an electron beam space welding system that was developed by the E.O. Paton Electric Welding Institute (PWI), Kiev Ukraine. This electron beam welding system known as the "Universal Weld System" consists of hand tools capable of brazing, cutting, autogeneous welding, and coating using an 8 kV (8000 volts) electron beam. The electron beam hand tools have also been developed by the Paton Welding Institute with greater capabilities than the original hand tool, including filler wire feeding, to be used with the Universal Weld System on the U.S. Space Shuttle Bay as part of ISWE. The hand tool(s) known as the Ukrainian Universal Hand [Electron Beam Welding] Tool (UHT) will be utilized for the ISWE Space Shuttle flight welding exercises to perform welding on various metal alloy samples. A total of 61 metal alloy samples, which include 304 stainless steel, Ti-6AI-4V, 2219 aluminum, and 5456 aluminum alloys, have been provided by NASA for the ISWE electron beam welding exercises using the UHT. These samples were chosen to replicate both the U.S. and Russian module materials. The ISWE requires extravehicular activity (EVA) of two astronauts to perform the space shuttle electron beam welding operations of the 61 alloy samples. This study was undertaken to determine if a hazard could exist with ISWE during the electron beam welding exercises in the Space Shuttle Bay using the Ukrainian Universal Weld System with the UHT. The safety issue has been raised with regard to molten metal detachments as a result of several possible causes such as welder procedural error, externally applied impulsive forces(s), filler wire entrainment and snap-out, cutting expulsion, and puddle expulsion. Molten metal detachment from either the weld/cut substrate or weld wire could present harm to a astronaut in the space environment it the detachment was ti burn through the fabric of the astronaut Extravehicular Mobility Unit (EMC). In this paper an experimental test was performed in a 4 ft. x 4 ft. vacuum chamber at MSFC enabling protective garment to be exposed to the molten metal drop detachments to over 12 inches. The chamber was evacuated to vacuum levels of at least 1 x 10(exp -5) torr (50 micro-torr) during operation of the 1.0 kW Universal Hand Tool (UHT). The UHT was manually operated at the power mode appropriate for each material and thickness. The space suit protective welding garment, made of Teflon fabric (10 oz. per yard) with a plain weave, was placed on the floor of the vacuum chamber to catch the molten metal drop detachments. A pendulum release mechanism consisting of four hammers, each weighing approximately 3.65 lbs, was used to apply an impact forces to the weld sample/plate during both the electron beam welding and cutting exercises. Measurements were made of the horizontal fling distances of the detached molten metal drops. The volume of a molten metal drop can also be estimated from the size of the cut. Utilizing equations, calculations were made to determine chande in surafec area (Delat a(surface)) for 304 stainless steel for cutting based on measurements of metal drop sizes at the cut edges. For the cut sample of 304 stainless steel based on measurement of the drop size at the edge, Delta-a(surface) was determined to be 0.0054 2 in . Calculations have indicated only a small amount of energy is required to detach a liquid metal drop. For example, approximately only 0.000005 ft-lb of energy is necessary to detach a liquid metal steel drop based on the above theoretical analysis. However, some of the energy will be absorbed by the plate before it reaches the metal drop. Based on the theoretical calculations, it was determined that during a weld cutting exercise, the titanium alloy would be the most difficult to detach molten metal droplets followed by stainless steel and then by aluminum. The results of the experimental effort have shown that molten metal will detach if large enough of a hammer blow is applied to the weld sample plate during the full penetration welding and cutting exercises. However, no molten metal detachments occurred as a result of the filler wire snap-out tests from the weld puddle since it was too difficult to cause the metal to flick-out from the pool. Molten metal detachments, though not large in size, did result from the direct application of the electron beam on the end of the filler weld wire.

Fragomeni, James M.↗
NASA NTRS1998

Direct Numerical Simulations of Boundary Layer Transition on a Flat Plate

In recent years the techniques of computational fluid dynamics (CFD) have been used to compute flows associated with geometrically complex configurations. However, success in terms of accuracy and reliability has been limited to cases where the effects of turbulence and transition could be modeled in a straightforward manner. Even in simple flows, the accurate computation of skin friction and heat transfer using existing turbulence models has proved to be a difficult task, one that has required extensive fine-tuning of the turbulence models used. In more complex flows (for example, in turbomachinery flows in which vortices and wakes impinge on airfoil surfaces causing periodic transitions from laminar to turbulent flow) the development of a model that accounts for all scales of turbulence and predicts the onset of transition is an extremely difficult task. Fortunately, current trends in computing suggest that it may be possible to perform direct simulations of turbulence and transition at moderate Reynolds numbers in some complex cases in the near future. This presentation will focus on direct simulations of transition and turbulence using high-order accurate finite-difference methods. The advantage of the finite-difference approach over spectral methods is that complex geometries can be treated in a straightforward manner. Additionally, finite-difference techniques are the prevailing methods in existing application codes. An application of high-order-accurate finite-difference methods to direct simulations of transition and turbulence in a spatially evolving boundary layer subjected to high levels of freestream turbulence will be presented.

Rai, Man Mohan↗
NASA NTRS1961

Rapid-Transition Tests of a 1/4-Scale Model of the VZ-2 Tilt-Wing Aircraft

An investigation of the longitudinal stability and control characteristics of a 1/4-scale model of the VZ-2 tilt-wing vertical-take-off- and-landing aircraft during rapid transitions has been made on the Langley control-line facility. Only the longitudinal characteristics were studied because with the control-line technique the other phases of the model motion are partially restrained. The rapid transitions from hovering to forward flight could be performed easily at any of the accelerations attempted; whereas, the transitions from forward flight to hovering were generally accompanied by a strong nose up pitching moment which at times was uncontrollable because of an inadequate amount of available pitch control. The model was more difficult to control during rapid decelerations than during slow decelerations and was also more difficult to control for rearward center-of-gravity conditions than for forward ones.

Tosti, Louis P.↗
NASA NTRS1961

Stability and Control Characteristics of a Small-Scale Model of an Aerial Vehicle Supported by Two Ducted Fans

An investigation has been made to determine the stability and control characteristics in hovering and in forward flight of a free-flight model representing a type of vertical-take-off-and-landing aircraft which utilizes two fixed ducted fans as its sole source of lift and propulsion. The model, having fans 28 inches in diameter, was considered to be approximately one-third the size of a full-scale aircraft. Control moments for most of the hovering tests and all the forward-flight tests were provided by remotely controlled compressed-air jets at the sides and ends of the model. For one brief phase of the hovering investigation a system of vanes in the duct slipstreams was substituted for the jets as a means of roll control. During the forward-flight tests, the model was flown with both the tandem and side-by-side duct arrangements. In hovering the model exhibited strongly divergent oscillations about the pitch and roll axes. The pitching oscillation of the tandem configuration was of a fairly long period and was not particularly difficult to control; the rolling oscillation, however, was of a relatively short period and was extremely difficult to control. Both oscillations could be completely eliminated by the addition of a sufficient amount of artificial damping. The control moments produced by the vane-type roll control system were weak and were accompanied by a side force of appreciable magnitude and undesirable direction. In forward flight the model required an undesirably large nose-down tilt angle for equilibrium at any appreciable speed. A vane was placed transversely in the slipstream of the forward duct of the tandem configuration in an attempt to reduce this tilt angle. The vane was effective in reducing the tilt angle but apparently caused an increase in the power requirements and in the angle-of-attack instability. Without the vane, a forward speed of 30 knots (full scale) required a nose-down tilt angle of about 300. A powerful pitch control moment was required not only to maintain the trim attitude but also to 2 overcome the effects of instability with angle of attack. Less pitch control moment was required for the tandem configuration than for the side-by-side configuration at any given forward speed. The instability in roll increased with forward speed. No forward speeds in excess of about 20 knots (full scale) were achieved until the artificial damping in roll and the yaw control moment were increased appreciably above values which had proved satisfactory for hovering flight.

Parlett, Lysle P.↗
NASA NTRS1999

Temperature Measurement of a Miniature Ceramic Heater in the Presence of an Extended Interfering Background Radiation Source Using a Multiwavelength Pyrometer

Temperature measurement of small (millimeter size) objects is generally difficult and demanding. Measurement involving ceramic materials using the traditional one- and two-color pyrometer is difficult because of their complex optical properties, such as low emissivity which may vary with both temperature and wavelength. Pyrometry applications in an environment with an interfering radiation source of extended dimension adds extra complexity to the process. We show that the multiwavelength pyrometer successfully measured the temperatures of a millimeter (mm) size ceramic heater under these demanding conditions.

Ng, Daniel↗
NASA NTRS1998

MAPS of Cancer

Our goal was to produce an interactive visualization from a mathematical model that successfully predicts metastases from head and neck cancer. We met this goal early in the project. The visualization is available for the public to view. Our work appears to fill a need for more information about this deadly disease. The idea of this project was to make an easily interpretable visualization based on what we call "functional maps" of disease. A functional map is a graphic summary of medical data, where distances between parts of the body are determined by the probability of disease, not by anatomical distances. Functional maps often beat little resemblance to anatomical maps, but they can be used to predict the spread of disease. The idea of modeling the spread of disease in an abstract multidimensional space is difficult for many people. Our goal was to make the important predictions easy to see. NASA must face this problem frequently: how to help laypersons and professionals see important trends in abstract, complex data. We took advantage of concepts perfected in NASA's graphics libraries. As an analogy, consider a functional map of early America. Suppose we choose travel times, rather than miles, as our measures of inter-city distances. For Abraham Lincoln, travel times would have been the more meaningful measure of separation between cities. In such a map New Orleans would be close to Memphis because of the Mississippi River. St. Louis would be close to Portland because of the Oregon Trail. Oklahoma City would be far from Little Rock because of the Cheyenne. Such a map would look puzzling to those of us who have always seen physical maps, but the functional map would be more useful in predicting the probabilities of inter-site transit. Continuing the analogy, we could predict the spread of social diseases such as gambling along the rivers and cattle rustling along the trails. We could simply print the functional map of America, but it would be more interesting to show meaningful patterns of dispersal. We had previously published the functional map of the head and neck, but it was difficult to explain to either patients or surgeons because that view of our body did not resemble anatomy. This discrepancy between functional and physical maps is just a mathematical restatement of the well-known fact that some diseases, such as head and neck cancer, spread in complex patterns, not always to the next nearest site. We had discovered that a computer could re-arrange anatomy so that this particular disease spreads to the next nearest site. The functional map explains over 95% of the metastases in 1400 patients. In a sense, we had graphed what our body "looks like" to a tumor. The tumor readily travels between adjacent areas in the functional map. The functional map is a succinct visual display of trends that are not easily appreciated in tables of probabilities.

Gray, Lincoln↗
NASA NTRS1999

Using Experiments to Build a Body of Knowledge

Experimentation in software engineering is important but difficult. One reason it is so difficult is that there are a large number of context variables, and so creating a cohesive understanding of experimental results requires a mechanism for motivating studies and integrating results. This paper argues for the necessity of a framework for organizing sets of related studies. With such a framework, experiments can be viewed as part of common families of studies, rather than being isolated events. Common families of studies can contribute to important and relevant hypotheses that may not be suggested by individual experiments. A framework also facilitates building knowledge in an incremental manner through the replication of experiments within families of studies. Building knowledge in this way requires a community of researchers that can replicate studies, vary context variables, and build abstract models that represent the common observations about the discipline. This paper also presents guidelines for lab packages, meant to encourage and support replications, that encapsulate materials, methods, and experiences concerning software engineering experiments.

Basili, Victor↗
NASA NTRS1999

Nondestructive Detection of Cracks in Ceramics Using Vicinal Illumination

Cracks and other defects in ceramic materials can be difficult or impossible to examine and photograph due to the extreme lack of contrast. A method for inspecting translucent ceramics using scattered light, also known as vicinal illumination, will be described. This method has been known in the ceramics industry for quite some time, but is not well known in the testing and failure analysis community. Electronics applications include substrates, packages, multilayer capacitors, and thin film resistors. Ceramic materials are used in electronic applications as microcircuit packages and substrates which carry signals and power between microcircuits. Fine cracks in ceramic materials can result in mechanical failures, electrical failures, and loss of hermeticity. Often, fine cracks are difficult or impossible to detect using standard nondestructive inspection techniques such as visual inspection, ultrasonic inspection, or vapor crack detection. Dye penetrant inspection is usually effective, but contaminates the part, which is unacceptable for space flight hardware. One effective nondestructive inspection method of detecting cracks involves examining the way in which light scatters through the ceramic material when viewed with a standard bright field reflected light microscope. This method, termed vicinal illumination, has been used for detecting cracks during failure analyses of several part types, and screening of space flight hardware. The technique has proven effective on several different types of ceramic materials as well. A related method for use with dark field equipment has also been used to successfully locate otherwise invisible cracks.

Hull, Scott M.↗
NASA NTRS1998

Polar Cap Plasma and Convection

This presentation will describe the character of the polar cap plasma in 10% AGU Spring 1998 particular the convection velocities at the perigee (about 1.8 Re) and apogee( about 8.9 Re) of Polar in relationship to Interplanetary Magnetic Field (IMF) and solar wind parameters. This plasma is thought to be due to several sources; the polar wind, cleft ion fountain, and auroral outflow. The plasma in the polar cap tends to be mostly field-aligned. At any given point in the polar cap, this plasma could be from a different regions since convection of magnetic field lines can transport this material. it is quite difficult to study such a phenomena with single point measurements. Current knowledge of the polar cap plasma obtained by in situ measurements will be presented along with recent results from the Polar mission. This study also examines the direct electrical coupling between the magnetosphere and ionosphere by comparing convection velocities measured by the Thermal Ion Dynamics Experiment (TIDE) and Magnetic Field Experiment (MFE) instruments in magnetosphere and measurements of the ionosphere by ground-based radars. At times such a comparison is difficult because the Polar satellite at apogee spends a large amount of time in the polar cap which is a region that is not coverage well by the current SuperDam coherent radars. This is impart due to the lack of irregularities that returns the radar signal.

Elliott, Heather A.↗
NASA NTRS1999

An Optimal Relation of Radar Reflectivity to Lightning Rate

Thunderstorms separate charge. Most places they lift positive charge or lower negative, a few places they lift negative or lower positive. The electrical generator is stronger in some parts of the cloud than in others. Our long term goal is to map this generator. Cloud physicists tell us that uncharged ice and water particles become charged by collision, and that the charge transferred depends on size, temperature and humidity. There is still some disagreement about exactly how the charge transferred depends on size, temperature, and humidity. In principle, if we knew this ice physics, and also knew the distribution of particles everywhere in the storm, and the winds everywhere and the temperature and humidity everywhere, then we could compute everywhere the electrical power of the thunderstorm generator. In practice it is difficult to know all these things, particularly the distribution of particles, so it is difficult to use real thunderstorms to falsify cloud electrification theories. We here take one small step towards computing that map of electrical generator power, by relating radar reflectivity profiles of 2000 storms to lightning flash rates of those storms. This small step by itself doesn't falsify any existing electrification theories; it merely places weak constraints on the relation of electric generator power to cloud ice.

Heckman, S.↗
NASA NTRS1993

Atmospheric Sulfur Hexafluoride: Sources, Sinks and Greenhouse Warming

Model calculations using estimated reaction rates of sulfur hexafluoride (SF6) with OH and 0('D) indicate that the atmospheric lifetime due to these processes may be very long (25,000 years). An upper limit for the UV cross section would suggest a photolysis lifetime much longer than 1000 years. The possibility of other removal mechanisms are discussed. The estimated lifetimes are consistent with other estimated values based on recent laboratory measurements. There appears to be no known natural source of SF6. An estimate of the current production rate of SF6 is about 5 kt/yr. Based on historical emission rates, we calculated a present-day atmospheric concentrations for SF6 of about 2.5 parts per trillion by volume (pptv) and compared the results with available atmospheric measurements. It is difficult to estimate the atmospheric lifetime of SF6 based on mass balance of the emission rate and observed abundance. There are large uncertainties concerning what portion of the SF6 is released to the atmosphere. Even if the emission rate were precisely known, it would be difficult to distinguish among lifetimes longer than 100 years since the current abundance of SF6 is due to emission in the past three decades. More information on the measured trends over the past decade and observed vertical and latitudinal distributions of SF6 in the lower stratosphere will help to narrow the uncertainty in the lifetime. Based on laboratory-measured IR absorption cross section for SF6, we showed that SF6 is about 3 times more effective as a greenhouse gas compared to CFC 11 on a per molecule basis. However, its effect on atmospheric warming will be minimal because of its very small concentration. We estimated the future concentration of SF6 at 2010 to be 8 and 10 pptv based on two projected emission scenarios. The corresponding equilibrium warming of 0.0035 C and 0.0043 C is to be compared with the estimated warming due to CO2 increase of about 0.8 C in the same period.

Sze, Nien Dak↗
NASA NTRS1999

Experimental and Numerical Study of Ammonium Perchlorate Counterflow Diffusion Flames

Many solid rocket propellants are based on a composite mixture of ammonium perchlorate (AP) oxidizer and polymeric binder fuels. In these propellants, complex three-dimensional diffusion flame structures between the AP and binder decomposition products, dependent upon the length scales of the heterogeneous mixture, drive the combustion via heat transfer back to the surface. Changing the AP crystal size changes the burn rate of such propellants. Large AP crystals are governed by the cooler AP self-deflagration flame and burn slowly, while small AP crystals are governed more by the hot diffusion flame with the binder and burn faster. This allows control of composite propellant ballistic properties via particle size variation. Previous measurements on these diffusion flames in the planar two-dimensional sandwich configuration yielded insight into controlling flame structure, but there are several drawbacks that make comparison with modeling difficult. First, the flames are two-dimensional and this makes modeling much more complex computationally than with one-dimensional problems, such as RDX self- and laser-supported deflagration. In addition, little is known about the nature, concentration, and evolution rates of the gaseous chemical species produced by the various binders as they decompose. This makes comparison with models quite difficult. Alternatively, counterflow flames provide an excellent geometric configuration within which AP/binder diffusion flames can be studied both experimentally and computationally.

Smooke, M. D.↗
NASA NTRS1999

Diagnostic Clast-Texture Criteria for Recognition of Impact Deposits

It is difficult to find definitive evidence for impact in the geological record because there are many endogenous geological processes that can produce diamictites similar to those generated by impact ejecta. The classic impact criteria of shock fabrics in certain minerals, and iridium layers, for example, may be either difficult to find, or long-since erased from the impact site (shock fabrics also anneal with time). It is important to be able to recognize impact-generated materials in order to understand earth's crustal development and biological evolution. In future exploration of Mars and other solar-system bodies, recognition of impact materials will be important for elucidating planetary evolution, planetary volatile inventories, and exobiological issues. The cobble depicted is typical of many that have been found in diamictite deposits in Belize generated by the Chicxulub K-T impact event. The pebbles are roughly-hewn in general shape with smoothed corners and edges. Surfaces are almost uniformly frosted (on both protuberances and hollows), but some asperities are glazed. Optical microscopy and thin-section petrographic microscopy reveal the frosting to be only a few microns thick, with a well-defined granular structure; grains are the same size as those composing the bulk of the limestone, but their clearer appearance may represent annealing. One or two adjacent pebble faces are often decorated with striated gouges and closely-spaced hemispherical depressions representing indentation hollows produced by well-rounded impacting clasts of up to 0.5 cm in diameter. Some of the impactors are still embedded in the cobble surface. Non-destructive x-ray diffraction techniques showed the impactors to be of the same mineralogy as the target cobble. We believe this unusual glazing and frosting to be related to the impact event, but this must be reconciled with its survival for over 60 my. since it is composed of one of the most alterable substances, CaCO3. We focus, however, on the non-fractured rounded pebbles that appear to have impacted the larger cobble as a swarm of clasts, probably encountered during ballistic flight. It cannot be defined whether the cobble swept through the pebble cloud, or the pebbles rained upon a slowermoving cobble. Two interesting questions arise: (1) Where did large numbers of such well rounded pebbles come from in the ejecta curtain?, and (2) How did they embed themselves in a nominally brittle rock without suffering damage? Are the well-rounded pebbles crystalline (devitrified) melt spherules? Further investigations are in progress. If the cobble was cold and brittle, impact of well-rounded pebbles would have produced Hertzian fracture patterns (a) in the virtually elastically isotropic cobble target. For penetration depths of about 0.5 of the impactor diameter, the pebbles would require a relative impact velocity sufficient to cause pebble fragmentation and crushing, and the development of a complex Hertzian-Boussinesq fracture field (b) involving deep fracturing and lateral surface spalling (impact velocities > 50 m/s). The existing relationship could only evolve by the impact of cold, hard pebbles into a soft, plastic cobble surface (c). For limestone to have been plastic, it must have been at elevated temperature, but to prevent calcification of the material, the ambient pressure must also have been elevated. This would be possible either in the impact's gas plume, or within the confines of a thin aerodynamically-produced shock bow generated by supersonic ballistic motion of the cobble. In the latter case, it is implied that the cobble swept through the pebbles rather than vice-versa. Although there are high T-P conditions associated with volcanism, such textures have not been reported on volcaniclastic materials, nor from other high T-P environments; e.g., metamorphic (as far as the authors are aware). We propose that this very easily recognizable embedding and indentation surface texture can be used as a diagnostic criterion for the recognition of impact ejecta. The term "peening texture" is suggested, because it is absolutely analogous to the plastic-deformation induced, metal-surface textures generated by ball-bearing bombardment used in engineering metallurgy to work-harden metal surfaces. Additional information is contained in the original (Figures).

Marshall, J. R.↗