Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “defective engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Modeling of interdendritic porosity defects in an integrated computational materials engineering approach for metal casting

Modeling and simulation of multiphysical phenomena needs to be considered in the design and optimization of mechanical properties of cast components in order to accelerate the introduction of new cast alloys. The data on casting defects, including microstructure features, is crucial for evaluating the final performance-related properties of the component. Here in this paper, the required models for the prediction of interdendritic casting defects, such as microporosity and hot tears, are reviewed. The data on calculated solidification shrinkage is presented and its effects on microporosity levels discussed. Numerical simulation results for microporosity are presented for A356, 356 and 319 aluminum alloys using ProCAST TM software. The calculated pressure drop of the interdendritic liquid was observed to be quite significant and the regions of high-pressure drop can be used as an indicator of the severity of interdendritic microporosity defects.

36 MATERIALS SCIENCE↗

MoS 2 nanosheet integrated electrodes with engineered 1T-2H phases and defects for efficient hydrogen production in practical PEM electrolysis

Low electrical conductivity and poor accessibility of MoS 2 reaction sites raise great challenges in maximizing the triple-phase-boundary (TPB) sites of MoS 2 -based electrodes and minimizing ohmic losses for efficient hydrogen evolution reaction (HER) in practical proton exchange membrane (PEM) water electrolysis. Herein, we report a scalable hydrothermal approach to fabricate ionomer-free integrated electrodes with engineered 1 T-2 H heterophase and defect-rich MoS 2 nanosheets (MoS 2 NSs) in-situ grown onto the carbon fiber paper (CFP). With an ultralow loading of 0.14 mg/cm 2 , a small voltage of 2.25 V was obtained at 2000 mA/cm 2 in a practical cell with Nafion115 membrane, which outperforms all previously reported high-loading non-precious catalyst-based electrodes. Impressively, it shows 44 times higher mass activity than a high-loading and ionomer-mixed MoS 2 assemblies electrode. Furthermore, this work builds a bridge from catalyst optimization to electrode fabrication and provides a promising direction for improving intrinsic catalytic activity, electrode conductivity and stability for practical PEM water electrolysis.

1T-2H heterophase↗

Engineering the formation of spin-defects from first principles

The full realization of spin qubits for quantum technologies relies on the ability to control and design the formation processes of spin defects in semiconductors and insulators. We present a computational protocol to investigate the synthesis of point-defects at the atomistic level, and we apply it to the study of a promising spin-qubit in silicon carbide, the divacancy (VV). Our strategy combines electronic structure calculations based on density functional theory and enhanced sampling techniques coupled with first principles molecular dynamics. We predict the optimal annealing temperatures for the formation of VVs at high temperature and show how to engineer the Fermi level of the material to optimize the defect’s yield for several polytypes of silicon carbide. Our results are in excellent agreement with available experimental data and provide novel atomistic insights into point defect formation and annihilation processes as a function of temperature.

36 MATERIALS SCIENCE↗

A Modified Rabbit Ulna Defect Model for Evaluating Periosteal Substitutes in Bone Engineering: A Pilot Study

The present work defines a modified critical size rabbit ulna defect model for bone regeneration in which a non-resorbable barrier membrane was used to separate the radius from the ulna to create a valid model for evaluation of tissue-engineered periosteal substitutes. Eight rabbits divided into two groups were used. Critical defects (15 mm) were made in the ulna completely eliminating periosteum. For group I, defects were filled with a nanohydroxyapatite poly(ester urethane) scaffold soaked in PBS and left as such (group Ia) or wrapped with a tissue-engineered periosteal substitute (group Ib). For group II, an expanded-polytetrafluoroethylene (e-PTFE) (GORE-TEX{sup ®}) membrane was inserted around the radius then the defects received either scaffold alone (group IIa) or scaffold wrapped with periosteal substitute (group IIb). Animals were euthanized after 12–16 weeks, and bone regeneration was evaluated by radiography, computed microtomography (μCT), and histology. In the first group, we observed formation of radio-ulnar synostosis irrespective of the treatment. This was completely eliminated upon placement of the e-PTFE (GORE-TEX{sup ®}) membrane in the second group of animals. In conclusion, modification of the model using a non-resorbable e-PTFE membrane to isolate the ulna from the radius was a valuable addition allowing for objective evaluation of the tissue-engineered periosteal substitute.

60 APPLIED LIFE SCIENCES↗

Mechanical properties of irradiated single-layer graphene

The mechanical properties of irradiated single-layer graphene sheets are determined as a function of inserted vacancy concentration. We find that the vacancy-induced crystalline-to-amorphous transition is accompanied by a brittle-to-ductile transition in the failure response of irradiated graphene sheets for inserted vacancy concentrations of 8%-12%. While point defects and larger voids appreciably degrade the strength of pristine graphene, we find that even heavily damaged samples ({approx}20% vacancies) exhibit tensile strengths of {approx}30 GPa, in significant excess of those typical of engineering materials. Our results suggest that defect engineering of graphene is feasible without incurring a complete loss of its desirable mechanical properties.

36 MATERIALS SCIENCE↗

Grain engineering for efficient near-infrared perovskite light-emitting diodes

Metal halide perovskites show promise for next-generation light-emitting diodes, particularly in the near-infrared range, where they outperform organic and quantum-dot counterparts. However, they still fall short of costly III-V semiconductor devices, which achieve external quantum efficiencies above 30% with high brightness. Among several factors, controlling grain growth and nanoscale morphology is crucial for further enhancing device performance. This study presents a grain engineering methodology that combines solvent engineering and heterostructure construction to improve light outcoupling efficiency and defect passivation. Solvent engineering enables precise control over grain size and distribution, increasing light outcoupling to ~40%. Constructing 2D/3D heterostructures with a conjugated cation reduces defect densities and accelerates radiative recombination. The resulting near-infrared perovskite light-emitting diodes achieve a peak external quantum efficiency of 31.4% and demonstrate a maximum brightness of 929 W sr -1 m -2 . These findings indicate that perovskite light-emitting diodes have potential as cost-effective, high-performance near-infrared light sources for practical applications.

42 ENGINEERING↗

Corrosion Detection LDRD Seedling (Final Report)

Automation techniques for recognizing material defects are very common in fields like infrastructure survey and civil engineering; however, the defects are usually easily distinguishable from their background, on a larger scale (e.g. cement bridges), and very specific. Extracting information about a defect that is near or equal to the background of the data can be extremely difficult. Images with heavy background corrosion, pitting, cracking, and man-made defects (such as welding) makes extracting information on a specific defect near-impossible. This is especially true when the defect is on the micron level and the dynamic range of your image taking instrument is low. So, a simplified, Java-based Fiji™ (ImageJ) defect detection program, dependent on a ‘flag’ system, was proposed for data that has a micron level hairline crack that is near or equal to the background. The utilization of the built-in functions, plugins, and macro scripting capability of the Java-based software sends a series of flags to the user that help to identify if the surface contains a defect of interest and to characterize that defect.

42 ENGINEERING↗

Sonic IR crack detection of aircraft turbine engine blades with multi-frequency ultrasound excitations

Effectively and accurately detecting cracks or defects in critical engine components, such as turbine engine blades, is very important for aircraft safety. Sonic Infrared (IR) Imaging is such a technology with great potential for these applications. This technology combines ultrasound excitation and IR imaging to identify cracks and flaws in targets. In general, failure of engine components, such as blades, begins with tiny cracks. Since the attenuation of the ultrasound wave propagation in turbine engine blades is small, the efficiency of crack detection in turbine engine blades can be quite high. The authors at Wayne State University have been developing the technology as a reliable tool for the future field use in aircraft engines and engine parts. One part of the development is to use finite element modeling to assist our understanding of effects of different parameters on crack heating while experimentally hard to achieve. The development has been focused with single frequency ultrasound excitation and some results have been presented in a previous conference. We are currently working on multi-frequency excitation models. The study will provide results and insights of the efficiency of different frequency excitation sources to foster the development of the technology for crack detection in aircraft engine components.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Ultrasonic Lamb Wave Inspection of Composite Defects

Composites have been extensively used in aerospace engineering due to their advantages of light weight, high strength, and engineering design flexibility. Manufacturing defects such as wrinkle and porosity can affect the performance of the composites and may lead to failure in the end, while damage such as delamination, fiber fraction, and matrix cracking can directly cause failure of the composites. In this paper, a Lamb wave based nonintrusive nondestructive evaluation system, which employs piezoelectric transducer for actuation and scanning laser Doppler vibrometer for wavefield sensing, is presented for typical composite defect and damage inspection and evaluation. Two composite panels with different geometry (flat or curved) and with various embedded defects (wrinkle and delamination) are inspected using the nonintrusive Lamb wave system. Both the wrinkles and delamination are detected from the wavefield and approximately quantified through wavefield imaging methods.

Wrinkles↗

Strain engineered pyrochlore at high pressure

Strain engineering is a promising method for next-generation materials processing techniques. Here, we use mechanical milling and annealing followed by compression in diamond anvil cell to tailor the intrinsic and extrinsic strain in pyrochlore, Dy 2 Ti 2 O 7 and Dy 2 Zr 2 O 7 . Raman spectroscopy, X-ray pair distribution function analysis, and X-ray diffraction were used to characterize atomic order over short-, medium-, and long-range spatial scales, respectively, under ambient conditions. Raman spectroscopy and X-ray diffraction were further employed to interrogate the material in situ at high pressure. High-pressure behavior is found to depend on the species and concentration of defects in the sample at ambient conditions. Overall, we show that defects can be engineered to lower the phase transformation onset pressure by ~50% in the ordered pyrochlore Dy 2 Zr 2 O 7 , and lower the phase transformation completion pressure by ~20% in the disordered pyrochlore Dy 2 Zr 2 O 7 . These improvements are achieved without significantly sacrificing mechanical integrity, as characterized by bulk modulus.

36 MATERIALS SCIENCE↗

Quantifying the effect of tow architecture variability on the performance of biaxially braided composite tubes

Targeted experiments are performed with stereoscopic digital image correlation to quantify the effect of irregular braid structure on the local surface mechanical response of carbon-fiber reinforced epoxy composite tubes. Virtual models comparing both nonuniform and uniform tow structure of the outer braid of each specimen are integrated into numerical simulations similar to experiments. Experimental and numerical results agree well. Statistical tests are used to support correlations between as-manufactured braid variation ranges to local increases in stress up to 18% compared to an ideal, uniform structure in the elastic regime. Results support improved manufacturing and modeling efforts of defect sensitive braided composites.

36 MATERIALS SCIENCE↗

Highly Crystalline and Porous Borocarbonitrides as Metal‐Free Catalysts for Boosted N‐Heterocycle Dehydrogenation

Safe and efficient hydrogen storage is pivotal for enabling a clean hydrogen economy. Liquid organic hydrogen carriers (LOHCs) offer a practical solution, but their deployment is hindered by the lack of highly active and economical dehydrogenation catalysts. In this work, we report a metal‐free catalyst design that overcomes the long‐standing trade‐off between crystallinity and surface area in two‐dimensional frameworks for highly efficient dehydrogenation of LOHCs. A flux‐assisted reconstruction strategy transforms amorphous borocarbonitrides (AM‐BCN) into highly crystalline, defect‐rich BCN nanosheets (C‐BCN) with large surface area and accessible porosity, as confirmed by complementary spectroscopic, x‐ray, and neutron analyses. C‐BCN catalyzes the acceptor‐less dehydrogenation of aza‐fused LOHCs with quantitative hydrogen release under mild conditions, outperforming AM‐BCN and previously reported metal‐free scaffolds. Mechanistic insights from x‐ray, neutron scattering, and theoretical calculations identify open C‐B‐N and N‐B‐N defect motifs as the primary active sites. This work establishes a generalizable strategy to engineer crystalline, porous, defect‐rich two‐dimensional lattices and demonstrates a highly active metal‐free platform for LOHC dehydrogenation with high‐purity H 2 generation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Recent tests on the Carter small reciprocating steam engines

The Jay Carter Enterprises (JCE) Paratransit Vehicle steam engine was tested over a range of conditions which might be experienced by the power converter subsystem of the Small Community Solar Thermal Power Experiment. Some difficulties were encountered getting the engine ready for testing. These difficulties were related to the five year dormancy of the entire system and to incomplete development work that had been going on at the time of cessation of steam engine work at JCE. Other difficulties were related to the fact that the particular expander being tested never ran before and possessed some manufacturing defects. Nevertheless, the engine was operated successfully and results of testing do verify results of computer simulations of the engine in regard to the effect of temperature and power level variations. Engine efficiency was good but generally lower than expected and performance dropped as testing continued. The effect of change in expansion ratio was not demonstrated because of deterioration in engine performance. Post-test inspection revealed numerous correctable defects.

Kiceniuk, T.↗

Native Defects Hybridization and Electronic Transport in Cu 2 Se–CuGaSe 2 Hierarchical Composites

Engineering the energy distribution of electronic defects in semiconductors can afford the coexistence of degenerate and nondegenerate transport behavior. By leveraging native defects in Cu 2 Se and CuGaSe 2 phases, the tunability of the concentration and energy distribution of active electronic defects in hierarchical (1-x)Cu 2 Se-(x)CuGaSe 2 composites is demonstrated. This study found that the electrical conductivity of various composites decreases with rising temperature indicating degenerate semiconducting behavior, whereas the carrier density increases with temperature, which is consistent with non-degenerate semiconductivity. Remarkably, this study found that while the carrier density and electrical conductivity drop with the increasing CuGaSe 2 content for samples with x ≤ 0.45 is consistent with an increase in the activation energy of “active” electronic defects, the sudden increase by 140% in the electrical conductivity and by 109% in the carrier density for near equimolar composition suggests the formation of a large density of electronic defects with lower activation energy. This unusual behavior is understood within the context of the hybridization of coexisting native electronic defects to form degenerate hybrid acceptor states with lower activation energy. The reported unique electronic transport can be leveraged for the development of more versatile electronic and optoelectronic devices with superior performance.

36 MATERIALS SCIENCE↗

CASTING DEFECT MODELING IN AN INTEGRATED COMPUTATIONAL MATERIALS ENGINEERING APPROACH

To accelerate the introduction of new cast alloys, the simultaneous modeling and simulation of multiphysical phenomena needs to be considered in the design and optimization of mechanical properties of cast components. The required models related to casting defects, such as microporosity and hot tears, are reviewed. Three aluminum alloys are considered A356, 356 and 319. The data on calculated solidification shrinkage is presented and its effects on microporosity levels discussed. Examples are given for predicting microporosity defects and microstructure distribution for a plate casting. Models to predict fatigue life and yield stress are briefly highlighted here for the sake of completion and to illustrate how the length scales of the microstructure features as well as porosity defects are taken into account for modeling the mechanical properties. Thus, the data on casting defects, including microstructure features, is crucial for evaluating the final performance-related properties of the component. ACKNOWLEDGEMENTS This work was performed under a Cooperative Research and Development Agreement (CRADA) with the Nemak Inc., and Chrysler Co. for the project "High Performance Cast Aluminum Alloys for Next Generation Passenger Vehicle Engines. The author would also like to thank Amit Shyam for reviewing the paper and Andres Rodriguez of Nemak Inc. Research sponsored by the U. S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Vehicle Technologies Office, as part of the Propulsion Materials Program under contract DE-AC05-00OR22725 with UT-Battelle, LLC. Part of this research was conducted through the Oak Ridge National Laboratory's High Temperature Materials Laboratory User Program, which is sponsored by the U. S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Vehicle Technologies Program.

Sabau, Adrian S↗

Effects of Defects on Band Structure and Excitons in WS 2 Revealed by Nanoscale Photoemission Spectroscopy

Two-dimensional materials with engineered composition and structure will provide designer materials beyond conventional semiconductors. Yet, the potentials of defect engineering remain largely untapped, because it hinges on a precise understanding of electronic structure and excitonic properties, which are not yet predictable by theory alone. In this report, we use correlative, nanoscale photoemission spectroscopy to visualize how local introduction of defects modifies electronic and excitonic properties of two-dimensional materials at the nanoscale. As a model system, we study chemical vapor deposition grown monolayer WS 2 , a prototypical, direct gap, two-dimensional semiconductor. By cross-correlating nanoscale angle-resolved photoemission spectroscopy, core level spectroscopy, and photoluminescence, we unravel how local variations in defect density influence electronic structure, lateral band alignment, and excitonic phenomena in synthetic WS 2 monolayers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nanoscale Engineering Of Radiation Tolerant Silicon Carbide

Radiation tolerance is determined by how effectively the microstructure can remove point defects produced by irradiation. Engineered nanocrystalline SiC with a high-density of stacking faults (SFs) has significantly enhanced recombination of interstitials and vacancies, leading to selfhealing of irradiation-induced defects. While single crystal SiC readily undergoes an irradiationinduced crystalline to amorphous transformation at room temperature, the nano-engineered SiC with a high-density of SFs exhibits more than an order of magnitude increase in radiation resistance. Molecular dynamics simulations of collision cascades show that the nano-layered SFs lead to enhanced mobility of interstitial Si atoms. The remarkable radiation resistance in the nano-engineered SiC is attributed to the high-density of SFs within nano-sized grain structures that significantly enhance point defect annihilation.

Environmental Molecular Sciences Laboratory↗

Work function engineering of single layer graphene by irradiation-induced defects

We report the tuning of electrical properties of single layer graphene by α-beam irradiation. As the defect density increases upon irradiation, the surface potential of the graphene changes, as determined by Kelvin probe force microscopy and Raman spectroscopy studies. X-ray photoelectron spectroscopy studies indicate that the formation of C/O bonding is promoted as the dose of irradiation increases when at atmospheric conditions. Our results show that the surface potential of the graphene can be engineered by introducing atomic-scale defects via irradiation with high-energy particles.

36 MATERIALS SCIENCE↗