Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “coupling constant”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

High performance high-power textured Mn/Cu-doped PIN-PMN-PT ceramics

Piezoelectric ceramics with combinatory soft and hard characteristics are highly desired for high-power applications. However, it remains grand challenge to achieve simultaneous presence of hard (e.g. high coercive field, E c ; high mechanical quality factor, Q m ) and soft (e.g. high piezoelectric constant, d; high electromechanical coupling factor, k) piezoelectric properties in piezoelectric ceramics since the mechanism controlling the hard behavior (pinned domain walls) will significantly reduce the soft behavior. Here, we address this grand challenge and demonstrate <001> textured MnO 2 and CuO co-doped Pb(In 1/2 Nb 1/2 )O 3- Pb(Mg 1/3 Nb 2/3 )O 3- PbTiO 3 (PIN-PMN-PT) ceramics exhibiting ultrahigh combined soft and hard piezoelectric properties (d 33 = 713 pC N –1 , k 31 = 0.52, Q m ≈950, E c = 9.6 kV cm –1 , tan δ = 0.45%). The outstanding electromechanical properties are explained by considering composition/phase selection, crystallographic anisotropy and defect engineering. Phase-field model in conjunction with high resolution electron microscopy and diffraction techniques is utilized to delineate the contributions arising from intrinsic piezoelectric response, domain dynamics, and local structural heterogeneity. Furthermore, these results will have significant impact in the development of high-power transducers and actuators.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Study of the magnetic interface and its effect in Fe/NiFe bilayers of alternating order

We present a comprehensive study on the magnetization reversal in the Fe/NiFe bilayer system by alternating the order of the magnetic layers. All the samples show growth-induced uniaxial magnetic anisotropy due to the oblique angle deposition technique. Strong interfacial exchange coupling between the Fe and NiFe layers leads to single-phase hysteresis loops in the bilayer system. The strength of coupling being dependent on the interface changes upon alternating the order of magnetic layers. The magnetic parameters such as coercivity H C , and anisotropy field H K become almost doubled when a NiFe layer is grown over the Fe layers. This enhancement in the magnetic parameters is primarily dependent on the increase of the thickness and magnetic moment of the Fe–NiFe interfacial layer as revealed from the polarized neutron reflectivity (PNR) data of the bilayer samples. The difference in the thickness and magnetization of the Fe–NiFe interfacial layer indicates the modification of the microstructure by alternating the order of the magnetic layers of the bilayers. The interfacial magnetic moment increased by almost 18% when the NiFe layer was grown over the Fe layer. In spite of the different values of anisotropy fields and modified interfacial exchange coupling, the Gilbert damping constant values of the ferromagnetic bilayers remain similar to the single NiFe layer.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Solvent influence on non-adiabatic interfacial electron transfer at conductive oxide electrolyte interfaces

The kinetics for interfacial electron transfer (ET) from a transparent conductive oxide (tin-doped indium oxide, ITO, Sn:In 2 O 3 ) to molecular acceptors 4-[N,N-di(p-tolyl)amino]benzylphosphonic acid, TPA, and [Ru II (bpy) 2 (4,4' -(PO 3 H 2 ) 2 -bpy)] 2+ , RuP, positioned at variable distances within and beyond the electric double layer (EDL), were quantified in benzonitrile and methanol by nanosecond absorption spectroscopy as a function of the thermodynamic driving force, -ΔG ° . Relevant ET parameters such as the rate constant, k et , reorganization energy, λ, and electronic coupling, Hab, were extracted from the kinetic data. Overall, k et increased as the distance between the molecular acceptor and the conductor decreased. For redox active molecules within the Helmholtz planes of the EDL, k et was nearly independent of -ΔG° , consistent with a negligibly small λ value. Rips–Jortner analysis revealed a non-adiabatic electron transfer mechanism consistent with H ab < 1 cm -1 . The data indicate that the barrier for electron transfer is greatly diminished at the conductor–electrolyte interface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1989

Conformal scalar field wormholes

The Euclidian Einstein equations with a cosmological constant and a conformally coupled scalar field are solved, taking the metric to be of the Robertson-Walker type. In the case Lambda = 0, solutions are found which represent a wormhole connecting two asymptotically flat Euclidian regions. In the case Lambda greater than 0, the solutions represent tunneling from a small Tolman-like universe to a large Robertson-Walker universe.

Halliwell, Jonathan J.↗
NASA NTRS1994

Dendritic Growth Velocities in Microgravity

We measured dendritic tip velocities in pure succinonitrile (SCN) in microgravity. using a sequence of telemetered binary images sent to Earth from the Space Shuttle Columbia (STS-62). Growth velocities were measured as a function of the supercooling over the range 0.05-1.5 K. Microgravity observations show that buoyancy-induced convection alters the growth kinetics of SCN dendrites at supercooling as high as 1.3 K. Also, the dendrite velocity data measured under microgravity agree well with the Ivantsov paraboloidal diffusion solution when coupled to a scaling constant of sigma(sup *) = 0.0157.

Glicksman, M. E.↗
NASA NTRS2000

Effect of Elevated Pressure on the Heat Transfer and Power Requirements During Bridgman Growth of PMN-PT Crystals

Performance of the furnace during Bridgman growth of the lead magnesium niobate-lead titanate crystal (PMN-PT) is analyzed. PMN-PT is electrostrictive ceramic that has near ideal strain-voltage function. Furthermore piezoelectric (2000 to 2300 pC/N) and coupling (92 to 95%) constants are exceptionally good. Due to these properties PMN-PT has wide range of applications - from sonars to transducers in a high precision optical systems. In this research first attempt to crystallize PMN-PT in a Mellen type vertical Bridgman furnace was not successful, as melting temperature of precursor materials was not achieved. At this point choice was between building a new more powerful facility or finding ways to enhance performance of the existing furnace. Besides adjusting power supply to the individual heating elements, redesigning ampoule holding cartridge and improving furnace insulation one more radical improvement was proposed. The entire furnace was placed into the high pressure chamber. Further experiments confirmed that temperature inside the furnace was increased sufficiently to melt precursor materials to obtain PMN-PT. Numerical modeling is undertaken to find limitations of this technique and to predict temperature distribution inside the ampoule. It is of interest also to account for main factors contributing to a higher temperatures achieved in the furnace under the higher pressure (up to 10 atm.). Numerical model of the furnace is based on general purpose finite - element code FIDAP and on previous efforts to model Bridgman type furnace with multiply heaters. In order to account for all heat transfer mechanism involved - conduction, convection and radiation - different parts of the furnace are modeled in accordance with expected dominant mode of heat transfer - conduction in the solid parts, conduction and radiation in the ampoule, gas convection and conduction in the furnace openings complemented with wall-to-wall radiation. Because of these complicating factors, dimensional rather than non-dimensional modeling is performed using steady-state 2-D and 3-D models. Particular attention is paid to the modeling of radiation in a semitransparent material of ampoule 7 sapphire. The radiation model is validated by solving realistic test problem - conduction and radiation heat transfer in the fused quartz. Results are in agreement with both experimental and analytical data.

Bune, Andris↗
NASA NTRS1992

Coupling device with improved thermal interface

The primary object of the present invention is to provide a simple, reliable, and lightweight coupling that will also have an efficient thermal interface. A further object of the invention is to provide a coupling that is capable of blind mating with little or no insertion forces. Another object of the invention is to provide a coupling that acts as a thermal regulator to maintain a constant temperature on one side of the coupling. Another object of the invention is to increase the available surface area of a coupling thus providing a larger area for the conduction of heat across the thermal interface. Another object of the invention is to provide a fluidic coupling that has no fluid passing across the interface, thus reducing the likelihood of leaks and contamination. The foregoing objects are achieved by utilizing, as in the prior art, a hot area (at an elevated temperature as compared to a cold area) with a need to remove excess heat from the hot area to a cold area. In this device, the thermal interface will occur not on a planar horizontal surface, but along a non-planar vertical surface, which will reduce the reaction forces and increase the thermal conductivity of the device. One non-planar surface is a surface on a cold pin extending from the cold area and the other non-planar surface is a surface on a hot pin extending from the hot area. The cold pin is fixed and does not move while the hot pin is a flexible member and its movement towards the cold pin will bring the two non-planar surfaces together forming the thermal interface. The actuating member for the device is a shape-memory actuation wire which is attached through an aperture to the hot pin and through another aperture to an actuation wire retainer. By properly programming the actuation wire, heat from the hot area will cause the actuation wire to bend the hot wire. Heat from the hot area will cause the actuation wire to bend the hot pin towards the cold pin forming the coupling and the desired thermal interface. The shape-memory actuation wire is made of a shape-memory-effect alloy such as Nitinol.

Milam, Malcolm Bruce↗
NASA NTRS1994

Orientation of human optokinetic nystagmus to gravity: a model-based approach

Optokinetic nystagmus (OKN) was induced by having subjects watch a moving display in a binocular, head-fixed apparatus. The display was composed of 3.3 degrees stripes moving at 35 degrees/s for 45 s. It subtended 88 degrees horizontally by 72 degrees vertically of the central visual field and could be oriented to rotate about axes that were upright or tilted 45 degrees or 90 degrees. The head was held upright or was tilted 45 degrees left or right on the body during stimulation. Head-horizontal (yaw axis) and head-vertical (pitch axis) components of OKN were recorded with electro-oculography (EOG). Slow phase velocity vectors were determined and compared with the axis of stimulation and the spatial vertical (gravity axis). With the head upright, the axis of eye rotation during yaw axis OKN was coincident with the stimulus axis and the spatial vertical. With the head tilted, a significant vertical component of eye velocity appeared during yaw axis stimulation. As a result the axis of eye rotation shifted from the stimulus axis toward the spatial vertical. Vertical components developed within 1-2 s of stimulus onset and persisted until the end of stimulation. In the six subjects there was a mean shift of the axis of eye rotation during yaw axis stimulation of approximately 18 degrees with the head tilted 45 degrees on the body. Oblique optokinetic stimulation with the head upright was associated with a mean shift of the axis of eye rotation toward the spatial vertical of 9.2 degrees. When the head was tilted and the same oblique stimulation was given, the axis of eye rotation rotated to the other side of the spatial vertical by 5.4 degrees. This counterrotation of the axis of eye rotation is similar to the "Muller (E) effect," in which the perception of the upright is counterrotated to the opposite side of the spatial vertical when subjects are tilted in darkness. The data were simulated by a model of OKN with a "direct" and "indirect" pathway. It was assumed that the direct visual pathway is oriented in a body, not a spatial frame of reference. Despite the short optokinetic after-nystagmus time constants, strong horizontal to vertical cross-coupling could be produced if the horizontal and vertical time constants were in proper ratio and there were no suppression of nystagmus in directions orthogonal to the stimulus direction. The model demonstrates that the spatial orientation of OKN can be achieved by restructuring the system matrix of velocity storage. We conclude that an important function of velocity storage is to orient slow-phase velocity toward the spatial vertical during movement in a terrestrial environment.

Non-NASA Center↗
NASA NTRS2012

Loads Correlation of a Full-Scale UH-60A Airloads Rotor in a Wind Tunnel

Wind tunnel measurements of the rotor trim, blade airloads, and structural loads of a full-scale UH-60A Black Hawk main rotor are compared with calculations obtained using the comprehensive rotorcraft analysis CAMRAD II and a coupled CAMRAD II/OVERFLOW 2 analysis. A speed sweep at constant lift up to an advance ratio of 0.4 and a thrust sweep at constant speed into deep stall are investigated. The coupled analysis shows significant improvement over comprehensive analysis. Normal force phase is better captured and pitching moment magnitudes are better predicted including the magnitude and phase of the two stall events in the fourth quadrant at the deeply stalled condition. Structural loads are, in general, improved with the coupled analysis, but the magnitude of chord bending moment is still significantly underpredicted. As there are three modes around 4 and 5/rev frequencies, the structural responses to the 5/rev airloads due to dynamic stall are magnified and thus care must be taken in the analysis of the deeply stalled condition.

Yeo, Hyeonsoo↗
DOE OSTI2025

Higgs Inflation and the Electroweak Gauge Sector

Abstract We introduce a method that allows the Higgs to be the inflaton. The Higgs is considered as a pseudo‐Nambu‐Goldstone (pNG) boson of a global coset symmetry , which is spontaneously breaks at an energy scale . A suitable Chern−Simons (CS) interaction is given to it, with representing the dimensionless CS coupling strength and an decay constant. As a result, slow‐roll inflation occurs via ‐induced friction down a steep sinusoidal potential. To obey electroweak symmetry, the lowest‐order CS interaction is required to be quadratic in the Higgs, with the coupling strength . Higher‐order interaction terms keep the full Lagrangian nearly invariant under the approximate pNG shift symmetry. Employing the simplest symmetry coset , ‐folds of inflation occur when . Successfully explaining inflation necessitates small values of the decay constant, ; this in turn requires large , which is ruled out by electric dipole measurements. Although the electroweak hierarchy problem while achieving successful inflation, the real benefit is found in providing a different path to identifying the Higgs as the inflaton, outside the standard modified‐gravity framework.

Alexander, Stephon [Brown Center for Theoretical P↗
NASA NTRS1986

The effective intensity of Coriolis, cross-coupling stimulation is gravitoinertial force dependent - Implications for space motion sickness

The effect of gravity on the severity of the Coriolis-induced motion sickness was investigated in ten individuals subjected to high and low G-force phases of parabolic flight maneuvers using constant level Coriolis, cross-coupled angular acceleration stimulation. Using seven levels of severity in the diagnosis of motion sickness, it was found that the subjects were less susceptible at 0 G than at +2 Gz, and that the perceived intensity and provocativeness of Coriolis stimulation decreased in 0 G and increased in +2 Gz relative to the +1 Gz baseline values. The changes in the apparent intensity of Coriolis stimulation occur virtually immediately when the background gravitatioinertial force level is varied. These findings explain why the Skylab astronauts were refractory to motion sickness during Coriolis stimulation in-flight.

Lackner, J. R.↗
DOE OSTI2026

Thorium Monosilicide, ThSi: An Experimental and Theoretical Study

The present theoretical and experimental combination study investigates the ThSi molecule in detail. Computationally, we utilized high-level multireference and coupled-cluster levels of theory conjoined with large correlation consistent basis sets to study a series of electronic and spin–orbit states of ThSi. Here, we report potential energy curves (PECs), electron configurations at equilibrium distances, spectroscopic constants, energetics, and spin–orbit coupling effects for 16 electronic states of ThSi. The studied 16 electronic states are arranged tightly within 0.9 eV, highlighting the complexity of the electronic spectrum of ThSi. The ground electronic state of ThSi is a single-reference 1 1 Σ + state that derives from the 1σ 2 2σ 2 1π 4 electronic configuration. The Ω = 0 + spin–orbit ground state of ThSi is composed of 1 1 Σ + (47%) and 13Π (44%) electronic states. Our measured bond energy (D0) of ThSi, obtained using resonant two-photon ionization (R2PI) spectroscopy is 3.146(4) eV, where the assigned error limit is given in parentheses in units of the last quoted digits. The computed D0 of ThSi (Ω = 0 + ) at the CBS-C-CCSD(T)-δT(Q)-δDK-δSO level (3.181 eV) is in good agreement with the experimental value. Our derived enthalpy of formation for ThSi, Δ f H 0K o (ThSi(g)), is 971.8(6.0) kJ/mol. Finally, we have performed density functional theory (DFT) calculations for ThSi(1 1 Σ + ) using 16 exchange correlation functionals that span multiple rungs of “Jacob’s ladder” of density functional approximation (DFA) to assess the DFT errors on D 0 , r e , and ω e of ThSi with respect to experimental and ab initio coupled-cluster values.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1994

The 20 GHz circularly polarized, high temperature superconducting microstrip antenna array

The primary goal was to design and characterize a four-element, 20 GHz, circularly polarized microstrip patch antenna fabricated from YBa2Cu3O(x) superconductor. The purpose is to support a high temperature superconductivity flight communications experiment between the space shuttle orbiter and the ACTS satellite. This study is intended to provide information into the design, construction, and feasibility of a circularly polarized superconducting 20 GHz downlink or cross-link antenna. We have demonstrated that significant gain improvements can be realized by using superconducting materials for large corporate fed array antennas. In addition, we have shown that when constructed from superconducting materials, the efficiency, and therefore the gain, of microstrip patches increases if the substrate is not so thick that the dominant loss mechanism for the patch is radiation into the surface waves of the conductor-backed substrate. We have considered two design configurations for a superconducting 20 GHz four-element circularly polarized microstrip antenna array. The first is the Huang array that uses properly oriented and phased linearly polarized microstrip patch elements to realize a circularly polarized pattern. The second is a gap-coupled array of circularly polarized elements. In this study we determined that although the Huang array operates well on low dielectric constant substrates, its performance becomes extremely sensitive to mismatches, interelement coupling, and design imperfections for substrates with high dielectric constants. For the gap-coupled microstrip array, we were able to fabricate and test circularly polarized elements and four-element arrays on LaAlO3 using sputtered copper films. These antennas were found to perform well, with relatively good circular polarization. In addition, we realized a four-element YBa2Cu3O(x) array of the same design and measured its pattern and gain relative to a room temperature copper array. The patterns were essentially the same as that for the copper array. The measured gain of the YBCO antenna was greater than that for the room temperature copper design at temperatures below 82K, reaching a value of 3.4 dB at the lowest temperatures.

Morrow, Jarrett D.↗
DOE OSTI2020

The Southern hemisphere midlatitude circulation response to rapid adjustments and sea surface temperature driven feedbacks

Rapid adjustments – the response of meteorology to external forcing while sea surface temperatures (SST) and sea ice are held fixed – can affect the midlatitude circulation and contribute to long-term forced circulation responses in climate simulations. This study examines rapid adjustments in the Southern hemisphere (SH) circulation using nine models from the Precipitation Driver and Response Model Intercomparison Project (PDRMIP), which perform fixed SST and coupled ocean experiments for five perturbations: a doubling of carbon dioxide (2xCO2), a tripling of methane (3xCH4), a five-fold increase in sulphate aerosol (5xSO4), a ten-fold increase in black carbon aerosol (10xBC) and a 2% increase in solar constant (2%Sol). In the coupled experiments, the SH eddy-driven jet shifts poleward and strengthens for forcings that produce global warming (and vice versa for 5xSO4), with the strongest response found in austral summer. In austral winter, the responses project more strongly onto a change in jet strength. For 10xBC, which induces strong shortwave absorption, the multi-model mean (MMM) rapid adjustment in DJF jet latitude is ~75% of the change in the coupled simulations. For the other forcings, which induce larger SST changes, the effect of SST-mediated feedbacks on the SH circulation is larger than the rapid adjustment. Nevertheless, for these perturbations the magnitude of the MMM jet shift due to the rapid adjustment is still around 25-33% of that in the coupled experiments. The results demonstrate the need to understand the mechanisms for rapid adjustments in the midlatitude circulation, in addition to the effect of changing SSTs.

Wood, Thomas↗
DOE OSTI2020

Optically pumped spin polarization as a probe of many-body thermalization

Disorder and many body interactions are known to impact transport and thermalization in competing ways, with the dominance of one or the other giving rise to fundamentally different dynamical phases. Here we investigate the spin diffusion dynamics of 13 C in diamond, which we dynamically polarize at room temperature via optical spin pumping of engineered color centers. We focus on low-abundance, strongly hyperfine-coupled nuclei, whose role in the polarization transport we expose through the integrated impact of variable radio-frequency excitation on the observable bulk 13 C magnetic resonance signal. Unexpectedly, we find good thermal contact throughout the nuclear spin bath, virtually independent of the hyperfine coupling strength, which we attribute to effective carbon-carbon interactions mediated by the electronic spin ensemble. In particular, observations across the full range of hyperfine couplings indicate the nuclear spin diffusion constant takes values up to two orders of magnitude greater than that expected from homo-nuclear spin couplings.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS2000

Current Status of Thin Film (Ba,Sr)TiO3 Tunable Microwave Components for RF Communications

The performance of proof-of-concept ferroelectric microwave devices has been moving steadily closer to the level needed for satellite and other rf communications applications. This paper will review recent progress at NASA Glenn in developing thin film Ba(x)Sr(1-x)TiO3 tunable micro-wave components for these applications. Phase shifters for phased array antennas, tunable filters and tunable oscillators employing microstrip and coupled microstrip configurations will be presented. Tunabilities, maximum dielectric constants, and phase shifter parameters will be discussed (e.g., coupled microstrip phase shifters with phase shift over 200 deg at 18 GHz and a figure of merit of 74.3 deg/dB). Issues of post-annealing, Mn-doping and Ba(x)Sr(1-x) TiO3 growth on sapphire and alumina substrates will be covered. The challenges of incorporating these devices into larger systems, such as yield, variability in phase shift and insertion loss, and protective coatings will also be addressed.

VanKeuls, F. W.↗
NASA NTRS2000

Current Status of Thin Film (Ba,Sr) TiO3 Tunable Microwave Components for RF Communications

The performance of proof-of-concept ferroelectric microwave devices has been moving steadily closer to the level needed for satellite and other rf communications applications. This paper will review recent progress at NASA Glenn in developing thin film Ba(x)Sr(1-x)TiO3 tunable microwave components for these applications. Phase shifters for phased array antennas, tunable filters and tunable oscillators employing microstrip and coupled microstrip configurations will be presented. Tunabilities, maximum dielectric constants, and phase shifter parameters will be discussed (e.g., coupled microstrip phase shifters with phase shift over 200 deg. at 18 GHz and a figure of merit of 74.3 deg./dB). Issues of postannealing, Mn-doping and Ba(x)Sr(1-x)TiO3 growth on sapphire and alumina substrates will be covered. The challenges of incorporating these devices into larger systems, such as yield, variability in phase shift and insertion loss, and protective coatings will also be addressed.

VanKeuls, F. W.↗