SEARCH · Engineering Papers

Results for “concentration potential”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Conductive Metallophthalocyanine Framework Films with High Carrier Mobility as Efficient Chemiresistors

Abstract The poor electrical conductivity of two‐dimensional (2D) crystalline frameworks greatly limits their utilization in optoelectronics and sensor technology. Herein, we describe a conductive metallophthalocyanine‐based NiPc‐CoTAA framework with cobalt(II) tetraaza[14]annulene linkages. The high conjugation across the whole network combined with densely stacked metallophthalocyanine units endows this material with high electrical conductivity, which can be greatly enhanced by doping with iodine. The NiPc‐CoTAA framework was also fabricated as thin films with different thicknesses from 100 to 1000 nm by the steam‐assisted conversion method. These films enabled the detection of low‐concentration gases and exhibited remarkable sensitivity and stability. This study indicates the enormous potential of metallophthalocyanine‐based conductive frameworks in advanced stand‐off chemical sensors and provides a general strategy through tailor‐make molecular design to develop sensitive and stable chemical sensors for the detection of low‐concentration gases.

Yue, Yan↗

DOE OSTI2021

Conductive Metallophthalocyanine Framework Films with High Carrier Mobility as Efficient Chemiresistors

Yue, Yan↗

DOE OSTI2021

Design of Novel Flash Ironmaking Reactors for Greatly Reduced Energy Consumption and CO2 Emissions

The development of a novel ironmaking technology based on fine iron ore concentrate in a flash reactor is summarized. The design of potential industrial reactors for flash ironmaking based on the computational fluid dynamics technique is described. Overall, this simulation work has shown that the size of the reactor used in the novel flash ironmaking technology (FIT) can be quite reasonable vis-à-vis the blast furnaces. A flash reactor of 12 m diameter and 35 m height with a single burner operating at atmospheric pressure would produce 1.0 million tons of iron per year. The height can be further reduced by either using multiple burners, preheating the feed gas, or both. The computational fluid dynamics (CFD)-based design of potential industrial reactors for flash ironmaking pointed to a number of features that should be incorporated. The flow field should be designed in such a way that a larger portion of the reactor is used for the reduction reaction but at the same time excessive collision of particles with the wall must be avoided. Further, a large diameter-to-height ratio that still allows a high reduction degree should be used from the viewpoint of decreased heat loss. This may require the incorporation of multiple burners and solid feeding ports.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Solar Thermochemical Ammonia Production (STAP) (Final Report)

Ammonia (NH 3 ) is an energy-dense chemical and a vital component of fertilizer. In addition, it is a carbon-neutral liquid fuel and a potential candidate for thermochemical energy storage for high-temperature concentrating solar power (CSP). Currently, NH 3 synthesis occurs via the Haber-Bosch process, which requires high pressures (15-25 MPa) and medium to high temperatures (400-500 °C). N 2 and H 2 are essential feedstocks for this NH 3 production process. H 2 is generally derived from methane via steam reforming; N 2 is sourced from air, after oxygen removal via combustion of hydrocarbons. Both processes consume hydrocarbons, resulting in the release of CO 2 . In addition, hydrocarbon fuels are burned to produce the heat and mechanical energy required to perform the NH 3 reaction, further increasing CO 2 emissions. Overall, the production of ammonia via the Haber-Bosch (H-B) process is responsible for up to 1.4% of the world’s carbon emissions. The development of a renewable pathway to NH 3 synthesis, which utilizes concentrated solar irradiation as a process heat instead of fossil fuels and operates under low or ambient pressure, will result in a decrease (or elimination) of greenhouse gas emissions as well as avoid the cost, complexity, and safety issues inherent in high-pressure processes. Most current efforts to “green” ammonia production involve either electrolysis or simply replacing the energy source for H-B with renewable electricity, but otherwise leaving the process intact. The effort proposed here would create a new paradigm for the synthesis of NH 3 utilizing solar-thermal heat, water, and air as feedstocks, providing a truly green method of production. The overall objective of the STAP (Solar Thermal Ammonia Production) project was to develop a solar thermochemical looping technology to produce and store nitrogen (N 2 ) from air for the subsequent production of ammonia (NH 3 ) via an advanced two-stage process. The goal is a cost-effective and energy efficient technology for the renewable N 2 production and synthesis of NH 3 from H 2 (produced from H 2 O) and air using solar-thermal energy from concentrating sunlight, under pressures an order of magnitude lower than H-B NH 3 production. Our process involves two looping cycles, which do not require catalysts and can be recycled. Over the course of the STAP project, we (1) developed and deeply characterized oxide materials for N 2 separation; (2) developed a method for the synthesis of metal nitrides, producing a series of quaternary compounds that have been heretofore unreported; (3) modeled, designed, and fabricated bench-scale tube and on-sun reactors for the N 2 production step and demonstrated the ability to separate N 2 over multiple cycles in the tube reactor; (4) designed and fabricated a bench-scale Ammonia Synthesis Reactor (ASR) and demonstrated the proof of concept of NH 3 synthesis via a novel looping process using metal nitrides over multiple cycles; and (5) completed a systems- and technoeconomic analysis showing the feasibility of ammonia production on a larger scale via the STAP process. The development of renewable, low-cost NH 3 will be of great interest to the chemicals industry, particularly agricultural sectors. The CSP industry should be both an important customer and potential end-user of this technology, as it affords the capability of synthesizing a promising thermochemical storage material on-site. Since the NH 3 synthesis step also requires H 2 , there will exist a symbiotic relationship between this technology and solar-thermochemical water-splitting applications. Green ammonia synthesis will result in the decarbonization of a hydrocarbon-intensive industry, helping to meet the Administration goal of industrial decarbonization by 2050. The resulting decrease in CO 2 and related pollutants will improve health and well-being of society, particularly for those living in the vicinity of commercial production plants.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Using concentrating-solar-power plants as economic carbon-free capacity resources

Deep decarbonization of electricity systems raises concerns about the need for generating capacity that can maintain reliable energy supply. Given this concern, we explore the ability of concentrating-solar-power plants with thermal energy storage to provide a carbon-free source of such capacity. We develop an approach to assessing the capacity contribution of concentrating-solar-power plants that considers future systems. Such considerations are important, because of potential differences in net-load patterns compared to today (e.g., due to higher renewable-energy penetrations). Using historical data spanning an 18-year period, we demonstrate that concentrating-solar-power plants with thermal energy storage can provide this necessary capacity with little impact on their financial viability. We examine the impact of myopic decisions and imperfect foresight of future system conditions on the operation of concentrating-solar-power plants and the resultant impact on their capacity contributions. We find that imperfect foresight can have limited impacts on such a use of concentrating-solar-power plants, so long as proper forecasting techniques are developed and used. Overall, our work shows that concentrating-solar-power plants with thermal energy storage may have a role to play in delivering reliable electricity supply in a decarbonized energy system.

14 SOLAR ENERGY↗

DOE OSTI2024

Detection of Anatoxins in Human Urine by Liquid Chromatography Triple Quadrupole Mass Spectrometry and ELISA

Harmful cyanobacterial blooms are becoming more common and persistent around the world. When in bloom, various cyanobacterial strains can produce anatoxins in high concentrations, which, unlike other cyanobacterial toxins, may be present in clear water. Potential human and animal exposures to anatoxins occur mainly through unintentional ingestion of contaminated algal mats and water. To address this public health threat, we developed and validated an LC-MS/MS method to detect anatoxins in human urine to confirm exposures. Pooled urine was fortified with anatoxin-a and dihydroanatoxin at concentrations from 10.0 to 500 ng/mL to create calibrators and quality control samples. Samples were diluted with isotopically labeled anatoxin and solvent prior to LC-MS/MS analysis. This method can accurately quantitate anatoxin-a with inter- and intraday accuracies ranging from 98.5 to 103% and relative standard deviations < 15%, which is within analytical guidelines for mass spectrometry methods. Additionally, this method qualitatively detects a common degradation product of anatoxin, dihydroanatoxin, above 10 ng/mL. We also evaluated a commercial anatoxin-a ELISA kit for potential diagnostic use; however, numerous false positives were detected from unexposed individual human urine samples. In conclusion, we have developed a method to detect anatoxins precisely and accurately in urine samples, addressing a public health area of concern, which can be applied to future exposure events.

urine↗

DOE OSTI2024

Stability of a Ni/NiF 2 Reference Electrode with a Metallic Membrane for Use in Molten Fluoride Salts

In this study, an experimental high-temperature fluoride salt reference electrode (RE) developed by HiFunda LLC was tested in molten FLiNaK at 550 °C. The high-temperature reference electrode (HTRE), based on the Ni/NiF 2 redox couple, was tested over a period of 13 d for short-term stability, long-term stability, and electrochemical analysis capabilities. The HTRE was tested using open circuit potentiometry (OCP), cyclic voltammetry (CV), square wave voltammetry (SWV), and electrochemical impedance spectroscopy (EIS). The HTRE reference potential was measured against changes in salt composition by increasing FeF 2 concentrations in the melt across six additions from 0 to 0.1 mol% FeF 2 . The long-term stability of the electrode was then tested over ten days at a constant composition of 0.1 mol% FeF 2 . OCP, SWV, and CV were used to calculate an average potential drift between 7–10 mV per day. Using CV and SWV, the number of electrons transferred for iron reduction and the diffusion coefficient of Fe 2+ were measured.

Electrochemistry↗

DOE OSTI2023

The impact of baryonic potentials on the gravothermal evolution of self-interacting dark matter haloes

The presence of a central baryonic potential can have a significant impact on the gravothermal evolution of self-interacting dark matter (SIDM) haloes. We extend a semi-analytical fluid model to incorporate the influence of a static baryonic potential and calibrate it using controlled N-body simulations. We construct benchmark scenarios with varying baryon concentrations and different SIDM models, including constant and velocity-dependent self-interacting cross-sections. The presence of the baryonic potential induces changes in SIDM halo properties, including central density, core size, and velocity dispersion, and it accelerates the halo’s evolution in both expansion and collapse phases. Furthermore, we observe a quasi-universality in the gravothermal evolution of SIDM haloes with the baryonic potential, resembling a previously known feature in the absence of the baryons. By appropriately rescaling the physical quantities that characterize the SIDM haloes, the evolution of all our benchmark cases exhibits remarkable similarity. In conclusion, our findings offer a framework for testing SIDM predictions using observations of galactic systems where baryons play a significant dynamical role.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2020

Poly(lactic- co -glycolic acid) Nanoparticles as Delivery Systems for the Improved Administration of Radiotherapeutic Anticancer Agents

This letter reports the development of poly(lactic- co -glycolic acid) (PLGA) nanoparticles (NPs) as delivery systems that could potentially encapsulate and improve the administration of radiotherapeutic anticancer agents. Different metal ions (Ba, Gd, and Ce) were used as surrogates of α-emitting radionuclides ( 223 Ra, 225 Ac, and 227 Th), and their encapsulation within the PLGA NPs ( D h < 300 nm) was evaluated. The initial concentration of metal ions, the metal salt (nitrate vs chloride), and the presence of chelators influenced the concentration of surrogate ions within the PLGA NPs. This letter shows the potential of PLGA NPs to encapsulate radionuclides, particularly α-emitters, for their application in nuclear medicine.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

DOE OSTI2021

Novel Geochemistry Determined from High Pressure, High Temperature Simulation Experiments of Hydraulic Fracture Test Site 2

A standard method in unconventional oil and gas production is the process of hydraulic fracturing followed by a shut-in period, during which the fracture fluid remains pressurized in the reservoir for up to three weeks before production begins. Despite this widely used process, very little is known about what occurs in the reservoir during this shut-in process. In order to properly delineate potential reservoir reactions that may occur during shut-in that would lead to corrosion and scaling events, experiments were conducted in high pressure, high temperature reactors to simulate conditions of the Wolfcamp Formation in the Delaware Basin. Experimental design allowed the assessment of the effect of proppant, microbiology, and time on the mineralogy and fluid chemistry in the reservoir. Results suggest the biggest impact on fluid chemistry and shale mineralogy during shut-in is time. Analyses demonstrate dissolution of the shale material, with maximum dissolved ions occurring after 7 days of the shut-in period. After 21 days, results suggest precipitation occurs. The Delaware Basin is demonstrated to be high in sulfate content, which further increases in the fluid due to dissolution reactions during shut-in. The pressure vessel experiments suggest there was no significant contribution to reactions from microbiology during the shut-in period. Furthermore, early production samples demonstrate a significant selection of the microorganism Caminicella, a genus of which has previously been correlated to corrosion and sulfide production. Results suggest shut-in conditions may provide high sulfate concentrations that could later be utilized by a shifted microbial community to drive potential well infrastructure failure. This is the first study to incorporate microbiology, mineralogy, and fluid chemistry to investigate the fundamental geochemical reactions that occur during shut-in and early phase production of the Delaware Downloaded from http://onepetro.org/URTECONF/proceedings-pdf/21URTC/2-21URTC/D021S032R001/2477425/urtec-2021-5219-ms.pdf/1 by Carol Worster on 28 February 2022 Basin. Results from this study can complement observations from the Hydraulic Fracture Test Site 2 observations

58 GEOSCIENCES↗

DOE OSTI2025

Colloidal Behavior of Plutonium Oxide in Concentrated Electrolyte Solutions

The Hanford Site in Washington State manages legacy high-level radioactive waste streams that display major chemistry and engineering challenges, including the high salt levels and pH values that correspond to conditions under which many classical concepts describing chemical reactivity cannot be applied. One particular challenge that needs to be tackled at Hanford is that Pu concentrations, [Pu], in the soluble phases of the tank wastes are higher than expected based on the solubility of crystalline PuO2, which is widely accepted to be caused by the formation of PuO2 colloid, consisting of nano- to submicron-sized particles (PuO2 NPs). Fundamental research underpinning the behavior of PuO2 NPs under conditions not only relevant to the Hanford tank waste but at high ionic strength in general is needed to reliably predict the chemical reactivity of PuO2 NPs and develop engineering solutions to safely and efficiently process high-level radioactive waste into forms suitable for long-term storage. In this work, we study the behavior of PuO2 NPs (particle size ~100 nm) under high ionic strength conditions by reacting it with highly concentrated (up to 5 M) salt solutions. We explore different electrolyte compositions to elucidate the impact of different anions (NO3-, Cl-, ClO4-, SO42-, C2O42-, CO32-) on the stability of PuO2 NP in the acidic and alkaline pH regime. PuO2 NP aggregation and precipitation as function electrolyte concentration is tracked by a combination of liquid scintillation counting, dynamic light scattering for determination of particle size distributions, and zeta potentials as a proxy for particle charge. At acidic pH, electrolytes containing non-coordinating anions, such as NaNO3, NaCl, and NaClO4 mostly stabilize PuO2 NPs over a large electrolyte concentration range, showing only subtle differences in their reactivity. Other electrolyte anions show a more pronounced effect on the PuO2 NP stability: SO42-, binds directly to the particles’ surface, reverses the particle charge, and precipitates the PuO2 NPs efficiently even at intermediate sulfate concentrations (>0.1 M). In contrast, C2O42- is found to lead to high [Pu] in solution, in the milli-molar range, even at mildly acidic pH (~4). Thermodynamic modeling of the dissolved Pu concentrations using PHREEQC is unable to predict the observed [Pu] in the acidic pH regime, supporting the influence of colloids in maintaining elevated [Pu]. It is noteworthy that the current thermodynamic databases do not include constants for colloidal Pu phases and cannot accurately predict many of the high ionic strength solutions relevant to this work. The mechanisms and models responsible for these observations will need further investigation in the future. At high pH values (~12), PuO2 NPs exhibits classical sol-gel chemistry, meaning that upon destabilization of the colloidal sol, for example by addition of concentrated NaOH, highly porous and viscid PuO2 coagulates are formed that consist of a three-dimensional network likely held together by physical interactions. The PuO2 NP coagulate shows no significant reversibility of the aggregation when contacted with concentrated brines; however, PuO2 NPs can be efficiently resuspended in solution by addition of diluted electrolytes, alkaline solutions containing high amounts of carbonate, or simple addition of water. Especially carbonate is shown to stabilize PuO2 NPs in solution at high pH, characterized by stable colloidal suspensions that are resistant against sedimentation during centrifugation. Thermodynamic modeling of the carbonate system was able to predict an increasing dissolved Pu concentration with increasing carbonate concentration. However, the model was profoundly sensitive to the fixed redox potential and does not include any thermodynamic constants for colloidal Pu species.

Neumann, Julia↗

DOE OSTI2022

Roadmap to Advance Heliostat Technologies for Concentrating Solar-Thermal Power

Heliostat-based concentrating solar-thermal power (CSP) systems can offer immense potential to provide low-cost, dispatchable renewable thermal and electrical energy to help achieve 100% decarbonized energy infrastructure in the United States. Heliostats are a major capital cost technology and a performance-dominating component of state-of-the-art commercial molten salt towers and Generation 3 CSP systems. In 2021, the U.S. Department of Energy (DOE) Solar Energy Technologies Office (SETO) launched the Heliostat Consortium (HelioCon), a five-year initiative to advance heliostat technologies. The HelioCon mission is threefold: (1) establish strategic core testing and modeling capabilities and infrastructure at national labs; (2) support heliostat technology development in relevant industries; and (3) serve as a central repository to integrate industry, academia, and other stakeholders for heliostat technology research, development, validation, and deployment. In this report, HelioCon presents a roadmapping study on advancing heliostat technologies, intended as a central reference for the whole CSP community.

14 SOLAR ENERGY↗

DOE OSTI2023

HelioCon: A roadmap for advanced heliostat technologies for concentrating solar power

Not Available

Zhu, Guangdong↗

DOE OSTI2020

Concentration and Recovery of Rare Earth Elements from Eastern US Coal Refuse

Recent studies funded by the US Department of energy have shown that coal and coal byproducts contain elevated contents of Rare Earth Elements (REEs), making them a potential resource for these critical materials. The approach employed in this research focused on the concentration and extraction of REEs from fine coal refuse derived from various preparation plants in the Appalachian coal basin of the United States. Initial efforts in this research focused on the identification and characterization of REEs in various fine coal refuse streams from nine distinct industrial preparation plants in Appalachia. The average REE content in these materials was determined to be approximately 200 ppm, but the REE content showed a strong correlation to the aluminum content, suggesting that the REEs are closely associated with the clay minerals present in the refuse. Given the relatively low REE concentrations, initial efforts sought to concentrate the REEs through decarbonization and dispersive liberation steps. In these tests, high-shear agitation in the presence of a polyelectrolyte, followed by sedimentation was able to isolate the REE-enriched fine clay particles from siliceous gangue minerals. Following the dispersive liberation step, all samples were found to have an REE content greater than 300 ppm, a benchmark used for many initial exploratory studies. In one case, the REE content was increased by more than 125%. Subsequent extraction tests initially utilized a direct ion-exchange leaching approach with ammonium sulfate as lixiviant. In all cases, the simple ion-exchange leaching process failed to recover significant quantities of rare earth elements, ultimately suggesting that the REEs in fine coal waste may be passivated or bound in a colloidal phase. To access this colloidal phase, several alternative approaches were evaluated, including leaching with alternative ion-exchange lixiviants, reductive leaching, gas-purged leaching, and others. The approach that showed the most promise was strong alkaline pretreatment, followed by ion-exchange leaching with ammonium sulfate at pH 4. A combination of strong alkali and high-temperatures treatment successfully liberated the REEs, converting them to a form amenable to ion-exchange leaching. The highest REE recovery achieved with this method was determined to be 39%. Lastly, bench-scale solvent extraction tests were used to further concentrate REEs in the leach solution and demonstrate that mixed rare earth concentrates can be successfully produced from fine coal refuse.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2021

Water and Solute Activities Regulate CO 2 Reduction in Gas-Diffusion Electrodes

Electrolysis of CO 2 at gas-diffusion electrodes (GDEs) has typically been limited by the supply of gas to the electrocatalyst, overshadowing the importance of the supply of water. However, at high current densities that approach 1 A cm –2 , where the electrolyte becomes highly concentrated in the catalyst layer of a GDE, the activity of water and solutes deviate from their bulk dilute solution values, potentially slowing reaction rates and changing reaction equilibrium potentials. In addition, as flow plates for the gas stream are introduced to enable larger electrodes and high single pass conversion of CO 2 to product, variations in the gas composition will become important. By drawing upon literature for the oxygen reduction reaction (ORR), here we explain how to account for these effects in future modeling and experimental work, with particular attention to accurate use of the Nernst equation for electrode potentials and the Arrhenius equation for reaction rates. Specifically, using measurements of KOH solvent and solute activity reported in literature, and assuming the second protonation of CO 2 by water as the rate-determining step, we show the Nernst equation dilute-solution approximation of the CO 2 to CO equilibrium potential to be accurate below 5 M KOH, but it has a 74 mV error when increasing the concentration up to 10 M KOH. Finally, a simple one-dimensional model of a serpentine flow-field on a GDE demonstrated that a reactor with constant pressure of 1 bar and 1 A cm –2 at the inlet had only ~0.3 A cm –2 at the outlet for a conversion in CO 2 partial pressure from 0.90 to 0.48 bar, showing the significant practical implications of this work.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

The heat transfer coefficient associated with a moving packed bed of silica particles flowing through parallel plates

Concentrating Solar Power (CSP) with thermal energy storage has the potential to be a renewable energy technology with long duration, inexpensive energy storage. Higher temperature operation increases the conversion efficiency and reduces the cost of energy storage. Several emerging CSP designs utilize particles as the solar receiver due to their high temperature stability and low cost. In some designs, the particles are also used as the thermal energy storage (TES) media. In either configuration, an energy transfer is required between the hot particles and the working fluid in the power cycle in a Particle-to-Fluid Heat Exchanger (PtFHX). Understanding the heat transfer between a moving packed bed and a stationary surface is critical to the successful design of a PtFHX. In this paper, a test facility is described in which a moving packed bed of silica sand with particle size 100–600 μm is introduced into the channel formed by two parallel plates, one of which is heated. The effective static thermal conductivity of the particles used for the test are separately measured over the entire range of test temperatures. The inlet and outlet bulk temperatures of the particle flow are measured as are the surface temperatures at several axial locations along the centerline of the plate. The result is the measurement of heat transfer coefficient as a function of temperature for several velocities. The uncertainty of the measurements is presented and the results are compared to model results found in the literature.

14 SOLAR ENERGY↗

DOE OSTI2024

Plasma potential shaping using end-electrodes in the Large Plasma Device

We perform experiments in the Large Plasma Device at the University of California, Los Angeles, studying how different end-electrode biasing schemes modify the radial potential profile in the machine. We impose biasing profiles of different polarities and gradient signs on a set of five concentric electrodes placed 12 m downstream from the plasma source. We find that imposing concave-down profiles (negative potential radial gradient) on the electrodes creates radial potential profiles halfway up the plasma column that are comparable to those imposed on the electrodes and a few electron temperature in height, regardless of the biasing polarity. On the other hand, imposing concave-up profiles (positive potential radial gradient) leads to non-monotonic radial potential profiles. This observation can be explained by the current drawn through the electrodes and the parallel plasma resistivity, highlighting their important role in controlling the rotation of plasma. Concave-down plasma potential profiles, obtained by drawing electrons on the axis, are predicted to drive azimuthal drift velocities that can approach significant fractions of the ion sound speed in the central region of the plasma column.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Multi-modal characterization of the B2 phase in the Ta-Re binary system

The energy and transportation industries demand materials that retain their mechanical property at high temperatures. Refractory complex concentrated alloys (RCCAs) with a BCC + B2 microstructure offer a potential solution, where maintaining the high temperature mechanical properties can be achieved by precipitation strengthening. This depends on the B2 phase in RCCAs being thermodynamically stable with a high solvus temperature. Recently, we predicted the high temperature stability of the B2 structure in the Ta-Re binary system, using density functional theory. Here, in this study, we provide experimental evidence for the existence of this phase for the first time, using a Ta 65 Re 35 alloy. Despite Ta-Re binary phase diagrams predicting a single-phase BCC microstructure for Ta 65 Re 35 , we show that a high Z nanoscale secondary phase appears after heat treatment at 1550 °C and 1100 °C. Scanning transmission electron microscopy (STEM) revealed that this phase has a cubic structure and is equiatomic TaRe though B2 superlattice reflections were absent in fast Fourier transforms (FFT) and diffraction patterns (DPs). DP simulations indicate that the B2 TaRe superlattice reflections are up to two orders of magnitude weaker than their fundamental reflections, making their detection challenging via electron microscopy. Neutron diffraction confirmed the second phase had a B2 structure. This study identified a previously unobserved high temperature stable B2 phase in the Ta-Re system, enabling the development of new high temperature BCC + B2 RCCAs.

36 MATERIALS SCIENCE↗