SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Priorities for research in advanced laminated fibrous composite materials are presented. Supporting evidence is presented in two bodies, including a general literature survey and a survey of aerospace composite hardware and service experience. Both surveys were undertaken during 1977-1979. Specific results and conclusions indicate that a significant portion of contemporary published research diverges from recommended priorites.
The largest known Quaternary silicic lava body in the world is Cerro Chao in north Chile, a 14-km-long coulee with a volume of at least 26 cu km. It is the largest of a group of several closely similar dacitic lavas erupted during a recent (less than 100,000 year old) magmatic episode in the Altiplano-Puna Volcanic Complex (APVC; 21-24 deg S) of the Centra; Andean Volcanic Zone. The eruption of Chao proceeded in three phases. Phase 1 was explosive and produced approximately 1 cu km of coarse, nonwelded dacitic pumice deposits and later block and ash flows that form an apron in front of the main lava body. Phase 2 was dominantly effusive and erupted approximately 22.5 cu km of magma in the form of a composite coulee covering approximately 53 sq km with a 400-m-high flow front and a small cone of poorly expanded pumice around the vent. The lava is homogeneous with rare flow banding and vesicular tops and selvages. Ogives (flow ridges) reaching heights of 30 m form prominent features on its surface. Phase 3 produced a 6-km-long, 3-km-wide flow that emanated from a collapsed dome. Ogives are subdued, and the lava is glassier than that produced in previous phases. All the Chao products are crystal-rich high-K dacites and rhyodacites with phenocrysts of plagioclase, quartz, hornblende, biotite, sphene, rare snidine, and oxides. Phenocryst contents reach 40-60 vol % (vesicle free) in the main phase 2 lavas but are lower in the phase 1 (20-25%) and phase 3 (approximately 40%) lavas. Ovoid andesitic inclusions with vesicular interiors and chilled margins up to 10 cm are found in the later stages of phase 2 and compose up to 5% of the phase 3 lava. There is little evidence for preeruptive zonation of the magma body in composition, temperature (approximately 840 C), fO2 (19(exp -11), or water content, so we propose that eruption of the Chao complex was driven by intrusion of fresh, hot andesitic magma into a crystallizing and largely homogeneous body of dacitic magma. Morphological measurements suggest that the Chao lavas had internal plastic viscosities of 10(exp 10) to 10(exp 12) Pa s, apparent viscosities of 10(exp 9) Pa s, surface viscosities of 10(exp 15) to 10(exp 24) Pa s, and a yield strength of 8 x 10(exp 5) Pa. These estimates indicate that Chao would have exhibited largely similar rheological properties to other silicic lava extrusions, notwithstanding its high phenocryst content. We suggest that Chao's anomalous size is a function of both the relatively steep local slope (20 deg to 3 deg) and the available volume of magma. The eruption duration for Chao's emplacement is thought to have been about 100 to 150 years, with maximum effusion rates of about 25 cu m/s for short periods. Four other lavas in the vicinity with volumes of approximately 5 cu km closely resemble Chao and are probably comagnetic. The suite as a whole shares a petrologic and chemical similarity with the voluminous regional Tertiary to Pleistocene ignimbrites of the APVC and may be derived from a zone of silicic magmatism that is thought to have been active since the late Tertiary. Chao and the other young lavas may represent either the waning of this system or a new episode fueled by intrusions of mafic magma.
Abstract Without a protective atmosphere, space-exposed surfaces of airless Solar System bodies gradually experience an alteration in composition, structure and optical properties through a collective process called space weathering. The return of samples from near-Earth asteroid (162173) Ryugu by Hayabusa2 provides the first opportunity for laboratory study of space-weathering signatures on the most abundant type of inner solar system body: a C-type asteroid, composed of materials largely unchanged since the formation of the Solar System. Weathered Ryugu grains show areas of surface amorphization and partial melting of phyllosilicates, in which reduction from Fe 3+ to Fe 2+ and dehydration developed. Space weathering probably contributed to dehydration by dehydroxylation of Ryugu surface phyllosilicates that had already lost interlayer water molecules and to weakening of the 2.7 µm hydroxyl (–OH) band in reflectance spectra. For C-type asteroids in general, this indicates that a weak 2.7 µm band can signify space-weathering-induced surface dehydration, rather than bulk volatile loss.
The goal is to use a variety of observational techniques and instruments, and to reduce, interpret, and synthesize ground based astronomical data concerning small bodies in the solar system, especially the asteroids, in order to study the compositions, physical characteristics, population properties, and evolution of these bodies. Progress was made in the following areas: faint asteroid taxonomy survey; photometric geodesy of Main Belt asteroids; and Main Belt and Near Earth Asteroids synthesis studies.
One of the most fundamental pieces of information about any planetary body is the elemental and mineralogical composition of its surface materials. We are developing an instrument to obtain such data at ranges of up to several hundreds of meters using the technique of Laser-Induced Breakdown Spectroscopy (LIBS). We envision our instrument being used from a spacecraft in close rendezvous with small bodies such as comets and asteroids, or deployed on surface-rover vehicles on large bodies such as Mars and the Moon. The elemental analysis is based on atomic emission spectroscopy of a laser-induced plasma or spark. A pulsed, diode pumped Nd:YAG laser of several hundred millijoules optical energy is used to vaporize and electronically excite the constituent elements of a rock surface remotely located from the laser. Light emitted from the excited plasma is collected and introduced to the entrance slit of a small grating spectrometer. The spectrally dispersed spark light is detected with either a linear photo diode array or area CCD array. When the latter detector is used, the optical and spectrometer components of the LIBS instrument can also be used in a passive imaging mode to collect and integrate reflected sunlight from the same rock surface. Absorption spectral analysis of this reflected light gives mineralogical information that provides a remote geochemical characterization of the rock surface. We performed laboratory calibrations in air and in vacuum on standard rock powders to quantify the LIBS analysis. We performed preliminary field tests using commercially available components to demonstrate remote LIBS analysis of terrestrial rock surfaces at ranges of over 25 m, and we have demonstrated compatibility with a six-wheeled Russian robotic rover vehicle. Based on these results, we believe that all major and most minor elements expected on planetary surfaces can be measured with absolute accuracy of 10-15 percent and much higher relative accuracy. We have performed preliminary systems analysis of a LIBS instrument to evaluate probable mass and power requirements; results of this analysis are summarized.
A nanovector multistage system has been created to overcome or bypass sequential barriers within the human body, in order to deliver a therapeutic or imaging agent to a specific location. This innovation consists of a composition that includes two or more stages of particles, such that smaller, later-stage particles are contained in the larger, early-stage particles. An active agent, such as a therapeutic agent or imaging agent, is preferentially delivered and/or localized to a particular target site in the body of a subject. The multistage composition overcomes multiple biological barriers in the body. The multistage composition also allows for simultaneous delivery and localization at the same or different target sites of multiple active agents.
This report documents preliminary design trades conducted under NASA contracts NAS1 18889 (Advanced Technology Composite Aircraft Structures, ATCAS) and NAS1-19349 (Task 3, Pathfinder Shell Design) for a subsonic wide body commercial aircraft fuselage side panel section utilizing composite materials. Included in this effort were (1) development of two complete design concepts, (2) generation of cost and weight estimates, (3) identification of technical issues and potential design enhancements, and (4) selection of a single design to be further developed. The first design concept featured an open-section stringer stiffened skin configuration while the second was based on honeycomb core sandwich construction. The trade study cost and weight results were generated from comprehensive assessment of each structural component comprising the fuselage side panel section from detail fabrication through airplane final assembly. Results were obtained in three phases: (1) for the baseline designs, (2) after global optimization of the designs, and (3) the results anticipated after detailed design optimization. A critical assessment of both designs was performed to determine the risk associated with each concept, that is the relative probability of achieving the cost and weight projections. Seven critical technical issues were identified as the first step towards side panel detailed design optimization.
Collectively, acapulcoites and lodranites form a clan of primitive achondrites generally thought to have originated from the same parent body on the basis of similarities in petrology, mineral compositions, bulk compositions, cosmic ray exposure ages and oxygen isotope compositions, although considerable variation in some of these parameters has shown that the parent body was not entirely uniform. The presence of relict chondrules in several acapulcoites indicates that all were likely derived from chondrite-like precursor materials. The transition from acapulcoite to lodranite is gradual and corresponds to increasing metamorphic grade. Lodranites are generally coarser grained, but petrographic distinction between the two groups can also be made by modal abundances of troilite and plagioclase. Depletion of both these phases and incompatible lithophile trace elements in lodranites is consistent with their restitic origin formed by greater than 10% extraction of basaltic melt. Magnesian lodranites (e.g. Gibson, GRA 95209, Y-75274, Y-8002), some of which might also be considered transitional acapulcoites, have mineral and chemical compositions consistent with derivation by thermal metamorphism and partial melt extraction from acapulcoites, as would seem logical if samples represented different grades of metamorphism along a linear evolution trend. Ferromagnesian silicates in these lodranites tend to be displaced toward lower fe# (opx fe# 4-6) than the distribution observed in acapulcoites (opx fe# 6-11). A subset of lodranites, termed ferroan lodranites (e.g. FRO 90011, LEW 88280, Lodran, MAC 88177, Y-74357, Y- 791491/Y-791493), have ferromagnesian silicate minerals that are too Fe-rich (fe#>10) to have formed as simple restites from any known acapulcoite. Like silicates, metal-sulfide systematics of the ferroan lodranites are also inconsistent with a simple restitic origin. Logically, restitic lodranites should have been depleted in FeS during extraction of partial melts, since melting of the metal-sulfide system initiates at lower temperatures than melting of silicates. Yet, puzzingly, ferroan lodranites contain significant quantities (1.9-5.3 modal%) of troilite, indicating either (1) metal sulfide partial melts were retained during basaltic melt extraction or (2) later infusion of metal sulfide melts has occurred. In this study, we use trace siderophile elements in metals to assess the relative importance of each in creating the observed troilite enrichment.
This paper describes the Probing In situ with Neutron and Gamma rays (PING) instrument, that can measure the subsurface elemental composition in situ for any rocky body in the solar system without the need for digging into the surface. PING consists of a Pulsed Neutron Generator (PNG), a gamma ray spectrometer and neutron detectors. Subsurface elements are stimulated by high-energy neutrons to emit gamma rays at characteristic energies. This paper will show how the detection of these gamma rays results in a measurement of elemental composition. Examples of the basalt to granite ratios for aluminum and silicon abundance are provided.
Solid-lubricant-containing compositions can be of value as films and solid bodies for bearing and seal surfaces in low-temperature liquefied gases. An experimental composition including polytetrafluoroethylene (PTFE), an epoxy resin, and lithium-alumina-silicate was studied in friction, wear, and endurance experiments in liquid nitrogen (−320 F). This composition was formulated to approximate the thermal expansion of metals used in cryogenic systems. Hemisphere (3/6-in. radius) rider specimens were used and in most experiments the load was 1000 g. Films (0.005-in. thick) on disk specimens gave good endurance life, low rider wear, and desirable friction (f = 0.02 to 0.07). They functioned at a higher sliding velocity (no failure at 16, 000 ft/min) with copper rider specimens than with stainless steel riders (failure at 9000 ft/min). Solid rider material of the experimental composition had good friction and wear properties at sliding velocities above 4000 ft/min. It is important to use the experimental composition with mating materials having good thermal conductivity.
Angrites are an enigmatic group of achondrites, that constitute the largest group of basalts not affiliated with the Moon, Mars or Vesta (HEDs). Chemically, angrites are exceptionally refractory element- enriched (e.g., Al, Ca) and volatile element-depleted (e.g., Na and K) achondrites. Highly volatile siderophile and chalcophile elements (Zn, Ge and Se) may be less depleted than alkalis and Ga taken to imply a fractionation of plagiophile elements. Core formation on the angrite parent body (APB) is not well understood due to the dearth of moderately siderophile element (Ga, Ge, Mo, Sb, W) data for angrites, with the exception of Ni and Co [2]. In particular, there are no data for Mo abundances of angrites, while Sb and W abundances are reported for only 3 angrites, and have not always been determined on the same sample. The recent increase in angrite numbers (13) has greatly increased our knowledge of the compositional diversity of the angrite parent body (APB). In this study, we report new Co, Ni, Ga, Mo, Sb and W abundances for angrites by laser ablation inductively coupled plasma mass spectrometry (ICP-MS) in order to place constraints on core formation of the APB.
Space weathering is an important process that affects the surfaces of airless bodies, such as (101955) Bennu. The consequences of this process include physical and chemical changes to materials on the surface, which in turn change spectral characteristics, especially in the visible to near infrared wavelengths. These spectral changes are not the same across airless bodies because the changes are dependent on the composition and mineralogy of the surface and even location within the Solar System. The main space weathering products responsible for these spectral changes are submicroscopic particles, which consist of two types, nanophase and microphase particles, and affect visible to near-infrared reflectance spectra differently. Nanophase particles are particles <33 nm in size and occur in agglutinates and within glassy patinas around regolith particles. In contrast, microphase particles are >33 nm in size and are present only within agglutinates. These spectral differences are best illustrated by lunar samples. In lunar soils, the nanophase and microphase particles consist of metallic iron. With increasing abundance of nanophase iron particles in a regolith, its spectrum exhibits a lower overall reflectance in the visible to near infrared, weakened absorption bands, and a reddened continuum slope. In contrast, an increasing abundance of microphase iron only causes decreases in reflectance and not reddening. Because of the spectral differences introduced by these two types of particles, it is possible to model the nanophase and microphase particle abundances of a surface through the radiative transfer technique. Beyond the Moon, the composition of the nanophase and microphase particles can include other phases because the mineralogy of the surfaces of other planetary bodies is different. For example, the nanophase and microphase particles may consist of amorphous carbon (Mercury) and sulfides (Itokawa). The mineralogy of Bennu is consistent with carbonaceous chondrites. From a number of space weathering experiments on CM chondrites, the likely nanophase and microphase mineral phases on Bennu includes iron, magnetite, and sulfides (i.e., pentlandite and troilite). The goal of this work is to input the predicted nanophase and microphase compositions for Bennu into the radiative transfer technique. Next, we use this technique to model the OSIRIS-REx Visible Infrared Spectrometer (OVIRS) so that we can model the nanophase and microphase particle abundances across the surface. This will result in space weathering maps of the surface of Bennu, which are useful for understanding the degree of space weathering across the surface and its relationship to various regions and geological features.
Masses of meteors calculated from radiation, velocity, composition, and structural measurements
The abundance of H in planetary building blocks is of fundamental importance for constraining the evolution of the terrestrial planets. It is commonly assumed that chondrites are the principal sources of Earth’s H; however, recent studies have suggested that primitive achondrites and achondrites may retain a small complement of H. There are few constraints on the H budgets of primitive achondrites, which represent the transition from unmelted to melted planetesimals, but prior work suggests that bulk parent body H contents are several orders of magnitude lower than typical chondritic values. Therefore, to provide further constraints on H retention during the transition from unmelted to melted planetesimals, we have measured the H contents of olivine, orthopyroxene, clinopyroxene, and plagioclase from a suite of acapulcoite-lodranite clan meteorites. Acapulcoite-lodranite clan meteorites represent the “prototypical” primitive achondrite parent body and have bulk major element compositions more akin to the Earth than previously studied primitive achondrites (e.g., the ureilites). We find that the H 2 O contents of olivine (∼5–12 µg/g H 2 O), orthopyroxene (∼3–10 µg/g H 2 O), and clinopyroxene (∼5–8 µg/g H 2 O) are broadly similar, while plagioclase (∼2.5–5 µg/g H 2 O) tends to be offset to lower values. Using a simple, single-stage batch-melting model, we calculate a preferred maximum acapulcoite-lodranite parent body H 2 O content of 38 µg/g, which is similar to other estimates for primitive achondritic and achondritic parent bodies. Furthermore, assuming chondrite-like precursor materials, our data are consistent with efficient loss of H prior to or during the onset of melting of early-formed planetesimals. This requires that Earth’s H-budget was dominated by building blocks that underwent minimal thermal processing.
A wealth of scientific knowledge regarding the composition and evolution of the solar system can be gained through reconnaissance missions to primitive solar system bodies. This paper presents analysis of a baseline navigation strategy designed to address the unique challenges of primitive body navigation. Linear covariance and Monte Carlo error analysis was performed on a baseline navigation strategy using simulated data from a· design reference mission (DRM). The objective of the DRM is to approach, rendezvous, and maintain a stable orbit about the near-Earth asteroid 4660 Nereus. The outlined navigation strategy and resulting analyses, however, are not necessarily limited to this specific target asteroid as they may he applicable to a diverse range of mission scenarios. The baseline navigation strategy included simulated data from Deep Space Network (DSN) radiometric tracking and optical image processing (OpNav). Results from the linear covariance and Monte Carlo analyses suggest the DRM navigation strategy is sufficient to approach and perform proximity operations in the vicinity of the target asteroid with meter-level accuracy.
The main-belt asteroid 4 Vesta is the putative parent body of the howardite, eucrite, and diogenite (HED) meteorites. Because these achondrites have similar petrology, geochemistry, chronology, and O-isotope compositions, it is thought that most HEDs originated from a single parent body. The connection to Vesta is supported by a close spectroscopic match between Vesta and the HEDs and a credible mechanism for their delivery to Earth. Studies of the HEDs show that Vesta underwent igneous differentiation, forming a Fe-rich core, ultramafic mantle, and basaltic crust. Here we present the results of peak analyses applied to a gamma ray difference spectrum to determine the absolute abundances of K and Th. Data are compared to meteorite whole-rock compositions and other inner solar system bodies. The results, while preliminary, represent our present best estimates for these elements. Because the element signatures are near detection limits and not fully resolved, further analysis (e.g. using spectral unmixing) will be required for improved accuracy and to characterize systematic errors.
The ternary-arsenide compound BaCo 2 As 2 was previously proposed to be in proximity to a quantum-critical point where long-range ferromagnetic (FM) order is suppressed by quantum fluctuations. In this paper we report the effect of Ir substitutions for Co on the magnetic and thermal properties of Ba(Co 1-x Ir x ) 2 As 2 (0 ≤ x ≤ 0.25) single crystals. These compositions all crystallize in an uncollapsed body-centered-tetragonal ThCr 2 Si 2 structure with space group I4/mmm. Magnetic susceptibility measurements reveal clear signatures of short-range FM ordering for x ≥ 0.11 below a nearly composition-independent characteristic temperature T cl ≈ 13 K. The small variation of T cl with x, thermomagnetic irreversibility between zero-field-cooled and field-cooled magnetic susceptibility versus T, the occurrence of hysteresis in magnetization versus field isotherms at low field and temperature, and very small spontaneous and remanent magnetizations <0.01 μ B /f.u. together indicate that the FM response arises from short-range FM ordering of FM spin clusters as previously inferred to occur in Ca(Co 1–x Ir x ) 2–y As 2 . Heat-capacity Cp(T) data do not exhibit any clear feature around Tcl, consistent with the very small moments of the FM clusters. The Cp(T) in the paramagnetic temperature regime 25–300 K is well described by the sum of a Sommerfeld electronic contribution and Debye and Einstein lattice contributions where the latter lattice contribution suggests the presence of low-frequency optic modes associated with the heavy Ba atoms in the crystals.
The close encounters of the Pluto–Charon system and the Kuiper Belt object Arrokoth (formerly 2014 MU 69 ) by NASA’s New Horizons spacecraft in 2015 and 2019, respectively, have given new perspectives on the most distant planetary bodies yet explored. These bodies are key indicators of the composition, chemistry, and dynamics of the outer regions of the Solar System’s nascent environment. Pluto and Charon reveal characteristics of the largest Kuiper Belt objects formed in the dynamically evolving solar nebula inward of ~30 AU, while the much smaller Arrokoth is a largely undisturbed relic of accretion at ~45 AU. The surfaces of Pluto and Charon are covered with volatile and refractory ices and organic components, and have been shaped by geological activity. On Pluto, N 2 , CO and CH 4 are exchanged between the atmosphere and surface as gaseous and condensed phases on diurnal, seasonal and longer timescales, while Charon’s surface is primarily inert H 2 O ice with an ammoniated component and a polar region colored with a macromolecular organic deposit. Arrokoth is revealed as a fused binary body in a relatively benign space environment where it originated and has remained for the age of the Solar System. Its surface is a mix of CH 3 OH ice, a red-orange pigment of presumed complex organic material, and possibly other undetected components.