SEARCH · Engineering Papers

Results for “attack modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

All sources NASA NTRS DOE OSTI

NASA NTRS1990

The effect of turbulence models on the numerical prediction of the flowfield about a prolate spheroid at high angle of attack

The F3D thin-layer Navier-Stokes code presently used to numerically investigate the three-dimensional separated flow about a prolate spheroid at high incidence analyzes the effect of different turbulence models on the flowfield solution and the characteristics of the predicted flow. The Johnson-King (1984) model is applied in order to evaluate the importance of modeling nonequilibrium effects in predicting flow about a slender body at high incidence; the computations in question are for steady-state, fully turbulent flow. Insight is gained into the effects of turbulence models on flow characteristics, and model effects on the accurate prediction of highly separated and vortical flows about a slender body are demonstrated.

Gee, Ken↗

NASA NTRS1990

Development of non-conventional control methods for high angle of attack flight using vortex manipulation

Methods of manipulating the forebody vortices on a generic fighter model to produce controlled yawing moments at high angles of attack were investigated. Forces and moments were measured on the complete configuration and on the isolated forebody. Two schemes for vortex control on the forebody were evaluated: individually-controlled tip strakes and individually-controlled blowing ports. The effectiveness of the forebody strakes in controlling forebody side forces was strongly dependent on the size and location of the strakes. A yawing moment can be produced by deploying the forebody strakes asymmetrically, or can be eliminated by deploying the strakes symmetrically. The most effective strake position was found to be near the primary separation point, between 105 and 120 deg from windward. Blowing on the surface of the model was also shown to have a strong effect on the yawing moment. Blowing either forward or aft tangential to the surface appears to be more effective than blowing normal to the surface. The most effective method to control the yawing moment on the forebody was to minimize the natural asymmetry with a pair of small symmetrically mounted tip strakes and to perturb the vortex system away from the symmetric condition with asymmetric blowing.

Malcolm, Gerald N.↗

NASA NTRS1959

The Effect of Moment of Area Rule Modifications on the Drag, Lift and Pitching Moment Characteristics of an Unswept Aspect Ratio 6 Wing and Body Combination

An experimental investigation was conducted to determine the effect of moment-of-area-rule modifications on the drag, lift, and pitching-moment characteristics of a wing-body combination with a relatively high aspect-ratio unswept wing. The basic configuration consisted of an aspect-ratio-6 wing with a sharp leading edge and a thickness ratio of 0.06 mounted on a cut-off Sears-Haack body. The model with full moment-of-area-rule modifications had four contoured pods mounted on the wing and indentations in the body to improve the longitudinal distributions of area and moments of area. Also investigated were modifications employing pods and indentations that were only half the size of the full modifications and modifications with partial body indentations. The models were tested at angles of attack from -2 deg to +12 deg at Mach numbers from 0.6 to 1.4. In general, the moment-of-area-rule modifications had a large effect on the drag characteristics of the models but only a small effect on their lift and pitching-moment characteristics. The modifications provided substantial reductions in the zero-lift drag at transonic and low supersonic speeds, but at subsonic speeds the drag was increased. Near Mach number 1.0, the model with full modification provided the greatest reduction in drag, but at the highest test Mach numbers the half modification gave the largest drag reduction. In general, the percent reductions of zero- lift drag obtained with the aspect-ratio-6 wing were as great or greater than those previously obtained with aspect-ratio-3 wings. The effect of the modifications on the drag due to lift was small except at Mach num- bers below 0.9 where the modified models had higher drag-rise factors. Above Mach number 0.9, the modified models had higher lift-drag ratios than the basic model. The modified models also had higher lift curve slopes and generally were slightly more stable than the basic configuration.

Dickey, Robert R.↗

NASA NTRS1972

Ascent heat transfer rate distribution on the North American Rockwell delta wing orbiter and the General Dynamics/Convair booster at a Mach number of 8 (mated)

A wind tunnel test program to determine aerodynamic interference heating on the North American Rockwell orbiter mated with the General Dynamics Convair booster is discussed. The tests were conducted at the Arnold Engineering Development Center (AEDC) in Tunnel B of the von Karman Gas Dynamics Facility (VKF). The test period was June 1971. Heat-transfer rates were determined by the phase-change paint technique on 0.013-scale Stycast models using Tempilaq as the surface temperature indicator. The nominal test conditions were: Mach 8, free-stream unit length Reynolds numbers of 1.25 x one million and 2.55 x one million angles of attack of -5, 0, +5 deg. Model details, test conditions, phase-change paint photographs and reduced heat-transfer coefficients are presented.

Matthews, R. K.↗

NASA NTRSDate not supplied

A Reynolds-Averaged Navier-Stokes Perspective for the High Lift Common Research Model Using the LAVA Framework

An in-depth assessment of the High Lift-Common Research Model (HL-CRM) aerodynamic performance is made using a Reynolds-Averaged Navier-Stokes (RANS) methodology. Results presented here were produced in support of the 4th AIAA High Lift Prediction Workshop(HLPW-4), with additional simulation results and analysis used to support findings from the workshop. Mesh resolution, RANS closure models, and tunnel effects were among the sources of simulation sensitivity addressed, all in the pursuit of evaluating best-practice simulation methods for complex high-lift configurations. In general, free-air simulations using RANS yield accurate predictions of integrated loads in the pre-stall regime for the HL-CRM, while strong sensitivity to simulation method is observed near CLmax. Additionally, a study assessing changes in aerodynamic performance due to flap deflection angle indicated strong sensitivity to turbulence model closure and mesh resolution, particularly at the highest deflection setting. Several available corrections for the Spalart-Allmaras (SA) turbulence model were tested and generally introduced more error relative to the experiment in comparison to the baseline SA closure model. The Standard Menter Baseline Two-Equation (k-ωBSL) turbulence model was also explored, which arguably yielded results highly consistent with experiment, but at a substantially higher computational cost. Therefore, as a compromise between computational cost and accuracy, the baseline SA closure model was selected for additional HL-CRM studies that assess alternative solution methods. These strategies include “warm start” approaches, which initialize the simulation from a previously converged solution at a nearby angle of attack, unsteady calculations, and simulations that model the experimental wind tunnel. Results from these studies would reinforce the shortcomings of RANS in predicting aircraft performance at high-lift conditions, namely at high-αand highly loaded flap conditions, while also answering questions about appropriate modeling techniques to minimize the errors associated with RANS where possible

TTT↗

NASA NTRS2004

Effects of Angle of Attack and Velocity on Trailing Edge Noise

Trailing edge (TE) noise measurements for a NACA 63-215 airfoil model are presented, providing benchmark experimental data for a cambered airfoil. The effects of flow Mach number and angle of attack of the airfoil model with different TE bluntnesses are shown. Far-field noise spectra and directivity are obtained using a directional microphone array. Standard and diagonal removal beamforming techniques are evaluated employing tailored weighting functions for quantitatively accounting for the distributed line character of TE noise. Diagonal removal processing is used for the primary database as it successfully removes noise contaminates. Some TE noise predictions are reported to help interpret the data, with respect to flow speed, angle of attack, and TE bluntness on spectral shape and peak levels. Important findings include the validation of a TE noise directivity function for different airfoil angles of attack and the demonstration of the importance of the directivity function s convective amplification terms.

Hutcheson, Florence V.↗

NASA NTRS2006

Effects of Angle of Attack and Velocity on Trailing Edge Noise

Hutcheson, Florence V.↗

NASA NTRS1993

A study of roll attractor and wing rock of delta wings at high angles of attack

Wing rock is a high angle of attack dynamic phenomenon of limited cycle motion predominantly in roll. The wing rock is one of the limitations to combat effectiveness of the fighter aircraft. Roll Attractor is the steady state or equilibrium trim angle (phi(sub trim)) attained by the free-to-roll model, held at some angle of attack, and released form rest at a given initial roll (bank) angle (phi(sub O)). Multiple roll attractors are attained at different trim angles depending on initial roll angle. The test facility (Vigyan's low speed wind tunnel) and experimental work is presented here along with mathematical modelling of roll attractor phenomenon and analysis and comparison of predictions with experimental data.

Niranjana, T.↗

NASA NTRS1982

Rotary balance data for a typical single-engine general aviation design for an angle-of-attack range of 8 deg to 90 deg. 2: Influence of horizontal tail location for Model D

The influence of horizontal tail location on the rotational flow aerodynamics is discussed for a 1/6-scale general aviation airplane model. The model was tested using various horizontal tail positions, with both a high and a low-wing location and for each of two body lengths. Data were measured, using a rotary balance, over an angle-of-attack range of 8 to 90 deg, and for clockwise and counter-clockwise rotations covering an Omega b/2V range of 0 to 0.9.

Barnhart, B.↗

NASA NTRS1989

Application of variable-gain output feedback for high-alpha control

This paper describes a variable-gain optimal discrete output-feedback design approach that is applied to a nonlinear flight regime covering a wide angle-of-attack range that includes stall and poststall. The paper includes brief descriptions of the variable-gain formulation, the discrete-control structure and flight equations used to apply the design approach, and the high performance airplane model used in the application. Both linear and nonlinear analyses are shown for a longitudinal four-model design case with angles of attack of 5, 15, 35, and 60 deg.

Ostroff, Aaron J.↗

NASA NTRS1976

Application of a helicopter mathematical model to the Langley differential maneuvering simulator for use in a helicopter/fighter evasive maneuver study

A real time simulation study was conducted using a differential maneuvering simulator to determine and evaluate helicopter evasive maneuvers when attacked by fighter aircraft. A general helicopter mathematical model was modified to represent an H-53 helicopter. The helicopter model was compared to H-53 flight test data to determine any differences between the simulated and actual vehicles. The simulated helicopter was also subjectively validated by participating pilots. Two fighter mathematical models validated in previous studies were utilized for the attacking aircraft. The results of this simulation study have been verified in a flight test program conducted by the U. S. Air Force and were found to closely match the flight results.

Houck, J. A.↗

NASA NTRS1998

Recent Dynamic Measurements and Considerations for Aerodynamic Modeling of Fighter Airplane Configurations

As airplane designs have trended toward the expansion of flight envelopes into the high angle of attack and high angular rate regimes, concerns regarding modeling the complex unsteady aerodynamics for simulation have arisen. Most current modeling methods still rely on traditional body axis damping coefficients that are measured using techniques which were intended for relatively benign flight conditions. This paper presents recent wind tunnel results obtained during large-amplitude pitch, roll and yaw testing of several fighter airplane configurations. A review of the similitude requirements for applying sub-scale test results to full-scale conditions is presented. Data is then shown to be a strong function of Strouhal number - both the traditional damping terms, but also the associated static stability terms. Additionally, large effects of sideslip are seen in the damping parameter that should be included in simulation math models. Finally, an example of the inclusion of frequency effects on the data in a simulation is shown.

Brandon, Jay M.↗

NASA NTRS1955

Initial experimental investigation of the aerodynamic load on the wing of a model caused by a blast-induced gust that increases the angle of attack into the stall region

Explore the source record for details and available documents.

Pierce, Harold B↗

NASA NTRS1993

Experimental apparatus for optimization of flap position for a three-element airfoil model

It is proposed to design and build a wind tunnel model comprising a Douglas Aircraft Company three-element high-lift airfoil with internal actuators to move the flap vertically and horizontally under computer control. The model will be used to find the optimum flap location for a fixed angle of attack, slat position and flap deflection angle. The model will span the full tunnel width and lift will be measured by integration of pressure readings taken from midspan taps. It is proposed to conduct experiments in the NASA Langley EFPB 2' x 3' low speed wind tunnel. This report serves as a project overview and a review of work completed to date through funding by the 1993 NASA/ASEE Summer Faculty Fellowship Program.

Landman, Drew↗

NASA NTRS1999

Adaptive Suction and Blowing for Twin-Tail Buffet Control

Adaptive active flow control for twin-tail buffet alleviation is investigated. The concept behind this technique is to place control ports on the tail outer and inner surfaces with flow suction or blowing applied through these ports in order to minimize the pressure difference across the tail. The suction or blowing volume flow rate from each port is proportional to the pressure difference across the tail at this location. A parametric study of the effects of the number and location of these ports on the buffet response is carried out. The computational model consists of a sharp-edged delta wing of aspect ratio one and swept-back flexible twin tail with taper ratio of 0.23. This complex multidisciplinary problem is solved sequentially using three sets of equations for the fluid flow, aeroelastic response and grid deformation, using a dynamic multi-block grid structure. The computational model is pitched at 30 deg angle of attack. The freestream Mach number and Reynolds number are 0.3 and 1.25 million, respectively. The model is investigated for the inboard position of the twin tails, which corresponds to a separation distance between the twin tails of 33% of the wing span. Comparison of the time history and power spectral density responses of the tails for various distributions of the control ports are presented and discussed.

Kandil, Osama A.↗

NASA NTRS1986

Pressure distributions obtained on a 0.10-scale model of the space shuttle Orbiter's forebody in the AEDC 16T propulsion wind tunnel

Pressure distribution test data obtained on a 0.10-scale model of the forward fuselage of the Space Shuttle Orbiter are presented without analysis. The tests were completed in the AEDC 16T Propulsion Wind Tunnel. The 0.10-scale model was tested at angles of attack from -2 deg to 18 deg and angles of side slip from -6 to 6 deg at Mach numbers from 0.25 to 1/5 deg. The tests were conducted in support of the development of the Shuttle Entry Air Data System (SEADS). In addition to modeling the 20 SEADS orifices, the wind-tunnel model was also instrumented with orifices to match Development Flight Instrumentation (DFI) port locations that existed on the Space Shuttle Orbiter Columbia (OV-102) during the Orbiter Flight Test program. This DFI simulation has provided a means of comparisons between reentry flight pressure data and wind-tunnel and computational data.

Siemers, P. M., III↗

NASA NTRS2001

X-38 Experimental Aeroheating at Mach 10

This report provides an update of the hypersonic aerothermodynamic wind tunnel test program conducted at the NASA Langley Research Center in support of the X-38 program. Global surface heat transfer distributions were measured on 0.0177 and 0.0236 scale models of the proposed X-38 configuration at Mach 10 in air. The parametrics that were investigated primarily include freestream unit Reynolds numbers of 0.6 to 2.2 million per foot and body flap deflections of 15, 20, and 25 deg for an angle-of-attack of 40 deg. The model-scale variance was tested to obtain laminar, transitional, and turbulent heating levels on the defected bodyflaps. In addition, a limited investigation of forced boundary layer transition through the use of discrete roughness elements was performed. Comparisons of the present experimental results to computational predictions and previous experimental data were conducted Laminar, transitional, and turbulent heating levels were observed on the deflected body flap, which compared favorably to the computational results and to the predicted heating based on the flight aerothermodynamic database.

Berry, Scott A.↗

NASA NTRS1976

Subsonic and transonic dynamic stability characteristics of the space shuttle launch vehicle

An investigation has been conducted to determine the subsonic and transonic dynamic stability characteristics of a 0.015 scale model of the space shuttle launch vehicle. These tests were conducted in the Langley 8-foot transonic pressure tunnel over a Mach number range from 0.3 to 1.2. Forced oscillation equipment was used to determine the damping characteristics of several configurations about all three axes. The test results show that the model exhibited positive damping in pitch except at the highest Mach number (1.2) where there was a region of negative damping at 2 deg angle of attack. The yawing oscillation tests show that the model exhibited nonlinearities and negative damping at Mach numbers of 0.3 and 0.6. The model exhibited positive roll damping throughout the test angle of attack and Mach range.

Freeman, D. C., Jr.↗