Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Soft materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Ensemble Monte Carlo calculation of the hole initiated impact ionization rate in bulk GaAs and silicon using a k-dependent, numerical transition rate formulation

The hole initiated impact ionization rate in bulk silicon and GaAs is calculated using a numerical formulation of the impact ionization transition rate incorporated into an ensemble Monte Carlo simulation. The transition rate is calculated from Fermi's golden rule using a two-body screened Coulomb interaction including a wavevector dependent dielectric function. It is found that the effective threshold for hole initiated ionization is relatively soft in both materials, that the split-off band dominates the ionization process in GaAs. and that no clear dominance by any one band is observed in silicon, though the rate out of the light hole band is greatest.

Oguzman, Ismail H.↗
NASA NTRS2001

The Effect of Journal Roughness and Foil Coatings on the Performance of Heavily Loaded Foil Air Bearings

Foil air bearing load capacity tests were conducted to investigate if a solid lubricant coating applied to the surface of the bearing's top foil can function as a break-in coating. Two foil coating materials, a conventional soft polymer film (polyimide) and a hard ceramic (alumina), were independently evaluated against as-ground and worn (run-in) journals coated with NASA PS304, a high-temperature solid lubricant composite coating. The foil coatings were evaluated at journal rotational speeds of 30,000 rpm and at 25 C. Tests were also performed on a foil bearing with a bare (uncoated) nickel-based superalloy top foil to establish a baseline for comparison. The test results indicate that the presence of a top foil solid lubricant coating is effective at increasing the load capacity performance of the foil bearing. Compared to the uncoated baseline, the addition of the soft polymer coating on the top foil increased the bearing load coefficient by 120% when operating against an as-ground journal surface and 85 percent against a run-in journal surface. The alumina coating increased the load coefficient by 40% against the as-ground journal but did not have any affect when the bearing was operated with the run-in journal. The results suggest that the addition of solid lubricant films provide added lubrication when the air film is marginal indicating that as the load capacity is approached foil air bearings transition from hydrodynamic to mixed and boundary lubrication.

Radil, Kevin C.↗
NASA NTRS2007

Overview of the Mars Science Laboratory Parachute Decelerator Subsystem

In 2010 the Mars Science Laboratory (MSL) mission will deliver NASA's largest and most capable rover to the surface of Mars. MSL will explore previously unattainable landing sites due to the implementation of a high precision Entry, Descent, and Landing (EDL) system. The parachute decelerator subsystem (PDS) is an integral prat of the EDL system, providing a mass and volume efficient some of aerodynamic drag to decelerate the entry vehicle from Mach 2 to subsonic speeds prior to final propulsive descent to the sutface. The PDS for MSL is a mortar deployed 19.7m Viking type Disk-Gap-Band (DGB) parachute; chosen to meet the EDL timeline requirements and to utilize the heritage parachute systems from Viking, Mars Pathfinder, Mars Exploration Rover, and Phoenix NASA Mars Lander Programs. The preliminary design of the parachute soft goods including materials selection, stress analysis, fabrication approach, and development testing will be discussed. The preliminary design of mortar deployment system including mortar system sizing and performance predictions, gas generator design, and development mortar testing will also be presented.

Entry, Descent, and Landing (EDL)↗
DOE OSTI2026

Charge Transport in Solvated Donor–Acceptor Functionalized Peptoids: Molecular Dynamics and Rate Theory

Scalable solar-energy conversion requires photoactive materials that combine the efficiency of natural photosynthetic systems with the stability and processability needed for practical applications. Achieving reliable charge transport in soft, self-assembled organic materials remains challenging, as structural fluctuations and environmental effects strongly influence charge-transfer (CT) rates. Here, we present a broadly applicable computational framework for evaluating CT rates in the condensed phase, combining Fermi’s golden rule rate theory with inputs from all-atom molecular dynamics (MD) simulations and first-principles electronic-structure calculations. The approach does not rely on system-specific parametrization and is applicable to a wide range of soft and disordered materials. We demonstrate the applicability and usefulness of the framework on redox-active peptoids functionalized with iron–porphyrin (Fe–P) complexes, a bioinspired platform with programmable donor–acceptor units and tunable three-dimensional organization. The calculated CT rates exhibit strong sensitivity to molecular conformation, with variations spanning several orders of magnitude. This dependence is shown to arise from the pronounced variation in diabatic electronic coupling with the relative orientations and separations of the Fe–P complexes across the conformational ensemble. The framework provides a consistent route for connecting atomistic structure to CT kinetics in the condensed phase and enables analysis of structure–rate relations in organic semiconducting systems.

Charge transfer↗
DOE OSTI2024

Sintering-based Metal Additive Manufacturing Methods for Magnetic Materials

In this chapter, we review the relationship between solid-state sintering and additive manufacturing (AM) methods for fabricating soft and hard magnetic materials. Heat treatment as a post-processing method has been done in conjunction with AM as a method to improve density and/or mechanical properties. In binder jetting (BJT) of metal powders, sintering is a crucial post-processing step and is necessary for obtaining the final product. This is because the parts are only in the “green” state when they leave the BJT printer, with poor mechanical properties and high porosity. Sintering densifies and strengthens the green part into the final product. A potential industrial application for sintering-based AM is the fabrication of magnetic materials. The motivation for doing so, the process and properties of the AM magnets, and the potential applications of post-sintered AM magnets are explored.

Wang, Haobo↗
DOE OSTI2023

The Addition of Boron to Melt-Spun Fe-6.5%Si Ribbons

Fe-6.5%Si has higher electrical resistivity, lower magnetocrystalline anisotropy, and lower magnetostriction than traditional Fe-3.2%Si silicon steel. The reduced iron losses of Fe-6.5%Si render it a highly favorable candidate for high-speed motors and transformers. However, large-scale production of wide Fe-6.5%Si tape by rapid solidification can be challenging mainly because of its high melting point. In this work, boron is alloyed to Fe-6.5%Si to reduce its melting temperature and interfacial energy to improve the alloy’s processability. Boron additions from 0.01 wt.% to 2.24 wt.% into Fe-6.5%Si and its effect on ribbon thickness, grain size, magnetic, and mechanical properties were studied. Further, minor boron alloying significantly changed the melt pool stability and wetting on the quench wheel and in turn increased the quench rate with minimum impact on the magnetic saturation and ductility. Boron addition of < 0.06 wt.% was also found beneficial to the magnetic property of the alloy by lowering both its hysteresis and eddy current losses.

36 MATERIALS SCIENCE↗
DOE OSTI2025

"Soft" Catching high velocity projectiles and targets

In order to perform post mortem analysis on materials launched in gas guns and powder guns, various methods have been explored to soft catch these materials. The majority of the deformation profile must be from the initial impact during the experiment, not from the subsequent impact with the energy absorption material in the catch tank. This process becomes increasingly more difficult with increased velocities. This report explores a method to soft catch materials launched at velocities 3000 $\frac{m}{s}$.

42 ENGINEERING↗
DOE OSTI2022

Impact Response of Control Atmosphere Plasma Spray Deposited Materials

Thermal spray processing of metals and respective blends is becoming increasingly attractive due to the unique properties such as increased yield strength, low ductility, and differences in tensile and compressive strengths that result from microstructural features due to the spray process compared to other additive manufacturing methods. Here we report the results of plate impact experiments applied to Controlled Atmosphere Plasma Spray deposits of tantalum (Ta), niobium (Nb), and a tantalum-niobium blend (TaNb). These methods allowed for definition of the Hugoniot for each material type and the assessment of the Hugoniot Elastic Limit (HEL). Spallation experiments were conducted, and soft recovery of each material type allowed for scanning electron microscopy to characterize the fracture mechanism during tensile loading.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Development of dual phase soft magnetic laminate for advanced electric machines

The development of dual phase soft magnetic laminate for advanced electric machines at General Electric is summarized, including alloy development, properties, manufacturing trials, prototype experience, potential applications, and future material development. Dual phase soft magnetic laminates provide the flexibility to tune magnetic/non-magnetic state at the desired locations, using solution nitriding treatment with protective mask/coating. This enabling material technology benefits electric machine performance by reducing flux leakage in the laminates. It also decouples the electromagnetic and mechanical design, which opens up the design space for advanced electric machines. Magnetic and mechanical properties of dual phase laminates were compared to commercial FeSi and FeCo soft magnetic laminates. Driven by the market needs for high power density and high-speed electric machines, a synchronous reluctance (SynRel) machine without PMs using dual phase soft magnetic laminates was assessed in machine electromagnetic performance as well as rotor stress analysis by finite element simulation. Successful prototype build and testing further retired manufacturing risks and advanced the technology maturity level. Future material development with higher mechanical strength, higher saturation magnetization, higher permeability, and lower loss are highly desired for ground and air transportation electrification.

Rallabandi, Vandana↗
DOE OSTI2025

An Additively Manufactured Fe-3Si Stator for a High-Performance Electrical Motor

Additive manufacturing (AM) has the potential to produce novel high-performance electrical machines, enabling the direct printing of complex shapes and the simultaneous processing of multiple feedstocks in a single build. We examined the properties and functional performance of Fe-3 wt.% Si materials that were printed via selective laser melting, machined down to thin laminates, and stacked to form a stator core of a prototype brushless permanent-magnet electrical motor. Big Area Additive Manufacturing of Nd2Fe14B (NdFeB)–polyphenylene sulfide (PPS) bonded magnets was performed, with them then being magnetized and used for the rotor. The magnetic, mechanical, and electrical properties of the as-printed and various heat-treated thin laminates and the back electromotive force (EMF) of the electrical motors at different rotational speeds were measured. The thin laminates exhibit a maximum relative permeability of 7494 at an applied field of 0.8 Oe and a core loss of about 20 W/lb at 60 Hz with the maximum induction of 15 kg. In addition to the demonstration of AM printing, motor assembly, and complete characterization of printed Fe-3 wt.% Si, this report highlights the areas of improvement needed in printing technologies to achieve AM built electrical motors and the need for isotropic microstructure refinements to make the laminates appropriate for high-mechanical-strength and low-loss rotational electrical devices.

36 MATERIALS SCIENCE↗
DOE OSTI2024

An optimization-based approach to tailor the mechanical response of soft metamaterials undergoing rate-dependent instabilities

An optimization-based design framework is proposed to tune the response of soft metamaterials involving both geometric instabilities and nonlinear viscoelastic material behavior. Designing the response of soft metamaterials to harness instabilities and undergo large, tailored configuration changes will enable advancements in soft robotics, shock and vibration mitigation, and flexible electronics. In line with the metamaterial concept, the response of these materials is governed to a large extent by the geometric and topological makeup of their small-scale features. However, the link between structure and response is less intuitive for soft metamaterials due to their reliance upon highly nonlinear responses triggered by geometric instabilities. This is further complicated by the effects of viscoelastic relaxation, which recent studies have shown to alter the emergence of instabilities in non-intuitive ways. Here, these effects are accounted for in our framework to achieve various design objectives, including tailored force–displacement response and maximized energy absorption from both geometric and material effects. To fully automate this process, it is essential to have a completely robust equation solver for forward problems involving instabilities and viscoelastic relaxation. We achieve this by casting the search for stable mechanical equilibrium — i.e. the forward problem — as a minimization problem and utilize a trust region algorithm to robustly handle instabilities and follow energetically-favorable equilibrium paths through critical points.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS2010

Acoustic Liner for Turbomachinery Applications

The purpose of this innovation is to reduce aircraft noise in the communities surrounding airports by significantly attenuating the noise generated by the turbomachinery, and enhancing safety by providing a containment barrier for a blade failure. Acoustic liners are used in today's turbofan engines to reduce noise. The amount of noise reduction from an acoustic liner is a function of the treatment area, the liner design, and the material properties, and limited by the constraints of the nacelle or casement design. It is desirable to increase the effective area of the acoustic treatment to increase noise suppression. Modern turbofan engines use wide-chord rotor blades, which means there is considerable treatment area available over the rotor tip. Turbofan engines require containment over the rotors for protection from blade failure. Traditional methods use a material wrap such as Kevlar integrated with rub strips and sometimes metal layers (sandwiches). It is possible to substitute the soft rub-strip material with an open-cell metallic foam that provides noise-reduction benefits and a sacrificial material in the first layer of the containment system. An open-cell foam was evaluated that behaves like a bulk acoustic liner, serves as a tip rub strip, and can be integrated with a rotor containment system. Foams can be integrated with the fan-containment system to provide sufficient safety margins and increased noise attenuation. The major innovation is the integration of the foam with the containment.

Huff, Dennis L.↗
DOE OSTI2023

Electron Microscopy Studies of Soft Nanomaterials

This review highlights recent efforts on applying electron microscopy (EM) to soft (including biological) nanomaterials. We will show how developments of both the hardware and software of EM have enabled new insights into the formation, assembly, and functioning (e.g., energy conversion and storage, phonon/photon modulation) of these materials by providing shape, size, phase, structural, and chemical information at the nanometer or higher spatial resolution. Specifically, we first discuss standard real-space two-dimensional imaging and analytical techniques which are offered conveniently by microscopes without special holders or advanced beam technology. The discussion is then extended to recent advancements, including visualizing three-dimensional morphology of soft nanomaterials using electron tomography and its variations, identifying local structure and strain by electron diffraction, and recording motions and transformation by in situ EM. On these advancements, we cover state-of-the-art technologies designed for overcoming the technical barriers for EM to characterize soft materials as well as representative application examples. Here, the even more recent integration of machine learning and its impacts on EM are also discussed in detail. With our perspectives of future opportunities offered at the end, we expect this review to inspire and stimulate more efforts in developing and utilizing EM-based characterization methods for soft nanomaterials at the atomic to nanometer length scales in academic research and industrial applications.

Imaging↗
DOE OSTI2020

Effects of Solidification Cooling Rates on Microstructures and Physical Properties of Fe-6.5%Si Alloys

Compared to the widely used Fe-3.2wt%Si steel, Fe-6.5wt%Si has superior electric and magnetic properties, including higher electrical resistivity, lower iron loss, higher permeability, and near zero magnetostriction. However, Fe-6.5wt%Si sheet is difficult to produce using traditional manufacturing processes as the high silicon content favors the formation of ordered phases that embrittle the material. Fortunately, these ordered phases can be suppressed if the alloy is cooled fast enough from a high temperature kinetically trapping the disordered solid solution or amorphous state. Planar flow casting is known for its rapid solidification rate. In order to consider it as a viable method to manufacture ductile Fe-6.5wt%Si sheets, the effect of cooling rate on physical properties of Fe-6.5wt%Si alloy are systematically investigated. In this work, various cooling rates are achieved by changing melt-spin wheel speeds, which significantly affect the solidification temperature profile and have profound effects on ordering, microstructures, textures, hardness, and magnetic properties. High cooling rates result in refined grains, reduced ordering, enhanced <100> out of the plane texture, decreased hardness, and increased coercivity. This study demonstrates a critical cooling rate at ~1.7 × 10 5 K/s, corresponding to a tangential wheel speed of 5-7 m/s, below which the hardness significantly increases in agreement with the sudden increase of the ordered phases that causes the material embrittlement.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Spectral studies of soft x-ray radiation of laser-produced plasma of various target materials in a wide spectral range

Here, the work is devoted to experimental study of soft X-ray radiation spectra of laser produced plasma in a wide spectral range 5–100 Å at the “Kamerton” facility (GPI) with pulse duration 70 ps, pulse energy 1–5 J, wavelength 0.53 microns at which the laser intensity (power flux density) of 7×10 14 – 3.5×10 15 W/cm 2 was achieved. A spectrograph was used, which had transmission diffraction gratings with a ratio of the elementary gap to the period of the structure of 0.25 and 0.41. Detection was performed on both UV-4 X-ray photo film and Fuji TR fluorescent imaging plate. Solid samples from Al, Si, Ti, Cu, Ta and W were used as targets. The ionization states of the plasma corresponding to various electron temperatures were calculated, which made it possible to estimate the electron temperature by comparison these calculation results with the experimentally obtained spectra. The estimated electron temperature, which depends on the laser pulse energy and the target material, varied within the range of 100–450 eV. To verify the correctness of the temperature estimations obtained by such comparison a numerical simulation of plasma radiation was carried out by the use of PrismSPECT computer program. It was found that the results of this simulation are in a good agreement with estimations on the base of experimentally obtained spectra. The analysis of these spectra showed that tantalum, tungsten or titanium targets are the best candidates among the tested ones for the use of laser produced plasma as a radiation source in the "water window" spectral range (23–44 Å) for applications in biology and medicine.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Mesoporous Crystalline Niobium Oxide with a High Surface Area: A Solid Acid Catalyst for Alkyne Hydration

A mesoporous crystalline niobium oxide with tunable pore sizes was synthesized via the sol–gel-based inverse micelle method. The material shows a surface area of 127 m 2 /g, which is the highest surface area reported so far for crystalline niobium oxide synthesized by soft template methods. The material also has a monomodal pore size distribution with an average pore diameter of 5.6 nm. A comprehensive characterization of niobium oxide was performed using powder X-ray diffraction, Brunauer–Emmett–Teller, thermogravimetric analysis, scanning electron microscopy, transmission electron microscopy, UV–vis, and X-ray photoelectron spectroscopy. The material acts as an environmentally friendly, solid acid catalyst toward hydration of alkynes under with excellent catalytic activity (99% conversion, 99% selectivity, and 4.39 h –1 TOF). Brønsted acid sites present in the catalyst were found to be responsible for the high catalytic activity. Lastly, the catalyst was reusable up to five cycles without a significant loss of the activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Determination of single crystal elastic moduli of KTb3F10 by resonant ultrasound spectroscopy

KTb3F10 (KTF) has been developed in recent years as a candidate Faraday rotator material because of its cubic symmetry, high figures of merit, and low absorption coefficient. While considerable efforts have focused on crystal growth and optical properties, investigations of fundamental thermodynamic behavior of KTF have been limited. Here, we report elastic moduli C11, C12, and C44 of single crystalline KTF measured by resonant ultrasound spectroscopy from 280 K up to 300 K and the obtained temperature derivatives of each modulus. We additionally report the single crystal elastic moduli of the rare-earth garnet Y3Al5O12 (YAG), yielding results that agree well with the prior literature. We found C11=135.62 GPa, C12=58.11 GPa, and C44=44.81 GPa for KTF and C11=332.43 GPa, C12=109.58 GPa, and C44=114.81 GPa for YAG at room temperature. The present results have been compared with previous experimental and theoretical results and with common oxide and fluoride optical materials, revealing the relative softness of KTF. The low elastic moduli of KTF are, in turn, responsible for its low thermal conductivity and low Debye frequency compared to other laser host materials.

Balodhi, Ashiwini (ORCID:0000000290496382)↗