Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SLIDING FRICTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Wear of iron and nickel in corrosive liquid environments

Friction and wear behavior of Fe and Ni sliding on aluminum oxide in aerated sulfuric acid and hydrochloric acid were investigated. The results show that the concentration of acid is an important factor in controlling the metal loss caused by wear corrosion processes in the acids. At very dilute acid concentration (10 to the -4 N), Fe behaves differently from Ni. Fe develops a soft, friable deposit, while Ni develops no corrosion layer. The formation and removal of the corrosion deposit on Fe resulted in high metal loss and coefficient of friction, as compared to the relatively low metal loss and coefficient of friction observed for Ni. At slightly higher acid concentration (10 to the -3 and 10 to the -2 N), no corrosion products were produced on both Fe and Ni. Wear of Fe and Ni was generally at a minimum. At higher acid concentration (10 to the -1 N and above), loss of Fe and Ni increased as the acid concentration increased. In sulfuric acid the maximum loss of both Fe and Ni was at 7.5 N (30 percent) concentration, and the metal losses of both Fe and Ni dropped markedly at 15 N (50 percent) and above. In hydrochloric acid, however, the Fe loss continued to increase with the increase of acid concentration, and the maximum Fe loss occurred in the most concentrated acid (12.1 N, 37 percent). There were variations in loss with Ni from specimen to specimen examined in hydrochloric acids (10 to the -1 N and above). The coefficient of friction for Ni increased slightly with an increase in acid concentration up to 10 to the -2 N. When corrosion started to dominate in the wear-corrosion process, the coefficient of friction decreased in both sulfuric and hydrochloric acids at 10 to the -1 N and above.

Miyoshi, Kazuhisa↗
NASA NTRS1992

Sliding durability of two carbide-oxide candidate high temperature fiber seal materials in air to 900 C

A test program to determine the friction and wear properties of two complex carbide oxide ceramic fibers for high temperature sliding seal applications is described. The fibers are based on Si, C, O, and Ti or Si, C, N, and O ceramic systems. Pin on disk tests using ceramic fiber covered pins and Inconel 718 disks, were conducted in air from 25 to 900 C to evaluate potential seal materials. This testing procedure was used in a previous study of oxide ceramic fibers which were found to exhibit wear behavior based predominantly on their mechanical properties. Like the oxide fibers tested previously, these carbide oxide ceramic fibers, show an increase in friction and wear with increased test temperature. At room temperature, the wear behavior seems to be based upon mechanical properties, namely tensile strength. At 500 and especially 900 C, the fibers wear by both mechanical fracture and by oxidative type wear. Based upon post test microscopic and x ray analyses, interaction between the fiber constituents and elements transferred from the counterface, namely Ni and Cr, may have occurred enhancing the tribochemical wear process. These results are interpreted.

Dellacorte, Christopher↗
DOE OSTI2023

Macroscale Superlubricity Induced by MXene/MoS 2 Nanocomposites on Rough Steel Surfaces under High Contact Stresses

Toward the goal of achieving superlubricity, or near-zero friction, in industrially relevant material systems, solution-processed multilayer Ti 3 C 2 T x -MoS 2 blends are spray-coated onto rough 52100-grade steel surfaces as a solid lubricant. The tribological performance was assessed in a ball-on-disk configuration in a unidirectional sliding mode. The test results indicate that Ti 3 C 2 T x -MoS 2 nanocomposites led to superlubricious states, which has hitherto been unreported for both individual pristine materials, MoS 2 and Ti 3 C 2 T x , under macroscale sliding conditions, indicating a synergistic mechanism enabling the superlative performance. Furthermore, the processing, structure, and property correlation were studied to understand the underlying phenomena. Raman spectroscopy, scanning electron microscopy, and transmission electron microscopy revealed the formation of an in situ robust tribolayer that was responsible for the performance at high contact pressures (>1.1 GPa) and sliding speeds (0.1 m/s). This report presents the lowest friction obtained by either MoS 2 or MXene or any combination of the two so far.

36 MATERIALS SCIENCE↗
NASA NTRS1960

Use of Less Reactive Materials and More Stable Gases to Reduce Corrosive Wear When Lubricating with Halogenated Gases

The gases CF2Cl-CF2Cl, CF2Cl2, and CF2Br-CF2Br were used to lubricate metals, cermets, and ceramics in this study. One of the criteria for determining the effectiveness of a reactive-gas-lubricated systems is the stability of the halogen-containing gas molecule. The carbon-to-halogen bond in the ethane molecule has extremely good thermal stability superior to the methane analogs (CF2Cl2 and CF2Br2) used in earlier research. For this reason, the ethane compounds CF2Cl-CF2Cl and CF2Br-CF2Br were considered as high-temperature lubricants. Friction and wear studies were made with a hemisphere (3/16-in. rad.) rider sliding in a circumferential path on the flat surface of a rotating disk (21/2-in. diam. ). The specimens of metal alloys, cermets, and ceramics were run In an atmosphere of the various gases with a load of 1200 grams, sliding velocities from 75 to 8000 feet per minute, and temperatures from 75 to 1400 F. The gas CF2Cl-CF2Cl was found to be an effective lubricant for the cermet LT-LB (59.0 Cr, 19.0 Al2O3, 20.0 Mo, 2.0 Ti) and the ceramic Al2O3 sliding on Stellite Star J (cobalt-base alloy) at temperatures to 1400 F. The bromine-containing gas CF2Br-CF2Br was found to give friction and wear values that can be considered to be in a region of effective boundary lubrication for the cermet K175D (nickel-bonded metal carbide) sliding on the metal Hastelloy R-235 (nickel-base alloy) at temperatures to 1200 F.

Buckley, Donald H.↗
NASA NTRS1986

Tribolgy of selected ceramics at temperatures to 900 deg C

Results of fundamental and focused research on the tribological properties of ceramics are discussed. The basic friction and wear characteristics are given for ceramics of interest for use in gas trubine, adiabatic diesel, and Stirling engine applications. The importance of metal oxides in ceramic/metal sliding combinations is illustrated. The formulation and tribological additives are described. Friction and wear date are given for carbide and oxide-based composite coatings for temperatures to at least 900 C.

Sliney, H. E.↗
NASA NTRS1986

Tribology of selected ceramics at temperatures to 900 C

Results of fundamental and focused research on the tribological properties of ceramics are discussed. The basic friction and wear characteristics are given for ceramics of interest for use in gas turbine, adiabatic diesel, and Stirling engine applications. The importance of metal oxides in ceramic/metal sliding combinations is illustrated. The formulation and tribological additives are described. Friction and wear data are given for carbide and oxide-based composite coatings for temperatures to at least 900 C.

Sliney, H. E.↗
DOE OSTI2025

Friction and wear of nuclear graphite exposed to molten FLiNaK salt environment

This report formally documents the completion of the Advanced Reactor Technologies Level 3 Milestone (M3TG-25OR0501104), “Initiate graphite wear studies of graphite samples exposed to molten salt environment,” due August 1, 2025. The report summarizes the ongoing activities aimed at characterizing the friction and wear behavior of graphite in molten LiF–NaF–KF (FLiNaK) salt environment. The wear and friction behavior of self-mated ET-10 nuclear graphite were tested at varying temperatures (550°C and 650°C), contact loads (40 and 80 N) and sliding speeds (1 and 10 mm/s) in a controlled argon environment. The results were compared to the wear and friction behavior of the same graphite material in a dry argon environment. This report presents initial studies on the friction and wear behavior of graphite in sliding contact mode, with future work focused on investigating the graphite matrix materials, as well as rolling and impact contact modes. The outcomes of this report could provide insights into assessing the integrity of the graphitic components of pebble-bed fluoride salt–cooled high-temperature reactors (PB-FHRs) to enhance their safe operation.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Mesoscale Modeling of Hydrogels Under Frictional Shear Stress

Hydrogels are three-dimensional networks of hydrophilic polymers often used as a simplified model of hydrated biological materials, from cartilaginous joints to the ocular tear film. However, the lubrication mechanisms of hydrogels remain poorly understood, partly due to their complex polymeric structure, which creates blurred interfaces during sliding that are challenging to study experimentally. In this study, we employ dissipative particle dynamics (DPD) to investigate the frictional behavior of a polymeric hydrogel network sliding against a solid wall in an explicit viscous solvent. This computational approach enables us to model hydrodynamic interactions and mesoscale polymer dynamics, capturing key aspects of hydrogel friction. Our simulations reveal that hydrogel friction is governed by the interplay between polymer relaxation and viscous shear, characterized by the Weissenberg number (Wi). At low Wi, friction coefficient remain nearly constant, dominated by polymer relaxation. However, at higher Wi, friction is dominated by viscous drag within a near-wall solvent layer, leading to a linear increase in friction coefficient with Wi. Furthermore, our results demonstrate an inverse relationship between the friction coefficient and the applied normal load, consistent with experimental observations. This work provides new insights into the fundamental tribological properties of hydrogels, shedding light on the micromechanics of hydrogel friction. Improving our understanding of hydrogel structure and dynamics under friction advances our knowledge of the mechanisms regulating biological lubrication in health and disease.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Tunable amorphous carbon films formed on ultralow wear, Pt–Au alloys

The mechanocatalytic formation of carbonaceous films at the interface between sliding metallic contacts is simultaneously advantageous for reducing friction and adhesion in several tribological applications and detrimental for electrical contacts as they can induce device failure by increasing the contact resistance. Yet, remarkably little is still known about the chemistry, structural and mechanical properties, and tunability of these interfacial layers. In this study, we performed contact pressure-dependent tribological experiments in dry nitrogen containing trace organics on four, nanocrystalline Pt–Au alloys ([Au] from 0 at.% to 10 at.%) – a promising class of alloys for ultralow wear and electrical contact applications. The ex-situ, multi-technique characterization results did not only provide insights into the chemical nature and mechanical behavior of the mechanocatalytic, carbon-rich films formed on Pt–Au surfaces, but also revealed the interplay between catalytic and mechanochemical tribofilm formation controlled by the composition-dependent electronic structure of the Pt–Au substrate and the applied contact pressure. The results of this work provide guidelines for tailoring nanocrystalline alloys to control their mechanocatalytic activity on the basis of variations of the alloy mechanical properties and element's electronic structure with the alloy stoichiometry.

AFM↗
DOE OSTI2023

The Role of Clay in Limiting Frictional Healing in Fault Gouges

Abstract Frictional healing is fundamental to the seismic cycle and plays a role in the energy balance, dynamics, and recurrence interval of earthquakes and slow slip events. Although the healing behavior of quartz has been studied extensively, the role of clay content is less understood. We tested synthetic mixtures of quartz and smectite (10%–100% smectite) in a double‐direct shear configuration to measure frictional healing. We show that the magnitude and rate of healing decreases systematically with higher clay content (from 0.008/decade at 10% smectite to 0.002/decade at 100% smectite). Healing scales with both the magnitude of stress relaxation during holds and layer‐normal compaction of the gouge. We suggest this reflects the alignment of clay minerals, leading to saturation of the real area of contact that limits restrengthening during holds. The low healing rates of clay‐rich faults—together with rate‐neutral to rate‐strengthening friction—should promote frequent, small failures or stable sliding.

58 GEOSCIENCES↗
NASA NTRS1989

Contact solution algorithms

Two algorithms for obtaining static contact solutions are described in this presentation. Although they were derived for contact problems involving specific structures (a tire and a solid rubber cylinder), they are sufficiently general to be applied to other shell-of-revolution and solid-body contact problems. The shell-of-revolution contact algorithm is a method of obtaining a point load influence coefficient matrix for the portion of shell surface that is expected to carry a contact load. If the shell is sufficiently linear with respect to contact loading, a single influence coefficient matrix can be used to obtain a good approximation of the contact pressure distribution. Otherwise, the matrix will be updated to reflect nonlinear load-deflection behavior. The solid-body contact algorithm utilizes a Lagrange multiplier to include the contact constraint in a potential energy functional. The solution is found by applying the principle of minimum potential energy. The Lagrange multiplier is identified as the contact load resultant for a specific deflection. At present, only frictionless contact solutions have been obtained with these algorithms. A sliding tread element has been developed to calculate friction shear force in the contact region of the rolling shell-of-revolution tire model.

Tielking, John T.↗
NASA NTRS1993

Linear Motor With Air Slide

Improved linear actuator comprises air slide and linear electric motor. Unit exhibits low friction, low backlash, and more nearly even acceleration. Used in machinery in which positions, velocities, and accelerations must be carefully controlled and/or vibrations must be suppressed.

Johnson, Bruce G.↗
NASA NTRS1980

Measurement of rod seal lubrication for Stirling engine

The elastohydrodynamic behavior of sliding elastomeric seals for the Stirling engine, was analyzed using an experimental apparatus to determine the instantaneous oil film thickness throughout the cyclic reciprocating motion. Tests were conducted on two commercial elastomeric seals: a "T" seal (76 mm O.D. and 3.8 mm between backing rings) and an "O" ring (76 mm O.D. and 5.3 mm diameter). Testing conditions included seal durometers of 70 and 90, sliding velocities of 0.8, 2.0, and 3.6 m/s, and no pressure gradient across the seal. Both acrylic and aluminum cylinders were used. Measured oil film thickness profiles were compared to results of the elastohydrodynamic analysis. The comparison shows an overall qualitative agreement. Friction and oil leakage measurements were also made at these sliding speeds. The fluid used was a typical synthetic base automotive lubricant. It is concluded that this first time experimental analytical comparison for oil film thickness indicates the need for some improvements in the analytical model and in the experimental technique.

Krauter, A. I.↗
DOE OSTI2021

Structurally Driven Environmental Degradation of Friction in MoS2 Films

Abstract We report an investigation of the friction mechanisms of MoS 2 thin films under changing environments and contact conditions using a variety of computational and experimental techniques. Molecular dynamics simulations were used to study the effects of water and molecular oxygen on friction and bonding of MoS 2 lamellae during initial sliding. Characterization via photoelectron emission microscopy (PEEM) and Kelvin probe force microscopy (KPFM) were used to determine work function changes in shear modified material within the top few nanometers of MoS 2 wear scars. The work function was shown to change with contact conditions and environment, and shown by density functional theory (DFT) calculations and literature reports to be correlated with lamellae size and thickness of the basally oriented surface layer. Results from nanoscale simulations and macroscale experiments suggest that the evolution of the friction behavior of MoS 2 is linked primarily to the formation or inhibition of a basally oriented, molecularly thin surface film with long-range order.

Curry, John F.↗
NASA NTRS1995

The effects of ion implantation on the tribology of perfluoropolyether-lubricated 440C stainless steel couples

The lubricating lifetime of thin films of a perfluoropolyether (PFPE) based on hexafluoropropene oxide in the presence of ion implanted 440C stainless steel is presented. Stainless steel discs, either unimplanted or implanted with N2, C, Ti, Ti + N2, or Ti + C had a thin film of PFPE (60-400 A) applied to them reproducibly (+/- 20 percent) and uniformly (+/- 15 percent) using a device developed for this study. The lifetimes of these films were quantified by measuring the number of sliding-wear cycles required to induce an increase in the friction coefficient from an initial value characteristic of the lubricated wear couple to a final, or failure value, characteristic of an unlubricated, unimplanted couple. The tests were performed in a dry nitrogen atmosphere (less than 1 percent RH) at room temperature using a 3 N normal load with a relative sliding speed of 0.05 m/s. The lubricated lifetime of the 440C couple was increased by an order of magnitude by implanting the disc with Ti. Ranked from most to least effective, the implanted species were: Ti; Ti+C; unimplanted; N2; C approximately equals Ti+N2. The mechanism postulated to explain these results involves the formation of a passivating or reactive layer which inhibits or facilitates the production of active sites. The corresponding surface microstructures induced by ion implantation, obtained using x-ray diffraction and conversion electron Mossbauer spectroscopy, ranked from most to least effective in enhancing lubricant lifetime were: amorphous Fe-Cr-Ti; amorphous Fe-Cr-Ti-C + TiC; unimplanted; epsilon-(Fe,Cr)(sub x)N, x = 2 or 3; amorphous Fe-Cr-C approximately equals amorphous Fe-Cr-Ti-N.

Shogrin, Bradley↗
DOE OSTI2020

Slide Test FY 2019 Report

At Los Alamos, the Slide Test was developed in 2019 to investigate whether the mass of a main charge of explosive sliding on a gritty surface, in the absence of impact, is sufficient to heat grit to ignition temperatures in PBX 9501. This is a practical test to address frictional ignition during assembly/disassembly operations at the Pantex Plant. Twenty-seven Slide Tests were performed in total, testing PBX 9501 at various slide velocities, grit diameters, grit patterns, and charge masses. Time-resolved velocimetry of the slide event (from PDV) and spot area of the explosive charge (obtained from image analysis) is reported. High-speed videography is used to diagnose explosive reaction. Eighteen of these tests were performed with a charge mass of 30 lbs at velocities ≤ 4 m s-1 and grit diameters between 75 and 1000 µm. Nine Slide Tests were performed with a 15 lb charge mass at similar parameters. No ignition was observed in any of the tests. These data provide evidence that the mass of a main charge, caused to slide on a surface at the low velocities achievable during routine handling, is insufficient stimulus to heat grit to ignition temperatures. These findings are relevant to risk assessment for explosive handling operations and provide evidence that PBX 9501 is safe within the constraints that were tested. However, because ignitions were not observed in any of the tests, we cannot determine which variables (mass or velocity) dominate the explosive response and to what extent. The absence of observed ignition also precludes the determination of a safety margin. To identify this safety margin, further research would be necessary to define the velocity and/or mass threshold at which ignition occurs.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗