Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SINTERED MATERIALS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Unraveling the nature of sulfide ions in hydrometallurgical recycling of NCM622 cathode material

The use of lithium-ion batteries (LIBs) has increased dramatically since its initial inception in the late 20th century. Such a surge in the LIB market and industry has resulted in a huge demand for mineral resources. Besides, the large scale of production will lead to massive amounts of waste batteries in the end. As such, recycling is seen as an end-of-pipe process to resolve sustainability and environmental concerns. The hydrometallurgical recycling is considered to be the most prominent method to recover cathode materials from spent LIBs owing to its high leaching efficiency and low energy costs. A series of procedures including pretreatment of the spent LIBs, acid leaching of the black mass, chemical co-precipitation of the hydroxide precursor, and sintering of the cathode active material need to be operated precisely. In this aspect, the impurities introduced during the process could pose a serious threat to the reaction stability as well as recycling consistency. Here, the impact of sulfide ions on recovered LiNi 0.6 Co 0.2 Mn 0.2 O 2 (NCM622) cathode material with the method of hydrometallurgy is first investigated in detail. This study shows that hydrometallurgical process is not obviously influenced by sulfide impurity. No signs of secondary phase or impurity inclusion are spotted in synthesized cathodes. Under 5 at % sulfide concentration conditions, the obtained NCM622 cathode exhibits a capacity of 159.4 mAh/g after 100 cycles at 1/3C, which is at the same level as virgin benchmark. The difference in rate performance between cathodes with and without additional sulfide is less than 2 % or even smaller. In short, the results indicate a neutral status of sulfide ions in hydrometallurgical recycling.

25 ENERGY STORAGE↗

Effects of Holding Time on the Sintering of Cemented Tungsten Carbide Powder and Bonding with High-Strength Steel Wire

Cemented tungsten carbide (WC-10Co) and high-strength (AISI 4340) steel were successfully bonded by hot compaction diffusion bonding at a low temperature. The effects of holding time (5-50 min) on microstructure and mechanical properties of the sintered carbides and bonding strengths of the dissimilar bilayered composite materials were examined. The results show that the mechanical properties of the carbides increase, but the bonding strength increases firstly and then decreases with the increase in holding time. The maximum density and hardness achieved are 95.92 and 99.5%, respectively. A transitional layer forms at the interface as a result of elemental interdiffusion. The depth of the layer increases with the increase in holding time. The optimal bonding time is determined to be 40 min at a temperature of 1200°C and a pressure 160 MPa, by which the maximum bonding strength of 204 MPa of the WC-10Co/4340 steel joints can be achieved.

36 MATERIALS SCIENCE↗

Effect of the sintering temperature on the properties of Ce{sub 0.85}La{sub 0.10}Ca{sub 0.05}O{sub 2-{delta}} electrolyte material

Rare earth and alkaline earth co-doped Ce{sub 0.85}La{sub 0.10}Ca{sub 0.05}O{sub 2-{delta}} electrolyte material with the powder obtained by solid-state reaction method was sintered at 1300, 1400, 1500 and 1600 {sup o}C respectively. The results showed that the ionic conductivity of the sample sintered at 1400 {sup o}C was slightly lower compared to that sintered at 1500 {sup o}C in the temperature range of 300-550 {sup o}C, while the sample sintered at 1400 {sup o}C showed the highest ionic conductivity in all the samples above 550 {sup o}C. The ionic conductivity of {approx}0.021 S/cm at 600 {sup o}C and the relative density of 98.2% were observed for the sample sintered at 1400 {sup o}C. In addition, the highest flexural strength with 145 MPa was also obtained for the sample sintered at 1400 {sup o}C. It suggested that the sintering temperature for Ce{sub 0.85}La{sub 0.10}Ca{sub 0.05}O{sub 2-{delta}} electrolyte may be reduced to as low as 1400 {sup o}C with desired properties.

36 MATERIALS SCIENCE↗

Synthesis, Processing and Properties of Calcium- and Nickel-Doped Yttrium Chromates(III) Y{sub 0.8}Ca{sub 0.2}Cr{sub 1−x}Ni{sub x}O{sub 3} (x = 0-0.3) and Studies on Their Potential Application as Coatings for SOFC Interconnects

In the present study, a calcium- and nickel-doped yttrium chromates (YCCN)-based, conductive–protective layers for metallic interconnects used in the intermediate-temperature solid oxide fuel cells (IT-SOFCs) were investigated. Synthesis of Y{sub 0.8}Ca{sub 0.2}Cr{sub 1−x}Ni{sub x}O{sub 3} (x = 0; 0.15 and 0.3) powders was performed using a wet chemistry method with two different complexing agents: ethylenediaminetetraacetic acid and glycine. Based on the result of thermal analysis of obtained precursors, optimal conditions of the calcination process were determined. Powders were then milled, compacted and sintered at different temperatures using free sintering method, into series of dense, polycrystalline sinters. The use of glycine precursor allowed obtaining a single-phase material in all cases. Based on the electrical and sintering properties, the Y{sub 0.8}Ca{sub 0.2}Cr{sub 0.85}Ni{sub 0.15}O{sub 3} material was selected for further studies. It was deposited using cost-effective screen-printing method on the Crofer 22APU ferritic stainless steel. To investigate properties and suitability of the resulting layer/steel system for IT-SOFCs applications, the high-temperature, dual-atmosphere studies were carried out for the first time for ceramic/metallic system, in conditions as close as possible to actual working conditions of the fuel cell. The layer exhibited high stability and good protective properties. The area-specific resistance of the studied ceramic layer/metallic substrate composite was determined, with the obtained value of 0.0366 Ω cm{sup 2} being within the arbitrary limit set for these materials (0.1 Ω cm{sup 2}). The results show that the investigated materials are suitable for the projected application.

36 MATERIALS SCIENCE↗

Control of donor-like effect in V2VI3 polycrystalline thermoelectric materials

Highlights: • Thermal control of donor-like effect for V{sub 2}VI{sub 3} polycrystalline materials is proposed. • Low-temperature sintering or hot deforming facilitates the donor-like effect. • Recovery role by high-temperature sintering/deforming enhances the Seebeck coefficient. • Temperature should be strictly selected for each V{sub 2}VI{sub 3} polycrystalline material. - Abstract: Intrinsic point defect plays a core role in improving thermoelectric performance of V{sub 2}VI{sub 3} polycrystalline materials. However, the control of intrinsic point defect is challenging during powder refinement due to the donor-like effect. This paper shows a systematic approach to thermal control the donor-like effect via engineering spark plasma sintering and hot deformation temperature. Bi{sub 2}Te{sub 2.85}Se{sub 0.15} polycrystalline alloy with high electron concentration was chosen as example to validate the method. The low Seebeck coefficient of n-type Bi{sub 2}Te{sub 2.85}Se{sub 0.15} polycrystalline, arising from strong donor-like effect after powder refinement, was enhanced by recovery role induced reduction in electron concentration through proper tuning sintering or deforming temperature. Repetitive hot deformation was applied to further improve the Seebeck coefficient via the recovery role and a maximum zT of 1.0 is obtained at 410 K. The present results give insights into developing higher performance V{sub 2}VI{sub 3} polycrystalline materials through thermal control the donor-like effect.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Acetabular Cup with a Trabecular Coating: A Novel Approach to a Monolithic Cup Made of One High-Strength Ceramic Material

An advanced monolithic cup comprising a thin liner and a trabecular coating is a promising alternative to the current modular ceramic cups for hip replacements because it can be anchored directly to the human bone and features larger femoral heads allowing a greater range of motion. In this study, the authors propose a fabrication route for an advanced monolithic cup of only one high-strength ceramic material by joining a partially sintered liner and a coating with a ceramic paste as an intermediate layer and subsequent sintering. Therefore, the challenge here is to avoid the formation of defects at the coating/intermediate layer interfaces during classical sintering which is due to compressive tension constrained coating sintering in the initial sintering stages. In this study, the defect formation is minimized by sintering at constant low shrinkage rates, as this results in favorable compressive stresses in the coating in the initial sintering stages and a decrease in the differences in the densification rates. For the first time, by using the proposed route, the authors prepare an advanced monolithic cup of only alumina-toughened zirconia (ATZ) that contains a coating with a porosity of 50 vol% and interconnected pores between 150 and 450 μm, as required for bone-ingrowth.

36 MATERIALS SCIENCE↗

Enhanced dielectric constant and relaxor behavior realized by dual stage sintering of Sr{sub 0.5}Ba{sub 0.5}Nb{sub 2}O{sub 6}

The relaxor ferroelectric compound, Sr{sub 0.5}Ba{sub 0.5}Nb{sub 2}O{sub 6} (SBN50) was synthesized by solid state reaction followed by sintering under two different conditions: single and dual stage sintering. The impact of sintering process on structural and dielectric properties has been studied in detail using X-ray diffraction, scanning electron microscopy and broadband dielectric spectroscopy. The crystal structure determined by performing Rietveld refinement of X-ray diffractogram was found to be identical in both cases. SBN50 crystallizes in the ferroelectric tetragonal tungsten bronze, P4bm structure. It was observed that uniform grain growth can be controlled by dual stage sintering and relatively narrow distribution of grains can be achieved with an average grain size of ∼15 μm. The dielectric studies show that SBN50 exhibits a relaxor ferroelectric behavior with the transformation taking place at ∼ 380 K due to formation of polar nano regions. Although both single and dual stage sintered SBN50 exhibits relaxor behaviour, the maximum dielectric constant of dual stage sintered SBN50 is found to be 1550 compare to 1440 for single stage sintering.

36 MATERIALS SCIENCE↗

Localized Overheating Phenomena and Optimization of Spark-Plasma Sintering Tooling Design

The present paper shows the application of a three-dimensional coupled electrical, thermal, mechanical finite element macro-scale modeling framework of Spark Plasma Sintering (SPS) to an actual problem of SPS tooling overheating, encountered during SPS experimentation. The overheating phenomenon is analyzed by varying the geometry of the tooling that exhibits the problem, namely by modeling various tooling configurations involving sequences of disk-shape spacers with step-wise increasing radii. The analysis is conducted by means of finite element simulations, intended to obtain temperature spatial distributions in the graphite press-forms, including punches, dies, and spacers; to identify the temperature peaks and their respective timing, and to propose a more suitable SPS tooling configuration with the avoidance of the overheating as a final aim. Electric currents-based Joule heating, heat transfer, mechanical conditions, and densification are imbedded in the model, utilizing the finite-element software COMSOL™, which possesses a distinguishing ability of coupling multiple physics. Thereby the implementation of a finite element method applicable to a broad range of SPS procedures is carried out, together with the more specific optimization of the SPS tooling design when dealing with excessive heating phenomena.

36 MATERIALS SCIENCE↗

Thermoelectric and mechanical properties of spark plasma sintered Cu{sub 3}SbSe{sub 3} and Cu{sub 3}SbSe{sub 4}: Promising thermoelectric materials

We report the synthesis of thermoelectric compounds, Cu{sub 3}SbSe{sub 3} and Cu{sub 3}SbSe{sub 4}, employing the conventional fusion method followed by spark plasma sintering. Their thermoelectric properties indicated that despite its higher thermal conductivity, Cu{sub 3}SbSe{sub 4} exhibited a much larger value of thermoelectric figure-of-merit as compared to Cu{sub 3}SbSe{sub 3}, which is primarily due to its higher electrical conductivity. The thermoelectric compatibility factor of Cu{sub 3}SbSe{sub 4} was found to be ∼1.2 as compared to 0.2 V{sup −1} for Cu{sub 3}SbSe{sub 3} at 550 K. The results of the mechanical properties of these two compounds indicated that their microhardness and fracture toughness values were far superior to the other competing state-of-the-art thermoelectric materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Long-term Sustainability of Fracture Conductivity in Geothermal Systems using Proppants

Long-term sustainability of fracture conductivity is critical for commercial success of engineered geothermal system (EGS) and hydrogeothermal field sites. The injection of proppants has been suggested as a means to enhance the conductivity in these systems. Several studies have examined the chemical behavior of proppants that are not at chemical equilibrium with the reservoir rock and water. These studies have suggested that in geothermal systems, geochemical reactions can lead to enhance proppant dissolution and deposition alteration minerals. We hypothesize that proppant dissolution will decrease the strength of the proppant and can potentially reduce the conductivity of the fracture. To examine the geomechanical strength of proppants, we have performed modified crushing tests of proppants and reservoir rock material that was subjected to geothermal reservoir temperature conditions. The batch reactor experiments heated crushed quartz monzonite rock material, proppants (either quartz sand, sintered bauxite or kryptospheres) with Raft River geothermal water to 250 ºC for a period of 2 months. Solid and liquid samples were shipped to University of Utah for chemical characterization with ICP-OES, ICP-MS, and SEM. A separate portion of the rock/proppant material was subjected to a modified American Petroleum Institute ISO 13503-2 proppant crushing test. This test is typically used to determine the maximum stress level that can be applied to a proppant pack without the occurrence of unacceptable proppant crushing. We will use the test results to examine potential changes in proppant/reservoir rock geomechanical properties as compared to samples that have not been subjected to geothermal conditions. These preliminary results will be used to screen the proppants for long term use in EGS and hot hydrogeothermal systems.

fracture sustainability↗

Observations of Oxygen Ion Behavior in the Lithium-Based Electrolytic Reduction of Uranium Oxide

Parametric studies were performed on a lithium-based electrolytic reduction process at bench-scale to investigate the behavior of oxygen ions in the reduction of uranium oxide for various electrochemical cell configurations. Specifically, a series of eight electrolytic reduction runs was performed in a common salt bath of LiCl – 1 wt% Li2O. The variable parameters included fuel basket containment material (i.e., stainless steel wire mesh and sintered stainless steel) and applied electrical charge (i.e., 75 – 150% of the theoretical charge for complete reduction of uranium oxide in a basket to uranium metal). Samples of the molten salt electrolyte were taken at regular intervals throughout each run and analyzed to produce a time plot of Li2O concentrations in the bulk salt over the course of the runs. Following each run, the fuel basket was sectioned and the fuel was removed. Samples of the fuel were analyzed for the extent of uranium oxide reduction to metal and for the concentration of salt constituents, i.e., LiCl and Li2O. Extents of uranium oxide reduction ranged from 43 – 70% in stainless steel wire mesh baskets and 8 – 33 % in sintered stainless steel baskets. The concentrations of Li2O in the salt phase of the fuel product from the stainless steel wire mesh baskets ranged from 6.2 – 9.2 wt%, while those for the sintered stainless steel baskets ranged from 26 – 46 wt%. Another series of tests was performed to investigate the dissolution of Li2O in LiCl at 650 °C across various cathode containment materials (i.e., stainless steel wire mesh, sintered stainless steel and porous magnesia) and configurations (i.e., stationary and rotating cylindrical baskets). Dissolution of identical loadings of Li2O particulate reached equilibrium within one hour for stationary stainless steel wire mesh baskets, while the same took several hours for sintered stainless steel and porous magnesia baskets. Rotation of an annular cylindrical basket of stainless steel wire mesh accelerated the Li2O dissolution rate by more than a factor of six.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Joining of dissimilar materials

A method of joining dissimilar materials having different ductility, involves two principal steps: Decoration of the more ductile material's surface with particles of a less ductile material to produce a composite; and, sinter-bonding the composite produced to a joining member of a less ductile material. The joining method is suitable for joining dissimilar materials that are chemically inert towards each other (e.g., metal and ceramic), while resulting in a strong bond with a sharp interface between the two materials. The joining materials may differ greatly in form or particle size. The method is applicable to various types of materials including ceramic, metal, glass, glass-ceramic, polymer, cermet, semiconductor, etc., and the materials can be in various geometrical forms, such as powders, fibers, or bulk bodies (foil, wire, plate, etc.). Composites and devices with a decorated/sintered interface are also provided.

36 MATERIALS SCIENCE↗

Improving protonic ceramic electrochemical cell performance via a dual-phase reaction-sintered bilayer electrolyte

Protonic ceramic electrochemical cells (PCCs) are promising energy conversion devices, but their fabrication remains challenging. In particular, the typical electrolytes for PCCs such as BaCe 0.7 Zr 0.1 Y 0.1 Yb 0.1 O 3−δ (7111) and BaCe 0.4 Zr 0.4 Y 0.1 Yb 0.1 O 3−δ (4411) suffer from intrinsic barium evaporation issues during high-temperature sintering. This tendency towards barium loss, combined with their highly refractory nature, leads to a tradeoff between sinterability and chemical stability. To address this tradeoff, we propose a bilayer electrolyte combining layers of 4411 and 7111 materials that is designed to enhance sinterability and conductivity through dual-phase reactive sintering. Our findings demonstrate that the bilayer structure exhibits shrinkage behavior closely matched to that of the fuel electrode substrate, with a higher shrinkage compared to a single-layer 4411 electrolyte. Utilizing this bilayer electrolyte structure, our PCCs achieve a peak power density of 637 mW∙cm −2 in fuel-cell mode and a current density of 1060 mA∙cm −2 at 1.3 V in electrolysis mode at 600 °C. Our PCCs demonstrate high Faradaic efficiency of 83% at 1.3 V and 500 °C. Hybrid distribution of relaxation times (DRT) polarization mapping further reveals that the bilayer structure reduces Ohmic and polarization resistance in both fuel-cell and electrolysis modes.

ceramic processing↗

Direct in situ observation of electric field assisted densification of ZnO by energy dispersive X-ray diffraction

Electric field assisted sintering techniques are used to enhance the densification process, reducing sintering time and temperature. Here, we report the in situ characterization of non-isothermal densification behavior of zinc oxide under simultaneous application of thermal and electric field by energy dispersive X-ray diffraction. 99% density was achieved under the electric field of 50 V/mm in the 588–843 °C range in a short time without grain growth. The in-situ energy dispersive X-ray diffraction study revealed the abnormal volumetric unit cell expansion of 0.9% at 843 °C associated with the observed sudden rise of the power absorption by the specimen during densification. Furthermore, the variation in peak broadening as a function of time exhibited singularity in the 588–843 °C range implying the formation and rearrangement of defects correlated with densification during electric field assisted sintering.

36 MATERIALS SCIENCE↗

The sol–gel autocombustion as a route towards highly CO 2 -selective, active and long-term stable Cu/ZrO 2 methanol steam reforming catalysts

The adaption of the sol-gel autocombustion method to the Cu/ZrO 2 system opens new pathways for the specific optimisation of the activity, long-term stability and CO 2 selectivity of methanol steam reforming (MSR) catalysts. Calcination of the same post-combustion precursor at 400 °C, 600 °C or 800 °C allows accessing Cu/ZrO 2 interfaces of metallic Cu with either amorphous, tetragonal or monoclinic ZrO 2 , influencing the CO 2 selectivity and the MSR activity distinctly different. While the CO 2 selectivity is less affected, the impact of the post-combustion calcination temperature on the Cu and ZrO 2 catalyst morphology is more pronounced. A porous and largely amorphous ZrO 2 structure in the sample, characteristic for sol-gel autocombustion processes, is obtained at 400 °C. This directly translates into superior activity and long-term stability in MSR compared to Cu/tetragonal ZrO 2 and Cu/monoclinic ZrO 2 obtained by calcination at 600 °C and 800 °C. The morphology of the latter Cu/ZrO 2 catalysts consists of much larger, agglomerated and non-porous crystalline particles. Based on aberration-corrected electron microscopy, we attribute the beneficial catalytic properties of the Cu/amorphous ZrO 2 material partially to the enhanced sintering resistance of copper particles provided by the porous support morphology.

36 MATERIALS SCIENCE↗

Electrically-conductive proppant and methods for making and using same

Electrically-conductive sintered, substantially round and spherical particles and methods for producing such electrically-conductive sintered, substantially round and spherical particles from an alumina-containing raw material. Methods for using such electrically-conductive sintered, substantially round and spherical particles in hydraulic fracturing operations.

36 MATERIALS SCIENCE↗

Processing Techniques for ODS Stainless Steels

Oxide dispersion-strengthened (ODS) alloys have been studied extensively, in part as a response to the need to develop the high-temperature materials that are required for energy efficient systems. ODS stainless steels, in particular, are of technological interest because of their high ductility and high strength at elevated temperatures, which when combined with their resistance to corrosion, render them ideal for many applications that require extreme performance quality. Survey of the published literature reveals that efforts have been devoted to incorporate specific strengthening mechanisms in order to meet demanding performance criteria for ODS alloys. As a result, a number of novel processing approaches have been developed in an effort to design distinct microstructures that can enhance the performance of ODS alloys. In the current paper, various techniques used to manufacture ODS stainless steel alloys are compared and summarized on the basis of a literature search, and results are contrasted with selected experimental data obtained by the authors. In particular, cryomilling, water-atomization, and melt-spinning processes are described in detail as three novel approaches that can be effectively used to distribute nanometric oxides in 316L stainless steel matrix. The microstructural features, mechanical properties, and sintering behavior of the fabricated materials are described and discussed. The critical processing parameters for each processing technique are discussed with reference to the properties of the material. The versatility and potential challenges of the individual techniques are also described and contrasted.

36 MATERIALS SCIENCE↗