Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “QUALITY FACTOR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

FRACTIONAL AMPLITUDE OF KILOHERTZ QUASI-PERIODIC OSCILLATION FROM 4U 1728-34: EVIDENCE OF DECLINE AT HIGHER ENERGIES

A kilohertz quasi-periodic oscillation (kHz QPO) is an observationally robust high-frequency timing feature detected from neutron star low-mass X-ray binaries (LMXBs). This feature can be very useful to probe the superdense core matter of neutron stars and the strong gravity regime. Although many models exist in the literature, the physical origin of kHz QPO is not known, and hence this feature cannot be used as a tool yet. The energy dependence of kHz QPO fractional rms amplitude is an important piece of the jigsaw puzzle to understand the physical origin of this timing feature. It is known that the fractional rms amplitude increases with energy at lower energies. At higher energies, the amplitude is usually believed to saturate, although this is not established. We combine tens of lower kHz QPOs from a neutron star LMXB 4U 1728-34 in order to improve the signal-to-noise ratio. Consequently, we, for the first time to the best of our knowledge, find a significant and systematic decrease of the fractional rms amplitude with energy at higher photon energies. Assuming an energy spectrum model, blackbody+powerlaw, we explore if the sinusoidal variation of a single spectral parameter can reproduce the above-mentioned fractional rms amplitude behavior. Our analysis suggests that the oscillation of any single blackbody parameter is favored over the oscillation of any single power-law parameter, in order to explain the measured amplitude behavior. We also find that the quality factor of a lower kHz QPO does not plausibly depend on photon energy.

79 ASTRONOMY AND ASTROPHYSICS↗

Characterization of etch pits found on a large-grain bulk niobium superconducting radio-frequency resonant cavity

The performance of superconducting radio-frequency (SRF) resonant cavities made of bulk niobium is limited by nonlinear localized effects. Surface analysis of regions of higher power dissipation is thus of intense interest. Such areas (referred to as “hotspots”) were identified in a large-grain single-cell cavity that had been buffered-chemical polished and dissected for examination by high resolution electron microscopy, electron backscattered diffraction microscopy (EBSD), and optical microscopy. Pits with clearly discernible crystal facets were observed in both “hotspot” and “coldspot” specimens. The pits were found in-grain, at bicrystal boundaries, and on tricrystal junctions. They are interpreted as etch pits induced by crystal defects (e.g. dislocations). All coldspots examined had a qualitatively lower density of etch pits or relatively smooth tricrystal boundary junctions. EBSD mapping revealed the crystal orientation surrounding the pits. Locations with high pit density are correlated with higher mean values of the local average misorientation angle distributions, indicating a higher geometrically necessary dislocation content. In addition, a survey of the samples by energy dispersive x-ray analysis did not show any significant contamination of the samples’ surface. In conclusion, the local magnetic field enhancement produced by the sharp-edge features observed on the samples is not sufficient to explain the observed degradation of the cavity quality factor, which starts at peak surface magnetic field as low as 20 mT.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

High power tests of dressed supconducting 1.3 GHz RF cavities

A single-cavity test cryostat is used to conduct pulsed high power RF tests of superconducting 1.3 GHz RF cavities at 2 K. The cavities under test are welded inside individual helium vessels and are outfitted ('dressed') with a fundamental power coupler, higher-order mode couplers, magnetic shielding, a blade tuner, and piezoelectric tuners. The cavity performance is evaluated in terms of accelerating gradient, unloaded quality factor, and field emission, and the functionality of the auxiliary components is verified. Test results from the first set of dressed cavities are presented here.

43 PARTICLE ACCELERATORS↗

Microwave power coupler for a superconducting multiple-cell cavity for accelerator application and its testing procedures

Superconducting cavity resonators offer the advantage of high field intensity for a given input power, making them an attractive contender for particle accelerator applications. Power coupling into a superconducting cavity employed in a particle accelerator requires unique provisions to maintain high vacuum and cryogenic temperature on the cavity side, while operating with ambient conditions on the source side. Components introduced to fulfill mechanical requirements must show negligible obstruction of the propagation of the microwave with absence of critical locations that may give rise to electron multipaction, leading to a multiple section design, instead of an aperture, a probe, or a loop structure as found in conventional cavities. A coaxial power coupler for a superconducting multiple-cell cavity at 3.9 GHz has been developed. The cavity is intended to be employed as an accelerator to provide enhanced electron beam quality in a free-electron laser in Hamburg (FLASH) user facility. The design of the coupler called for two windows to sustain high vacuum in the cavity and two bellows to accommodate mechanical dimensional changes resulting from cryogenics. Suppression of multipacting was accomplished by the choice of conductor dimensions and materials with low second yield coefficients. Prior to integration with the cavity, the coupler was tested for intrinsic properties in a back-to-back configuration and conditioned for high-power operation with increasing power input. Maximum incident power was measured to be 61 kW. When integrated with the superconducting cavity, a loaded quality factor of 9 x 10 5 was measured by transient method. Coupler return loss and insertion loss were estimated to be around -21 dB and -0.2 dB, respectively.

43 PARTICLE ACCELERATORS↗

Superconducting Coplanar Waveguide Resonators Capable of Cofabrication with Josephson Junctions

Superconducting coplanar waveguide resonators and Josephson junctions are crucial components of superconducting quantum information processing chips. Resonators are usually fabricated through lift-off or etching, while Josephson junctions are made by trilayer process or double-angle evaporation. To simplify the fabrication process, we propose a scheme that uses the same process steps for both Josephson junctions and resonators. Simulations and experiments are conducted to confirm that resonators fabricated via the proposed process have quality factor comparable to those via traditional process. This work paves the way for quantum information processing on superconducting large-scale integrated circuits.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Suppression of four-wave mixing in a 22 × 10 Gbps dense wavelength division multiplexed system by linearly chirped fiber Bragg gratings

A scheme comprising two linearly chirped fiber Bragg gratings (LCFBGs) is proposed to suppress four-wave mixing (FWM) effects in a 22×10 Gbps dense wavelength division multiplexed (DWDM) system employing dispersion shifted fiber with 0.2 nm channel spacing. The FWM reduction in our proposed scheme has been studied by varying the input signal power per channel from − 2 to + 10 dBm. The parameters of LCFBGs are optimized to obtain a maximum quality factor for all 22 channels. The proposed method is effective even at high input power (10 dBm) and provides a simple, cost effective way to improve the transmission performance in DWDM system.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Coherent-state storage and retrieval between superconducting cavities using parametric frequency conversion

In superconducting quantum information, machined aluminum superconducting cavities have proven to be a well-controlled, low-dissipation electromagnetic environment for quantum circuits such as qubits. They can possess large internal quality factors, Q{sub int} > 10{sup 8}, and present the possibility of storing quantum information for times far exceeding those of microfabricated circuits. However, in order to be useful as a storage element, these cavities require a fast “read/write” mechanism—in other words, they require tunable coupling between other systems of interest such as other cavity modes and qubits, as well as any associated readout hardware. In this work, we demonstrate these qualities in a simple dual cavity architecture in which a low-Q “readout” mode is parametrically coupled to a high-Q “storage” mode, allowing us to store and retrieve classical information. Specifically, we employ a flux-driven Josephson junction-based coupling scheme to controllably swap coherent states between two cavities, demonstrating full, sequenced control over the coupling rates between modes.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Sintering behaviors, phases, and dielectric properties of MO-TeO2-V2O5 (M = Ca, Sr, Ba) ultralow temperature ceramics

Highlights: • Introduction of TeO{sub 2} to MO-V{sub 2}O{sub 5} (M = Ca,Sr,Ba) ceramics promoted a M{sub 2}V{sub 2}O{sub 7} phase formation, and obtain excellent dielectric properties and a densification sintering at below 600°. • Chemical compatibility of ULTCC ceramics with aluminum electrode indicated that aluminum did not react with MO-TeO{sub 2}-V{sub 2}O{sub 5} ceramics. • Aluminum easily encouraged the transformation of M{sub 2}V{sub 2}O{sub 7} structures to M{sub 3}(VO{sub 4}){sub 2} structures and other structures under the ultra-low temperature sintering. - Abstract: Influences of TeO{sub 2} on phase evolutions and sintering behaviors of MO-TeO{sub 2}-V{sub 2}O{sub 5} (M = Ca, Sr, Ba) ultralow temperature ceramics were investigated using X-ray diffraction (XRD) and scanning electron microscopy (SEM). Dielectric properties of MO-TeO{sub 2}-V{sub 2}O{sub 5} (M = Ca, Sr, Ba) ceramics and their chemical compatibility with an aluminum electrode were also studied. Introducing TeO{sub 2} to MO-V{sub 2}O{sub 5} (M = Ca, Sr, Ba) ceramics obviously decreased the sintering temperature and promoted formation of M{sub 2}V{sub 2}O{sub 7} (M = Ca, Sr, Ba) phases. Also, dielectric properties mainly depend on the amount of TeO{sub 2} added to MO-TeO{sub 2}-V{sub 2}O{sub 5} ceramics. Investigation of chemical compatibility with aluminum shows that aluminum does not react chemically with MO-TeO{sub 2}-V{sub 2}O{sub 5} ceramics; however, aluminum causes transformation of M{sub 2}V{sub 2}O{sub 7} phases to other phases (such as M{sub 3}(VO{sub 4}){sub 2}) to be easier. Sintering temperature of MO-TeO{sub 2}-V{sub 2}O{sub 5} (M = Ca, Sr, Ba) ceramics can be regulated below 600 °C, which is much less than the melting point of aluminum. In addition, MO-TeO{sub 2}-V{sub 2}O{sub 5} (M = Ca, Ba) ceramics maintain quality factors of ∼18,000 GHZ, a dielectric constant of 10–12, and dielectric loss lower than 10{sup −4}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Moment-based, self-consistent linear analysis of gyrotron oscillators

A new model for simulating gyrotron oscillators in the monomode time-dependent linear self-consistent regime is presented. Starting from a nonlinear time-dependent monomode model, the linearization and the following simplification of the model, based on a moment approach, are described. This simplified model represents a numerically efficient model and allows to have a deeper physical insight, in particular, for regimes dominated by self-consistent effects such as for the gyro-backward wave instability. One specific case of a gyrotron cavity is studied in detail and compared with experimental results, with special attention to self-consistent effects and to the differences with a model using a fixed field profile. Self-consistent linear simulations are, amongst other applications, important for the design of frequency-tunable gyrotrons or high-power gyrotrons with cavities having a relatively low quality factor, but also for studies of parasitic oscillations as they may occur in beam ducts and/or in the launcher section following the interaction cavity.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Five-cell superconducting RF module with a PBG coupler cell: design and cold testing of the copper prototype

We report the design and experimental data for a copper prototype of a superconducting radio-frequency (SRF) accelerator module. The five-cell module has an incorporated photonic band gap (PBG) cell with couplers. The purpose of the PBG cell is to achieve better higher order mode (HOM) damping, which is vital for preserving the quality of high-current electron beams. Better HOM damping raises the current threshold for beam instabilities in novel SRF accelerators. The PBG design also increases the real-estate gradient of the linac because both HOM damping and the fundamental power coupling can be done through the PBG cell instead of on the beam pipe via complicated end assemblies. First, we will discuss the design and accelerating properties of the structure. The five-cell module was optimized to provide good HOM damping while maintaining the same accelerating properties as conventional elliptical-cell modules. We will then discuss the process of tuning the structure to obtain the desired accelerating gradient profile. Finally, we will list measured quality factors for the accelerating mode and the most dangerous HOMs.

43 PARTICLE ACCELERATORS↗

Heat load of a P-doped GaAs photocathode in SRF electron gun

Many efforts were made over the last decades to develop a better polarized electron source for the high energy physics. Several laboratories operate DC guns with the Gallium-Arsenide photo-cathode, which yield a highly polarized electron beam. However, the beam's emittance might well be improved using a Superconducting RF electron gun, which delivers beams of higher brightness than DC guns does, because the field gradient at the cathode is higher. SRF guns with metal cathodes and CsTe cathodes have been tested successfully. To produce polarized electrons, a Gallium-Arsenide photo-cathode must be used: an experiment to do so in a superconducting RF gun is under way at BNL. Since the cathode will be normal conducting, the problem about the heat load stemming from the cathode arises. We present our measurements of the electrical resistance of GaAs at cryogenic temperatures, a prediction of the heat load and the verification by measuring the quality factor of the gun with and without cathode.

43 PARTICLE ACCELERATORS↗

A new proposal for a high-performance 4-channel demultiplexer based on 2D photonic crystal using three cascaded ring resonators for applications in advanced optical systems

In this paper, a high-performance 4-channel demultiplexer (DEMUX) based on 2D photonic crystal using three cascaded ring resonators is proposed. The proposed DEMUX is composed of square lattice of silicon dielectric rods with a refractive index of 3.46 suspended in air. For the proposed device, the lattice constant a = 590 nm and the filling factor r/a = 0.2. In this study, the plane wave expansion and finite-difference time-domain methods are used respectively to characterize the photonic band gap and to investigate the optical behaviour of the structure. It is demonstrated that by choosing appropriate values for the radius of the inner rods, scattering rods, coupling rods and the coupling length between the bus and the drop waveguides, the desired wavelengths can effectively be separated. The resonant wavelengths of the proposed DEMUX are 1528.7 nm, 1535.3 nm, 1531 nm, and 1533 nm. The mean quality factor, spectral bandwidth and the transmission efficiency of our device are computed to be respectively 7358.5, 0.217 nm and 99.25%. The proposed DEMUX has a mean channel spacing, minimum and maximum values of crosstalk of about 2.2 nm, − 46.68 dB and − 9.79 dB, respectively. Furthermore, the footprint of the device is 294.4 μm{sup 2}, which is suitable for photonic integrated circuits.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

High quality SiC microdisk resonators fabricated from monolithic epilayer wafers

The exquisite mechanical properties of SiC have made it an important industrial material with applications in microelectromechanical devices and high power electronics. Recently, the optical properties of SiC have garnered attention for applications in photonics, quantum information, and spintronics. This work demonstrates the fabrication of microdisks formed from a p-N SiC epilayer material. The microdisk cavities fabricated from the SiC epilayer material exhibit quality factors of as high as 9200 and the approach is easily adaptable to the fabrication of SiC-based photonic crystals and other photonic and optomechanical devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ultrastable laser system for spectroscopy of the {sup 1}S{sub 0}–{sup 3}P{sub 0} clock transition in Sr atoms

A laser system with a spectral linewidth less than 1 Hz for spectroscopy of the {sup 1}S{sub 0}–{sup 3}P{sub 0} clock transition in strontium atoms has been demonstrated. A semiconductor laser emitting at a wavelength of 698 nm was stabilised to an external high-finesse Fabry–Perot cavity with vibration and temperature compensation near the zero expansion point. After laser cooling to a temperature below 3 μK, {sup 88}Sr atoms were loaded into an optical lattice at a magic wavelength of 813 nm. The laser system was used to characterise the {sup 88}Sr clock transition by magnetically induced spectroscopy. The resonance spectral width was determined to be 130 ± 17 Hz, which corresponds to a quality factor of 3 × 10{sup 12}. (paper)

74 ATOMIC AND MOLECULAR PHYSICS↗

Cryogenic test of double quarter wave crab cavity for the LHC High luminosity upgrade

A Proof-of-Principle (PoP) Double Quarter Wave Crab Cavity (DQWCC) was designed and fabricated for the Large Hadron Collider (LHC) luminosity upgrade. A vertical cryogenic test has been done at Brookhaven National Lab (BNL). The cavity achieved 4.5 MV deflecting voltage with a quality factor above 3×10 9 . We report the test results of this design.

43 PARTICLE ACCELERATORS↗

Trends of microwave dielectric materials for antenna application

Rapid development of a modern microwave communication system requires a high quality microwave dielectric ceramic material to be used as mobile and satellite communication. High permittivity of dielectric ceramics leads to fabrication of compact device for electronic components. Dielectric ceramics which used for microwave applications required three important parameters such as high or appropriate permittivity (ε{sub r}), high quality factor (Q {sub f} ≥ 5000 GH z) and good temperature coefficient of resonant frequency (τ{sub f}). This paper review of various dielectric ceramic materials used as microwave dielectric materials and related parameters for antenna applications.

36 MATERIALS SCIENCE↗

Effect of ripple taper on band-gap overlap in a coaxial Bragg structure operating at terahertz frequency

Based on the mode-coupling method, numerical analysis is presented to demonstrate the influence of ripple taper on band-gap overlap in a coaxial Bragg structure operating at terahertz frequency. Results show that the interval between the band-gaps of the competing mode and the desired working mode is narrowed by use of positive-taper ripples, but is expanded if negative-taper ripples are employed, and the influence of the negative-taper ripples is obviously more advantageous than the positive-taper ripples; the band-gap overlap of modes can be efficiently separated by use of negative-taper ripples. The residual side-lobes of the frequency response in a coaxial Bragg structure with ripple taper also can be effectively suppressed by employing the windowing-function technique. These peculiarities provide potential advantage in constructing a coaxial Bragg cavity with high quality factor for single higher-order-mode operation of a high-power free-electron maser in the terahertz frequency range.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

High-Q silicon carbide photonic-crystal cavities

We demonstrate one-dimensional photonic-crystal nanobeam cavities in amorphous silicon carbide. The fundamental mode exhibits intrinsic optical quality factor as high as 7.69 × 10{sup 4} with mode volume ∼0.60(λ/n){sup 3} at wavelength 1.5 μm. A corresponding Purcell factor value of ∼10{sup 4} is the highest reported to date in silicon carbide optical cavities. The device exhibits great potential for integrated nonlinear photonics and cavity nano-optomechanics.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗