Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Pressure effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Thermodynamic origin of the pressure-induced Invar effect: General criterion and experimental study of Fe 68 ⁢Pd 32

Synchrotron X-ray diffraction measurements were performed on 57 Fe 68 Pd 32 at multiple pressures and two temperatures in a diamond-anvil cell. Between 4 and 11GPa, the thermal expansion was zero or slightly negative. This pressure-induced Invar effect was studied further with 57 Fe nuclear forward scattering and nuclear resonant inelastic X-ray scattering to obtain information on the pressure-induced changes in both the magnetization and the phonon density of states. Magnetic entropy and phonon entropy were obtained from these results, the latter with additional measurements from inelastic neutron scattering to account for the contributions from Pd atoms. The dependencies of these entropies on pressure gave the magnetic and phonon contributions to thermal expansion. These canceled in the region of pressure-induced Invar behavior, even though they individually increased by more than a factor of 2 below the Curie pressure. The behavior of phonons gives evidence for spin-phonon interactions in Fe 68 Pd 32 . A general explanation of the pressure-induced Invar effect is presented, showing that Invar behavior is typically expected at a pressure P* below a magnetic transition at pressure PC. The difference in pressure P C − P* scales with the fractional reduction in magnetic exchange interaction divided by the average Gr¨uneisen parameter.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Cost analysis of alternative large-scale high-temperature solid oxide electrolysis hydrogen production facilities

We extend our past cost analysis of gigawatt-scale solid oxide electrolysis (SOE) facilities that produce high purity hydrogen gas from water by estimating construction and operating costs for three new alternative design cases: (1) offsite feed steam generation; (2) near-atmospheric pressure (NAP) stack; and (3) onsite electric boiler feed steam generation. Pressure effects on hydrogen electrode-(cathode-)supported SOE cell (SOEC) stack performance are estimated for the same assumed cell and stack construction and used to determine facility-wide stack capital costs for achieving a fixed H2 production at different pressures. Modular balance of plant (BOP) process equipment capital costs are estimated for each new alternative design case using our past equipment sizing, design, and cost data and scaling relationships. Furthermore, we update BOP equipment sizing and design for the NAP case using Aspen®. Vendor quotes for electric boilers are used to estimate costs for the electric boiler design case. Factory and onsite assembly and installation costs for SOEC stacks and BOP equipment are calculated using our past simplified first-principles approach. First-of-a-kind (FOAK) and N th -of-a-kind (NOAK) production maturity cost estimates are included for all results. The case with NAP stacks offers the lowest facility total capital cost (TCC, ~23% lower than base) while use of small electric boilers requires the highest TCC (~3% higher than base). H 2 production prices decrease from the base of ~$\$2.17$ /kgH 2 to ~$\$1.92$/kgH 2 for 1 GW e DC SIP facilities utilizing NAP stacks supplied by offsites steam situated in large modules and blocks for $\$0.030$/kWh e and $0.009/kWh t prices for electricity and thermal energy, respectively. We report all costs in 2021 US dollars.

Balance of plant (BOP) process equipment↗
NASA NTRS2016

Plasma Oscillation Characterization of NASA's HERMeS Hall Thruster via High Speed Imaging

The performance and facility effect characterization tests of NASA's 12.5-kW Hall Effect Rocket with Magnetic Shielding had been completed. As a part of these tests, three plasma oscillation characterization studies were performed to help determine operation settings and quantify margins. The studies included the magnetic field strength variation study, background pressure effect study, and cathode flow fraction study. Separate high-speed videos of the thruster including the cathode and of only the cathode were recorded. Breathing mode at 10-15 kHz and cathode gradient-driven mode at 60-75 kHz were observed. An additional high frequency (40-70 kHz) global oscillation mode with sinusoidal probability distribution function was identified.

Ground Tests↗
NASA NTRS2014

A Novel Method for Estimating Shortwave Direct Radiative Effect of Above-Cloud Aerosols Using CALIOP and MODIS Data

This paper describes an efficient and unique method for computing the shortwave direct radiative effect (DRE) of aerosol residing above low-level liquid-phase clouds using CALIOP and MODIS data. It accounts for the overlapping of aerosol and cloud rigorously by utilizing the joint histogram of cloud optical depth and cloud top pressure. Effects of sub-grid scale cloud and aerosol variations on DRE are accounted for. It is computationally efficient through using grid-level cloud and aerosol statistics, instead of pixel-level products, and a pre-computed look-up table in radiative transfer calculations. We verified that for smoke over the southeast Atlantic Ocean the method yields a seasonal mean instantaneous shortwave DRE that generally agrees with more rigorous pixel-level computation within 4. We have also computed the annual mean instantaneous shortwave DRE of light-absorbing aerosols (i.e., smoke and polluted dust) over global ocean based on 4 yr of CALIOP and MODIS data. We found that the variability of the annual mean shortwave DRE of above-cloud light-absorbing aerosol is mainly driven by the optical depth of the underlying clouds.

radiative forcing↗
NASA NTRS2013

A Novel Method for Estimating Shortwave Direct Radiative Effect of Above-cloud Aerosols over Ocean Using CALIOP and MODIS Data

This paper describes an efficient and unique method for computing the shortwave direct radiative effect (DRE) of aerosol residing above low-level liquid-phase clouds using CALIOP and MODIS data. It accounts for the overlapping of aerosol and cloud rigorously by utilizing the joint histogram of cloud optical depth and cloud top pressure. Effects of sub-grid scale cloud and aerosol variations on DRE are accounted for. It is computationally efficient through using grid-level cloud and aerosol statistics, instead of pixel-level products, and a pre-computed look-up table in radiative transfer calculations. We verified that for smoke over the southeast Atlantic Ocean the method yields a seasonal mean instantaneous shortwave DRE that generally agrees with more rigorous pixel-level computation within 4%. We have also computed the annual mean instantaneous shortwave DRE of light-absorbing aerosols (i.e., smoke and polluted dust) over global ocean based on 4 yr of CALIOP and MODIS data. We found that the variability of the annual mean shortwave DRE of above-cloud light-absorbing aerosol is mainly driven by the optical depth of the underlying clouds.

CALIOP and MODIS↗
DOE OSTI2023

Pressure-Dependent Magnetic Properties of Quasi-2D Cr 2 Si 2 Te 6 and Mn 3 Si 2 Te 6

Recently, pressure has been used to induce structural and magnetic phase transitions in many layered quantum materials whose layers are linked by van der Waals forces. Materials with such weakly held layers allow for relatively easy manipulation of the superexchange mechanism, which can give rise to novel magnetic behavior. Here, using hydrostatic pressure as a disorderless means to manipulate the interlayer coupling, we applied pressure on two quasi-2D sister compounds, namely, Cr 2 Si 2 Te 6 (CST) and Mn 3 Si 2 Te 6 (MST), up to ~1 GPa. Magnetic property measurements with the application of pressure revealed that the ferromagnetic transition temperature decreases in CST, while the opposite occurs for the ferrimagnetic MST. In MST, magnetization decreases with the increase in pressure, and such a trend is not clearly observed within the pressure range studied for CST. The overall pressure effect on magnetic characteristics such as exchange couplings and magnetic anisotropy energies is also examined theoretically using density functional theory. Exchange coupling in MST is strongly frustrated, and the first nearest neighbor interaction is the most dominant of the components with the strongest pressure dependence. In CST, the exchange coupling parameters exhibit very little dependence on pressure. This combined experimental and theoretical work has the potential to expand to other relevant quantum materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1945

Effect of Maximum Cruise-power Operation at Ultra-lean Mixture and Increased Spark Advance on the Mechanical Condition of Cylinder Components

A continuous 50-hour test was conducted to determine the effect of maximum cruise-power operation at ultra-lean fuel-air mixture and increased spark advance on the mechanical conditions of cylinder components. The test was conducted on a nine-cylinder air-cooled radial engine at the following conditions:brake horsepower, 750; engine speed, 1900 rpm; brake mean effective pressure, 172 pounds per square inch; fuel-air ratio, 0.052; spark advance, 30 deg B.T.C.; and maximum rear-spark-plug-bushing temperature, 400 F. In addition to the data on corrosion and wear, data are presented and briefly discussed on the effect of engine operation at the conditions of this test on economy, knock, preignition, and mixture distribution. Cylinder, piston, and piston-ring wear was small and all cylinder component were in good condition at the conclusion of the 50-hour test except that all exhaust-valve guides were bellmouthed beyond the Army's specified limit and one exhaust-valve face was lightly burned. It is improbable that the light burning in one spot of the valve face would have progressed further because the burn was filled with a hard deposit so that the valve face formed an unbroken seal and the mating seat showed no evidence of burning. The bellmouthing of the exhaust-valve guides is believed to have been a result of the heavy carbon and lead-oxide deposits, which were present on the head end of the guided length of the exhaust-valve stem. Engine operational the conditions of this test was shown to result In a fuel saving of 16.8 percent on a cooled-power basis as compared with operation at the conditions recommended for this engine by the Army Air Forces for the same power.

ENGINE CYLINDERS-WEAR↗
DOE OSTI2023

Unraveling Emergent Quantum States in Magnetic Topological Insulators using High Pressure Neutron Scattering

This proposal aims to uncover novel quantum phenomena under high pressure and understand the pressure effects on the atomic electronic interactions in magnetic topological materials. This program supports a combined neutron scattering and materials discovery of novel magnetic materials that display the coexistence of magnetism plus other physical phenomena such as a non-trivial electronic band topology under high pressure. The goal of this project is to close a long-standing knowledge gap in quantum materials research by developing a high-pressure neutron scattering (HP-NS) toolbox to systematically determine the magnetic structures and electronic interactions present at high pressure.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

The Effect of Spark-Plug Heat Dispersal Range and Exhaust Valve Opening Timing on Cold-Start Emissions and Cycle-to-Cycle Variability

The partnership for advancing combustion engines (PACE) is a US Department of Energy consortium involving multiple national laboratories and includes a goal of addressing key efficiency and emission barriers in light-duty engines fueled with a market-representative E10 gasoline. A major pillar of the initiative is the generation of detailed experimental data and modeling capabilities to understand and predict cold-start behavior. Cold-start, as defined by the time between first engine crank and three-way catalyst light-off, is responsible for a large percentage of NOx, unburned hydrocarbon and particulate matter emissions in light-duty engines. Minimizing emissions during cold-start is a trade-off between achieving faster light-off of the three-way catalyst and engine out emissions during that period. In this study, gaseous and soot emissions were measured at a distance representative of the three-way catalyst position downstream of the engine at a 2 bar net indicated mean effective pressure (NIMEP) steady-state operating condition representative of cold-start. The test matrix included sweeps of ignition timing 15 degrees-before to 10 degrees-after top dead center firing (TDCf) across three different spark-plug heat dispersal ranges (HR). Additionally, the effect of varying exhaust valve opening (EVO) timing on combustion stability and emissions was also studied. Results show that the spark plug HR affects the coefficient of variation (COV) of NIMEP under all cold-start conditions, while the impact on emissions was found to be minimal. At very retarded spark timings, colder spark plugs required higher air and fuel flow to maintain the desired 2bar NIMEP load, but the fraction of fuel energy going into the exhaust was found to be similar for all spark plugs. Finally, retarding exhaust valve timings showed a simultaneous reduction in emissions while increasing the fraction of fuel energy being fed into the exhaust. However, engine COV was also observed to increase with retarded exhaust timings.

42 ENGINEERING↗
NASA NTRS1995

Unusual locations of Earth's bow shock on September 24 - 25, 1987: Mach number effects

International Sun Earth Explorer 1 (ISEE 1) and Interplanetary Monitoring Platform 8 (IMP 8) data are used to identify 19 crossings of Earth's bow shock during a 30-hour period following 0000 UT on September 24, 1987. Apparent standoff distances for the shock are calculated for each crossing using two methods and the spacecraft location; one method assumes the average shock shape, while the other assumes a ram pressure-dependent shock shape. The shock's apparent standoff distance, normally approximately 14 R(sub E), is shown to increase from near 10 R(sub E) initially to near 19 R(sub E) during an 8-hour period, followed by an excursion to near 35 R(sub E) (where two IMP 8 shock crossings occur) and an eventual return to values smaller than 19 R(sub E). The Alfven M(sub A) and fast magnetosonic M(sub ms). Mach numbers remain above 2 and the number density above 4/cu cm for almost the entire period. Ram pressure effects produce the initial near-Earth shock location, whereas expansions and contractions of the bow shock due to low Mach number effects account, qualitatively and semiquantitatively, for the timing and existence of almost all the remaining ISEE crossings and both IMP 8 crossings. Significant quantitative differences exist between the apparent standoff distances for the shock crossings and those predicted using the observed plasma parameters and the standard model based on Spreiter et al.'s (1966) gasdynamic equation. These differences can be explained in terms of either a different dependence of the standoff distance on Mach number at low M(sub A) and M(sub ms), or variations in shock shape with M(sub A) and M(sub ms) (becoming increasingly "puffed up" with decreasing M(sub A) and M(sub ms), as expected theoretically), or by a combination of both effects.

Cairns, Iver H.↗
DOE OSTI2020

Pressure-Induced Dimerization of C 60 at Room Temperature as Revealed by an In Situ Spectroscopy Study Using an Infrared Laser

Using in situ high-pressure Raman spectroscopy and X-ray diffraction, the polymerization and structure evaluation of C 60 were studied up to 16 GPa at room temperature. The use of an 830 nm laser successfully eliminated the photo-polymerization of C 60 , which has interfered with the pressure effect in previous studies when a laser with a shorter wavelength was used as excitation. It was found that face-centered cubic (fcc) structured C 60 transformed into simple cubic (sc) C 60 due to the hint of free rotation for the C 60 at 0.3 GPa. The pressure-induced dimerization of C 60 was found to occur at about 3.2 GPa at room temperature. Our results suggest the benefit and importance of the choice of the infrared laser as the excitation laser.

36 MATERIALS SCIENCE↗
NASA NTRS1973

Rates and mechanisms of the atomic oxygen reaction with nickel at elevated temperatures

The oxidation of nickel by atomic oxygen at pressure from 1 to 45 N/sq m between 1050 and 1250 K was investigated. In these ranges, the oxidation was found to follow the parobolic rate law, viz., K sub p = 0.0000114 exp(-13410/T) g squared/cm4/sec for films of greater than 1 micron thickness and was pressure independent. The activation enthalpy for the oxidation reaction was 112 + or - 11 kj/mole (27 + or - 3 kcal/mole). Of a number of possible mechanisms and defect structures considered, it was shown that the most likely was a saturated surface defect model for atomic oxidation, based on reaction activation enthalpies, impurity effects, pressure independence, and magnitudes of rates. A model judged somewhat less likely was one having doubly ionized cationic defects rate controlling in both atomic and molecular oxygen. From comparisons of the appropriate processes, the following enthalpy values were derived: enthalpy of activation (Ni diffusion in Ni0) = 110 + or - 30 kj/mole and standard enthalpy change for reaction formation (doubly ionized cation vacancies in Ni0 from atomic oxygen)= -9 + or - 25 kj/mole.

Christian, J. D.↗
DOE OSTI2024

Evaluation of the Performance and Exhaust Emissions of a 4 Cylinder CI Engine Operating With Dimethyl Ether (DME) and Propane Blends

In response to stringent emissions regulations and the need for higher efficiency engines, the utilization of DME and propane fuel blends in compression ignition (CI) engines has gained interest in the automotive industry. In this study, a range of DME-propane blends are explored in a CI combustion strategy at high injection pressures. A GT-Power model of a 2.2 L Hyundai CI engine was developed to facilitate evaluation of the impacts of variations of DME and propane blends at a light and medium engine speed-torque-load operating condition; specifically at 1500 rpm, 50 Nm and 2.84 bar brake mean effective pressure (BMEP); and 2000 rpm, 150 Nm, 8.53 bar BMEP speed-torque-load combination. Here, the GT-Power model was validated using Computational Fluid Dynamics (CFD) simulations. The results indicate that high diesel-like efficiencies can be achieved with a 100% DME mass substitution and up to 50% propane-DME blends could be implemented without a significant penalty on engine performance indicators. Significant brake specific nitrogen oxides (BSNOx) reductions were also observed along with reductions in carbon dioxide (CO2) and soot when leveraging these fuel blends.

computational fluid dynamics↗
NASA NTRSDate not supplied

TPSAS-NF1676L-30044-DND

The Clouds and the Earth's Radiant Energy System (CERES) project now has over 17 years accurately observed top-of-the-atmosphere (TOA) flux record for climate monitoring and diagnostic studies. The CERES FluxByCldTyp dataset, which contains cloud properties and radiative fluxes for 42 cloud types sorted by cloud top pressure and cloud optical depth, is used to investigate the clouds and their associated TOA (top-of-the-atmosphere) fluxes changes over the tropical area during ENSO events during the observed period. Unlike past studies, this study shows the impact of ENSO on cloud properties like optical depth, cloud top effective pressure and temperature and TOA LW and SW fluxes for each sub cloud type. The study reveals the detailed contributions from different cloud types for radiative characteristics during different regimes of ENSOs. This is especially important for very small net TOA radiative balance due to the cancellation of the fluxes from different cloud types. The dataset serves as a more stringent validation of climate models for cloud properties and radiative fluxes.

Sun, Moguo↗
NASA NTRSDate not supplied

ENSO Tropical Cloud and TOA radiative signatures from the CERES observation

The Clouds and the Earth's Radiant Energy System (CERES) project now has over 15 years accurately observed top-of-the-atmosphere (TOA) flux record for climate monitoring and diagnostic studies. The CERES flux-by-cloud-type dataset, which contains cloud properties and radiative fluxes for 42 cloud types sorted by cloud top pressure and cloud optical depth, is used to investigate the clouds and their associated TOA (top-of-the-atmosphere) fluxes changes over the tropical area during ENSO events during the observed period. Unlike past studies, this study shows the impact of ENSO on cloud properties like optical depth, cloud top effective pressure and temperature and TOA LW and SW fluxes for each sub cloud type. The study reveals the detailed contributions from different cloud types for radiative characteristics during different phases of ENSO. This is especially important for very small net TOA radiative balance due to the cancellation of the fluxes from different cloud types. To further demonstrate the usefulness of this dataset, NCAR Community Atmosphere Model (CAM) is used to simulate the cloud and radiative changes during the period. The model cloud properties are converted to MODIS like cloud properties using modified MODIS simulator. The dataset serves as a more stringent validation of the model for cloud properties and radiative fluxes.

Moguo Sun↗
DOE OSTI2022

Modeling the hydrodynamic impact on the tool influence function during hemispherical subaperture optical polishing

To fabricate high-precision and accurate optics relative to the optical design surface, a high level of deterministic control of material removal (i.e., the tool influence function, TIF) during subaperture tool polishing is required. In this study, a detailed analysis of the pressure distribution, which is a key component of the TIF, has been performed using finite element analysis to couple together solid mechanics and fluid dynamics. Modeling experimental parameters of recently published work reveals that, when considering tool deformation, which in turn influences the fluid film thickness between the tool and workpiece, the effective pressure profile has a flat-top distribution. This flat-top pressure profile differs from the parabolic pressure distributions predicted by Hertzian mechanics. Furthermore, the shear contribution is shown here to be a key contributor to material removal, inducing the removal at the periphery of the contact edge and even outside the generally accepted contact area. Finally, the simulated fluid velocities provide evidence of mixed-mode contact polishing, supporting recent experimental findings that also suggest that onset of hydroplaning contributions lead to material removal drop-off.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Superconductivity and electron-phonon interaction in Sr x Bi 2 Se 3 under pressure

Pressure-induced superconductivity has been widely explored and observed in Bi 2 Se 3 -based topological materials to hunt for topological superconductors. Although their triggered superconductivity has a close connection to their pressure-induced structural phase transitions, the quest for the electron pairing mechanism of these superconducting semiconductors in both their initial rhombohedral and high-pressure phases remains unknown. In this work, we present a systematic study of the pressure effect on superconducting properties and lattice dynamics using a combination of electrical transport, Raman-scattering, and synchrotron x-ray diffraction measurements using diamond anvil cells. One key finding is our observation of a cooperative connection between the strength of the electron–phonon interaction (EPI) generated by optical branches and the pressure-tunable superconductivity in rhombohedral Sr x Bi 2 Se 3 crystal. The underlying suppression mechanism of the T c by pressure is ascribed to the weakening of the electrons' interaction with the optical phonon modes in the rhombohedral phase. In the intermediate monoclinic phase, the T c value underwent a sharp increase with carrier density accumulation accompanying the concurrent enhanced EPI. This is intuitively unusual since it is expected that the EPI shall be weakened by inducing more conducting carriers in a normal metal. In the tetragonal phase, the superconductivity is interpreted within BCS theory, since it is fully metallized and obeys the adiabatic Born–Oppenheimer approximation well. Our findings are important to fully understand unconventional superconductivity and the unusual pairing mechanism in the layered rhombohedral Bi 2 Se 3 -based superconductors.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗