Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ORBIT DECAY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Cosmological investigations from SIRTF

An overview is presented of the Space Infrared Telescope Facility (SIRTF), a one-meter-class cryogenically-cooled observatory for IR astronomy from space that will be the IR component of NASA's family of Great Observatories. SIRTF will operate at an altitude of 100,000 km and achieve its five year lifetime without the complication of on-orbit cryogenic replenishment and have twice the on-target efficiency that could be realized in LEO. The observations will permit the development of a direct empirical picture of the time evolution of cosmic phenomena, such as evolution of the chemical and stellar content of galaxies and the growth and decay of the quasar population.

Werner, M.↗
NASA NTRS2008

Supersonic/Hypersonic Laminar Heating Correlations for Rectangular and Impact-Induced Open and Closed Cavities

Impact and debris damage to the Space Shuttle Orbiter Thermal Protection System tiles is a random phenomenon, occurring at random locations on the vehicle surface, resulting in random geometrical shapes that are exposed to a definable range of surface flow conditions. In response to the 2003 Final Report of the Columbia Accident Investigation Board, wind tunnel aeroheating experiments approximating a wide range of possible damage scenarios covering both open and closed cavity flow conditions were systematically tested in hypersonic ground based facilities. These data were analyzed and engineering assessment tools for damage-induced fully-laminar heating were developed and exercised on orbit. These tools provide bounding approximations for the damaged-surface heating environment. This paper presents a further analysis of the baseline, zero-pressure-gradient, idealized, rectangular-geometry cavity heating data, yielding new laminar correlations for the floor-averaged heating, peak cavity endwall heating, and the downstream decay rate. Correlation parameters are derived in terms of cavity geometry and local flow conditions. Prediction Limit Uncertainty values are provided at the 95%, 99% and 99.9% levels of significance. Non-baseline conditions, including non-rectangular geometries and flows with known pressure gradients, are used to assess the range of applicability of the new correlations. All data variations fall within the 99% Prediction Limit Uncertainty bounds. Importantly, both open-flow and closed-flow cavity heating are combined into a single-curve parameterization of the heating predictions, and provide a concise mathematical model of the laminar cavity heating flow field with known uncertainty.

Everhart, Joel L.↗
NASA NTRS2016

Magnetospheric Multiscale Mission Attitude Dynamics: Observations from Flight Data

The NASA Magnetospheric Multiscale mission, launched on Mar. 12, 2015, is flying four spinning spacecraft in highly elliptical orbits to study the magnetosphere of the Earth. Extensive attitude data is being collected, including spin rate, spin axis orientation, and nutation rate. The paper will discuss the various environmental disturbance torques that act on the spacecraft, and will describe the observed results of these torques. In addition, a slow decay in spin rate has been observed for all four spacecraft in the extended periods between maneuvers. It is shown that this despin is consistent with the effects of an additional disturbance mechanism, namely that produced by the Active Spacecraft Potential Control devices. Finally, attitude dynamics data is used to analyze a micrometeoroid/orbital debris impact event with MMS4 that occurred on Feb. 2, 2016.

Conjunction↗
NASA NTRS2017

Minimum dV for Targeted Spacecraft Disposal

The density scale height of the Earth's atmosphere undergoes significant reduction in the final phases of a natural decay. It can be shown that for most realistic ballistic numbers, it is possible to exploit this effect to amplify available spacecraft dV by using it at the penultimate perigee to penetrate into higher drag regions at final apogee. The drag at this lower pass can more effectively propel a spacecraft towards the final target region than applying the same dV direct Hohmann transfer at that final apogee. This study analyzes the potential use of this effect-- in combination with small phasing burns--to calculate the absolute minimum delta-V that would be required to reliably guide a spacecraft to any specified safe unoccupied ocean region as a function of ballistic number, orbit inclination, and initial eccentricity. This calculation is made for controllable spacecraft in several orbit inclinations and eccentricities with arbitrary initial LAN and ArgP one week before final entry, under three-sigma atmospheric perturbations. The study analyzes the dV required under varying levels of final controllable altitude at which dV may be imparted, and various definitions of the length and location of a "safe" disposal area. The goal of such research is to improve public safety by creating assured safe disposal strategies for low-dV and/or low-thrust spacecraft that under more traditional strategies would need to be abandoned to a fully random decay.

Bacon, John↗
NASA NTRS1994

ASCA measurements of the grain-scattered X-ray halos of eclipsing massive X-ray binaries: Vela X-1 and Centaurus X-3

We have measured the decaying dust-scattered X-ray halo of Cen X-3 during its binary eclipse with the ASCA solid-state imaging spectrometer (SIS). The surface brightness profile (SBP) of the image in the low-energy band (0.5-3 keV) lies substantially above the point-spread function (PSF) of the X-ray telescope, while the SBP in the high-energy band (5-10 keV) exhibits no significant deviation. By contrast, the SBPs of Vela X-1 during its eclipse are consistent with the PSF in both the low- and high-energy bands -- strong evidence that a dust halo is indeed present in Cen X-3. Accordingly, we modeled the SBP of Cen X-3 taken from six consecutive time segments under the principal assumptions that the dust is distributed uniformly along a segment of the line of sight, the grains have a power-law size distribution, and the low-energy source flux was the same function of orbital phase before as during our observation. The best-fit set of parameters included a grain density value of 1.3 g/cu cm, substanially less than the density of 'astronomical silicate.' This result supports the idea that interstellar grains are 'fluffy' aggregates of smaller solid particles. We attribute the failure to detect a halo of Vela X-1 during its eclipse phase to extended strong circumsource absorption that probably occurred before the eclipse and allowed the halo to decay away before the observation began.

Woo, Jonathan W.↗
NASA NTRSDate not supplied

Monte Carlo simulations of neutrino and charged lepton propagation in the Earth with nuPyProp

An accurate modeling of neutrino flux attenuation and the distribution of leptons they produce in transit through the Earth is an essential component to determine neutrino flux sensitivities of underground, sub-orbital and space-based detectors. Through neutrino oscillations over cosmic distances, astrophysical neutrino sources are expected to produce nearly equal fluxes of electron, muon and tau neutrinos. Of particular interest are tau neutrinos that interact in the Earth at modest slant depths to produce leptons. Some leptons emerge from the Earth and decay in the atmosphere to produce extensive air showers. Future balloon-borne and satellite-based opticalCherenkov neutrino telescopes will be sensitive to upward air showers from tau neutrino induced lepton decays. We present nuPyProp, a python code that is part of the nuSpaceSim package. nuPyProp generates look-up tables for exit probabilities and energy distributions for (see paper for proper equation) propagation in the Earth. This flexible code runs with either stochastic or continuous electromagnetic energy losses for the lepton transit through the Earth. Current neutrino cross section models and energy loss models are included along with templates for user input of other models. Results from nuPyProp are compared with other recent simulation packages for neutrino and charged lepton propagation. Sources of modeling uncertainties are described and quantified.

Yosui Akaike↗
NASA NTRS1972

Technique for rapid determination of relative ages of lunar areas from orbital photography.

Development of a technique for determining relative ages of regions of the lunar surface from orbital photography using a model of small-impact erosion. The erosion model relates the shape of a crater to the integrated flux of debris that has impacted the surface since that crater was fresh. The shape of the most modified crater of a particular diameter is thereby related to the relative age of the surface. Application of this analysis to orbital photography reveals that the major mare units vary in the accumulation of impacts by more than a factor of 3. Comparison of these data with crystallization ages determined from samples collected during the Apollo 11 and 12 missions indicates that the impact fluxes were decreasing during the stages of mare formation. An exponentially decaying flux for the last 3.5 b.y. with a half-life of 0.6 to 1.4 b.y. is compatible with the data.

Soderblom, L. A.↗
NASA NTRS1979

HEAO 1 observations of the X-ray pulsar 4U 1626-67

Results are reported for an observation of the 7-s pulsar 4U 1626-67 with the A-2 experiment on HEAO 1. The phase-averaged X-ray spectrum between 0.7 and 60 keV is complex, as are the constituent spectra, which change radically as a function of pulse phase. Included in this spectral change is the sudden appearance and subsequent decay of a continuum or emission feature with a mean energy of 19 keV, which contains about one-half the power in this spectral range. Pulse-timing results include a new determination of the pulse period and a factor of 8 reduction in the upper limit for the light travel time for orbital periods between 1 and 7 hours. These findings are discussed and compared with the general nature of pulsar spectra.

Pravdo, S. H.↗
NASA NTRS2017

Relevance of Tidal Heating on Large TNOs

We examine the relevance of tidal heating for large Trans-Neptunian Objects, with a focus on its potential to melt and maintain layers of subsurface liquid water. Depending on their past orbital evolution, tidal heating may be an important part of the heat budget for a number of discovered and hypothetical TNO systems and may enable formation of, and increased access to, subsurface liquid water. Tidal heating induced by the process of despinning is found to be particularly able to compete with heating due to radionuclide decay in a number of different scenarios. In cases where radiogenic heating alone may establish subsurface conditions for liquid water, we focus on the extent by which tidal activity lifts the depth of such conditions closer to the surface. While it is common for strong tidal heating and long lived tides to be mutually exclusive, we find this is not always the case, and highlight when these two traits occur together. We find cases where TNO systems experience tidal heating that is a significant proportion of, or greater than radiogenic heating for periods ranging from100 s of millions to a billion years. For subsurface oceans that contain a small antifreeze component, tidal heating due to very high initial spin states may enable liquid water to be preserved right up to the present day. Of particular interest is the Eris-Dysnomia system, which in those cases may exhibit extant cryovolcanism.

Saxena, Prabal↗
NASA NTRS1989

Contamination effects of GPS Navstar solar array performance

The solar arrays on Navstars 1 to 6 have been limiting the electrical power capabilities in the extended life (beyond the 5 year design life). The departure from predicted performance consists of an extra 2.5 percent per year degradation beyond the radiation model estimates. This degradation is unusual in showing a linear rather than exponential decay with time. The performance of the arrays on these satellites has been examined in order to predict future behavior and to make refined projections on the Navstar 7 to 11 solar arrays. Evidence obtained from flight experiments on Navstar 5 and 6, and from laboratory experiments, suggests that contamination of the solar arrays while on orbit may be responsible. The evidence for photo-induced contamination of spacecraft surfaces is presented, and the effect on solar array output in the case of the GPS satellites is shown to be consistent with the observed anomalies.

Marvin, Dean C.↗
NASA NTRS2017

Spacecraft Re-Entry Impact Point Targeting Using Aerodynamic Drag

The ability to re-enter the atmosphere at a desired location is important for spacecraft containing components that may survive re-entry. While impact point targeting has traditionally been initiated through impulsive burns with chemical thrusters on large vehicles such as the Space Shuttle, and the Soyuz and Apollo capsules, many small spacecraft do not host thrusters and require an alternative means of impact point targeting to ensure that falling debris do not cause harm to persons or property. This paper discusses the use of solely aerodynamic drag force to perform this targeting. It is shown that by deploying and retracting a drag device to vary the ballistic coefficient of the spacecraft, any desired longitude and latitude on the ground can be targeted provided that the maneuvering begins early enough and the latitude is less than the inclination of the orbit. An analytical solution based on perturbations from a numerically propagated trajectory is developed to map the initial state and ballistic coefficient profile of a spacecraft to its impact point. This allows the ballistic coefficient profile necessary to reach a given target point to be rapidly calculated, making it feasible to generate the guidance for the decay trajectory onboard the spacecraft. The ability to target an impact point using aerodynamic drag will enhance the capabilities of small spacecraft and will enable larger space vehicles containing thrusters to save fuel by more effectively leveraging the available aerodynamic drag.

propagation↗
NASA NTRS1971

Study of energetic solar particle events of 18 November 1968, 25 February 1969, and 30 March 1969

The solar particle events of 18 November 1968, 25 February 1969, and 30 March 1969 were studied using data from the detector system aboard the lunar orbiting satellite Explorer 35. Protons, alpha particles, and Z or = 3 nuclei were registered in the solid state detector of the system. Interplanetary propagation, particle anisotropy, and the intensity ratios of protons to alpha particles and of alpha particles to C, N, and O nuclei above a common specific energy of 0.5 MeV/nucleon were studied. Diffusion coefficients and decay constants for the three events are given, as well as magnitudes and directions of anisotropies.

Venkatarangan, P.↗
NASA NTRS1988

Active region coronal loops - Structural and variability

X-ray images of a pair of active region loops are studied which show significant, short time-scale variability in the line fluxes of O VIII, Ne IX, and Mg XI and in the 3.5-11.5 keV soft X-ray bands. Vector magnetograms and high-resolution UV images were used to model the three-dimensional characteristics of the loops. X-ray light curves were generated spanning four consecutive orbits for both loops individually, and light curves of the loop tops and brightest points were also generated. The largest variations involve flux changes of up to several hundred percent on time scales of 10 minutes. No significant H-alpha flare activity is reported, and loop temperatures remain in the four to six million K range. The decay phases of the light curves indicate radiative cooling, inhibition of conduction, and some type of 'continued heating' due to ongoing, underlying activity at the microflare level.

Haisch, Bernhard M.↗
NASA NTRS2008

Radioisotope Power: A Key Technology for Deep Space Exploration

A Radioisotope Power System (RPS) generates power by converting the heat released from the nuclear decay of radioactive isotopes, such as Plutonium-238 (Pu-238), into electricity. First used in space by the U.S. in 1961, these devices have enabled some of the most challenging and exciting space missions in history, including the Pioneer and Voyager probes to the outer solar system; the Apollo lunar surface experiments; the Viking landers; the Ulysses polar orbital mission about the Sun; the Galileo mission to Jupiter; the Cassini mission orbiting Saturn; and the recently launched New Horizons mission to Pluto. Radioisotopes have also served as a versatile heat source for moderating equipment thermal environments on these and many other missions, including the Mars exploration rovers, Spirit and Opportunity. The key advantage of RPS is its ability to operate continuously, independent of orientation and distance relative to the Sun. Radioisotope systems are long-lived, rugged, compact, highly reliable, and relatively insensitive to radiation and other environmental effects. As such, they are ideally suited for missions involving long-lived, autonomous operations in the extreme conditions of space and other planetary bodies. This paper reviews the history of RPS for the U.S. space program. It also describes current development of a new Stirling cycle-based generator that will greatly expand the application of nuclear-powered missions in the future.

Schmidt, George↗
NASA NTRS2009

Radioisotope Power: A Key Technology for Deep Space Explorations

A Radioisotope Power System (RPS) generates power by converting the heat released from the nuclear decay of radioactive isotopes, such as Plutonium-238 (Pu-238), into electricity. First used in space by the U.S. in 1961, these devices have enabled some of the most challenging and exciting space missions in history, including the Pioneer and Voyager probes to the outer solar system; the Apollo lunar surface experiments; the Viking landers; the Ulysses polar orbital mission about the Sun; the Galileo mission to Jupiter; the Cassini mission orbiting Saturn; and the recently launched New Horizons mission to Pluto. Radioisotopes have also served as a versatile heat source for moderating equipment thermal environments on these and many other missions, including the Mars exploration rovers, Spirit and Opportunity. The key advantage of RPS is its ability to operate continuously, independent of orientation and distance relative to the Sun. Radioisotope systems are long-lived, rugged, compact, highly reliable, and relatively insensitive to radiation and other environmental effects. As such, they are ideally suited for missions involving long-lived, autonomous operations in the extreme conditions of space and other planetary bodies. This paper reviews the history of RPS for the U.S. space program. It also describes current development of a new Stirling cycle-based generator that will greatly expand the application of nuclear-powered missions in the future.

Schmidt, George R.↗
NASA NTRS1987

A new interpretation of plasma-line overshoot phenomena

The temporal evolution of Langmuir waves excited by high-power, high-frequency (HF) radio waves in the ionosphere is studied theoretically. This study is motivated by past observations made with the 450 MHz radar at Arecibo Observatory in Puerto Rico. Two kinds of nonlinear damping to the parametric decay instability are considered in the derivation of the rate equation for the spectral intensity of enhanced Langmuir waves. They are Langmuir wave cascading caused by nonlinear Landau damping and cross-field electron diffusion. The first damping process leads to the saturation of individual unstable Langmuir wave. The second process, which results from the incoherent scattering of electron orbits by the total excited Langmuir waves, yields anomalous damping that applies to each Langmuir wave. Consequently, Langmuir waves with smaller growth rates will be suppressed by those with larger growth rates. Such a mode competition process may cause the overshoot of the HF-enhanced plasma line observed with the Arecibo 430 MHz radar. Favorable agreement is obtained between theory and the Arecibo observations.

Kuo, S. P.↗
NASA NTRS1989

Continuous electron stimulated desorption using a ZrO2/Ag permeation membrane

During the development of an atomic oxygen beam generator for laboratory simulation of the atmospheric conditions in low earth orbit, a new technique for performing electron stimulated desorption (ESD) in a continuous manner has been developed. In this technique, oxygen permeates through an Ag membrane at elevated temperature thereby providing a continuous supply of oxygen atoms to the 1000-A ZrO2 coating at the vacuum interface. ESD then results in a large peak of neutral O2 molecules which ultimately decay into steady-state desorption. The ESD signal is linear with respect to primary beam flux (0.035 O2 molecules per electron at a primary beam energy of 1 keV) but nonlinear with respect to primary beam energy.

Outlaw, R. A.↗
NASA NTRS2013

An Electric Propulsion "Shepherd" for Active Debris Removal that Utilizes Ambient Gas as Propellant

There is a growing consensus among the space debris technical community that limiting the long ]term growth of debris in Low-Earth Orbit (LEO) requires that space users limit the accumulation of mass in orbit. This is partially accomplished by mitigation measures for current and future LEO systems, but there is now interest in removing mass that has already accumulated in LEO from more than 50 years of space activity (termed "Active Debris Removal", or ADR). Many ADR proposals face complex technical issues of how to grapple with uncooperative targets. Some researchers have suggested the use of conventional ion thrusters to gently "blow" on objects to gradually change their orbits, without ever having to come into physical contact with the target. The chief drawback with these methods is the cost per object removed. Typically, a space "tug" or an ion-drive "shepherd" can only remove a few objects per mission due to limited propellant. Unless a costeffective way that removes tens of objects per mission can be found, it is not clear that any of the ideas so far proposed will be economically viable. In this paper, a modified version of the ion-drive "shepherd" is proposed that uses ambient atmospheric gases in LEO as propellant for the ion drives. This method has the potential to greatly extend the operational lifetime of an ADR mission, as the only mission limit is the lifetime of the components of the satellite itself, not on its fuel supply. An ambient-gas ion-drive "shepherd" would the local atmospheric drag on an object by ionizing and accelerating the ambient gas the target would have encountered anyway, thereby hastening its decay. Also, the "shepherd" satellite itself has a great deal of flexibility to maneuver back to high altitude and rendezvous with its next target using the ion drive not limited by fuel supply. However, the amount of available ambient gas is closely tied to the altitude of the spacecraft. It may be possible to use a "hybrid" approach that supplements high-altitude ion-drive operations with stored gas, and transitions to ambient gas at lower altitudes. This paper will include realistic numbers on the estimated times needed to deorbit objects from different orbit regimes using drives that either partially or completely take advantage of ambient gas. It will conclude with recommendations on whether this is a viable candidate for future ADR efforts.

Matney, Mark J.↗