SEARCH · Engineering Papers

Results for “LIQUID WASTES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

All sources NASA NTRS DOE OSTI

NASA NTRS1991

Multimegawatt potassium Rankine power for nuclear electric power

A cermet fueled potassium rankine power system concept has been developed for various power ranges and operating lifetimes. This concept utilizes a single primary lithium loop to transport thermal energy from the reactor to the boiler. Multiple, independent potassium loops are employed to achieve the required reliability of 99 percent. The potassium loops are two phase systems which expand heated potassium vapor through multistage turboalternators to produce a 10-kV dc electrical output. Condensation occurs by-way-of a shear-flow condenser, producing a 100 percent liquid potassium stream which is pumped back to the boiler. Waste heat is rejected by an advanced carbon-carbon radiator at approximately 1000 K. Overall system efficiencies of 19.3 percent to 20.5 percent were calculated depending on mission life and power level.

Rovang, Richard D.↗

NASA NTRS2020

Development of a Thermal Management System for Electrified Aircraft

This paper describes the development and optimization of a conceptual thermal management system for electrified aircraft. Here, a vertical takeoff and landing (VTOL) vehicle is analyzed with the following electrically sourced heat loads considered: motors, generators, rectifiers, and inverters. The vehicle will employ liquid-cooling techniques in order to acquire, transport, and reject waste heat from the vehicle. The purpose of this paper is to threefold: 1) Present a potential modeling framework for system level thermal management system simulation, 2) Analyze typical system characteristics, and 3) Perform optimization on a system developed for a specific vehicle to minimize weight gain, power utilization, and drag. Additionally, the paper will study the design process, specifically investigating the differences between steady state and transient sizing, comparing simulation techniques with a lower fidelity option and quantifying expected error.

Chapman, Jeffryes W.↗

DOE OSTI2021

A Comparative Techno-Economic Analysis of Renewable Methanol Synthesis Pathways from Biomass and CO2: Preprint

Global demand for methanol as both a chemical precursor and a fuel additive is rising. At the same time, numerous sustainable methanol production pathways are under development which, if commercialized, could present significant environmental benefits over traditional methanol synthesis pathways. There is a need to harmonize the analyses of sustainable pathways using a consistent techno-economic approach to evaluate the potential for commercialization of various pathways. This analysis considers economic and environmental factors critical to market acceptance of three sustainable pathways versus a commercial baseline. We suggest that biomass gasification to methanol represents a near-term viable pathway with high technology readiness level and commercially competitive market price. However, long-term solutions should consider CO2 electrolysis pathways which offer further improvements in sustainability metrics to support global decarbonization efforts.

biomass↗

DOE OSTI2021

A Comparative Techno-Economic Analysis of Sustainable Methanol Synthesis Pathways from Biomass and CO2

The call to reduce global CO2 emissions is at the forefront of research and development in the transportation and petrochemical industries. A potential solution which intersects both sectors is the adoption and commercialization of more sustainable technologies for methanol production. Currently, methanol is gaining popularity as a possible fuel additive, and as a polymer precursor via established methanol-to-olefins routes which are increasing in capacity and utilization, putting methanol in the spotlight and global methanol production on the rise. At the same time, experimental and computational studies have surged, illuminating a wide array of novel process designs to introduce sustainable methanol into the market. However, with numerous competing pathways identified across a variety of fossil and non-fossil feedstocks, there is a need to harmonize the analyses of these pathways using a consistent techno-economic approach and compare them to current commercial pathways to better understand the benefits or limitations inherent to each technology. In this work we conduct a consistent comparative analysis of three sustainable methanol synthesis pathways versus a commercial baseline, with biomass, CO2, and natural gas as the carbon sources. The three sustainable pathways of interest are biomass gasification to syngas with subsequent catalytic conversion of syngas to methanol, indirect conversion of CO2 to syngas via electrolysis with subsequent catalytic conversion of syngas to methanol, and direct conversion of CO2 to methanol via electrolysis. To elucidate the challenges and opportunities in the path to commercialization of each sustainable pathway, we investigate five key process metrics: production cost, carbon efficiency, carbon intensity, energy efficiency, and technology readiness level (TRL).

biomass↗

DOE OSTI2021

Cesium Ion Exchange Testing Using Crystalline Silicotitanate with Hanford Tank Waste 241-AP-107

At the time of this testing, the Low-Activity Waste Pretreatment System (LAWPS) was to provide for the initial production of immobilized low-activity waste by feeding Hanford tank supernate from tank farms to the Hanford Tank Waste Treatment and Immobilization Plant (WTP) Low-Activity Waste (LAW) Facility for immobilization. Washington River Protection Solutions requested that Hanford tank waste collected from tank 241-AP-107 (hereafter called AP-107) be processed using conceived pretreatment steps (suspended solids removal by filtration, Cs removal by ion exchange) then vitrified. A small-scale test platform to demonstrate the solids filtration, Cs removal, and LAW vitrification was constructed and installed at Pacific Northwest National Laboratory. Bench-scale ion exchange testing with approximately 9 L of AP-107 supernate was conducted using crystalline silicotitanate (CST) ion exchange media. The IONSIV R9140-B CST was provided by Honeywell UOP, LLC in 2018 (Batch 2081000057). The ion exchange media was first tested with simulant and was previously described. This report describes the Cs ion exchange batch contact and column test results with the AP-107 tank waste. Batch contact testing helps to evaluate CST performance on tank waste supernate prior to processing it in the ion exchange columns. Batch contacts were performed with the waste at four Cs concentrations at a phase ratio of 200 (liquid volume to exchanger mass) with AP-107. The distribution coefficient (K d ) at the equilibrium condition of 8.57 µg Cs/mL (AP-107 feed condition) was determined to be 669 mL AP-107/g CST. With a CST bed density of 1.00 g/mL, this K d corresponded to a predicted 50% Cs breakthrough of 669 bed volumes (BVs). The Cs load capacity at the equilibrium feed condition was determined to be 7.5 mg Cs/g dry CST. The column testing was prototypic to the intended LAWPS operations in a lead-lag column format, although on a small-scale basis with 10-mL CST beds. The feed was processed downflow through the lead column and then through the lag column at ~2.2 BV/h. Loading continued until the lag column reached the WTP waste acceptance criteria (WAC) for receiving supernatant waste for vitrification (a function of the Na and 137 Cs concentrations). For AP-107, the WAC is 0.114% of the influent 137 Cs concentration; this required a Cs decontamination factor of 876. The Cs effluent from the lag column reached the WAC after processing ~410 BVs. To keep the subsequent product effluent below the WAC, a replacement lag column was prepared, the lead column was removed from service (after processing a total of 471 BVs), the lag column was put into the lead column position, and the replacement lag column was installed. Feed processing continued and after another ~290 BVs the Cs effluent from the lag column again exceeded the WAC. In both cases, the lead columns only reached 25% Cs breakthrough before removal. Although 50% Cs breakthrough was not reached, this value was estimated and averaged based on extrapolation of the loading curves (640 BVs) and agreed within 4% of the predicted 50% Cs breakthrough from batch contact test results (669 BVs). Table ES.1 summarizes the observed column performance and relevant Cs loading characteristics.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2022

Potential for Evaporation and In Situ Reaction of Organic Compounds in Hanford Supplemental LAW

The presence of regulated organic species in Hanford nuclear tank waste is assessed in this report, along with fate of the organics and possible evaporative treatment. A narrowed list of regulated organic species of concern is developed based upon published analyses, chemical properties like aqueous solubility, and chemical reactivity under alkaline conditions. Published analyses include tank headspace and liquid samples, review of chemical reagents formerly used at Hanford, and the Tank Waste Information Network System (TWINS). This work supports possible stabilization of Hanford Supplemental Low Activity Waste (SLAW) by grouting.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2022

Potential for Evaporation and In Situ Reaction of Organic Compounds in Hanford Supplemental LAW

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2021

A comparative techno-economic analysis of renewable methanol synthesis from biomass and CO 2 : Opportunities and barriers to commercialization

Global demand for methanol as both a chemical precursor and a fuel additive is rising. At the same time, numerous renewable methanol production pathways are under development, which, if commercialized, could provide significant environmental benefits over traditional methanol synthesis pathways. However, it is difficult to compare technologies at different maturity levels, with differing feedstocks, and with significant differences in overall process design. Thus, there is a need to harmonize the analyses of renewable pathways using a consistent techno-economic approach to evaluate the potential for commercialization of various pathways. This analysis uses a novel cross-comparison method to assess near-term and long-term viability of both low- and high-maturity level technologies. Furthermore, the techno-economic assessment considers cost factors critical to market acceptance combined with carbon- and energy-efficiency assessments of three renewable pathways compared with a commercial baseline. We find that biomass gasification to methanol represents a near-term viable pathway with a high technology readiness level and commercially competitive market price. If cost-reducing technological improvements can be realized and scaled up in the CO 2 electrolysis pathways, the potential for higher carbon efficiencies may help drive market adoption of these more modular, direct conversion pathways in future markets as they present an opportunity to better support global decarbonization efforts through efficient waste carbon utilization.

09 BIOMASS FUELS↗

NASA NTRS2005

Feasibility Study of a Nuclear-Stirling Plant for the Jupiter Icy Moons Orbiter

NASA is undertaking the design of a new spacecraft to explore the planet Jupiter and its three moons Calisto, Ganymede and Europa. This proposed mission, known as Jupiter Icy Moons Orbiter (JIMO) would use a nuclear reactor and an associated electrical generation system (Reactor Power Plant-RPP) to provide power to the spacecraft. The JIMO spacecraft is envisioned to use this power for science and communications as well as Electric Propulsion (EP). Among other potential power-generating concepts, previous studies have considered Thermoelectric and Brayton Power conversion systems, coupled to a liquid metal reactor for the JIMO mission. This paper will explore trades in system mass and radiator area for a nuclear reactor power conversion system, however this study will focus on Stirling power conversion. The Stirling convertor modeled in this study is based upon the Component Test Power Convertor design that was designed and operated successfully under the Civil Space Technology Initiative for use with the SP-100 nuclear reactor i the 1980's and early 1990's. The study design is such that two of the four convertors would operate at any time to generate the 100 kWe while the others are held in reserve. For this study the Stirling convertors hot-side temperature is 1050 K, would operate at a temperature ratio of 2.4 for a minimum mass system and would have a system efficiency of 29%. The Stirling convertor would generate high voltage (400 volt), 100 Hz single phase AC that is supplied to the Power Management and Distribution system. The waste hear is removed from the Stirling convertors by a flowing liquid sodium-potassium eutectic and then rejected by a shared radiator. The radiator consists of two coplanar wings, which would be deployed after the reactor is in space. System trades were performed to vary cycle state point temperatures and convertor design as well as power output. Other redundancy combinations were considered to understand the affects of convertor size and number of spares to the system mass.

Schmitz, Paul C.↗

NASA NTRS2013

Flash Cracking Reactor for Waste Plastic Processing

Conversion of waste plastic to energy is a growing problem that is especially acute in space exploration applications. Moreover, utilization of heavy hydrocarbon resources (wastes, waxes, etc.) as fuels and chemicals will be a growing need in the future. Existing technologies require a trade-off between product selectivity and feedstock conversion. The objective of this work was to maintain high plastic-to-fuel conversion without sacrificing the liquid yield. The developed technology accomplishes this goal with a combined understanding of thermodynamics, reaction rates, and mass transport to achieve high feed conversion without sacrificing product selectivity. The innovation requires a reaction vessel, hydrocarbon feed, gas feed, and pressure and temperature control equipment. Depending on the feedstock and desired product distribution, catalyst can be added. The reactor is heated to the desired tempera ture, pressurized to the desired pressure, and subject to a sweep flow at the optimized superficial velocity. Software developed under this project can be used to determine optimal values for these parameters. Product is vaporized, transferred to a receiver, and cooled to a liquid - a form suitable for long-term storage as a fuel or chemical. An important NASA application is the use of solar energy to convert waste plastic into a form that can be utilized during periods of low solar energy flux. Unlike previous work in this field, this innovation uses thermodynamic, mass transport, and reaction parameters to tune product distribution of pyrolysis cracking. Previous work in this field has used some of these variables, but never all in conjunction for process optimization. This method is useful for municipal waste incinerator operators and gas-to-liquids companies.

Timko, Michael T.↗

DOE OSTI2021

Ionic liquid-water mixtures enhance pretreatment and anaerobic digestion of agave bagasse

Agave bagasse (AB), a byproduct of tequila production, is a waste generated in large quantities and an emerging alternative for biofuels production. Nevertheless, the use of lignocellulosic biomass for this purpose requires a pretreatment that maximizes its degradation and utilization. Although there are several pretreatment types, using ionic liquids (IL) has become attractive due to its ability to dissolve the lignocellulosic biomass under mild conditions of time and temperature. As a drawback are the high cost of IL's and their high viscosity; thus mixing them with water is a way to overcome these hindrances. This work aimed to evaluate the effect of pretreatment with three diluted ILs on the A. tequilana bagasse structure and sugars production, as well as the potential of the enzymatic hydrolysate to produce methane in batch mode. The evaluated ILs were: 1-ethyl-3-methylimidazolium acetate [Emim][OAc], choline lysinate [Ch][Lys] and ethanolamine acetate [EOA][OAc]. The results showed that the IL with the best performance was [Ch][Lys], which not only offered the highest yields of sugar production (0.57 ± 0.03 g total sugars / g bagasse) but also, it is possible to use it at 30 % in a mix with water obtaining similar yields as with pure IL. Enzymatic hydrolysis of IL pretreated AB achieved 50.7 kg sugars and 49.3 kg of sugars for 90 %-[Ch][Lys] and 30 %-[Ch][Lys], respectively per 100 kg of untreated biomass. The enzymatic hydrolysate from the 30 %-[Ch][Lys] pretreated AB was able to achieve 0.28 L CH4/g CODfed, demonstrating that both sugar and methane yields are maintained when pure or 30 %-[Ch][Lys] are used for pretreatment, representing a step forward towards process feasibility.

59 BASIC BIOLOGICAL SCIENCES↗

NASA NTRS2005

Utilizing Radioisotope Power System Waste Heat for Spacecraft Thermal Management

An advantage of using a Radioisotope Power System (RPS) for deep space or planetary surface missions is the readily available waste heat, which can be used for a number of beneficial purposes including: maintaining electronic components within a controlled temperature range, warming propulsion tanks and mobility actuators, and maintaining liquid propellants above their freezing temperature. Previous missions using Radioisotope Thermoelectric Generators (RTGs) dissipated large quantities of waste heat due to the low efficiency of the thermoelectric conversion technology. The next generation RPSs, such as the 110-Watt Stirling Radioisotope Generator (SRG110) will have higher conversion efficiencies, thereby rejecting less waste heat at a lower temperature and may require alternate approaches to transferring waste heat to the spacecraft. RTGs, with efficiencies of ~6 to 7 percent, reject their waste heat at the relatively high heat rejection temperature of 200 C. This is an advantage when rejecting heat to space; however, transferring heat to the internal spacecraft components requires a large and heavy radiator heat exchanger. At the same time, sensitive spacecraft instruments must be shielded from the thermal radiation of the RTG. The SRG110, with an efficiency around 22 percent and 50 C nominal housing surface temperature, can readily transfer the available waste heat directly via heat pipes, thermal straps, or fluid loops. The lower temperatures associated with the SRG110 avoid the chances of overheating other scientific components, eliminating the need for thermal shields. This provides the spacecraft designers more flexibility when locating the generator for a specific mission. A common misconception with high-efficiency systems is that there is not enough waste heat for spacecraft thermal management. This paper will dispel this misconception and investigate the use of a high-efficiency SRG110 for spacecraft thermal management and outline potential methods of waste heat utilization in several conceptual missions (Lunar Rover, Mars Rover, and Titan Lander). The advantages associated with the SRG110 as they relate to ease of assembly, less complex interfaces, and overall mass savings for a spacecraft will be highlighted.

Pantano, David R.↗

DOE OSTI2020

LDRD Macromolcule Radiolysis Poster

Moving toward a circular carbon economy depends on enabling reuse of carbon-based macromolecules and increased recycling of waste products into higher value products. Macromolecules are challenging to valorize into products easily converted into liquid fuel or chemical feedstocks, due to their large and sometimes heterogeneous network of polymeric bonds. The novel aspect of this project is to show a proof of principle that radiolysis of macromolecules using “waste” radiation from energy production in the presence of radical capping donors presents an attractive opportunity to break down complex macromolecules into smaller molecules while controlling re-polymerization. This approach offers a new, cost-efficient way to utilize “waste” radiation and heat byproducts of nuclear energy production to convert a simple mixture of complex molecules into a complex mixture of small molecules, to be utilized as an energy source by the fuel industry, or to create value-added feedstocks for new polymers or commodity chemicals. Ionizing radiation can be harnessed to convert energy to molecules, adding value to low-value macromolecules as they are broken down into smaller, more easily separated feedstocks or fuels to be converted to a value-added product. This project will test 2 hypotheses. Hypothesis 1: Macromolecular materials that comprise biomass and coal or other macromolecules can be infused with radical capping donors (RCDs), and gamma irradiation of the resulting mixtures will produce ensembles of lower-molecular weight chemicals that can be more easily separated. If this expectation is realized, the conversion chemistry can be optimized by adjusting the feedstock composition, irradiation time, and choice of RCD.

02 - PETROLEUM↗

DOE OSTI2022

Effect of Macro- and Microstructures on Catalytic Hydrogenolysis of Polyolefins

Here, polyethylenes of varying molecular weight and branch density, as well as polypropylenes of varying molecular weight and tacticity, were catalytically converted to lower-molecular-weight liquid products to showcase how these various properties in a mixed waste plastic stream could affect the final product. A Pt nanoparticle on a strontium titanate nanocuboid (Pt/STO) catalyst was used under solvent-free conditions in the presence of 170 psi of H 2 at 300 °C for hydrogenolysis. The initial molecular weight of polyethylene was found to have a moderate effect on the yield to the final product (ranging from 55 wt% for M n ~ 7600 Da to 67 wt% for M n ~ 50,950 Da). The microstructure, defined as the length and density of branches in a polymer, of higher-molecular-weight polymers was the dominant factor in determining the yield (ranging from 67 wt% for M n ~ 50,950 Da for linear low-density polyethylene (LLDPE) with C 2 branches to 97 wt% for M n ~ 38,850 Da for LLDPE with C 6 branches). The same products (M n = C 29 –C 46 , Ð = 1.1–1.6) and distribution of undesired light gases (C 1 –C 4 ≈ 90 mol%, C 5 –C 8 ≈ 10 mol%) are obtained from conversions of PE of varying molecular weight. The tacticity of polypropylene at a given molecular weight had a significant effect on the molecular weight of the final product, while not strongly affecting conversion. Hydrogenolysis of isotactic polypropylene (iPP) produced ≈C 18 with a wider polydispersity (Ð ~ 1.4) compared to the narrow ≈C 64 (Ð ~ 1.0) and ≈C 54 (Ð ~ 1.0) products from atactic (aPP) and syndiotactic (sPP) polypropylene, respectively. The stereochemistry of the methyl groups dictates the shape and structure of the polymer in the melt, which in turn affects how the hydrocarbon chain interacts with the catalyst surface, thereby impacting the number of C–C scissions. These results show how various characteristics such as the molecular weight and structure of a waste plastic stream could affect the final product.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Conversion of plastic waste into high-value lubricants: techno-economic analysis and life cycle assessment

Given the low recycling rate of plastic waste in the United States due to low economic incentives, it is of great interest to develop a technology to upgrade plastic waste with favorable economics. Plastic upcycling to valuable chemicals could ensure a circular economy for plastics and reduce the environmental burden caused by their end use cycle and disposal. A conceptual facility to convert 250 metric ton (MT) per day of plastic waste was modeled; the main product was a high-quality liquid (HQL) with a similar performance to polyalphaolefin (PAO) lubricants. The modeled process had a lubricant yield of up to 90% based on the experimental results at the laboratory scale. Techno-economic analysis (TEA) and life cycle assessment (LCA) were also performed to evaluate the process economics and its environmental impact. By using a mixture of colored and natural high-density polyethylene (HDPE), the production cost was in the range of 0.6–1.98 dollars per kg of lubricant, depending on the operating conditions. The life cycle emissions were in the range of 0.48–1.2 kg CO 2e kg Lub -1 showing, for the best case scenario, a 52% reduction relative to the emissions for petroleum lubricants, and a 74% reduction relative to the emissions for PAO lubricants. Finally, the impacts of the lubricant yield, the catalyst amount, and reaction time were evaluated, and their effect on the final production cost was discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1995

Environmentally Sound Processing Technology: JANNAF Safety and Environmental Protection Subcommittee and Propellant Development and Characterization Subcommittee Joint Workshop

Topics covered include: Risk assessment of hazardous materials, Automated systems for pollution prevention and hazardous materials elimination, Study design for the toxicity evaluation of ammonium perchlorate, Plasma sprayed bondable stainless surface coatings, Development of CFC-free cleaning processes, New fluorinated solvent alternatives to ozone depleting solvents, Cleaning with highly fluorinated liquids, Biotreatment of propyleneglycol nitrate by anoxic denitrification, Treatment of hazardous waste with white rot fungus, Hydrothermal oxidation as an environmentally benign treatment technology, Treatment of solid propellant manufacturing wastes by base hydrolysis, Design considerations for cleaning using supercritical fluid technology, and Centrifugal shear carbon dioxide cleaning.

Pickett, Lorri A.↗

DOE OSTI2022

Characterization of Contaminants and Mobility in WMA A-AX Boreholes D0006 and D0008

This study was initiated to determine if subsurface contaminants in the A-AX vadose zone at the Hanford site (boreholes D0006 and D0008) caused corrosion of nearby stainless steel well casings (299-E-24-19, 299-E25-46, and 299-E25-236) and, based on the type and distribution of contaminants, determine if contaminants are from one or more sources including a) the A-104 and/or A-105 tanks, b) the 242A evaporator, and c) the 200-E-286 ditch. A tiered approach was used for characterizing contaminants in vadose zone sediments starting with mobile and total contaminant concentrations (Tier 1), characterizing contaminant speciation (Tier 2), and measuring contaminant leaching (Tier 3). Total and mobile contaminant measurements at seven depths showed elevated sulfate and nitrate in all samples (130 to 280 ft depth), elevated chloride in five depths, and no elevated radionuclides except I-129 in D0006 at 206 to 208 ft depth. If these contaminants were initially acidic, stainless-steel corrosion would occur. However, because sediments likely have a high acid neutralization capacity, an acidic spill would have been neutralized within tens of feet, so casing corrosion would likely occur in shallow sediments. GEL labs data also shows low (but above natural) chromate from shallow to 170 ft depth, then higher chromate to 280 ft, suggesting a surface Cr spill or casing corrosion. GEL labs data also showed evidence of more than one plume, with deep nitrate, sulfate, and chloride migration, but only shallow tritium migration. Tritium should migrate nearly unretarded in the subsurface like nitrate and chloride. Elevated aqueous cations and anions in the D0006 206 to 208' depth pore water (SO 4 2- , NO 3 - , Na + , K + , Ca 2+ , Mg 2+ , Si) could be the result of acid disposal and calcite dissolution at shallow depth, with deeper migration of SO 4 2- , NO 3 - from acids and Ca 2+ and Mg 2+ from calcite. Elevated Si (160 mg/L) indicates dissolution of clays or other silicates, which can also occur in acids. Acid extractable metals did show elevated Cr (but not Fe, Ni, Mo, and Mn) above natural levels, which may indicate stainless-steel well corrosion or transport of metals from a shallow spill. The elevated I-129 in D0006 at 206 to 208' depth was low with 0.34 μg/g in pore water and 1.5 μg/g total extractable I-129 in the sediment, which indicates significant fraction of I-129 was bound in one or more precipitates. Although total I-129 was below detection limits in most extractions due to high molybdate interference, I-127 analysis provided some insight into potential precipitate phases. Total I-127 was mainly extracted by acetate or acetic acid (67%), which may be iodine in calcite. Inorganic carbon measurement identified 1.65% calcite, and total organic carbon (TOC) was below detection limits, so iodine was not associated with organic matter. Nearly all the I-127 was present as iodide. In 1-D leach experiments, I-127 as iodide leached from the sediment within 2 pore volumes. Due to high and dynamic molybdate leaching from the sediment and interference with I-129 analysis, there were few quantifiable I-129 measurements. The calculated molybdate release rates from the sediment suggested Mo was being released from the same precipitate phase, such as molybdate incorporated into calcite. Overall, because there was little radioactive contamination measured in D0006 and D0008 boreholes, potential releases from A-104 and A-105 did not reach this location south of the A tank farm. Elevated cations and anions found in D0006 and D0008 at depth as the result of acidic disposal could cause shallow stainless steel casing corrosion. The nearby 242A evaporator generally contained alkaline waste and tritium, but the nearby 200-E-286 ditch generally contained high Cl - liquid effluent, so these are unlikely to be acidic sources.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2023

Irradiation Effect on Noble Metal Particles in Water Using in situ Liquid Cell STEM Observation

During geologic disposal of spent nuclear fuel (SNF) in an engineered nuclear waste repository, once all other barriers have degraded, oxidizing may occur at the solid-water interface owing to a self-generated radiolytic field. The repository design includes large quantities of iron (Fe), that is anticipated to corrode under an anoxic environment, and generate hydrogen (H 2 ) gas. This H 2 gas is thought to be able to suppress the dissolution of SNF through a catalytic reaction with noble metal particles (NMP) that are pre-existing in the SNF. This interaction leads to the decomposition of the major oxidant, hydrogen peroxide (H 2 O 2 ). In conclusion, these processes are described in the Fuel Matrix Degradation (FMD) model that is being used to predict SNF degradation rates. The NMP, therefore, plays an important role within the FMD model.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗