Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LENGTH”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Macrosegregation During Dendritic Arrayed Growth of Hypoeutectic Pb-Sn Alloys: Influence of Primary Arm Spacing and Mushy Zone Length

Thermosolutal convection in the dendritic mushy zone occurs during directional solidification of hypoeutectic lead tin alloys in a positive thermal gradient, with the melt on the top and the solid below. This results in macrosegregation along the length of the solidified samples. The extent of macrosegregation increases with increasing primary dendrite spacings for constant mushy zone length. For constant primary spacings, the macrosegregation increases with decreasing mushy zone length. Presence of convection reduces the primary dendrite spacings. However, convection in the interdendritic melt has significantly more influence on the spacings as compared with that in the overlying melt, which is caused by the solutal buildup at the dendrite tips.

Tewari, S. N.↗
NASA NTRS1997

Noise Reduction with Lobed Mixers: Nozzle-Length and Free-Jet Speed Effects

Acoustic test results are presented for 1/4th-scaled nozzles with internal lobed mixers used for reduction of subsonic jet noise of turbofan engines with bypass ratio above 5 and jet speeds up to 830 ft/s. One coaxial and three forced lobe mixers were tested with variations in lobe penetration, cut-outs in lobe-sidewall, lobe number and nozzle-length. Measured exit flow profiles and thrusts are used to assist the inferences from acoustic data. It is observed that lobed mixers reduce the low-frequency noise due to more uniformly mixed exit flow; but they may also increase the high-frequency noise at peak perceived noise (PNL) angle and angles upstream of it due to enhanced mixing inside the nozzle. Cut-outs and low lobe penetration reduce the annoying portion of the spectrum but lead to less uniform exit flow. Due to the dominance of internal duct noise in unscalloped, high-penetration mixers their noise is not reduced as much with increase in free-jet speed as that of coaxial or cut-out lobed mixers. The latter two mixers also show no change in PNL over the wide range of nozzle-lengths tested because most of their noise sources are outside the nozzle; whereas, the former show an increase in noise with decrease in nozzle-length.

Mengle, Vinod G.↗
NASA NTRS1961

Applicability of Mixing Length Theory to a Turbulent Vortex System

The ability of mixing length theory to correlate vortex data is evaluated. Expressions are derived for eddy diffusivity by applying the techniques of von Karman and Prandtl which have been established for pipe flow. Total and static pressures were measured from the outer radius to the exhaust-nozzle radius of a vortex generator for a range of mass flows. These data are combined with Navier-Stokes solutions for this region of a compressible vortex to determine turbulent Reynolds numbers. The Reynolds number is related to Prandtl and Karman functions for various assumed boundary conditions, and the experimental data are used to determine the usefulness of these expressions. The following conclusions were reached: (1) Mixing length functions developed by applying von Karman's similarity hypothesis to vortex motion correlate the data better than do Prandtl functions obtained with the assumption that mixing length is proportional to radius. (2) Some of the expressions developed do not adequately represent the experimental data. (3) The data are correlated with acceptable scatter by evaluating the fluid radial inertia at the outer boundary and the shear stress at the inner boundary. The universal constant K was found to be 0.04 to 0.08, rather than the value of 0.4 which is accepted for rectilinear flow. (4) The data are best correlated by a modified Karman expression which includes an effect of radial inertia, as well as shear stress, on eddy diffusivity.

Ragsdale, Robert G.↗
NASA NTRS1999

A Combined Length-of-Day Series Spanning 1832-1997

The Earth's rotation is not constant but exhibits minute changes on all observable time scales ranging from subdaily to secular. This rich spectrum of observed Earth rotation changes reflects the rich variety of astronomical and geophysical phenomena that are causing the Earth's rotation to change, including, but not limited to, ocean and solid body tides, atmospheric wind and pressure changes, oceanic current and sea level height changes, post-glacial rebound, and torques acting at the core-mantle boundary. In particular, the decadal-scale variations of the Earth's rotation are thought to be largely caused by interactions between the Earth's outer core and mantle. Comparing the inferred Earth rotation variations caused by the various core-mantle interactions to observed variations requires Earth rotation observations spanning decades, if not centuries. During the past century many different techniques have been used to observe the Earth's rotation. By combining the individual Earth rotation series determined by each of these techniques, a series of the Earth's rotation can be obtained that is based upon independent measurements spanning the greatest possible time interval. In this study, independent observations of the Earth's rotation are combined to generate a length-of-day series spanning 1832-1997. The observations combined include lunar occultation measurements spanning 1832-1955, optical astrometric measurements spanning 1956-1982, lunar laser ranging measurements spanning 1970-1997, and very long baseline interferometric measurements spanning 1978-1998. These series are combined using a Kalman filter developed at JPL for just this purpose. The resulting combined length-of-day series will be presented and compared with other available length-of-day series of similar duration.

Gross, Richard S.↗
NASA NTRS1998

MRI Evaluation of Spinal Length and Vertebral Body Angle During Loading with a Spinal Compression Harness

Weight bearing by the spinal column during upright posture often plays a role in the common problem of low back pain. Therefore, we developed a non-ferromagnetic spinal compression harness to enable MRI investigations of the spinal column during axial loading. Human subjects were fitted with a Nest and a footplate which were connected by adjustable straps to an analog load cell. MRI scans of human subjects (5 males and 1 female with age range of 27-53 yrs) during loaded and unloaded conditions were accomplished with a 1.5 Tesla GE Signa scanner. Studies of two subjects undergoing sequentially increasing spinal loads revealed significant decreases (r(sup 2) = 0.852) in spinal length between T4 and L5 culminating in a 1.5 to 2% length decrease during loading with 75% body weight. Sagittal vertebral body angles of four subjects placed under a constant 50% body weight load for one hour demonstrated increased lordotic and kyphotic curvatures. In the lumbar spine, the L2 vertebral body experienced the greatest angular change (-3 deg. to -5 deg.) in most subjects while in the thoracic spine, T4 angles increased from the unloaded state by +2 deg. to +9 deg. Overall, our studies demonstrate: 1) a progressive, although surprisingly small, decrease in spinal length with increasing load and 2) relatively large changes in spinal column angulation with 50% body weight.

Campbell, James A.↗
NASA NTRS2002

Fabrication of Extremely Short Length Fiber Bragg Gratings for Sensor Applications

A new technique and a physical model for writing extremely short length Bragg gratings in optical fibers have been developed. The model describes the effects of diffraction on the spatial spectra and therefore, the wavelength spectra of the Bragg gratings. Using an interferometric technique and a variable aperture, short gratings of various lengths and center wavelengths were written in optical fibers. By selecting the related parameters, the Bragg gratings with typical length of several hundred microns and bandwidth of several nanometers can be obtained. These short gratings can be apodized with selected diffraction patterns and hence their broadband spectra have a well-defined bell shape. They are suitable for use as miniaturized distributed strain sensors, which have broad applications to aerospace research and industry as well.

Wu, Meng-Chou↗
NASA NTRS2000

Co-conservation of rRNA tetraloop sequences and helix length suggests involvement of the tetraloops in higher-order interactions

Terminal loops containing four nucleotides (tetraloops) are common in structural RNAs, and they frequently conform to one of three sequence motifs, GNRA, UNCG, or CUUG. Here we compare available sequences and secondary structures for rRNAs from bacteria, and we show that helices capped by phylogenetically conserved GNRA loops display a strong tendency to be of conserved length. The simplest interpretation of this correlation is that the conserved GNRA loops are involved in higher-order interactions, intramolecular or intermolecular, resulting in a selective pressure for maintaining the lengths of these helices. A small number of conserved UNCG loops were also found to be associated with conserved length helices, consistent with the possibility that this type of tetraloop also takes part in higher-order interactions.

Non-NASA Center↗
NASA NTRS2004

Measurement of N-Type 6H SiC Minority-Carrier Diffusion Lengths by Electron Bombardment of Schottky Barriers

Minority-Carrier diffusion lengths of n-type 6H-SiC were measured using the electron-beam induced current (EBIC) technique. Experimental values of primary beam current, EBIC, and beam voltage were obtained for a variety of SIC samples. This data was used to calculate experimental diode efficiency vs. beam voltage curves. These curves were fit to theoretically calculated efficiency curves, and the diffusion length and metal layer thickness were extracted. The hole diffusion length in n-6H SiC ranged from 0.93 +/- 0.15 microns.

Hubbard, S. M.↗
NASA NTRS1997

Local homogeneity of cell cycle length in developing mouse cortex

We have measured the amount of variation in the length of the cell cycle for cells in the pseudostratified ventricular epithelium (PVE) of the developing cortex of mice on embryonic day 14. Our measurements were made in three cortical regions (i.e., the neocortex, archicortex, and periarchicortex) using three different methods: the cumulative labeling method (CLM), the percent labeled mitoses (PLM) method, and a comparison of the time needed for the PLM to ascend from 0 to 100% with the time needed for the PLM to descend from 100 to 0%. These 3 different techniques provide different perspectives on the cytokinetic parameters. Theoretically, CLM gives an estimate for a maximum value of the total length of the cell cycle (TC), whereas PLM gives an estimate of a minimum value of TC. The difference between these two estimates indicates that the range for TC is +/-1% of the mean TC for periarchicortex, +/-7% for neocortex, and +/-8% for archicortex. This was confirmed by a lengthening of the PLM descent time in comparison with its ascent time. The sharpness of the transitions and the flatness of the plateau of the PLM curves indicate that 99% of the proliferating cells are within this narrow estimated range for TC; hence, only approximately 1% deviate outside of a relatively restricted range from the average TC of the population. In the context of the possible existence within the cortical PVE of two populations with markedly dissimilar cell cycle kinetics from the mean, one such population must comprise approximately 99% of the total population, and the other, if it exists, is only approximately 1% of the total. This seems to be true for all three cortical regions. The narrow range of TC indicates a homogeneity in the cell cycle length for proliferating cells in three different cortical regions, despite the fact that progenitor cells of different lineages may be present. It further predicts the existence of almost synchronous interkinetic nuclear movements of the proliferating cells in the ventricular zone during early development of the cerebral cortex.

Non-NASA Center↗
NASA NTRS2005

Construction of Covariance Functions with Variable Length Fields

This article focuses on construction, directly in physical space, of three-dimensional covariance functions parametrized by a tunable length field, and on an application of this theory to reproduce the Quasi-Biennial Oscillation (QBO) in the Goddard Earth Observing System, Version 4 (GEOS-4) data assimilation system. These Covariance models are referred to as multi-level or nonseparable, to associate them with the application where a multi-level covariance with a large troposphere to stratosphere length field gradient is used to reproduce the QBO from sparse radiosonde observations in the tropical lower stratosphere. The multi-level covariance functions extend well-known single level covariance functions depending only on a length scale. Generalizations of the first- and third-order autoregressive covariances in three dimensions are given, providing multi-level covariances with zero and three derivatives at zero separation, respectively. Multi-level piecewise rational covariances with two continuous derivatives at zero separation are also provided. Multi-level powerlaw covariances are constructed with continuous derivatives of all orders. Additional multi-level covariance functions are constructed using the Schur product of single and multi-level covariance functions. A multi-level powerlaw covariance used to reproduce the QBO in GEOS-4 is described along with details of the assimilation experiments. The new covariance model is shown to represent the vertical wind shear associated with the QBO much more effectively than in the baseline GEOS-4 system.

Gaspari, Gregory↗
NASA NTRS2010

Measuring Crack Length in Coarse Grain Ceramics

Due to a coarse grain structure, crack lengths in precracked spinel specimens could not be measured optically, so the crack lengths and fracture toughness were estimated by strain gage measurements. An expression was developed via finite element analysis to correlate the measured strain with crack length in four-point flexure. The fracture toughness estimated by the strain gaged samples and another standardized method were in agreement.

Salem, Jonathan A.↗
NASA NTRS2010

Measurement of the Length of an Optical Trap

NASA Glenn has been involved in developing optical trapping and optical micromanipulation techniques in order to develop a tool that can be used to probe, characterize, and assemble nano and microscale materials to create microscale sensors for harsh flight environments. In order to be able to assemble a sensor or probe candidate sensor material, it is useful to know how far an optical trap can reach; that is, the distance beyond/below the stable trapping point through which an object will be drawn into the optical trap. Typically, to measure the distance over which an optical trap would influence matter in a horizontal (perpendicular to beam propagation) direction, it was common to hold an object in one optical trap, place a second optical trap a known distance away, turn off the first optical trap, and note if the object was moved into the second trap when it was turned on. The disadvantage of this technique is that it only gives information of trap influence distance in horizontal (x y) directions. No information about the distance of the influence of the trap is gained in the direction of propagation of the beam (the z direction). A method was developed to use a time-of-flight technique to determine the length along the propagation direction of an optical trap beam over which an object may be drawn into the optical trap. Test objects (polystyrene microspheres) were held in an optical trap in a water-filled sample chamber and raised to a pre-determined position near the top of the sample chamber. Next, the test objects were released by blocking the optical trap beam. The test objects were allowed to fall through the water for predetermined periods of time, at the end of which the trapping beam was unblocked. It was noted whether or not the test object returned to the optical trap or continued to fall. This determination of the length of an optical trap's influence by this manner assumes that the test object falls through the water in the sample chamber at terminal velocity for the duration of its fall, so that the distance of trap influence can be computed simply by: d = VTt, where d is the trap length (or distance of trap reach), VT is the terminal velocity of the test object, and t is the time interval over which the object is allowed to fall.

Wrbanek, Susan Y.↗
NASA NTRS2010

Path Length Fluctuations Derived from Site Testing Interferometer Data

To evaluate possible sites for NASA's proposed Ka-band antenna array, the NASA Glenn Research Center has constructed atmospheric phase monitors (APM) which directly measure the tropospheric phase stability. These instruments observe an unmodulated 20.2 GHz beacon signal broadcast from a geostationary satellite (Anik F2) and measure the phase difference between the signals received by the two antennas. Two APM's have been deployed, one at the NASA Deep Space Network (DSN) Tracking Complex in Goldstone, California, and the other at the NASA White Sands Complex, in Las Cruces, New Mexico. Two station-years of atmospheric phase fluctuation data have been collected at Goldstone since operations commenced in May 2007 and 0.5 station-years of data have been collected at White Sands since operations began February 2009. With identical instruments operating simultaneously, we can directly compare the phase stability at the two sites. Phase stability is analyzed statistically in terms of the root-mean-square (rms) of the tropospheric path length fluctuations over 10 min blocks. Correlation between surface wind speed and relative humidity with interferometer phase are discussed. For 2 years, the path length fluctuations at the DSN site in Goldstone, California, have been better than 757 micrometer (with reference to a 300 m baseline and to Zenith) for 90 percent of the time. For the 6 months of data collected at White Sands, New Mexico, the path length fluctuations have been better than 830 micrometers (with reference to a 300 m baseline and to Zenith) for 90 percent of the time. This type of data analysis, as well as many other site quality characteristics (e.g., rain attenuation, infrastructure, etc.), will be used to determine the suitability of both sites for NASA s future communication services at Ka-band using an array of antennas.

Acosta, Roberto J.↗
NASA NTRS2011

An Assessment of the Length and Variability of Mercury's Magnetotail

We employ Mariner 10 measurements of the interplanetary magnetic field in the vicinity of Mercury to estimate the rate of magnetic reconnection between the interplanetary magnetic field and the Hermean magnetosphere. We derive a time-series of the open magnetic flux in Mercury's magnetosphere. from which we can deduce the length of the magnetotail The length of the magnetotail is shown to be highly variable. with open field lines stretching between 15R(sub H) and 8S0R(sub H) downstream of the planet (median 150R(sub H)). Scaling laws allow the tail length at perihelion to be deduced from the aphelion Mariner 10 observations.

Milan, S. E.↗
NASA NTRSDate not supplied

In Vitro Selections with RNAs of Variable Length Converge on a Robust Catalytic Core

In vitro selection is a powerful tool that can be used to understand basic principles of molecular evolution. We used in vitro selection to understand how changes in length and the accumulation of point mutations enable the evolution of functional RNAs. Using RNA populations of various lengths, we performed a series of in vitro experiments to select for ribozymes with RNA ligase activity. We identified a core ribozyme structure that was robust to changes in RNA length, high levels of mutagenesis, and increased selection pressure. Elaboration on this core structure resulted in improved activity which we show is consistent with a larger trend among functional RNAs in which increasing motif size can lead to an exponential improvement in fitness. We conclude that elaboration on conserved core structures is a preferred mechanism in RNA evolution. This conclusion, drawn from selections of RNAs from random sequences, is consistent with proposed evolutionary histories of specific biological RNAs. More generally, our results indicate that modern RNA structures can be used to infer ancestral structures. Our observations also suggest a mechanism by which structural outcomes of early RNA evolution would be largely reproducible even though RNA fitness landscapes consist of disconnected clusters of functional sequences.

In vitro evolution↗
NASA NTRSDate not supplied

DC Modeling of 4H-SiC nJFET Gate Length Reduction at 500°C

The development of robust, high-performance integrated circuits (ICs) will enable numerous potential NASA missions of current interest, including long-duration robotic missions exploring the 460°C surface of Venus. Currently, NASA is looking towards SiC-based devices to provide such a solution. However, the current NASA silicon carbide (SiC) JFET device with a channel length of 6 μm (recently fabricated Gen. 11 ICs) limits mission-relevant circuit capabilities. In this study, we combined experiments with simulations to explore two straightforward fabrication strategies (shallow n− and deep n+) to reduce the SiC JFET channel length while maintaining turn-off behavior needed to realize 500 °C circuit operation. First, the material properties for 4H-SiC were implemented in COMSOL and the Poisson equation was solved for twelve 2D device designs. Then, based on the insights gained from the distribution of the electron concentration, electrostatic potential, and electric field for twelve designs (with three fabrication strategies), simulation for a 1 μm gate length nJFET with the turn-off performance comparable to the state-of-the-art.

4H-SiC nJFET↗
NASA NTRSDate not supplied

DC Modeling of 4H-SiC nJFET Gate Length Reduction at 500°C

The development of robust, high-performance integrated circuits (ICs) will enable numerous potential NASA missions of current interest, including long-duration robotic missions exploring the 460°C surface of Venus. Currently, NASA is looking towards SiC-based devices to provide such a solution. However, the current NASA silicon carbide (SiC) JFET device with a channel length of 6 μm (recently fabricated Gen. 11 ICs) limits mission-relevant circuit capabilities. In this study, we combined experiments with simulations to explore two straightforward fabrication strategies (shallow n− and deep n+) to reduce the SiC JFET channel length while maintaining turn-off behavior needed to realize 500 °C circuit operation. First, the material properties for 4H-SiC were implemented in COMSOL and the Poisson equation was solved for twelve 2D device designs. Then, based on the insights gained from the distribution of the electron concentration, electrostatic potential, and electric field for twelve designs (with three fabrication strategies), simulation for a 1 μm gate length nJFET with the turn-off performance comparable to the state-of-the-art.

4H-SiC nJFET↗