Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Growth efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

MOCVD Growth and Characterization of Wide Bandgap ZnGeN 2 Thin Films

ZnGeN 2 is a wide bandgap material having less than 0.1% lattice mismatch with GaN and bandgap within few percent of that of GaN. Based on the first principle calculations, the valence band of ZnGeN 2 is situated ~1.4 eV above that of GaN at the heterointerface. Such a staggered band alignment between two closely lattice matched materials has already been demonstrated promising for novel optoelectronic device designs, for example, high efficiency blue and green light emitting diodes. However, the research on ZnGeN 2 is yet to pass the inceptive period. We report on the growth of single crystalline ZnGeN 2 films using metalorganic chemical vapor deposition and investigation on the crystalline, optical, electrical properties. Diethylzinc (DEZn), germane (GeH 4 ) and ammonia were used as the precursors for Zn, Ge and N, respectively. Films were grown on GaN and sapphire substrates. The Zn/Ge atomic ratio in the films determined from energy dispersive X-ray spectroscopy was found to decrease with increase in growth temperature but to increase with increase in pressure and DEZn/GeH 4 molar flow rate ratio. The X-ray diffraction (XRD) 2θ-ω spectra of the single crystalline ZnGeN 2 films resembled those of orthorhombic (perfectly ordered cations) or distorted wurtzite (disordered cations) polymorphs. High resolution scanning transmission electron microscopy imaging was used to further investigate the crystalline quality and crystalline structure of the films. The single crystalline films on c-sapphire or GaN substrates were found to have planar surface from scanning electron micrographs while those on r-sapphire substrate had stepped surface. No near band edge peak but a broad peak at ~2.05 eV was observed in the photoluminescence (PL) spectra, which was attributed to the transitions involving deep level defects. The PL excitation spectra peaked around 3.4 eV, which is due to the enhanced absorption of photons having energy close to the band gap. The as grown films were found to be n-type with 10 18 – 10 19 cm -3 carrier densities and mobility up to 17 cm 2 /V·s. In the end, the advancement made in this work regarding the growth of ZnGeN 2 thin films is a footstep towards the understanding of the material itself and in turn, towards the implementation of ZnGeN 2 based novel device designs.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Klickitat Valley Health Central Utility Plant Modernization

This project replaced legacy heating and cooling equipment at Klickitat Valley Health (KVH), a rural hospital in Goldendale, Washington. Work included constructing a new chiller building, installing modern hydronic piping systems, replacing the main Emergency Department air handler (Air Handlining Unit (AHU-1)), upgrading electrical systems, and converting the Emergency Department wing from electric reheat to hydronic heating and cooling. Commissioning, testing, adjusting, and balancing were completed under this grant. These upgrades improve energy efficiency, operational resilience, and system reliability while preparing the campus for future electrification and renewable energy integration. They also support growth in healthcare services for a rural population. The project directly reduces energy costs and provides a foundation for future decarbonization measures, including a FEMA-funded microgrid and a large-scale ground source heat pump (GSHP) project. These follow-on initiatives would not have been possible without the hydronic backbone built through this project.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2026

Co 2 P-Pt Heterostructure Interfaces for Electrocatalytic Hydrogen Evolution

Pt-based electrocatalysts are effective for the hydrogen evolution reaction (HER); however, their limited ability to facilitate water dissociation and suboptimal hydrogen binding energy (H BE ) in alkaline electrolytes result in slow reaction kinetics, which hinders their cost-efficiency and practical applications. This study reports the synthesis of Co 2 P-Pt heterostructure nanorods using a seed-mediated growth method, producing a high density of Co 2 P-Pt interfacial sites. Density functional theory (DFT) calculations indicate that electronic interactions at these interfaces optimize H BE on Pt, while the interfacial sites promote water dissociation. The Co 2 P-Pt nanorods demonstrate an overpotential of 14 mV at 10 mA cm −2 for the HER, highlighting the potential of precisely engineered metal-metal phosphide interfaces for enhancing electrocatalytic efficiency.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Quantifying Energy Storage Density Utilization Trends in Redox Flow Battery Chemistries

The transition to new energy resources is driving the need for efficient energy storage. Redox flow batteries (RFBs) are a promising solution due to their flexible design and safer materials, particularly for long-duration storage applications. Despite these advantages, RFB technologies still have considerable room for growth in terms of utilizing all of their available energy storage density. Herein, we assess RFB energy storage density utilization trends for multiple chemistries by accounting for their unique thermodynamic limits, energy efficiencies, and charge capacity constraints. Of the RFBs chemistries analyzed, most still use less than 60% of their theoretical energy storage capacity. The conventional all-vanadium RFB was the closest to its thermodynamic limit available. Moreover, the volumetric footprint and electrolyte cost analyses demonstrate the real-world implications of these inefficiencies. This analysis further indicates that future studies would benefit from clearer reporting of two key quantities: discharge efficiency, which is more directly tied to practically recoverable energy density than round-trip energy efficiency, and state-of-charge or capacity-utilization limits, which govern access to theoretical storage capacity. More consistent reporting of these factors would improve the accuracy and comparability of energy storage utilization analyses across RFB chemistries.

battery energy storage↗
DOE OSTI2022

Two Co-occurring Liana Species Strongly Differ in Their Hydraulic Traits in a Water-Limited Neotropical Forest

Lianas are a key growth form in tropical forests. They are believed to be strong competitors for water, thanks to their presumed efficient vascular systems. However, despite being a large polyphyletic group, they are currently often considered as a functionally homogeneous entity. In this study, we challenged this assumption by estimating the variability in hydraulic traits of two common, co-occurring liana species in a water-limited environment, namely, a seasonally dry tropical forest in Costa Rica. We measured vulnerability to embolism at the leaf and branch levels using two different methods (optical and acoustic vulnerability) and found that both species had very different hydraulic properties. Compared to reported P 50 values in literature, we found two extreme P 50 values: a low value for Bignonia diversifolia (−4.30 ± 0.54 MPa at the leaf level; −7.42 ± 0.54 MPa at the branch level) and a high value for Cissus microcarpa (−1.07 ± 0.14 at the leaf level; −1.20 ± 0.05 MPa at the branch level). Furthermore, B. diversifolia had a higher apparent modulus of elasticity in the radial direction (556.6 ± 401.0 MPa) and a variable midday water potential. On the other hand, C. microcarpa had a low apparent modulus of elasticity in the radial direction (37.8 ± 26.3 MPa) and a high branch water content, which enabled the species to keep its water potential stable during the dehydration experiments and during a drought period in the field. This mechanism may enable this species to coexist with species that are more resistant to drought-induced embolisms such as B. diversifolia . Although only two species were studied, considerable overlap was found between the range of hydraulic properties of trees growing in the same location and trees and lianas growing in two forests in Panama. These findings demonstrate that lianas cannot be considered as a homogeneous group and call for further research into the intra-growth form diversity of liana properties.

Coppieters, Kasper↗
DOE OSTI2021

Performance of Subyearling Fall Chinook Salmon Tagged with 8-, 9-, and 12-mm Passive Integrated Transponder Tags in the Snake River

Abstract Inferences based on tagged individuals from a population are limited in part by the minimum size of fish that can be tagged. Smaller tags allow a greater proportion of a population to be represented by tagging and should reduce potential tag effects on fish performance. We evaluated different performance metrics of juvenile fall Chinook Salmon Oncorhynchus tshawytscha tagged with 8-, 9-, and 12-mm PIT tags in the Snake River. We did not find evidence that posttagging mortality of 45–49-mm-FL fish tagged with 8-mm tags was higher than the posttagging mortality of larger fish tagged with 9- and 12-mm tags. The incisions of fish tagged with 8-mm tags using 14-guage needles healed faster than those of fish tagged with larger tags using 12-guage needles. For individuals that received 8-mm tags, growth in length and mass was higher for 45–49-mm fish than for 50–59-mm fish and 60-mm and larger fish. Growth of the larger size-classes (50–59 and ≥60 mm) was also generally higher for those tagged with 8-mm tags compared to those tagged with 9- and 12-mm tags, respectively. There were no strong relationships between tag burden (i.e., tag weight expressed as a percentage of fish weight) at the time of tagging and growth metrics for any tag size or fish size-class. Releases made to compare the detection efficiency of the three tag types in the juvenile fish bypass at Lower Granite Dam, Washington, showed that 99–100% of all fish were detected. Survival of fish from rearing areas to Lower Granite Dam generally increased with fish size and varied by year, but there was no strong evidence of a tag size effect. The 8-mm PIT tag allowed us to represent a larger portion (i.e., 6.2–24.1%) of the subyearling fall Chinook Salmon population in the Snake River without compromising fish performance or detectability at the dam.

Tiffan, Kenneth F.↗
DOE OSTI2026

Liquified SO 2 induced solid/cathode electrolyte interphase for lithium ion batteries

Formation of robust solid/cathode electrolyte interphases (S/CEI) is vital for long-term stability and high-performance operation of lithium-ion batteries (LIBs), particularly under high voltage regimes. However, engineering electrochemically stable S/CEIs that effectively suppress interfacial side reactions remains a key challenge. Herein, we introduce a liquefied sulfur dioxide (SO 2 )– ionic liquid complex as a fluorine-free multifunctional electrolyte additive for the first time that significantly improves the formation of sulfate/sulfite-rich S/CEI layers at both graphite and NMC811 interfaces. The unique SO 2 -N coordination with a 1,2,4-triazolide-based ionic liquid enables homogeneous SO 2 dissolution, resulting in controlled SO 2 decomposition during the initial electrochemical cycle. This decomposition yields sulfur-rich interphase species that stabilize the electrolyte-electrode interface, reduce impedance growth, and lessen electrolyte decomposition. Electrochemical tests show significantly improved cycle life, reduced polarization, and increased Coulombic efficiency for both anodes and cathodes. XPS confirms the presence of SO 2 -derived surface species that contribute to interfacial stability. In conclusion, this approach highlights a new direction for interphase engineering using liquefied gas additives and opens pathways for sulfur-based S/CEI chemistry in advanced battery systems.

Graphite↗
DOE OSTI2025

Let’s Get Real: Are Wearable Plant Sensors Ready for Crop Monitoring?

In recent years, the number of publications describing new and exciting developments in wearable plant sensors (WPSs) has skyrocketed. These small, lightweight sensors hold promise to assist precision agriculture and may thus help reduce crop losses, increase resource use efficiency, and automate crop production. However, WPSs are often not adequately tested in environments relevant for crop growth, and the majority of experimental WPS studies reveal a glaring lack of basic knowledge of plant biology. This review aims to bridge the communication gap between WPS developers and the wider plant research community by (1) providing essential physiological and environmental background information for engineers in relation to WPS sensing capabilities, (2) offering a step-by-step guide to conduct sensor tests on plants correctly, and (3) highlighting potential challenges and suggesting WPS applications in the open field, greenhouses, and vertical farming systems. We hope this review facilitates the development of WPSs and guides them to be truly “ready for the world”.

crop monitoring↗
DOE OSTI2022

Unconventional excited-state dynamics in the concerted benzyl (C7H7) radical self-reaction to anthracene (C14H10)

Abstract Polycyclic aromatic hydrocarbons (PAHs) are prevalent in deep space and on Earth as products in combustion processes bearing direct relevance to energy efficiency and environmental remediation. Reactions between hydrocarbon radicals in particular have been invoked as critical molecular mass growth processes toward cyclization leading to these PAHs. However, the mechanism of the formation of PAHs through radical – radical reactions are largely elusive. Here, we report on a combined computational and experimental study of the benzyl (C 7 H 7 ) radical self-reaction to phenanthrene and anthracene (C 14 H 10 ) through unconventional, isomer-selective excited state dynamics. Whereas phenanthrene formation is initiated via a barrierless recombination of two benzyl radicals on the singlet ground state surface, formation of anthracene commences through an exotic transition state on the excited state triplet surface through cycloaddition. Our findings challenge conventional wisdom that PAH formation via radical-radical reactions solely operates on electronic ground state surfaces and open up a previously overlooked avenue for a more “rapid” synthesis of aromatic, multi-ringed structures via excited state dynamics in the gas phase.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Clean Energy Education and Training Resources and Opportunities in New York's Southern Tier Region

New York's Southern Tier Region is experiencing high growth and investment in the clean energy sector and is anticipating more jobs to come in energy efficiency, renewable energy, and manufacturing in the coming years. The Network for a Sustainable Tomorrow (NEST) is a nonprofit network of programs working to develop a regional backbone system for education and training programs as well as curricula to support the workforce needed for the region's growing industries to succeed. Through its participation in the US Department of Energy's Better Buildings Workforce Accelerator, NEST requested technical assistance in conducting a landscape and needs assessment of the region's existing clean energy education and workforce development assets. This report supports NEST's efforts by providing a baseline of clean energy employment data, an inventory and gap analysis of the education and workforce development assets currently available and serving the Southern Tier Region, and case studies of innovative and successful regional clean energy education and workforce coalitions from around the county.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2021

In Situ X-ray Measurements to Follow the Crystallization of BaTiO 3 Thin Films during RF-Magnetron Sputter Deposition

Here, we report on adding an important dimension to the fundamental understanding of the evolution of the thin film micro structure evolution. Thin films have gained broad attention in their applications for electro-optical devices, solar-cell technology, as well storage devices. Deep insights into fundamental functionalities can be realized via studying crystallization microstructure and formation processes of polycrystalline or epitaxial thin films. Besides the fundamental aspects, it is industrially important to minimize cost which intrinsically requires lower energy consumption at increasing performance which requires new approaches to thin film growth in general. Here, we present a state of the art sputtering technique that allows for time-resolved in situ studies of such thin film growth with a special focus on the crystallization via small angle scattering and X-ray diffraction. Focusing on the crystallization of the example material of BaTiO 3 , we demonstrate how a prototypical thin film forms and how detailed all phases of the structural evolution can be identified. The technique is shaped to enable a versatile approach for understanding and ultimately controlling a broad variety of growth processes, and more over it demonstrate how to in situ investigate the influence of single high temperature sputtering parameters on the film quality. It is shown that the whole evolution from nucleation, diffusion adsorption and grain growth to the crystallization can be observed during all stages of thin film growth as well as quantitatively as qualitatively. This can be used to optimize thin-film quality, efficiency and performance.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Cooling Egypt: Cost and benefits of room air conditioner efficiency improvement in Egypt

Egypt is one of the largest countries in the Middle East and North Africa region with a population of a total of 106 million (as of July 2022). Increasing urbanization, population growth, and increasing temperatures will likely continue to drive demand for electricity from air conditioning, with corresponding negative impacts on the peak load, air quality, and greenhouse gas emissions from refrigerant use and energy consumption. Since 2003, Egypt has adopted a standards and labeling program for various appliances, and has improved its room air conditioner (RAC) energy efficiency requirements in 2016 and 2017. However, its market is still dominated by inefficient fixed-speed drive (FSD) RACs due to a price-sensitive market. Seasonal metrics such as Cooling Season Performance Factor (CSPF) measure the energy efficiency of FSD and variable-speed drive (VSD) RACs on the same scale. Leading markets, most notably China, have already adopted a new MEPS in 2020 and 2022, which align largely with the United for Efficiency (U4E) Model Regulations Guidelines. India has also adopted a CSPF metric. Both India and China are now experiencing (1) increased demand and consumption of higher efficiency VSD RACs, as well as (2) a corresponding drop in prices from the economies of scale of production of these higher efficiency RACs. Because China is a leading manufacturer in the global air conditioner (AC) market, its adoption of the model U4E regulations have effectively raised the energy efficiency of the ACs in the global market. To achieve the benefits of taking a similar approach to Egypt’s market, we offer the following recommendations: 1. Adopt a common metric to measure the efficiency of both FSD and VSD RACs 2. Raise the stringency of MEPS to the level of the U4E Model Regulation Guidelines 3. Restructure the labeling program from the “A++” labeling scheme to a simpler A through E or a star-rating program 4. Strengthen the compliance regime governing the Egyptian AC MEPS 5. Assist small and medium AC manufacturers in Egypt to transition manufacturing lines to produce low-cost, high-efficiency VSD RACs. Adopting these recommendations would reduce Egypt’s electricity consumption to 11 TWh in 2030 and 89 TWh in 2050—with corresponding carbon dioxide (CO2) emissions reductions and avoided generation capacity requirements compared to the baseline.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2023

Clean Energy Employment Impacts

Wind (land-based), solar (photovoltaics), and energy efficiency (buildings) are three key clean energy technologies identified in the NREL State-Level Employment Projections for Four Clean Energy Technologies in 2025 and 2030 report with continued growth potential. This document outlines how communities and regions will experience differing levels of employment impacts due to resource, labor market, and geographic factors.

clean energy↗
DOE OSTI2024

Template-Assisted Growth of High-Quality α-Phase FAPbI 3 Crystals in Perovskite Solar Cells Using Thiol-Functionalized MoS 2 Nanosheets

Formamidinium lead iodide (FAPI) has gained attention for hybrid perovskite solar cell (PSC) applications due to its enhanced stability and narrow bandgap. However, a significant challenge remains in inducing and stabilizing the elusive perovskite “black phase”—photoactive cubic α-FAPI—as the relatively bulky FA + cations tend to favor the thermodynamically stable nonphotoactive “yellow phase”. Here, in this study, we present a templated growth strategy employing thiol-functionalized MoS 2 nanosheets as templates. By introduction of 3-mercaptopropionic acid (MPA)-functionalized MoS 2 as a growth template, precise control over crystal formation was achieved, favoring the growth of high-quality α-FAPI films. These advanced templated films exhibited substantial improvements in charge transport properties, efficient light absorption, and enhanced charge extraction. As a result, the PSCs achieved a significantly enhanced power conversion efficiency (PCE) compared to the nontemplated control device, increasing from 20.6 to 22.5%. The MoS 2 -incorporated device also demonstrated excellent shelf stability, maintaining 91% of the initial PCE even after 1600 h of storage without device encapsulation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

HPRT promotes proliferation and metastasis in head and neck squamous cell carcinoma through direct interaction with STAT3

Highlights: • The higher expression of HPRT in HNSCC tissue was related to poor prognosis of patients. • Overexpression of HPRT increased the gene expression of epithelial mesenchymal transition markers. • HPRT directly interacted with STAT3. • Knocking down HPRT significantly decreased tumour growth and enhanced the anticancer effect against HNSCC xenografts. Increasing effort has been put into finding novel molecular pathways to improve the efficiency of EGFR inhibitors against head and neck squamous cell cancer (HNSCC). In this study, we performed data mining and bioinformatically analysed RNA-Seq data downloaded from TCGA and confirmed that higher expression of HPRT in HNSCC tissue was related to poor prognosis of patients. Then, we conducted in vitro and in vivo loss- and gain-of-function experiments to demonstrate the role of HPRT in HNSCC cell lines. Overexpression of HPRT increased the gene expression of epithelial mesenchymal transition markers via direct interaction with STAT3. Knocking down HPRT significantly decreased tumour growth and enhanced the anticancer effect of EGFR inhibitors against HNSCC xenografts. In conclusion, HPRT is a binding partner of STAT3 that promotes EMT and proliferation. Our findings support HPRT as a promising prognostic indicator and potential therapeutic target for HNSCC.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2021

Tailoring the Surface of Metal Halide Perovskites to Enable the Atomic Layer Deposition of Metal Oxide Contacts

Replacing organic contact layers with inorganic counterparts, such as metal oxides, is one strategy for improving long-term device stability in metal halide perovskite solar cells. Often, the methods used to deposit metal oxide thin films are incompatible with metal halide perovskites, creating challenges for the fabrication of contacts above the perovskite absorber layer. In this study, we utilize a one-step, solution treatment of the top surface of Cs 0.25 FA 0.75 Pb(Br 0.20 I 0.80 ) 3 to create a thin (~1 nm) overlayer of lead sulfide (PbS) to protect the underlying perovskite during subsequent deposition. X-ray characterization of the surface region shows that the PbS overlayer limits undesirable changes to the perovskite structure and stoichiometry during atomic layer deposition (ALD) of SnO 2 . This protection enables ALD growth of SnO 2 electron contacts on top of the perovskite without an organic transport layer (e.g., C 60 ), resulting in a solar cell with a power conversion efficiency of 5.8%. This result is a marked improvement over devices with ALD SnO 2 grown directly on the perovskite without a PbS overlayer, which produce no power output. Furthermore, the interface characterization and device results in this study highlight some of the key challenges associated with ALD metal oxide growth on perovskite materials and can help inform the future design of inorganic contact layer deposition in solar photovoltaic technologies.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Electroactive ZnO: Mechanisms, Conductivity, and Advances in Zn Alkaline Battery Cycling

Zinc oxide is of great interest for advanced energy devices because of its low cost, wide direct bandgap, non-toxicity, and facile electrochemistry. In zinc alkaline batteries, ZnO plays a critical role in electrode passivation, a process that hinders commercialization and remains poorly understood. Here, novel observations of an electroactive type of ZnO formed in Zn-metal alkaline electrodes are disclosed. The electrical conductivity of battery-formed ZnO is measured and found to vary by factors of up to 10 4 , which provides a first-principles-based understanding of Zn passivation in industrial alkaline batteries. Simultaneous with this conductivity change, protons are inserted into the crystal structure and electrons are inserted into the conduction band in quantities up to ≈10 20 cm –3 and ≈1 mAh gZnO –1 . Electron insertion causes blue electrochromic coloration with efficiencies and rates competitive with leading electrochromic materials. The electroactivity of ZnO is evidently enabled by rapid crystal growth, which forms defects that complex with inserted cations, charge-balanced by the increase of conduction band electrons. Furthermore, this property distinguishes electroactive ZnO from inactive classical ZnO. Knowledge of this phenomenon is applied to improve cycling performance of industrial-design electrodes at 50% zinc utilization and the authors propose other uses for ZnO such as electrochromic devices.

36 MATERIALS SCIENCE↗