Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Flow battery”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Characterizing the Impact of Oligomerization on Redox Flow Cell Performance

Abstract Redox flow batteries (RFBs) are hindered by complex failure modes, particularly crossover through the membrane, resulting in capacity fade and reduced cycling efficiencies. Redox‐active oligomers (RAOs) have recently been proposed for mitigating this phenomenon while maintaining sufficient transport properties; however, to date, few studies have quantified how the chemical and electrochemical properties of RAOs influence their performance in redox flow cells. Here, we demonstrate that oligomeric derivatives of 2,2,6,6‐tetramethylpiperidine 1‐oxyl (TEMPO) exhibit lower diffusivities than the monomeric species but retain facile charge transfer characteristics. The size‐dependent variations in mass transport rates directly translate to differences in flow cell polarization and symmetric cycling performance. Post‐mortem analyses reveal that oligomerization does not meaningfully alter decay processes as evinced by similar capacity fade across all species. Broadly, these findings corroborate and extend upon previously developed relationships between molecular size, electrochemical properties, and flow cell performance.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Intermetallic Single-Atom Alloy In–Pd Bimetallene for Neutral Electrosynthesis of Ammonia from Nitrate

Harvesting recyclable ammonia (NH 3 ) from the electrocatalytic reduction of nitrate (NO 3 RR) offers a sustainable strategy to close the ecological nitrogen cycle from nitration contamination in an energy-efficient and environmentally friendly manner. The emerging intermetallic single-atom alloys (ISAAs) are recognized to achieve the highest site density of single atoms by isolating contiguous metalatoms into single sites stabilized by another metal within the intermetallic structure, which holds promise to couple the catalytic benefits from intermetallic nanocrystals and single-atom catalysts for promoting NO 3 RR. Herein, ISAA In-Pd bimetallene, in which the Pd single atoms are isolated by surrounding In atoms, is reported to boost neutral NO 3 RR with a NH 3 Faradaic efficiency(FE) of 87.2%, a yield rate of 28.06 mg h -1 mg Pd -1 , and an exceptional electrocatalytic stability with increased activity/selectivity over 100 h and 20 cycles. The ISAA structure induces substantially diminished overlap of Pdd-orbitals and narrowed p-d hybridization of In-p and Pd-d states around the Fermi level, resulting in a stronger NO 3 - adsorption and a depressed energy barrier of the potential-determining step for NO 3 RR. Finally, further integrating the NO 3 RR catalyst into a Zn-NO 3 - flow battery as the cathode delivers a power density of 12.64 mW cm -2 and a FE of 93.4% for NH 3 production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

3D printed optimized electrodes for electrochemical flow reactors

Recent advances in 3D printing have enabled the manufacture of porous electrodes which cannot be machined using traditional methods. With micron-scale precision, the pore structure of an electrode can now be designed for optimal energy efficiency, and a 3D printed electrode is not limited to a single uniform porosity. As these electrodes scale in size, however, the total number of possible pore designs can be intractable; choosing an appropriate pore distribution manually can be a complex task. To address this challenge, we adopt an inverse design approach. Using physics-based models, the electrode structure is optimized to minimize power losses in a flow reactor. The computer-generated structure is then printed and benchmarked against homogeneous porosity electrodes. We show how an optimized electrode decreases the power requirements by 16% compared to the best-case homogeneous porosity. Future work could apply this approach to flow batteries, electrolyzers, and fuel cells to accelerate their design and implementation.

25 ENERGY STORAGE↗
DOE OSTI2020

Single-layer graphene as a highly selective barrier for vanadium crossover with high proton selectivity

In this paper, we report near-zero crossover for vanadium cross-permeation through single-layer graphene immobilized at the interface of two Nafion® polymer electrolyte membranes. Vanadium ion diffusion and migration, including proton mobility through membrane composites, were studied with and without graphene under diffusion and migration conditions. Single-layer graphene was found to effectively inhibit vanadium ion diffusion and migration under specific conditions. The single-layer graphene composites also enabled remarkable ion transmission selectivity improvements over pure Nafion® membranes, with proton transport being four orders of magnitude faster than vanadium ion transport. Resistivity values of 0.02 ± 0.005 Ω cm 2 for proton and 223 ± 4 Ω cm 2 for vanadium ion through single atomic layer graphene are reported. This high selectivity may have significant impact on flow battery applications or for other electrochemical devices where proton conductivity is required, and transport of other species is detrimental. Our results emphasize that crossover may be essentially completely eliminated in some cases, enabling for greatly improved operational viability.

2D nanomaterial↗
DOE OSTI2020

Competitive Pi-Stacking and H-Bond Piling Increase Solubility of Heterocyclic Redoxmers

Redoxmers are organic molecules that carry electric charge in flow batteries. In many instances, they consist of heteroaromatic moieties modified with appended groups to prevent stacking of the planar cores and increase solubility in liquid electrolytes. This higher solubility is desired as it potentially allows achieving greater energy density in the battery. However, the present synthetic strategies often yield bulky molecules with low molarity even when they are neat and still lower molarity in liquid solutions. Fortunately, there are exceptions to this rule. Here, we examine one well-studied redoxmer, 2,1,3-benzothiadiazole, which has solubility similar to 5.7 M in acetonitrile at 25 degrees C. We demonstrate computationally and prove experimentally that the competition between two packing motifs, face-to-face it-stacking and random N-H bond piling, introduces frustration that confounds nucleation in crowded solutions. Our findings and examples from related systems suggest a complementary strategy for the molecular design of redoxmers for high energy density redox flow cells.

25 ENERGY STORAGE↗
DOE OSTI2022

Preactivated zeolite nanosheet plate-tiled membrane on porous PVDF film: Synthesis and study of proton-selective ion conduction

Preactivated MFI zeolite nanosheet plates (ZNPs) with large areas (~2.0 × 2.0 μm 2 ) and nanometer thicknesses (~60 nm) were prepared directly in liquid-dispersed state. The individual ZNP was a stack of 4-nm-thick single crystalline zeolite nanosheets (ZNs) interlinked by Si–O–Si bonds between neighboring ZN surfaces. The dispersed open-pore ZNPs allowed formulating suspensions for tiling ZNP membranes on polymer substrates without requiring post-coating activation. A pinhole-free ZNP-tiled (ZNPT) membrane has been achieved on macroporous PVDF film by a self-repairing vacuum-assisted filtration coating method. The resultant ZNPT layer was ~500 nm-thick consisting of about 7 ZNP layers with inter-ZNP width and inter-ZNP entrance porosity around 9 nm and 2%, respectively. The ZNPT-PVDF membrane exhibited high selectivity to proton transport over vanadyl ion and low resistances to proton conduction in aqueous solutions. The membrane also demonstrated to function as an efficient ion separator for the vanadium redox flow battery. The reported synthesis of preactivated ZNP suspension may overcome the major hurdle to realizing polymer-supported ZN membranes, which is the inefficiency of existing methods in obtaining readily dispersible open-pore ZNs. Finally, the ZNPT-PVDF membrane can be a more affordable and sustainable alternative to the Nafion-based ion separation membranes.

36 MATERIALS SCIENCE↗
DOE OSTI2023

High Ion Conductive and Selective Membrane Achieved through Dual Ion Conducting Mechanisms

Conventional ion-selective membranes, that is ion-exchange and porous membranes, are unable to perform high conductivity and selectivity simultaneously due to the contradictions between their ion selecting and conducting mechanisms. Here, in this work, a bifunctional ion-selective layer is developed via the combination of nanoporous boron nitride (PBN) and ion exchange groups from Nafion to achieve high ion conductivity through dual ion conducting mechanisms as well as high ion selectivity. A template-free method is adopted to synthesize flake-like PBN, which is further enmeshed with Nafion resin to form the bifunctional layer coated onto a porous polyetherimide membrane. The double-layer membrane exhibits excellent ion selectivity (1.49 × 10 8 mS cm –3 min), which is 22 times greater than that of the pristine porous polyetherimide membrane, with outstanding ion conductivity (64 mS cm –1 ). In a vanadium flow battery, the double-layer membrane achieves a high Coulombic efficiency of 97% and outstanding energy efficiency of 91% at 40 mA cm –2 with a stable cycling performance for over 700 cycles at 100 mA cm –2 . PBN with ion exchange groups may therefore offer a potential solution to the limitation between ion selectivity and conductivity in ion-selective membranes.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Novel Technique for Developing Linearized Convex System Models from Experimentally Derived Data

This paper presents a novel technique for generating a convex system model from an experimentally derived data set which features variance among repeated measurements. The convex system model developed as a test case characterizes the dynamic system losses of a vanadium redox flow battery as a function of the active power output and the battery state of charge. The technique hinges on a pre-cleaning via clustering procedure which precedes the formation of a planar convex hull comprised of triangular simplices. The clustering procedure efficiently reduces the experimental data set while mitigating variance among repeated measurements and removes outliers. Ultimately, the lower evelope of the planar convex hull serves as the desired convex system model. The proposed technique reduces systematic model error which is otherwise present when directly developing a planar convex hull model based on an unreduced data set.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2024

ACS Spotlight: Bipolar Membranes for Electrochemical Energy Conversion, Chemical Manufacturing, and Separations

Sustainable energy conversion, chemical manufacturing, and separations are central to addressing the world’s energy and environmental challenges. Electrochemical platforms stand as a cornerstone in addressing these challenges because they are low exergy and can be powered on renewable electrons. In electrochemical systems, bipolar membranes (BPMs) are emerging as a unique class of ion exchange membranes poised to revolutionize various electrochemical processes via pH control of anode and cathode chambers and in situ pH adjustment. In this Spotlight Review, we provide a comprehensive review of electrochemical platforms utilizing BPMs for energy conversion (water electrolyzers for hydrogen production, fuel cells, and flow batteries), chemical manufacturing (electrolyzers that convert carbon dioxide into value-added chemicals and nitrate into ammonia), and separations. The motivation for using BPMs, as well as their performance and durability, in electrochemical platforms are disseminated. We also discuss current challenges that impede BPM electrochemical systems from competing with state-of-the-art electrochemical systems using monopolar ion-exchange membranes (e.g., anion/hydroxide exchange membranes and cation/proton exchange membranes). Here, the review also covers molecular modeling and continuum modeling efforts to understand the basic mechanisms that govern BPM performance.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2025

Controlled phosphate doping into nanoscopic SiO 2 proton conducting membranes

This article describes a method to introduce phosphate (PO 4 ) into SiO 2 atomic layer deposition (ALD) films in a self-limiting fashion. The method involves the use of a less common phosphate precursor, trimethyl phosphite [P(OMe) 3 ], to introduce PO 4 as a low-level dopant, <1 at. %, into a SiO 2 ALD process using bis(ethylmethylamino)silane and a modified O 3 conversion. P(OMe) 3 does not deposit a film with typical oxygen sources but incorporates as PO 4 in an ABC-type ALD scheme at deposition temperatures ranging from 100 to 300 °C. Addition of up to ∼1 at. % of PO 4 does not significantly impact the film density or concentrations of carbon and nitrogen impurities, which are both <0.4 at. %. Despite the relatively low dopant concentrations, PO 4 incorporation is shown to have a large impact on transport properties of the film. When explored as proton (H + )-conducting membranes, undoped SiO 2 ALD films showed H + conductivities (3 × 10 −6 –8 × 10 −5 S cm −1 ) and low H 2 permeabilities (<10 −9 cm 2 s −1 ) when measured at room temperature. The addition of PO 4 is shown to increase H + conductivity to 2 × 10 −4 S cm −1 , while maintaining low H 2 permeability of <10 −9 cm 2 s −1 . The ratio of H + conductivity to H 2 permeability, a key performance metric for H + -conducting membranes used in water electrolyzers, exceeds that of commercial Nafion-117 membranes. Here, the moderate H + conductivity and very low H 2 permeability of PO 4 -doped SiO 2 films make them promising candidates as fluorine-free replacements for Nafion in applications such as water electrolysis, hydrogen fuel cells, and redox flow batteries.

Atomic layer deposition↗
DOE OSTI2024

Insights into the interaction of nitrobenzene and the Ag(111) surface: A DFT study

Here, this study explores the potential of nitrobenzene as an anolyte material for nonaqueous redox flow batteries (RFBs) by theoretically examining its low-coverage adsorption behavior on neutral and charged Ag(111) model electrode surfaces. At the low coverage limit, DFT calculations show a preference for nitrobenzene to adsorb parallel to the surface, with the benzene ring and nitro group centered over HCP sites. Interactions between nitrobenzene and the surface were analyzed using induced charge density analysis, Bader charge analysis, and projected density of states (PDOS). It was found that nitrobenzene adsorbs primarily through van der Waals interactions with the surface. As nitrobenzene accumulates negative charge, the strength of adsorption diminishes. Understanding the electrode-electrolyte interface is crucial for enhancing RFB electrochemical performance, and this study sheds light on nitrobenzene's interaction with a model Ag electrode.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Synthesis of Alkoxy-TEMPO Aminoxyl Radicals and Electrochemical Characterization in Acetonitrile for Energy Storage Applications

In this paper, we describe the synthesis and characterization of alkoxylated TEMPO, (2,2,6,6-tetramethylpiperidin-1-yl)oxyl, radicals with potential application in organic non-aqueous redox flow batteries. The behavior of a series of TEMPO derivatives with varying lengths of alkoxy chain is analyzed in acetonitrile solutions using electrochemistry techniques, electron paramagnetic resonance (EPR) spectroscopy, and measurements of permeability through three different membranes. Electrochemical redox potentials are only weakly dependent on the substituent, but, in contrast, exchange current densities derived from the data do depend on the substitution. EPR lends further insight into these properties via the determination of hyperfine splitting constant and rotational correlation time. There is a negligible effect of the substituents on those parameters among the modified TEMPO radicals. Finally, permeation rates of modified TEMPO derivatives through membranes depend significantly on both the membrane and the substitution of TEMPO, providing insights into capacity fade measurements in the literature.

25 ENERGY STORAGE↗
DOE OSTI2023

Concentration‐dependent Cycling of Phenothiazine‐based Electrolytes in Nonaqueous Redox Flow Cells

Increasing redox-active species concentrations can improve viability for organic redox flow batteries by enabling higher energy densities, but the required concentrated solutions can become viscous and less conductive, leading to inefficient electrochemical cycling and low material utilization at higher current densities. To better understand these tradeoffs in a model system, we study a highly soluble and stable redox-active couple, N-(2-(2-methoxyethoxy)ethyl)phenothiazine (MEEPT), and its bis(trifluoromethanesulfonyl)imide radical cation salt (MEEPT-TFSI). We measure the physicochemical properties of electrolytes containing 0.2–1 M active species and connect these to symmetric cell cycling behavior, achieving robust cycling performance. Specifically, for a 1 M electrolyte concentration, we demonstrate 94% materials utilization, 89% capacity retention, and 99.8% average coulombic efficiency over 435 h (100 full cycles). This demonstration helps to establish potential for high-performing, concentrated nonaqueous electrolytes and highlights possible failure modes in such systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Multifaceted effects of ring fusion on the stability of charged dialkoxyarene redoxmers

Due to their almost unlimited scalability, redox flow batteries can make versatile and affordable energy storage systems. Redox active materials (redoxmers) in these batteries largely define their electrochemical performance, including the life span of the battery that depends on the stability of charged redoxmers. Here, in this study, we examine the effects of expanding the pi-system in the arene rings on the chemical stability of dialkoxyarene redoxmers that are used to store positive charge in RFBs. When 1,4-dimethoxybenzene is pi-extended to 1,4 dimethoxynaphthalene, a lower redox potential, improved kinetic stability, and longer cycling life are observed. However, when an additional ring is fused to make 9,10-dimethoxyanthracene, the radical cation undergoes rapid O -dealkylation possibly due to increased steric strain that drives methoxy out of the arene plane thus breaking the pi-conjugation with O 2p orbitals. On the other hand, the planar structure of 1,4-dimethoxynaphthalene may facilitate second -order reactions of radical cations leading to their neutralization in the bulk. Our study suggests that extending the pi-system changes reactivity in multiple (sometimes, opposite) ways, so lowering the oxidation potential through pi-conjugation to improve redoxmer stability should be pursued with caution.

25 ENERGY STORAGE↗
DOE OSTI2020

Self-Assembled Solute Networks in Crowded Electrolyte Solutions and Nanoconfinement of Charged Redoxmer Molecules

Redoxmers are electrochemically active organic molecules storing charge and energy in electrolyte fluids circulating through redox flow batteries (RFBs). Such molecules typically have solvent-repelling cores and solvent-attracting pendant groups introduced to increase solubility in liquid electrolytes. These two features can facilitate nanoscale aggregation of the redoxmer molecules in crowded solutions. In some cases, this aggregation leads to the emergence of continuous networks of solute molecules in contact, and the solution becomes microscopically heterogeneous. In this study, we used small-angle X-ray scattering (SAXS) and molecular dynamics modeling to demonstrate formation of such networks and examine structural factors controlling this self-assembly. We also show that salt ions become excluded from these solute aggregates into small pockets of electrolytes, where these ions strongly associate. This confinement by exclusion is also likely to occur to charged redoxmer molecules in a “sea” of neutral precursors coexisting in the same solution. Here, we demonstrate that the decay lifetime of the confined charged molecules in such solutions can increase several fold compared to dilute solutions. We attribute this behavior to a “microreactor effect” on reverse reactions of the confined species during their decomposition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Mechanistic Study of Controlled Zinc Electrodeposition Behaviors Facilitated by Nanoscale Electrolyte Additives at the Electrode Interface

Nanoparticle organic hybrid materials (NOHMs) are liquid-like materials composed of an inorganic core to which a polymeric canopy is ionically tethered. NOHMs have unique properties including negligible vapor pressure, high oxidative thermal stability, and the ability to bind to reactive species of interest due to the tunability of their polymeric canopy. This makes them promising multifunctional materials for a wide range of energy and environmental technologies, including electrolyte additives for electrochemical energy storage (e.g., flow batteries) and the electrochemical conversion of CO 2 to chemicals and fuels. Due to their unique transport behaviors in fluid systems, an understanding of the near-electrode surface behavior of NOHMs in electrolyte solutions and their effect on electrochemical reactions is still lacking. In this work, the complexation of zinc (Zn) by NOHMs with an ionically tethered polyetheramine canopy (HPE) (NOHM-I-HPE) was studied using attenuated total reflectance Fourier transform infrared and Carbon-13 nuclear magnetic resonance spectroscopy. Additionally, various electrochemical techniques were employed to discern the role of NOHM-I-HPE during zinc electrodeposition, and the results were compared to those of the electrochemical system containing untethered HPE polymers. Our findings confirmed that NOHM-I-HPE and HPE reversibly complex zinc in the aqueous electrolyte. NOHM-I-HPE and HPE were found to block some of the electrode active sites, reducing the overall current density during electrodeposition, while facilitating the formation of smooth zinc deposits, as revealed by surface imaging and diffraction techniques. Observed variations in the current density responses and the degree of passivation created by the NOHM-I-HPE and HPE adsorbed on the electrode surface revealed that their different packing behaviors at the electrode–electrolyte interface influence the zinc deposition mechanism. The presence of the nanoparticle and ordering offered by the NOHMs as well as the structured conformation of the polymeric canopy allowed the formation of void spaces and free volumes for enhanced transport behaviors. Furthermore, these findings provided insights into how structured electrolyte additives such as NOHMs can allow for advancements in electrolyte design for controlled deposition of metal species from energy-dense electrolytes or for other electrochemical reactions.

25 ENERGY STORAGE↗
DOE OSTI2025

Automation-Accelerated Electrolyte Design Mitigates Solubility Competition between Redox-Active Molecules and Supporting Salts

In nonaqueous redox-flow batteries (NRFBs), redox-active organic molecules (ROMs) and supporting salts compete for solvation sites, limiting achievable energy density. We combine automated high-throughput experimentation (HTE) with camera-based saturation monitoring and quantitative NMR to measure paired (ROM, salt) solubilities across single and mixed organic solvents. Using 2,1,3-benzothiadiazole (BTZ) with lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) as a model system, we find that a binary m-xylene/acetonitrile mixture dissolves ≈3 M of both BTZ and LiTFSI─surpassing the previously reported 2 M ceiling for neat acetonitrile─by leveraging complementary solvation (MX is BTZ-philic and salt-phobic; ACN stabilizes LiTFSI). A random-forest model (RMSE ≈ 0.24) trained on solvent descriptors highlights log P and salt concentration as dominant predictors and predicts MX/ACN ≈0.3/0.7 (v/v) to be near-optimal. These formulations retain practical viscosity and ∼5 mS·cm –1 conductivity at high loading. In conclusion, the workflow provides a reproducible, data-centric route to NRFB electrolyte design and motivates an open, standardized dual-solute solubility resource for accelerated electrolyte discovery.

Electrolytes↗
DOE OSTI2020

Energy Storage Analysis

This study presents a comprehensive techno-economic characterization of energy storage and exible low carbon power generation technologies that can shift energy across days, weeks, or months to balance daily, weekly, and seasonal disparities in supply and demand. Energy storage technologies evaluated here include pumped hydropower storage (PHS), adiabatic and diabatic compressed air energy storage (CAES), vanadium redox flow batteries (VRBs), pumped thermal energy storage (P-TES), and renewably produced hydrogen stored in either geologic formations or underground pipes with re-electrification via combustion turbines in combined cycles, stationary proton exchange membrane (PEM) fuel cells, or the novel use of PEM fuel cells designed for heavy-duty vehicles (HDVs) which are expected to have shorter lives but also lower capital costs. We also evaluate flexible low-carbon power generation systems, including ethanol combustion in gas turbines and natural gas combustion with carbon capture and sequestration (CCS). We estimate current costs with literature data, use learning rates to characterize future costs, and develop capacity factors calibrated to an 85% renewables grid to calculate the levelized cost of energy (LCOE) of each technology. Results illustrate that at the 12-hour storage duration, PHS and CAES have the lowest LCOE with current costs, and VRBs become competitive if future costs are achieved. At the 120-hour storage duration, hydrogen systems with geologic storage and natural gas with CCS achieve the lowest LCOE in both current and future capital cost scenarios. In particular, the new configuration of HDV-PEM fuel cells with hydrogen storage in geologic formations evaluated here could lower the LCOE by 22-27% compared to stationary fuel cell systems typically evaluated and might help enable very high (>80%) renewable energy electric power systems. P-TES and hydrogen stored in underground pipes are the least-cost options at the 120-hour storage duration rating that do not require some form of geologic storage. Sensitivity analysis and Monte Carlo analysis illustrate that the general trends seen in this study are valid for a wide range of capacity factors and future cost scenarios. The study also illustrates that coproducing and selling hydrogen to other markets could reduce the LCOE of hydrogen systems by up to 39%.

carbon capture and sequestration↗