SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The thin-layer Navier-Stokes equations are coupled with a zonal scheme (or domain-decomposition method) to develop the Transonic Navier-Stokes (TNS) wing-alone code. The TNS has a total of 4 zones and is extended to a total of 16 zones for the wing-fuselage version of the code. Results are compared on the Cray X-MP-48 and compared with experimental data.
Graphite-epoxy frames were drop tested onto a concrete floor to simulate crash loadings. The frames have Z-shaped cross sections typical of designs often proposed for fuselage structure of advanced composite transports. A diameter of six feet for the frames was chosen to reduce specimen fabrication costs and to facilitate testing. Accelerometer, strain gage, and photographic measurements are presented which characterize the impact behavior of frames with differing masses to represent structural or seat/occupant masses. Failures of the graphite-epoxy frames involved complete separations through the cross section. All damage to the lightly loaded composite frames was confined to an area close to the impact point. Subsequent failures left and right of the impact point occurred for the more heavily loaded specimens.
In-flight measurements of propeller noise on the fuselage of an OV-10A aircraft were obtained using a horizontal and a vertical microphone array. A wide range of flight conditions were tested including changes in angle of attack, sideslip angle, power coefficient, helical tip Mach number and advance ratio, and propeller direction of rotation. Results show a dependence of the level and directivity of the tones on the angle of attack and on the sideslip angle with the propeller direction of rotation, which is similar to results obtained in wind tunnel tests with advanced propeller designs. The level of the tones at each microphone increases with increasing angle of attack for inboard-down propeller rotation and decreases for inboard-up rotation. The level also increases with increasing slideslip angle for both propeller directions of rotation. Increasing the power coefficient results in a slight increase in the level of the tones. A strong shock wave is generated by the propeller blades even at relatively low helical tip Mach numbers resulting in high harmonic levels. As the helical tip Mach number and the advance ratio are increased, the level of the higher harmonics increases much faster than the level of the blade passage frequency.
The thin-layer Navier-Stokes equations are coupled with a zonal scheme (or domain-decomposition method) to develop the Transonic Navier-Stokes (TNS) wing-alone code. TNS has a total of four zones and is extended to a total of 16 zones for the wing-fuselage version of the code. Results are computed on the Cray X-MP-48 and compared with experimental data.
Laminar flow control and drag reduction research requires accurate boundary layer solutions as input to the three-dimensional stability analysis procedures currently under development. In support of these major programs, a fourth-order accurate finite difference scheme for solving the three-dimensional, compressible boundary layer equations has been developed and is presented in this paper. The method employs a two-point scheme in the wall normal direction and second order zigzag scheme in the cross flow direction. Accurate procedures to interface with the inviscid results are also presented. The results of applying the procedure to laminar flow on wings and fuselages are presented.
As part of the NASA High Alpha Technology Program, fine-grid Navier-Stokes solutions have been obtained for flow over the fuselage forebody and wing leading-edge extension of the F/A-18 High Alpha Research Vehicle at large incidence. The resulting flows are complex and exhibit cross-flow separation from the sides of the forebody and from the leading-edge extension. A well-defined vortex pattern is observed in the leeward-side flow. Results obtained for laminar flow show good agreement with flow visualizations obtained in ground-based experiments. Further, turbulent flows computed at high-Reynolds-number flight-test conditions show good agreement with surface and off-surface visualizations obtained in flight.
An investigation was conducted in the Langley Spin Tunnel to measure the pressures on the surface of the horizontal and vertical tail and the aft fuselage of an aircraft model. The pressures were measured on a model of a proposed Australian Primary Trainer airplane configuration while the model was rotating at spinning attitudes. The test results indicate that the presence of the horizontal tail adversely modifies the surface pressure on the vertical tail. The presence of the wing also adversely modifies the pressures on the horizontal and vertical tails.
An optimization method has been developed to design axisymmetric body shapes such as fuselages, nacelles, and external fuel tanks with increased transition Reynolds numbers in subsonic compressible flow. The new design method involves a constraint minimization procedure coupled with analysis of the inviscid and viscous flow regions, and linear stability analysis of the compressible boundary layer. Boundary-layer transition is predicted by a 'hybrid' transition criterion based on Granville's transition criterion and a criterion using linear stability theory coupled with the e(n)-method. A tiptank of a business-jet is used as an example to illustrate that the method can be utilized to design an axisymmetric body shape with extensive natural laminar flow. Boundary layer transition is predicted to occur at a transition Reynolds number of 6.04 x 10 to the 6th on the original tiptank. On the designed body shape, a transition Reynolds number of 7.22 x 10 to the 6th is predicted using compressible linear stability theory coupled with e(n)-method.
Numerical solutions of the three-dimensional, compressible laminar boundary-layer equations for a general aviation fuselage are presented. The numerical procedure is second-order accurate and independent of the cross-flow velocity direction. Numerical results are presented for a Mach number and unit Reynolds number of 0.3 and 7 x 10 to the 6th/m, respectively, for angles of attack of 0 and 3 deg. Comparisons are made between results obtained using a general nonorthogonal curvilinear body oriented coordinate system and a streamline coordinate system. Axisymmetric analogue results are also compared with the three-dimensional solutions.
Fine-grid Navier-Stokes solutions were obtained for flow over the fuselage forebody and wing leading edge extension of the F/A-18 High Alpha Research Vehicle at large incidence. The resulting flows are complex, and exhibit cross flow separation from the sides of the forebody and from the leading edge extension. A well-defined vortex pattern is observed in the leeward-side flow. Results obtained for laminar flow show good agreement with flow visualizations obtained in ground-based experiments. Further, turbulent flows computed at high Reynolds-number flight-test conditions show good agreement with surface and off-surface visualizations obtained in flight.
With the characteristics of high strength/weight and stiffness/weight ratios in advanced composite materials, composite plate structures have been successfully applied to secondary load-carrying structural components in the aerospace industry for the past two decades. Recently, filament wound composite shells are being considered for design of primary fuselage structures. To implement the design the structural response under various loading conditions needs to be predicted accurately. Therefore, it is essential to establish a rigorous analytical solution in the area of composite laminated shells. A closed form solution is presented that predicts the response of a composite shell subjected to internal pressure, axial tension, bending, and torsion. The material of the shell is assumed to be general cylindrically anisotropic. Based on the theory of cylindrical anisotropic elasticity coupled partial differential governing equations are developed using Lehknitskii's stress function approach. The general expressions for the stresses and displacements in the composite cylinders under these loading conditions is discussed. Three examples (45) off-axis unidirectional, (45/45) unsymmetric, and (45/45)(sub s) symmetric angle-ply fiber-reinforced laminated shells are shown to illustrate the effect of radius-to-thickness ratios, coupling, and stacking sequence.
The overall objective is to identify and understand, via directed experimentation and analysis, the mechanisms which control the structural behavior of fuselages in their response to damage (resistance, tolerance, and arrest). A further objective is to develop straightforward design methodologies which can be employed by structural designers in preliminary design stages to make intelligent choices concerning the material, layup, and structural configuration so that a more efficient structure with structural integrity can be designed and built.
Active control of interior noise in model aircraft fuselages using piezoceramic actuators is experimentally studied. The actuators are bonded directly to the structure and error information is taken from up to two microphones located in the interior acoustic field. The results demonstrate that global attenuation of the order of 10 to 15 dB of interior noise can be achieved with piezoceramic actuators, irrespective of whether the shell system is vibrating at an acoustic or structural resonant frequency. The work also proves that active control using vibration (moment) inputs works well when a floor simulating that of an aircraft is installed in the model. This result suggests that the technique will be successful in controlling interior noise in realistic aircraft structures.
Results from an experimental test undertaken to study the basic noise transmission characteristics of a realistic, built-up composite fuselage model are presented. The floor-equipped stiffened composite cylinder was exposed to a number of different exterior noise source configurations in a large anechoic chamber. These exterior source configurations included two point sources located in the same plane on opposite sides of the cylinder, a single point source and a propeller simulator. The results indicate that the interior source field is affected strongly by exterior noise source phasing. Sidewall treatment is seen to reduce the overall interior sound pressure levels and dampen dominant acoustic resonances so that other acoustic modes can affect interior noise distribution.
A ray acoustics approach to fuselage scattering of rotor noise is considered. The method is based on a combination of classical geometrical acoustics and the paraxial ray approximation. The method can handle scattering by objects of arbitrary shapes and can be applied in an inhomogeneous moving medium. Applications to aeroacoustics include the scattering of blade vortex interaction (BVI) pulses by rigid scattering objects. The BVI is modeled by a rotating impulsive point force. It has been found that scattering effects of rotating sources cannot be ignored. Flow has also been found to cause a modification and displacement of the directivity pattern and the shadow zones behind scatterers.
Three-dimensional thin-layer Navier-Stokes computations are presented for the F/A-18 configuration. The modeled configuration includes an accurate surface representation of the fuselage, leading-edge-extension, as well as the wing with and without leading-edge-flap deflection. A multi-block structured volume grid with various topologies is generated using transfinite interpolation technique. The flowfield domain is divided into twenty blocks, each representing a particular geometrical complexity of the configuration. The results are obtained from an algorithm for solving the compressible Navier-Stokes equations that incorporates an upwind-biased, flux-difference-splitting approach. In addition, a newly developed capability that allows for generalized surface patching among blocks is employed. Turbulent results are presented for flow conditions that correspond to recent NASA F/A-18 High Alpha Research Vehicle flight experiments. Good correlations between the computations and the flight test results are disclosed for both surface flow patterns as well as surface pressure distributions.
Strains and displacements in a small area near a longitudinal lap joint in the fuselage skin of a B737 aircraft were measured during a pressurization cycle to a differential pressure of 6.2 psi while the aircraft was on the ground. It was found that hoop strains were higher than longitudinal strains at each location; membrane strains in the unreinforced skin were higher than in the joint; membrane strains in the hoop direction, as well as radial displacements, tended to be highest at the mid-bay location between skin reinforcements; significant bending in the hoop direction occurred in the joint and in the skin near the joint, and the bending was unsymmetrically distributed about the stringer at the middle of the joint; and radial displacements were unsymmetrically distributed across the lap joint. The interpretation of the strain gage data for locations on the bonded and riveted lap joint assumed that the joint did not contain disbonded areas.
This user's manual contains a complete description of the computer programs developed to calculate three-dimensional, compressible, laminar boundary layers for perfect gas flow on general fuselage shapes. These programs include the 3-D boundary layer program (3DBLC), the body-oriented coordinate program (BCC), and the streamline coordinate program (SCC). Subroutine description, input, output and sample case are discussed. The complete FORTRAN listings of the computer programs are given.