Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FEASIBILITY STUDIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Economic viability of using thermal energy storage for flexible carbon capture on natural gas power plants

Fossil fuel-based power plants generate 80% of the electricity in the United States and provide a reliable generation source for both base and peak power demands. These plants are expected to adapt to changes in environmental policies that will require carbon management with carbon capture and storage (CCS) representing a possible solution. Current solvent-based CCS has a detrimental impact on a power plant's performance due to large heat loads required for carbon capture solvent regeneration. This parasitic load restricts the power plant's output and operation flexibility. Therefore, this study evaluates the feasibility of using thermal storage technologies for natural gas combined cycle (NGCC) power plants coupled with CCS to minimize the impact of solvent regeneration and enable the plant to operate at peak power output. Thermal storage can minimize the impact of CCS on the power plant by providing the heat load required for solvent regeneration during times of peak demand which will allow the plant to operate unrestricted and at full power. In total, fifteen unique thermal storage configurations were evaluated from three thermal storage categories: Brayton cycle heat pump, vapor compression heat pump, and heat recovery steam generator steam extraction for storage. The viability of these systems was determined by evaluating each configuration on thousands of real-world Locational Marginal Pricing (LMP) profiles from the New York Independent System Operator and California Independent System Operator electricity markets using a techno-economic analysis. Afterwards, results were compared to the performance of a base power plant (NGCC with CCS and no thermal storage) to determine the impact of thermal storage on power plant economics. Overall, six of the thermal storage configurations performed better than base CCS enabled power plant on between 11.5% and 38.7% of the LMP signals evaluated. The best performing configuration was a vapor compression heat pump that used flue gas as the working fluid and had both hot and cold thermal storage units. This configuration performed better than the base CCS power plant on 38.7% of the LMP profiles. The results of this study show thermal storage can mitigate the economic impact of carbon capture solvent regeneration on NGCC power plants. Discussion focuses on the impact of electricity pricing on the optimal thermal storage system, the advantages and disadvantages of the systems evaluated, and identifies limitations with the study.

25 ENERGY STORAGE↗
DOE OSTI2022

Investigation of enhanced CO 2 storage in deep saline aquifers by WAG and brine extraction in the Minnelusa sandstone, Wyoming

Geological CO 2 sequestration in deep saline aquifers has been extendedly investigated to reach the goal of carbon neutral as large amount of CO 2 can be reduced in a short time. Here, this study investigates the feasibility of water-alternating-gas (WAG) injection and brine extraction on enhancing CO 2 storage in a target deep saline aquifer, Minnelusa Sandstone in the Powder River Basin (PRB) of Wyoming. An integrated numerical model is developed to account for four scenarios: (1) CO 2 continuous injection (CI) through one injection well, (2) WAG injection through one injection well, (3) CO 2 CI through one injection well and brine extraction through one producer, (4) WAG injection through one injection well and brine extraction through one producer. Simulation results suggest that WAG injection and brine extraction corporately make it possible to enhance CO 2 injectivity while securing CO 2 storage safety. For instance, WAG injection considerably reduces structural trapping contribution while enhances dissolved and residual trapping contributions. As for brine extraction, it can decrease the maximum averaged reservoir pressure by 37% and 22% for CI and WAG injection, respectively. Besides, sensitive analyses of the operational parameters for the fourth scenarios are performed. Results reveal that, when the amount of total CO 2 injection has been predetermined, CO 2 injection time and rate within each period of WAG should be small whereas it is preferable to have large water injection time and rate. This is to secure desirable dissolved and residual trapping contributions (store CO 2 with safety). Sensitive degree results confirm that CO 2 injection rate, water injection time, and CO 2 injection time of WAG injection exhibit significant effects on CO 2 storage whereas the impacts of producer bottom-hole pressure (BHP), water injection rate, and CO 2 -water injection time are relatively weaker. This study not only sheds light on achieving double-win goal: enhance CO 2 injectivity and store CO 2 with safety, but also can be a critical reference for other CO 2 storage in deep saline aquifers.

58 GEOSCIENCES↗
DOE OSTI2020

Subtask 1.3 – Integrated Carbon Capture and Storage for North Dakota Ethanol Production

The Energy & Environmental Research Center (EERC), in partnership with Red Trail Energy, LLC (RTE), a North Dakota ethanol producer; the North Dakota Industrial Commission (NDIC) Renewable Energy Program (REP); and the U.S. Department of Energy (DOE), conducted a feasibility and implementation study for a commercial carbon capture and storage (CCS) effort. This subtask provided technical support and developed recommended practices of how small-scale industrial CO2 emitters (<1,000,000 tonnes of CO2 emitted annually) may economically deploy CCS. The 64-million-gallon dry mill RTE ethanol facility, emitting an average 180,000 tonnes of CO2 annually, was the subject of the case study. The positive outcome of this research, which shows technical and economic potential for ethanol–CCS in North Dakota, has resulted in RTE acquiring an approved Permit to Drill on December 2, 2019, for a stratigraphic test well in early 2020, a necessary step toward a North Dakota CO2 Storage Facility Permit (SFP) for the RTE CCS effort. Outcomes include 1) validating the Broom Creek Formation as a regional target for CCS, 2) determining the full carbon life cycle of an industrial fuel production facility with CCS, 3) developing a field implementation plan (FIP) for small-scale CCS, and 4) determining the validity and pathway for using CCS to meet low-carbon fuel (LCF) standards. The technical team included the EERC, RTE, Trimeric Corporation, Schlumberger Carbon Services, and Computer Modelling Group (CMG). Findings from activities conducted November 2016 – May 2020 are summarized as follows. Several key steps have been accomplished toward validating the Broom Creek Formation as a CO2 injection and storage target at the RTE CCS site, including verification of the presence and structure of sandstone layers that may comprise the potential CO2 storage reservoir and the several thousand feet of overlying confining zone. Work included site characterization using existing data, interpretation of seismic data within the study area, and geologic modeling simulation of CO2 injection. Interpreted results estimate 3000 feet of confining zone between the Broom Creek Formation (storage target) and the lowermost underground source of drinking water (e.g., the Fox Hills Formation). The thickness of the Broom Creek injection target varies 230–420 ft within the survey area. Results were used to inform the location of a stratigraphic test well and associated characterization test program. No impediments were identified within the targeted CO2 storage complex that would prevent the project from moving forward. A stratigraphic test well is the next step to validate these results and to acquire remaining data necessary to develop a North Dakota CO2 SFP application. The EERC generated full carbon life cycle estimates for CCS integration with the RTE ethanol facility. Results indicated that an average 40% reduction in CO2 emissions is possible through CCS implementation. Approximately half of the carbon in the overall life cycle for a dry mill ethanol plant is generated through the fermentation process and emitted to the atmosphere; this is the CO2 stream targeted for CCS. The remaining carbon is attributed to corn feedstock farming (diesel, fertilizer), energy for fuel processing (natural gas, electricity), and transportation (diesel) of the fuel product. Life cycle carbon estimates are also affected by the anticipated energy consumption of a potential capture facility, which depend on the type of CO2 product generated. For example, a 30%–40% net CO2 emission reduction is estimated if a liquefied CO2 facility were incorporated compared to a 40%–50% net CO2 reduction if a supercritical “injection-grade” CO2 product is generated; i.e., more energy is required to further refine the CO2 stream, affecting the full carbon life cycle estimates. A CCS FIP was developed and initiated at the RTE CCS site, resulting in the development of several guidance documents: a CO2 Capture Process Design Package, a North Dakota CO2 geologic Storage Permits Template, and a Public Outreach Package for CCS in North Dakota. General FIP components include CO2 capture system, pipeline and well designs; monitoring, verification, and accounting (MVA) plans; geologic characterization and testing programs; and permitting and outreach plans. Vendor bids were also acquired for the CO2 liquefaction facility. Near-surface characterization (groundwater and soil gas sampling) and geologic characterization (seismic survey) were initiated to inform development of a UIC Class VI-compliant MVA plan compliant with a North Dakota CO2 SFP. Designs (well and geologic testing) were completed for a stratigraphic test well compliant with a North Dakota CO2 SFP. In addition, the outreach plan was executed, including community open houses, meetings with city/county/state officials, and development of public materials. Although other entities continued to mature incentive programs in 2019–2020, California and the Internal Revenue Service (IRS) currently provide the most advanced economic opportunities for CCS integrated with fuel production. The California Low-Carbon Fuel Standard (LCFS) adopted a CCS Protocol in January 2019, allowing submittal of a design-based pathway (DBP) application for an approved temporary (not certified) carbon intensity value for a fully engineered facility. An ethanol–CCS DBP application to the California LCFS Program (officially approved February 28, 2020) was developed to show that the RTE CCS effort meets LCFS requirements. The approved DBP provides confidence to advance the project and supports potential investments. Other entities continue to mature incentive programs. The IRS issued guidance in February 2020 that addresses the definition of beginning of construction and revenue procedure on partnerships for the Enhancement of Carbon Dioxide Sequestration Credit (a.k.a. Section 45Q) CCS tax credit program; the IRS anticipates issuing further guidance on issues such as secure geologic storage, utilization qualifications, and recapture of claimed credits. Maturing incentive programs coupled with workable permitting regulations provide confidence to advance CCS projects in North Dakota and support financial investment to proceed with designing, constructing, and implementing CCS projects at small-scale fuel production facilities. The largest hurdles for CCS implementation at small-scale industrial systems are often business/economic-related (i.e., not technical). Market uncertainty already exists for agriculture-based alternative fuels such as corn ethanol, for which production has increased by ~33%, and prices have correspondingly lowered since 2015. Passing the Section 45Q tax credit program improves economic feasibility for CCS but may require external investors for a small business to achieve maximum benefits. Public–private partnerships with NDIC and DOE have resulted in foundational technical and regulatory knowledge, growing stakeholder confidence, and a pathway to implementation that enables similar industrial CCS projects in the region to advance. This subtask was funded through the EERC–DOE Joint Program on Research and Development for Fossil Energy-Related Resources Cooperative Agreement No. DE-FE0024233. Nonfederal funding was provided by NDIC and RTE. The authors would also like to thank CMG, ESRI, IHS, Neuralog, and Schlumberger for allowing the use of their software packages in support of this work.

42 ENGINEERING↗
DOE OSTI2023

A High‐Rate Li–CO 2 Battery Enabled by 2D Medium‐Entropy Catalyst

Abstract Lithium‐air batteries based on CO 2 reactant (Li–CO 2 ) have recently been of interest because it has been found that reversible Li/CO 2 electrochemistry is feasible. In this study, a new medium‐entropy cathode catalyst, (NbTa) 0.5 BiS 3 , that enables the reversible electrochemistry to operate at high rates is presented. This medium entropy cathode catalyst is combined with an ionic liquid‐based electrolyte blend to give a Li–CO 2 battery that operates at high current density of 5000 mA g −1 and capacity of 5000 mAh g −1 for up to 125 cycles, far exceeding reported values in the literature for this type of battery. The higher rate performance is believed to be due to the greater stability of the multi‐element (NbTa) 0.5 BiS 3 catalyst because of its higher entropy compared to previously used catalysts with a smaller number of elements with lower entropies. Evidence for this comes from computational studies giving very low surface energies (high surface stability) for (NbTa) 0.5 BiS 3 and transmission electron microscopystudies showing the structure being retained after cycling. In addition, the calculations indicate that Nb‐terminated surface promotes Li–CO 2 electrochemistry resulting in Li 2 CO 3 and carbon formation, consistent with the products found in the cell. These results open new direction to design and develop high‐performance Li–CO 2 batteries.

25 ENERGY STORAGE↗
DOE OSTI2025

Minimizing Inter‐Lattice Strain to Stabilize Li‐Rich Cathode by Order–Disorder Control

Li-rich Mn-based layered (LMR) cathodes with anionic redox chemistry show great potential for next-generation sustainable Li-ion battery (LIB) applications due to the low cost and high energy density. However, the asynchronous structural evolutions with cycling in the heterogeneous composite structure of LMR lead to serious lattice strain and thus fast electrochemical decay, which hinders the commercialization of LMR cathodes. Here, in this study, an order–disorder coherent LMR cathode is demonstrated that exhibits a higher average voltage (by 0.25 V), negligible voltage decay (97.6% voltage retention after 100 cycles at 100 mA g −1 ), and enhanced cycling stability (98% capacity retention after 200 cycles at 100 mA g −1 ) compared to its layered oxide counterparts. It is proposed that this order–disorder coherent structure design can promote a more synchronous and homogeneous structure evolution during charge and discharge, thus minimizing lattice strain, which significantly prevents layer collapse and collective degradation at high voltage, improving the electrochemical stability. The study displays the feasibility of optimizing the performance of Li-rich cathode materials through a dedicated order–disorder structure control for sustainable energy storage.

Xu, Shenyang [Peking University, Shenzhen (China)]↗
DOE OSTI2026

Hybrid Additive Manufacturing and Electric Field-Assisted Sintering of High-temperature Heat Exchangers via Sacrificial Channel Molds

A hybrid manufacturing approach, integrating additive manufacturing (AM) with powder methodology via electric field-assisted sintering (EFAS), was developed for the fabrication of high-temperature compact heat exchangers (CHX) from refractory metals. The methodology employed additively manufactured sacrificial channel molds (SCMs) as shapeholders for CHX channels, which were embedded in metal powders using EFAS. Following embedding, the SCMs were chemically dissolved to form the internal channel network. SCMs were fabricated using both digital light processing (DLP) and direct ink writing (DIW) from chemically reactive, calcium-based ceramic feedstocks with varying ratios of Al2O3 reinforcement. The microstructure, phase composition, and dissolution behavior of both as-printed and embedded SCMs were investigated. The shrinkage behavior of the SCMs embedded in refractory metals, as well as the interfacial characteristics between the SCMs and metal matrix, were studied. The results showed that the SCMs containing sufficient chemical reactive ceramics dissolved effectively before and after embedding. The as-printed SCMs retained the phase composition of their feedstocks, but the embedded SCMs containing calcium-based ceramics and Al2O3 exhibited the formation of calcium aluminates due to high temperature exposure during embedding. Most SCMs exhibited a cellular Al2O3 network filled with Ca-rich ceramics. Shrinkage after embedding was strongly dependent on SCM density, with lower density SCMs exhibiting greater shrinkage. A thin SCM-affected zone was observed at the metal matrix surface, characterized by increased porosity compared to the bulk matrix. This effect was attributed to infiltration of the SCM materials into powder particle boundaries under pressure, followed by their removal during dissolution. This study demonstrates the feasibility of manufacturing CHXs from hard-to-process refractory metals for use in harsh environments.

36 - MATERIALS SCIENCE↗
DOE OSTI2020

A Fluorination Method for Improving Cation-Disordered Rocksalt Cathode Performance

In Li-rich cation-disordered rocksalt oxide cathodes (DRX), partial fluorine substitution in the oxygen anion sublattice can increase the capacity contribution from transition-metal (TM) redox while reducing that from the less reversible oxygen redox. To date, limited fluorination substitution has been achieved by introducing LiF precursor during the solid-state synthesis. To take full advantage of the fluorination effect, however, a higher F content is desired. In the present study, the successful use of a fluorinated polymeric precursor is reported to increase the F solubility in DRX and the incorporation of F content up to 10–12.5 at% into the rocksalt lattice of a model Li-Mn-Nb-O (LMNO) system, largely exceeding the 7.5 at% limit achieved with LiF synthesis. Higher F content in the fluorinated-DRX (F-DRX) significantly improves electrochemical performance, with a reversible discharge capacity of ≈255 mAh g –1 achieved at 10 at% of F substitution. After 30 cycles, up to a 40% increase in capacity retention is achieved through the fluorination. Overall, the study demonstrates the feasibility of using a new and effective fluorination process to synthesize advanced DRX cathode materials.

25 ENERGY STORAGE↗
DOE OSTI2021

Silicon Anodes with Improved Calendar Life Enabled By Multivalent Additives

Silicon is widely recognized as the most promising upgrade for graphite anodes due to its much higher capacity, natural abundance, and ability to be directly applied in the slurry-based, roll-to-roll production lines. However, in addition to the fast capacity decay, silicon anodes also suffer from inferior calendar life in practical applications due to the unstable solid-electrode interface (SEI). Until now, strategies to effectively improve the calendar life by tailored SEIs remain largely unclear, especially in high-Si content, zero-graphite anodes. Here, silicon anodes with superior calendar life are developed by adding small concentrations of multivalent salts into the baseline electrolyte. The Ca additive reacts with the F ions in the electrolyte, forming a layer of nanocrystalline CaF 2 that is closely coated around the silicon particles. The CaF 2 -enabled new SEI is strong and dense, which effectively protects the silicon core from side reactions, leading to lower capacity decay after calendar aging at high voltage. More importantly, the Ca additive is effective universally for all available commercial silicon or SiO sources. This study provides a feasible and low-cost solution for developing silicon anodes with long calendar life, paving the way towards commercially viable silicon anodes.

25 ENERGY STORAGE↗
DOE OSTI2022

Alternate Synthesis Method for High-Performance Manganese Rich Cation Disordered Rocksalt Cathodes

Cation-disordered rocksalt (DRX) cathodes have recently emerged as a promising class of cobalt-free, high-capacity cathodes for lithium-ion batteries. To facilitate their commercialization, the development of scalable synthesis techniques providing control over composition and morphology is critical. To this end, a sol-gel synthesis route to prepare Mn-rich DRX cathodes with high capacities is presented here. Several compositions with varied Mn content and nominal F doping are successfully prepared using this technique. In-situ X-ray diffraction measurements demonstrate that DRX formation proceeds at moderate temperature (800 °C) through the sol-gel route, which enables intimate mixing among reactive intermediate phases that form at lower temperatures. All synthesized compositions possess cation short-range order, as evidenced by neutron pair distribution function and electron diffraction analysis. These DRX materials demonstrate promising electrochemical performance with reversible capacities up to 275 mAh g. Compared to the baseline oxide (Li 1.2 Mn 0.4 Ti 0.4 O 2 ), the Mn-rich compositions exhibit improved cycling stability, with some showing an increase in capacity upon cycling. Finally, this study demonstrates the feasibility of preparing high-capacity DRX cathodes through a sol-gel based synthesis route, which may be further optimized to provide better control over the product morphology compared to traditional synthesis methods.

25 ENERGY STORAGE↗
DOE OSTI2024

Epitaxial Thin Film Growth on Recycled SrTiO 3 Substrates Toward Sustainable Processing of Complex Oxides

Complex oxide thin films cover a range of physical properties and multifunctionalities that are critical for logic, memory, and optical devices. Typically, the high‐quality epitaxial growth of these complex oxide thin films requires single crystalline oxide substrates such as SrTiO 3 (STO), MgO, LaAlO 3 , a‐Al 2 O 3, and many others. Recent successes in transferring these complex oxides as free‐standing films not only offer great opportunities in integrating complex oxides on other devices, but also present enormous opportunities in recycling the deposited substrates after transfer for cost‐effective and sustainable processing of complex oxide thin films. In this work, the surface modification effects introduced on the recycled STO are investigated, and their impacts on the microstructure and properties of subsequently grown epitaxial oxide thin films are assessed and compared with those grown on the pristine substrates. Detailed analyses using high‐resolution scanning transmission electron microscopy and geometric phase analysis demonstrate distinct strain states on the surfaces of the recycled STO versus the pristine substrates, suggesting a pre‐strain state in the recycled STO substrates due to the previous deposition layer. These findings offer opportunities in growing highly mismatched oxide films on the recycled STO substrates with enhanced physical properties. Specifically, yttrium iron garnet (Y 3 Fe 5 O 12 ) films grown on recycled STO present different ferromagnetic responses compared to that on the pristine substrates, underscoring the effects of surface modification. The study demonstrates the feasibility of reuse and redeposition using recycled substrates. Via careful handling and preparation, high‐quality epitaxial thin films can be grown on recycled substrates with comparable or even better structural and physical properties toward sustainable process of complex oxide devices.

pre-strained STO surfaces↗
DOE OSTI2023

Inferring colloidal interaction from scattering by machine learning

A machine learning solution for the potential inversion problem in elastic scattering is outlined. The inversion scheme consists of two major components, a generative network featuring a variational autoencoder which extracts the targeted static two-point correlation functions from experimentally measured scattering cross sections, and a Gaussian process framework which probabilistically infers the relevant structural parameters from the inverted correlation functions. Via a case study of charged colloidal suspensions, the feasibility of this approach for quantitative study of molecular interaction is critically benchmarked and its merit over existing deterministic approaches, in terms of numerical accuracy and computationally efficiency, is demonstrated.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Electrochemically-assisted removal of cadmium ions by redox active Cu-based metal-organic framework

An electrochemically-assisted wastewater treatment using Faradaic materials offers a promising technique for the selective removal of hazardous substances. Here, we demonstrate the reversible capture and release of cadmium ions in aqueous solutions, using a redox-active metal-organic framework (MOF) electrode. As-synthesized copper-based MOF (Cu-MOF-74; copper 2,5-dihydroxyterephthalate) is a highly attractive candidate for Faradaic electrosorption due to its large surface area, water stability, and redox-active metal nodes. Our work demonstrates the reversible capture and release of Cd 2+ ions assisted by the electrochemical redox reaction of Cu 2+ /Cu + within the MOF structure. Combined material characterization and electrosorption tests were carried out to determine the operational conditions for maximizing adsorption capacity, energy efficiency, and material stability, thus leading to excellent electrosorption (>100 mg g -1 ) and regeneration efficiency (>90%). This study demonstrates the feasibility of leveraging MOFs containing redox-active metal nodes for the selective separation of toxic cations, and paves the way for promising future applications of these 3-D porous structures for wastewater treatment and environmental remediation.

42 ENGINEERING↗
DOE OSTI2025

De-Risking High-Recovery Brackish Water Desalination via Flow Reversal and Feed Flushing Using Techno-Economic Assessment

Novel desalination technologies have demonstrated enhanced performance and improved financial metrics over existing processes adopted by industry. Establishing quantitative performance targets is essential for achieving financial benefits over the current state of the art. Herein, we demonstrate how WaterTAP, a techno-economic assessment (TEA) tool, can be used to identify minimum performance metrics necessary to achieve financial benefit over using existing processes. This study evaluates the feasibility of increasing water recovery at the Chino Desalter I above 90 % through the addition of a third variable configuration reverse osmosis (VCRO) stage. Sensitivity analyses revealed flow reversal frequency, feed flushing volume (used as a cleaning step), and membrane lifespan are key factors influencing the financial viability of the VCRO process. The TEA analysis demonstrated that the system must achieve a recovery of 84 % and a 1-year membrane lifespan to have a breakeven LCOW, while achieving 90 % recovery can ultimately reduce the LCOW by 16 %. Notably, a trade-off between decreasing frictional losses and increased osmotic pressure across the recovery range, resulted in a stable specific energy consumption across the recovery range, enabling meaningful LCOW reductions without an energy penalty, a key finding that contrasts with conventional RO. This work demonstrates how TEA can guide system design by identifying key performance targets and exploring trade-offs, enabling data-driven decisions to de-risk innovative processes. These findings underscore the importance of leveraging TEA to evaluate scaling mitigation strategies and optimize inland desalination systems for sustainable and cost-effective operation.

14 SOLAR ENERGY↗
DOE OSTI2022

Sensor cost-effectiveness analysis for data-driven fault detection and diagnostics in commercial buildings

Data-driven building fault detection and diagnostics (FDD) is heavily dependent on sensors. However, common sensors from Building Automation Systems are not optimized to maximize accuracy in FDD. Installing additional sensors that provide more detailed building system information is key to maximizing the performance of FDD solutions. Here in this paper, we present a sensor cost analysis workflow to quantify the economic implications of installing new sensors for FDD using the concept of sensor threshold marginal cost (STMC). STMC does not represent actual sensor cost. Rather, it represents a target cost based on the economic benefit that would be realized through improved FDD performance and one or more specified economic criteria. We calculate STMCs for multiple possible fault types and use fault prevalence information to aggregate STMCs into a single dollar value to determine the cost-effectiveness of a potential sensor investment. We conducted a case study using Oak Ridge National Laboratory's Flexible Research Platform (FRP) test facility as a reference. The case study demonstrates the feasibility of the analysis and highlights the key cost considerations in sensor selection for FDD. The results also indicate that identifying and installing the few key sensor(s) is critical to cost-effectively improve FDD performance.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2022

Utilizing lowly-reactive coal gasification fly ash (CGFA) to stabilize aggregate bases

This study explored the feasibility of utilizing lowly-reactive coal gasification fly ash (CGFA) for stabilizing road aggregate bases. Three types of aggregate stabilizers including the ordinary Portland cement (OPC)-CGFA, hydrated lime (CH)-CGFA and alkali-activated CH-CGFA were evaluated based on the performances of compacted base specimens. It was found that the OPC-CGFA stabilized bases showed better mechanical and durability properties while the CH-CGFA samples had low water stability and freeze-thaw durability due to the dissolution of unreacted CH. However, the reaction degree of CGFA associated with the performances of CH-CGFA stabilization could be considerably enhanced by the alkali-activation. The sustainability and economic feasibility analyses showed the use of CGFA could significantly reduce the CO 2 emissions and costs, highlighting the synergy between the recycling of CGFA and the construction of sustainable road bases. Here, a framework of selecting CGFA-based stabilizers for road bases was proposed considering the performance ratings of the material properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Radiation-induced dry reforming: A negative emission process

The reaction between the most abundant greenhouse gases (GHG) to produce hydrogen might represent the most powerful and effective decarbonizing opportunity, if a low-carbon energy source is used to drive it. This is the case of methane (CH 4 ) dry reforming (MDR) where its reaction with carbon dioxide (CO 2 ) produces synthesis gas (syngas, a mixture of carbon monoxide and hydrogen). Here this study explores the feasibility of using ionizing radiation to induce the MDR reaction, at low temperatures and/or less energy demanding conditions. Additionally, the ionizing radiation is proposed to be supplied by nuclear power plants (NPPs), which are low-carbon reliable energy generation sources. Thus, the radiolysis of CO 2 , CH 4 and their mixtures, under ?-irradiation was evaluated in the absence and presence of nickel catalysts. The radiation-induced MDR reaction and radiation-induced catalytic promotion were proven to take place at temperatures close to ambient though at low conversion, with yields below 1%. Since irradiation and heat can be provided by a nuclear power plant, this radiation-induced reaction establishes a connection between nuclear energy to renewable resources and enables a pathway for a decarbonized cleaner chemical industry, for producing green chemicals.

08 HYDROGEN↗
DOE OSTI2021

A novel solid oxide electrolytic cell with reduced endothermic load for CO 2 electrolysis using (La 0.80 Sr 0.20 ) 0.95 MnO 3-δ cathode

CO 2 conversion to CO via solid oxide electrolysis provides a potentially efficient method for converting CO 2 into an industrially relevant product. A solid oxide electrolysis cell with (La 0.80 Sr 0.20 ) 0.95 MnO 3-δ (LSM) as the CO 2 reduction cathode, yttrium stabilized zirconia (YSZ) as electrolyte, and nickel as the H 2 oxidation anode was operated 800 °C and 850 °C. Thermogravimetric analysis of the LSM material showed no catalyst oxidation at operating temperatures allowing for CO 2 electrolysis without reducing safe gas. In addition, no cathode material mass gain was observed in the presence of CO suggesting little to no carbon deposition occurred above 750 °C. The formation rates of CO for the cell reached 1.15 mL∙min-1∙ cm -2 for an applied current of 150 mA∙cm -2 achieving a faradaic efficiency of 100 %. Furthermore, the cell displayed good stability in the short-term CO 2 electrolysis test with a nominal voltage drop of 4 mV h -1 for 10 h at 850°C. This study shows the feasibility of operating a solid oxide CO 2 electrolysis cell for CO production with H 2 at the anode to reduce endothermic process load.

(La0.80Sr0.20)0.95MnO3-δ↗
DOE OSTI2020

Characterization of flow and transport in a fracture network at the EGS Collab field experiment through stochastic modeling of tracer recovery

Energy extraction from subsurface reservoirs is important for addressing the increasing energy demand and environmental concerns such as global warming. However, the characterization of subsurface reservoirs, particularly reservoirs dominated by fracture networks remains a challenge due to the lack of means to directly observe subsurface processes. This study explores the feasibility and efficacy of characterizing fracture flow and transport processes in an enhanced geothermal system (EGS) testbed through stochastic tracer modeling. There are two enabling factors that allow application of stochastic modeling to characterize a subsurface reservoir. First, an abundance of geological and geophysical measurements enables the development of a high-fidelity and well-constrained fracture network model. Second, high-performance computing (HPC) allows running massive realizations efficiently. Six conservative tracer tests were stochastically modeled and produced satisfactory realizations that successfully reproduce field tracer recovery data from each tracer test. The evolution of flow and transport processes in the fracture network was then analyzed from these satisfactory realizations. This work demonstrates that stochastic tracer modeling on a high-fidelity fracture network model is feasible and can provide important insights regarding flow and transport characteristics in subsurface fractured reservoirs.

58 GEOSCIENCES↗