SEARCH · Engineering Papers
Results for “Extrusion Process”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Corrosion Behavior of AZ31 Magnesium Alloy Produced by Continuous Variable Cross Section Direct Extrusion
In order to study the corrosion behavior of magnesium alloys of high performance in the simulated seawater by continuous variable cross section direct extrusion (CVCDE), an electrochemical method and weight loss method were used to study the difference between AZ31 magnesium alloys produced by CVCDE with different numbers of interim dies to examine the electrochemical corrosion behavior and corrosion rate at 3.5 wt.% NaCl solution in this paper. Scanning electron microscopy and x-ray diffraction were used to analyze the morphology of corrosion surfaces and the composition of the corrosion products of samples soaked for different times. The results show that after CVCDE with different numbers of interim dies, the size of the microstructure is refined gradually, and the grain orientation is also different; with the increase in the number of interim dies, the thermodynamic corrosion tendencies are different, and the corrosion resistance of samples extruded by conventional extrusion is relatively good; the charge transfer and material transfer process are the two main factors affecting the corrosion rate, which determines the direction of the electrochemical reaction; the corrosion form of the sample extruded by CVCDE is the local corrosion which is the filiform corrosion and pitting corrosion, and the corrosion product is mainly water-insoluble Mg(OH){sub 2}.
Processing and Properties of CNTs/ADC12 Nanocomposite
Carbon nanotubes (CNTs)-reinforced ADC12 nanocomposite was successfully fabricated via casting. The CNTs-Al master alloy was prepared by hot extrusion, and the CNTs were dispersed into the matrix by a high-intensity ultrasonic treatment during the casting process to yield 0.5, 1.0, 1.5 wt.% of the CNTs/ADC12 composite. The key step in arriving at homogeneous distribution of CNTs was preparation of the CNTs-Al master alloy and the introduction of a high-intensity ultrasonic treatment method. The cavitation bubbles that adhered to the aggregated CNTs closed rapidly and released large amounts of energy, which had an impact via the cavitation effect, which made the aggregated CNTs dissociate and disperse homogeneously into the melt. Under the conditions of ultrasonic power of 2.1 kW and ultrasonic time of 10 min, the mean diameter of α-Al was 53.2 μm, which was 58.9% lower than that of the matrix. The microhardness and the ultimate tensile strength (UTS) of nanocomposite with 1.0 wt.% CNTs addition increased by 29.3 and 27%, respectively, as compared with the matrix. CNTs can be dispersed in the matrix homogeneously. It was observed by scanning electron microscope (SEM) that CNTs as a load-bearing element were embedded in the matrix independently, enhancing the mechanical properties. This suggested that the improvement of mechanical properties could be attributed to the size and degree of CNTs clustering, the load transfer from the matrix to the CNTs and the grain refinement of the nanocomposite.
Achieving strength-ductility synergy in hierarchical aluminum metal matrix composites via friction extrusion
We report the fabrication of aluminum metal matrix composites (Al-MMCs) with hierarchical architectures via friction extrusion (FE), a scalable, single-step, solid-phase processing technique. Precursor pucks containing 0–15 vol% Al₂O₃ particles were extruded into fully dense AA6061-based composite rods. The FE induced a tree-ring-like architecture of concentric particle-rich and particle-lean bands, yielding refined grains in particle-rich regions and coarser grains elsewhere. At the nanoscale, magnesium in AA6061 selectively reacted with Al₂O₃ particles to form virus-like nodes, improving particle–matrix bonding. This multi-scale design strategy, combining mesoscale architecture, microscale grain refinement, and nanoscale interface engineering overcome the conventional strength–ductility trade-off. Tensile testing showed substantial increases in yield and ultimate tensile strengths while retaining high ductility ( > 20%). Enhanced strain hardening, driven by the accumulation of geometrically necessary dislocations at interfaces, contributed to the performance. The hierarchical microstructure produced by FE demonstrates a promising pathway for scalable fabrication of lightweight MMCs for structural applications requiring a combined high strength and ductility.
Analysis on Part Distortion and Residual Stress in Big Area Additive Manufacturing with Carbon Fiber-Reinforced Thermoplastic using Dehomogenization Technique
Part distortion and bottom surface warpage often occur in extrusion-based additive manufacturing. The undesirable deformations during the printing process are due to residual stresses caused by material shrinkage. Analysis on residual stress and deformation requires accurate thermo-mechanical material properties. Polymer composites reinforced with short fibers have intrinsic inhomogeneities with nonuniform fiber orientation. Therefore, homogenized macro properties may not accurately represent the progressive damage behavior or distortion. In this study, fiber orientations in Acrylonitrile Butadiene Styrene (ABS) reinforced with 20%wt carbon fiber are calculated using a de-homogenization technique. Thermal expansion coefficients in multiple directions are obtained from Thermo-Mechanical Analysis (TMA) tests. Temperature dependent stiffness is measured, and temperature dependent strength is estimated. Thermal conductivities in multiple directions and thermal capacity are measured. The calibrated thermo-mechanical properties of the composite with de-homogenized technique are used to analyze the residual stress and distortion of a 4 ft-wide wall printed in the Big Area Additive Manufacturing (BAAM) system. For experimental measurement on the wall printing, Infra-Red (IR) camera captures the temperature field, and Linear Variable Differential Transformer (LVDT) is installed to measure the warpage at the bottom surface. The experimental data are compared to the numerical analysis results. The temperature profile and the distortion profile from experiment are close to the simulation results. Damages due to residual stress and distortion are analyzed.
Slow wave structures using twisted waveguides for charged particle applications
A rapidly twisted electromagnetic accelerating structure includes a waveguide body having a central axis, one or more helical channels defined by the body and disposed around a substantially linear central axial channel, with central portions of the helical channels merging with the linear central axial channel. The structure propagates electromagnetic waves in the helical channels which support particle beam acceleration in the central axial channel at a phase velocity equal to or slower than the speed of light in free space. Since there is no variation in the shape of the transversal cross-section along the axis of the structure, inexpensive mechanical fabrication processes can be used to form the structure, such as extrusion, casting or injection molding. Also, because the field and frequency of the resonant mode depend on the whole structure rather than on dimensional tolerances of individual cells, no tuning of individual cells is needed. Accordingly, the overall operating frequency may be varied with a tuning/phase shifting device located outside the resonant waveguide structure.
THE IMPACT OF A STATIC-MIXING NOZZLE ON UNIFORMITY IN MATERIAL EXTRUSION LARGE-SCALE ADDITIVE MANUFACTURING
There are many methods of incorporating more than one material in Additive Manufacturing (AM) processes. Oak Ridge National Laboratory has developed a unique solution that enables in-situ material switching by developing a dual-hopper feed system for Cincinnati’s Big Area Additive Manufacturing (BAAM) system. Continuous extrusion during a step-change in material feedstock results in a unique blended material transition region that exhibits a heterogeneous internal morphology. To improve mixing of materials during extrusion, a customized static-mixing nozzle was created for use with the BAAM. Single-bead transitions from Material A to B and B to A were printed with the mixing nozzle at a specified screw speed. Compositional analysis tracked the progression of the material transition as a function of extrudate volume. The resulting transition curves were compared against a standard nozzle configuration. Optical microscopy of cross sections also demonstrated that the static-mixing nozzle promoted a more uniform bead geometry as well as a more homogeneous internal structure throughout the material transition.
Neutron Irradiation of Nuclear Structural Materials Fabricated by Powder Metallurgy with Hot Isostatic Pressing
An irradiation campaign intended to produce data necessary to qualify various reactor structural materials fabricated by powder metallurgy with hot isostatic pressing (PM/HIP) is currently in progress. Manufacturing processes have considerable influence over the safety and integrity of nuclear reactor vessels and internal components. Established processes such as casting, plate rolling and welding, forging, drawing, and extrusion have been used to fabricate structural and pressure-retaining materials used in the nuclear power industry for the past 60 years. However, weldability and inspectability are ongoing issues in the manufacture of reactor vessels and internals. Furthermore, these components are subject to harsh service environments, which combine high radiation fluence, high temperature, and mechanical stress. These conditions can accelerate material degradation and failure, with the most extreme degradation often occurring at weldments and in poorly manufactured or inspected components. Advanced reactor designs and lifetime extensions to the existing fleet of light-water reactors (LWRs) will exacerbate materials degradation issues by increasing the duty on reactor internals. Thus, developing reliable manufacturing processes wherein high-quality weldments and inspections can be performed is of great importance to the continued safety and operation of nuclear power plants.
Structural Evolution of Layered Manganese Oxysulfides during Reversible Electrochemical Lithium Insertion and Copper Extrusion
The electrochemical lithiation and delithiation of the layered oxysulfide Sr 2 MnO 2 Cu 4-δ S 3 has been investigated by using a combination of in situ powder X-ray diffraction and ex situ neutron powder diffraction, X-ray absorption and 7 Li NMR spectroscopy, together with a range of electrochemical experiments. Sr 2 MnO 2 Cu 4-δ S 3 consists of [Sr 2 MnO 2 ] perovskite-type cationic layers alternating with highly defective antifluorite-type [Cu 4-δ S 3 ] (δ ≈ 0.5) anionic layers. It undergoes a combined displacement/intercalation (CDI) mechanism on reaction with Li, where the inserted Li replaces Cu, forming Li 4 S 3 slabs and Cu + is reduced and extruded as metallic particles. For the initial 2-3% of the first discharge process, the vacant sites in the sulfide layer are filled by Li; Cu extrusion then accompanies further insertion of Li. Mn 2.5+ is reduced to Mn 2+ during the first half of the discharge. The overall charging process involves the removal of Li and re-insertion of Cu into the sulfide layers with re-oxidation of Mn 2+ to Mn 2.5+ . However, due to the different diffusivities of Li and Cu, the processes operating on charge are quite different from those operating during the first discharge: charging to 2.75 V results in the removal of most of the Li, little reinsertion of Cu, and good capacity retention. A charge to 3.75 V is required to fully reinsert Cu, which results in significant changes to the sulfide sublattice during the following discharge and poor capacity retention. This detailed structure-property investigation will promote the design of new functional electrodes with improved device performance.
Properties of the thermally stable Al{sub 95}Cr{sub 3.1}Fe{sub 1.1}Ti{sub 0.8} alloy prepared by cold-compression at ultra-high pressure and by hot-extrusion
An Al{sub 95}Cr{sub 3.1}Fe{sub 1.1}Ti{sub 0.8} (in at.%) alloy was made into rapidly solidified powder by melt atomization. The powder was compacted by two processes: 1) uni-axial cold compression at an ultra-high pressure of 6 GPa and 2) hot extrusion at 480 Degree-Sign C. The structures, mechanical properties and thermal stability of both materials were compared with the commercial AlSi{sub 12}Cu{sub 1}Mg{sub 1}Ni{sub 1} (in wt.%) casting alloy, which is generally considered to be thermally stable. It was found that cold compression at ultra-high pressure created a compact and porosity-free material, which was similar to the material that was prepared with the commonly used hot extrusion method. The Vickers hardness, compressive strength and compressive yield strength of the cold-compressed alloy were 161 HV, 680 MPa and 547 MPa, respectively, which were higher than the values obtained for the hot-extruded and casting alloys. The thermal stability of the hot-extruded Al{sub 95}Cr{sub 3.1}Fe{sub 1.1}Ti{sub 0.8} alloy was excellent because its mechanical properties did not change significantly, even after 100 h of annealing at 500 Degree-Sign C. The mechanical properties and thermal stability of the investigated materials were discussed in relation to their structures and diffusivities of the alloying elements. - Highlights: Black-Right-Pointing-Pointer The Al{sub 95}Cr{sub 3.1}Fe{sub 1.1}Ti{sub 0.8} alloy was prepared by compression at an ultra-high pressure of 6 GPa. Black-Right-Pointing-Pointer The resulting material was dense and porosity-free. Black-Right-Pointing-Pointer The material had high hardness of 161 HV and a compressive strength of 680 MPa. Black-Right-Pointing-Pointer The material had excellent thermal stability at 500 Degree-Sign C.
Determining the Force Exerted by a Stepped Punch
The relative pressure in the cold extrusion of hollow cylindrical aluminum- and copper-alloy parts by a stepped punch is determined experimentally. A mathematical model of the process is derived.
CRADA No. NFE-10-02715 Assessment of AFA Stainless Steels for Tube Products in Chemical Processing and Energy Production Applications
Oak Ridge National Laboratory (ORNL) and Carpenter Technology Corporation (Carpenter) participated in an in-kind cost share cooperative research and development agreement (CRADA) effort under the auspices of the Energy Efficiency and Renewable Energy (EERE) Technology Maturation Program to assess material properties of several potential AFA family grades and explore the feasibility of producing alumina-forming austenitic (AFA) stainless steels in tubular form needed for many power generation and chemical process applications. Carpenter's Research Laboratory successfully vacuum melted 30 lb heats of seven candidate AFA alloy compositions representing a wide range of alloy content and intended application temperatures. These compositions were evaluated by ORNL and Carpenter R&D for microstructure, tensile properties, creep properties, and oxidation resistance. In parallel, additional work was directed toward an initial tube manufacture demonstration of a baseline AFA alloy. Carpenter successfully manufactured a 10,000 lb production heat and delivered appropriate billets to a partner for extrusion evaluation. Tube product was successfully manufactured from the baseline AFA alloy, indicating good potential for commercially produced AFA tubular form material.
Correlating processing variables to material properties in recycled polypropylene: A data‐driven approach
Abstract Polypropylene (PP) is one of the most widely used plastics, yet its recycling remains limited, with less than 1% of solid waste PP being reprocessed. Mechanical recycling through extrusion is the most practical method, but inconsistent reprocessing conditions introduce variability in material properties. While temperature, screw speed, and residence time influence the thermomechanical stress applied during reprocessing, there are no standardized guidelines for optimizing these parameters. This study examines how these factors shape the properties of recycled PP, using conditions designed to mimic post‐industrial recycled (PIR) scrap. Residence time was measured using colorimetric tracking and correlated with molecular weight, viscosity, and mechanical properties over multiple extrusion cycles. Data‐driven modeling, including response surface methodology, support vector machines, and artificial neural networks, identified processing temperature as the dominant factor in material degradation, followed by residence time. Mechanical properties remained stable, while viscosity decreased predictably with increasing residence time. By linking reprocessing conditions to property evolution, this study provides a method to optimize processing parameters and reduce variability in recycled PP. These findings help manufacturers improve process control, making recycled PP more predictable for reuse in manufacturing. Highlights Study of PIR‐quality PP without additives or compatibilizers. Residence time analysis shows processing temperature drives PP property changes. Mark‐Houwink enables quick molecular weight checks for quality control. Models predict mechanical and rheological shifts in reprocessing. Optimized processing parameters minimize property degradation in recycling.
Morphology-Controlled Discharge Profile and Reversible Cu Extrusion and Dissolution in Biomimetic CuS
Metal sulfides, such as CuS, SnS2, Co9S8, MoS2, are high capacity anode materials for Li-ion batteries. However, these materials go through a conversion reaction with Li+, which is accompanied by the phase transformation and inevitably results in a huge volume expansions, therefore causing performance degradation. Here, we report nanoscale engineering route to efficiently control the overall volume expansion for enhanced performance. We engineered CuS with nanoplate assembly on a nanostring, leading to a nanostructure of mimicking the crassula baby necklace (CBN) in the natural plant. Using in-situ transmission electron microscopy (in-situ TEM), we probed the lithiation kinetics and dynamic structural transformations. Due to the linkage of the central nanostring, the CuS CBN exhibited fast Li+ diffusion along the axial direction and high mechanical stability during lithiation. The volume expansion was minimal for the CuS CBN due to the pre-engineered gap between these plates. The CuS followed a two-step lithiation process with Cu2S and Li2S formation as the first step and Cu extrusion from Cu2S in the later stage. Interestingly, during the Cu2S to Cu conversion, there was a incubation period before the metallic Cu extrusion, which is featured by the formation of an amorphous structure due to the large lattice strain and distortion associated with the displacement of Cu by Li ions. In the final stage, the lithiated amorphous phase recrystallized to a composite of Cu nanocrystals dispersed in a polycrystalline Li2S matrix. Associate with the nanoscale size, the Cu nanocrystals can reversibly dissolve into the matrix upon delithiation. The present work demonstrates tailoring of desired functionality through nanoscale engineering of using bionic methods.
Improved High-Temperature Aluminum Alloys Containing Cerium
A common rare earth (cerium) when added to aluminum in compositions up to the eutectic compositions of around 10 wt.% improves the high-temperature performance of aluminum alloys. In the early 1980s, some promising research and development efforts focused on powder metallurgy revealed that aluminum alloys containing 4 wt.% cerium exhibit high-temperature mechanical properties exceeding those of the best commercial aluminum casting alloys then in production. Those compositions, which also included high levels of iron, were difficult to process. Recently, magnesium replaces iron to reduce density and improve processing. Cerium oxide is an abundant rare earth oxide that is often discarded during the refining of more valuable rare earths such as Nd and Dy. Therefore, the economics are compelling for cerium as an alloy additive. In this review, we report results obtained during an investigation of the processing and properties of aluminum-cerium alloys produced via casting, extrusion and additive manufacturing. The results show mechanical properties are retained at higher temperatures than other aluminum alloys and show complete recovery of mechanical properties at room temperature when exposed to elevated temperatures as high as 500 °C for 1000 h. Alloys containing cerium also have superior corrosion properties when compared to most aluminum alloys.
High-density SSiC 3D-printed Lattices for Compact HTHP Aero-engine Recuperators
The proposed project utilizes advanced ceramic-based 3D-printing technology to develop light, low-cost, ultra-compact, high-temperature high-pressure (HTHP) heat exchangers (HX) for the harsh oxidizing environment of aircraft gas-turbine engines. Typical 3D printing technologies (powder bed or lithographic techniques) cannot produce large high-density, monolithic ceramic material with intricate internal features and channels required for high-temperature, high-pressure recuperators. Furthermore, typical 3D printing technologies are not yet economical for large high-density components. A high-density material is required for hermeticity, high-temperature strength, and oxidation, corrosion, and wear resistance. The team has invented an extrusion-based additive manufacturing technology (referred to as robocasting) and developed processing techniques to tailor composition and rheological mix properties for rapid 3D printing of high-density alumina and SiC parts. The goal of the proposed project is to use robocasting technology to demonstrate commercializable high-density 3D-printed ceramic HX modules with high durability and quality, thereby reducing the risk of thermo-mechanical failure under extreme environments. In addition, the proposed project improves the quality of the ceramic 3D-printing process over a large printed area and HTHP operating conditions. Ceramic 3D printing technology also provides a means to create advanced topologies that are unobtainable with conventional manufacturing.
Enhanced Hot Tensile Ductility of Mg-3Al-1Zn Alloy Thin-Walled Tubes Processed Via a Combined Severe Plastic Deformation
In the current study, combined parallel tubular channel angular pressing (PTCAP) and tube backward extrusion (TBE), as a recently developed severe plastic deformation (SPD) method, were applied at 300 °C on a commercial Mg-3Al-1Zn alloy tubes to achieve an ultrafine grained structure. Then, the microstructure, hardness, tensile properties, and fractography evaluations were done at room temperature on the SPD-processed samples. Also, to study the hot tensile ductility of the SPD-processed samples, tensile testing was performed at an elevated temperature of 400 °C, and then, the fractured surface of the tensile samples was studied. It was observed that a bimodal microstructure, with large gains surrounded by many tiny ones, was created in the sample processed by PTCAP followed by TBE. This microstructure led to reach higher hardness and higher strength at room temperature and also led to reach very high elongation to failure (~ 181%) at 400 °C. Also, the value of elongation to failure for this sample was ~ 14.1% at room temperature. The fractographic SEM images showed the occurrence of predominately ductile fracture in the samples pulled at 400 °C. This was mostly due to the nucleation of microvoids and their subsequent growth and coalescence with each other.
Hot-melt extrudability of amorphous solid dispersions of flubendazole-copovidone: An exploratory study of the effect of drug loading and the balance of adjuvants on extrudability and dissolution
The FDA-approved anthelmintic flubendazole has shown potential to be repositioned to treat cancer and dry macular degeneration; however, its poor water solubility limits its use. Amorphous solid dispersions may overcome this challenge, but the balance of excipients may impact the preparation method and drug release. Here, we evaluate the influence of adjuvants and drug loading on the development of an amorphous solid dispersion of flubendazole-copovidone by hot-melt extrusion. The drug, copovidone, and adjuvants (magnesium stearate and hydroxypropyl cellulose) mixtures were statistically designed, and the process was performed in a twin-screw extruder. The study showed that flubendazole and copovidone mixtures were highly extrudable, except when drug loading was high (>40%). Furthermore, magnesium stearate positively impacted the extrusion and was more effective than hydroxypropyl cellulose. The extruded materials were evaluated by modulated differential scanning calorimetry and X-ray powder diffraction, obtaining positive amorphization and physical stability results. Pair distribution function analysis indicated the presence of drug rich domains with medium-range order structure and no evidence of polymer-drug interaction. All extrudates presented faster dissolution (HCl, pH 1.2) than pure flubendazole, and both adjuvants had a notable influence on the dissolution rate. In conclusion, hot-melt extrusion may be a viable option to obtain stable flubendazole: copovidone amorphous dispersions.