Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Effective properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Effective constitutive relations for large repetitive frame-like structures

Effective mechanical properties for large repetitive framelike structures are derived using combinations of strength of material and orthogonal transformation techniques. Symmetry considerations are used in order to identify independent property constants. The actual values of these constants are constructed according to a building block format which is carried out in the three consecutive steps: (1) all basic planar lattices are identified; (2) effective continuum properties are derived for each of these planar basic grids using matrix structural analysis methods; and (3) orthogonal transformations are used to determine the contribution of each basic set to the overall effective continuum properties of the structure.

Nayfeh, A. H.↗
NASA NTRS1989

The effect of hydrogen on mechanical properties of oxygen-strengthened titanium

The effect of oxygen on the hydrogen embrittlement in titanium was investigated in two Ti-based alloys containing different amounts of oxygen: 0.064 and 0.154, in wt pct. Tensile, impact, and hardness tests were performed with and without prior hydrogenation of the specimens. Results show that, while the presence of hydrogen, even in relatively small amounts, will not affect the hardness or room-temperature tensile properties determined at relatively slow strain rates, hydrogen will reduce significantly the impact resistance, as determined by the Charpy V-notch test. This deleterious effect on the impact resistance was found to be exacerbated by an increase of oxygen in the alloy.

Wasz, M. L.↗
DOE OSTI2022

Review of the Effects of Polymer Binder Properties on Microstructure and Irreversible Volume Growth of Plastic Bonded Explosives Formulations

The rational design of effective polymeric binders for the formulation of plastic-bonded explosives (PBX) is challenging due to their inherent compositional complexity. The composites comprise irregularly shaped energetic material (EM) powders coated with low weight fractions of polymer via non-equilibrium processes such as slurry coating. Defects can deleteriously affect PBX stability and performance: nano- to micrometer-scale voids can act as loci for hot spots, lowering deflagration and detonation temperatures in unpredictable ways. Furthermore, some nominally desirable polymer properties are at odds with each other: e. g. good flow characteristics are desirable for coating and adhesion, but mechanical stiffness is needed to prevent deformation and cracking of PBX under mechanical stress. Good binder adhesion is critical, but the best means to predict and measure adhesion in PBX is not obvious. Experimental methods of determining binder adhesion on model surfaces may not capture polymer structural configurations relevant to deposition during coating. Molecular dynamics-based computational models have predicted key observables in PBX formulation, suggesting that they may be powerful tools for binder selection. In this review, primarily recent (~2006 and later) literature on polymeric binders for insensitive HE (IHE) is surveyed. We focus on how binder properties influence observable PBX properties as resistance to irreversible volume growth and void formation in PBX formulations mainly (but not exclusively) featuring 1,3,5-triamino-2,4,6-trinitrobenzene (TATB) as the EM (e. g. PBX 9502, LX-17 and others). Conclusions from these studies yield useful guidelines for choosing HE binder candidates, as well as for the general design of highly-filled polymer composite materials. Finally, studies describing challenges in PBX formulation with the newer and more energetically dense high explosive, LLM-105, will be discussed.

adhesion↗
NASA NTRS2003

The Effect of Chemical Functionalization on Mechanical Properties of Nanotube/Polymer Composites

The effects of the chemical functionalization of a carbon nanotube embedded in a nanotube/polyethylene composite on the bulk elastic properties are presented. Constitutive equations are established for both functionalized and non-functionalized nanotube composites systems by using an equivalent-continuum modeling technique. The elastic properties of both composites systems are predicted for various nanotube lengths, volume fractions, and orientations. The results indicate that for the specific composite material considered in this study, most of the elastic stiffness constants of the functionalized composite are either less than or equal to those of the non-functionalized composite.

Odegard, G. M.↗
NASA NTRS2019

Spatial Distribution of Aerosol Microphysical and Optical Properties and Direct Radiative Effect from the China Aerosol Remote Sensing Network

Multi-year observations of aerosol microphysical and optical properties, obtained through ground-based remote sensing at 50 China Aerosol Remote Sensing Network (CARSNET) sites, were used to characterize the aerosol climatology for representative remote, rural, and urban areas over China to assess effects on climate. The annual mean effective radii for total particles (ReffT) decreased from north to south and from rural to urban sites, and high total particle volumes were found at the urban sites. The aerosol optical depth at 440 nm (AOD440 nm) increased from remote and rural sites (0.12) to urban sites (0.79), and the extinction Ångström exponent (EAE440–870 nm) increased from 0.71 at the arid and semi-arid sites to 1.15 at the urban sites, presumably due to anthropogenic emissions. Single-scattering albedo (SSA440 nm) ranged from 0.88 to 0.92, indicating slightly to strongly absorbing aerosols. Absorption AOD440 nm values were 0.01 at the remote sites versus 0.07 at the urban sites. The average direct aerosol radiative effect (DARE) at the bottom of atmosphere increased from the sites in the remote areas (−24.40 W m−2) to the urban areas (−103.28 W m−2), indicating increased cooling at the latter. The DARE for the top of the atmosphere increased from −4.79 W m−2 at the remote sites to −30.05 W m−2 at the urban sites, indicating overall cooling effects for the Earth–atmosphere system. A classification method based on SSA440 nm, fine-mode fraction (FMF), and EAE440–870 nm showed that coarse-mode particles (mainly dust) were dominant at the rural sites near the northwestern deserts, while light-absorbing, fine-mode particles were important at most urban sites. This study will be important for understanding aerosol climate effects and regional environmental pollution, and the results will provide useful information for satellite validation and the improvement of climate modelling.

Huizheng Che↗
NASA NTRS1974

Effect of Various Material Properties on the Adhesive Stage of Fretting

Various properties of metals and alloys were studied with respect to their effect on the initial stage of the fretting process, namely adhesion. Crystallographic orientation, crystal structure, interfacial binding energies of dissimiliar metal, segregation of alloy constituents and the nature and structure of surface films were found to influence adhesion. High atomic density, low surface energy grain orientations exhibited lower adhesion than other orientations. Knowledge of interfacial surface binding energies assists in predicting adhesive transfer and wear. Selective surface segregation of alloy constituents accomplishes both a reduction in adhesion and improved surface oxidation characteristics. Equivalent surface coverages of various adsorbed species indicate that some are markedly more effective in inhibiting adhesion than others.

Buckley, D. H.↗
NASA NTRS1993

Workshop on the Space Environment: The Effects on the Optical Properties of Airless Bodies

Reflectance spectrophotometry and polarimetry are major tools in remote sensing studies of surfaces of solar system bodies. The interpretations of such measurements are often based on laboratory studies of meteoritic, lunar, and terrestrial materials. However, the optical properties of regoliths are known to be affected by the space environment. Thus, some of the major questions addressed in the workshop include identity of the soil component responsible for alteration of the optical properties, the process that produced this component, and how reliably the effects of these processes could be extrapolated to other bodies of the solar system.

Hapke, B.↗
DOE OSTI2022

PolyDODT: a macrocyclic elastomer with unusual properties

The effect of reaction conditions on the structure of poly(3,6-dioxa-1,8-octanedithiol) (polyDODT) made by Reversible Radical Recombination Polymerization (R3P) using triethylamine (TEA), H 2 O 2 and air was investigated. 800 MHz (1 and 2D) NMR was used to investigate the polymer structures. Sensitivity analysis provided direct evidence for high purity cyclic polyDODT up to M n ~ 100 000 g mol –1 . Here, comparative analysis by High Resolution Multidetector Size Exclusion Chromatography (SEC) using integrated data showed that the cycles had lower viscosity and were more compact (both for R g and R h ) than linear samples of similar molecular weight. However, differential data revealed unusual behavior. While lower molecular weight cyclic polymers eluted later and had lower intrinsic viscosity than their linear counterparts at the same molecular weight, at higher molecular weights the polymers showed strange behavior: both the diffusion coefficient measured by Quasielastic Light Scattering (QELS) and Mark–Houwink–Sakurada plots of intrinsic viscosity for linear and cyclic polyDODT were found to converge. R3P, an aqueous based “green” method is capable of producing polymers at the 10–100 g scale in the lab, which will allow more detailed studies of this new class of biodegradable elastomers so further experimentation can be performed to elucidate the reasons for the unusual findings.

36 MATERIALS SCIENCE↗
NASA NTRS1990

Influence of 7 days of hindlimb suspension and intermittent weight support on rat muscle mechanical properties

The effect of intermittent periods of weight support on a decrease in mass of the soleus (Sol) and medial gastrocnemius (MG) muscles atrophied by hindlimb suspension (HS) was investigated in rats subjected to continuous HS for seven days or an HS plus intermittent (10 min every 6 hrs of slow walking on a treadmill) weight support (HS-WS). After 7 d HS, the Sol weight relative to body weight was 21 and 9 percent lower in Hs and HS-WS, respectively, than in control rats. Maximum tetanic tension/muscle mass ratio was significantly lower in HS than in controls; the HS-WS rats had values similar to controls, whereas the maximum tetanic tension/muscle weight was significantly elevated in HS-WS compared to controls. Contraction times were 25 percent faster in the Sol and unchanged in the MG of HS rats, indicating that a low-force short-duration exercise regime results in a significant functional recovery in the 'slow' Sol, whereas the 'fast' MG is less affected.

Pierotti, David J.↗
NASA NTRS2022

Optical properties of morphologically complex black carbon aerosols: Effects of coatings

Optical properties are computed for fractal-like aggregate black carbon (BC) aerosols coated with different substances. Two models are used for these aerosols: (i) the coated aggregate model (model I), where coating is added to the voids and surroundings of BC fractal-like aggregates; and (ii) the closed-cell aggregate model (model II), where coating is added concentrically to each monomer of BC fractal-like aggregates. Our results favor choosing the coated aggregate model (model I) to simulate scattering and absorption by coated BC aerosols because this model is morphologically more realistic, and because this model yields mass absorption cross section (MAC) and backscattering linear depolarization ratio (LDR) values that are consistent with field measurements. Moreover the corresponding computed degree of linear polarization (DoLP) and LDR values are very sensitive to changes in the coating volume fraction (fvol) and the coating refractive index (m). With the same absorbing BC core, the MAC value increases steadily with increasing fvol and m values. For example, using a density of 1.8 g/cm 3 and BC refractive index 1.95 + i0.79, the calculated MAC values for uncoated BC aggregates range from 6.2 to 6.8 m 2 /g at 0.55 µm. When coating material is applied to the BC aggregates, the calculated MAC values for model I particles increase to between 9.8 and 13.2 m 2 /g (depending on m) when fvol = 87.5%. The backscattering LDR values also tend to increase with the increasing m values for the shapes and sizes considered in our study. For model I particles, the backscattering LDR values span a wide range of 4.2–27.8% at a wavelength of 0.35 µm at fvol = 87.5% when m increases from 1.33 to 1.55. Our results are relevant to analyses of polarimetric and lidar observations of smoke particles, especially when these particles undergo hygroscopic growth.

Black carbon aerosols↗
NASA NTRS1990

The effect of neutron irradiation on the properties of AlGaAs/GaAs laser diodes

The effects of neutron irradiation on several properties of both single and multiple stripe laser diodes have been examined. Prior to fast neutron irradiation, total light output as a function of laser current, threshold current, near-field pattern, far-field pattern, and laser output wavelength spectra were measured at room temperature. These measurements were then repeated at intermittent neutron fluence levels. It was observed that the threshold current increased with neutron fluence for all devices examined. In contrast, neutron irradiation had only an indirect effect on the remainder of the laser diode properties in that the higher currents required for operation after irradiation caused variations in these properties.

Barnes, C. E.↗
DOE OSTI2024

Alloying Effects on the Transport Properties of Refractory High-entropy Alloys

Additive Manufacturing (AM) has opened new frontiers for the design of refractory high-entropy alloys (HEAs) for high-temperature applications. The thermal conductivity of the AM feedstock is among the most important thermo-physical properties that control the melting and solidification process. Despite its significance, there remains a notable gap in both computational and experimental research concerning the thermal conductivity of HEAs. Here, we use density functional theory (DFT) to systematically investigate the alloying effects on the transport properties of Ti-Cr-Mo-W-V-Nb-Ta RHEAs, including electrical and thermal conductivities and Seebeck coefficient. The relaxation time of charge carriers is a key underlying parameter determining thermal conductivity that is exceedingly challenging to predict from first principles alone, and we thus follow the approach by Mukherjee, Satsangi, and Singh [Chem Mater 32, 6507 (2022)] to optimize the relaxation time for RHEAs. Here we validated thermal conductivity predictions on elemental solids, binary and ternary alloys, and RHEAs and compared them against thermodynamic (CALPHAD) predictions and our experiments with good correlations. To understand observed trends in thermal conductivity, we assessed the phase stability, electronic structure, phonon, and intrinsic- and tensile strength of down-selected RHEAs. Our electronic structure and phonon results connect well with the observed compositional trends for thermal transport in RHEAs. Our DFT assessment and CALPHAD predictions provide a unique design guide for RHEAs with tailored thermal conductivity, a critical consideration for AM and thermal-management applications.

36 MATERIALS SCIENCE↗
NASA NTRS2016

Cirrus Heterogeneity Effects on Cloud Optical Properties Retrieved with an Optimal Estimation Method from MODIS VIS to TIR Channels.

This study presents preliminary results on the effect of cirrus heterogeneities on top-of-atmosphere (TOA) simulated radiances or reflectances for MODIS channels centered at 0.86, 2.21, 8.56, 11.01 and 12.03 micrometers , and on cloud optical properties retrieved with a research-level optimal estimation method (OEM). Synthetic cirrus cloud fields are generated using a 3D cloud generator (3DCLOUD) and radiances/reflectances are simulated using a 3D radiative transfer code (3DMCPOL). We find significant differences between the heterogeneity effects on either visible and near-infrared (VNIR) or thermal infrared (TIR) radiances. However, when both wavelength ranges are combined, heterogeneity effects are dominated by the VNIR horizontal radiative transport effect. As a result, small optical thicknesses are overestimated and large ones are underestimated. Retrieved effective diameter are found to be slightly affected, contrarily to retrievals using TIR channels only.

MODIS↗
NASA NTRS1975

Effect of various material properties on the adhesive stage of fretting

Various properties of metals and alloys have been studied with respect to their effect on the initial stage of the fretting process, namely adhesion. Crystallographic orientation, crystal structure, interfacial binding energies of dissimiliar metal, segregation of alloy constituents and the nature and structure of surface films have all been found to influence adhesion. High atomic density, low surface energy grain orientations exhibit lower adhesion than other orientations. Hexagonal metals in general manifest less adhesive wear than cubic metal. Knowledge of interfacial surface binding energies can assist in predicting adhesive transfer and wear. Selective surface segregation of alloy constituents can accomplish both a reduction in adhesion and improved surface oxidation characteristics. Equivalent surface coverages of various adsorbed species indicate that some are markedly more effective in inhibiting adhesion than others.

Buckley, D. H.↗
NASA NTRS1974

Effect of various material properties on the adhesive stage of fretting

Various properties of metals and alloys have been studied with respect to their effect on the initial stage of the fretting process, namely adhesion. Crystallographic orientation, crystal structure, interfacial binding energies of dissimiliar metal, segregation of alloy constituents and the nature and structure of surface films have all been found to influence adhesion. High atomic density, low surface energy grain orientations exhibit lower adhesion than other orientations. Hexagonal metals in general manifest less adhesive wear than cubic metal. Knowledge of interfacial surface binding energies can assist in predicting adhesive transfer and wear. Selective surface segregation of alloy constituents can accomplish both a reduction in adhesion and improved surface oxidation characteristics. Equivalent surface coverages of various adsorbed species indicate that some are markedly more effective in inhibiting adhesion than others.

Buckley, D. H.↗