Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EXCEPTIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Hypersonic aerodynamics and entry-maneuver: Aerothermodynamic interactions for two lifting entry vehicles

The longitudinal, directional, and lateral static stability and control characteristics of a delta lifting body and a delta-wing body were obtained at a Mach number of 20 in helium for operational Reynolds numbers over an angle-of-attack range of -4 deg to 55 deg. The aerodynamic characteristics of the wing body were then evaluated in an entry study to examine the effects of vehicle performance on the aerothermodynamic parameters associated with constant and variable angle-of-attack modes for a 1500-n. mi. cross range. The experimental results indicated that the vehicles were stable, except for neutral directional stability for the wing-body shape, and could be trimmed over the operational angle-of-attack range; however, the wing-body vehicle had adverse yaw due to roll control. This roll-yaw coupling was not examined for the lifting body. The trajectory analysis indicated that a 17-percent decrease in performance required little change in the constant angle-of-attack entry mode and, in turn, resulted in a small decrease in the total heat load. For the pitch-modulated entry, the performance decrease required the pitch maneuver to begin earlier during entry and to last longer in order to meet the 1500-n. mi. cross range without a major heating penalty. The performance reduction also had little effect on the maximum laminar radiation equilibrium temperature over a major portion of the lower surface of the wing-body vehicle regardless of the entry mode.

Arrington, J. P.↗

Measured noise of model fan-under-wing and fan-on-flap jet flap configurations

Noise measurements were made on two jet flap systems proposed for STOL aircraft. In one case a 14.0-cm- (5.5-in.-) diameter fan was mounted under the wing such that the exhaust impinged on downwardly deflected flap segments. In the other case, the fan was located on the upper surface of the flap such that fan and flap moved as a unit, with no exhaust impingement. Results for takeoff and approach fan speeds and flap deflections were used to estimate STOL airplane perceived noise levels. Internally generated noise directivity corresponded with fan axis orientation for the fan-on-flap, but no consistent redirection of internal noise was observed with changes in flap angle for the fan-under-wing. With the fan-on-flap arrangement, the wing shielded some fan inlet noise from the ground. Since no impingement of the exhaust on solid surfaces occurred, the external noise was jet noise alone. In contrast, for the fan-under-wing, the jet/flap interaction noise dominated the external noise except at angles near the jet axis even with no flap deflection. If internal noise is reduced by fan design and acoustic treatment, the jet/flap interaction noise will dominate.

Groeneweg, J. F.↗

Polynomial filter estimation of range and range rate for terminal rendezvous

A study was made of a polynomial filter for computing range rate information from CSM VHF range data. The filter's performance during the terminal phase of the rendezvous is discussed. Two modifications of the filter were also made and tested. A manual terminal rendezvous was simulated and desired accuracies were achieved for vehicles on an intercept trajectory, except for short periods following each braking maneuver when the estimated range rate was initially in error by the magnitude of the burn.

Philips, R.↗

Effects of body shape on the aerodynamic characteristics of an all-body hypersonic aircraft configuration at Mach numbers from 0.65 to 10.6

An experimental investigation was conducted to determine the effects of several variations in body shape on the aerodynamic characteristics of an all-body hypersonic aircraft configuration. The basic configuration had a delta planform with an elliptic cone forebody and an afterbody of elliptic cross section terminating in a straight-line trailing edge. Variations in body shape included the ratio of maximum cross-sectional to body planform area, body leading-edge sweep, and forebody length ratio. In addition, the effects of a thin wing mounted on one of the bodies was investigated, and the aerodynamic characteristics of just the forebodies of two of the configurations were determined. The models had no stabilizing surfaces or propulsion system packages. Ranges of angle of attack (-4 deg to +15 deg) and angle of sideslip (-4 deg to +8 deg) were investigated. Of the four complete bodies, the configuration with the lowest ratio of cross-sectional to body planform area had the highest maximum lift-drag ratio and the greatest level of longitudinal stability at most Mach numbers. All the configurations had positive longitudinal stability near maximum lift-drag ratio at most Mach numbers. With exception of the lowest subsonic Mach numbers, changes in body sweep angle and in forebody length ratio had only minor effects on maximum lift-drag ratio.

Nelms, W. P., Jr.↗

State-of-technology for joining TD-NiCr sheet

At the current state-of-technology there are many joining processes that can be used to make sound welds in TD-NiCr sheet. Some of these that are described in this report are electron beam welding, gas-tungsten arc welding, diffusion welding, resistance spot welding, resistance seam welding, and brazing. The strengths of the welds made by the various processes show considerable variation, especially at elevated temperatures. Most of the fusion welding processes tend to give weak welds at elevated temperatures (with the exception of fusion-type resistance spotwelds). However, solid-state welds have been made with parent metal properties. The process used for a specific application will be dictated by the specific joint requirements. In highly stressed joints at elevated temperatures, one of the solid-state processes, such as DFW, RSW (solid-state or fusion), and RSEW, offer the most promise.

Holko, K. H.↗

A method for the measurement and analysis of ride vibrations of transportation systems

The measurement and recording of ride vibrations which affect passenger comfort in transportation systems and the subsequent data-reduction methods necessary for interpreting the data present exceptional instrumentation requirements and necessitate the use of computers for specialized analysis techniques. A method is presented for both measuring and analyzing ride vibrations of the type encountered in ground and air transportation systems. A portable system for measuring and recording low-frequency, low-amplitude accelerations and specialized data-reduction procedures are described. Sample vibration measurements in the form of statistical parameters representative of typical transportation systems are also presented to demonstrate the utility of the techniques.

Catherines, J. J.↗

Life prediction of expulsion bladders through fatigue test and fold strain analysis

Cycle life data are presented in terms of true maximum strain for four metals, two plastics, and two elastomers. The Coffin-Manson fatigue theory was applied for metals and plastics, and cut-growth fatigue theory for elastomers. The data are based on measurements made at room and elevated temperatures. It was found that double folds give rise to far severer folding strains than do simple folds. It was also found that, except for the elastomers, all the bladder materials develop surface cracks due to double folds after only one cycle. The findings indicate that metals, which are bets for premeation resistance, are worst for fatigue resistance, and vice versa for elastomers. The intermediate plastics were found to be unsatisfactory for both permeation and fatigue resistance for missions of extended duration.

Chu, H. N.↗

Two Phase Detonation Studies Conducted in 1971

The research covered by this third annual progress report represents a continuation of our efforts devoted to the study of detonation waves in liquid-gas systems. The motivation for the work is associated with liquid propellant rocket motor combustion instability although certainly the studies are also applicable to internal combustion engines, jet propulsion engines, safety aspects of spilled liquid fuel, coal mine explosions, and weaponry. The research has been divided into 5 phases, although all of them are intimately related. For the most part these phases are briefly summarized and the reader is referred to other publications for a more complete treatment. The exception to this is where the material herein represents the only printed information available on the particular facet of the problem. Phase A has been primarily concerned with the breakup and ignition of fuel drops by shock waves. The experimental portion of this study as well as a theoretical treatment of the ignition behavior was completed in the past year. The research is now concentrating on the passage of a shock wave over a burning drop. Phase B has been devoted to the assessment of the approximate energy release pattern in two phase detonations insofar as they affect the significant overpressures observed.

Nicholls, J. A.↗

Lunar mass spectrometer test program

The procedures are described along with results obtained in a test program conducted to demonstrate the performance of a candidate lunar mass spectrometer. The instrument was designed to sample and measure gases believed to exist in the lunar atmosphere at the surface. The subject instrument consists of a cold cathode ion source, a small quadrupole mass analyzer and an off axis electron multiplier ion counting detector. The major program emphasis was placed on demonstrating instrument resolution, sensitivity and S/N ratio over the mass range 0-150 amu and over a partial pressure range from 10 to the minus 9th power to 10 to the minus 13th power torr. Ultrahigh vacuum tests were conducted and the minimum detectable partial pressure for neon, argon, krypton and xenon was successfully determined for the spectrometer using isotopes of these gases. With the exception of neon, the minimum detectable partial pressure is approximately 4 x 10 to the minus 14th power torr for the above gases.

Torney, F. L.↗

An integral test of the inelastic cross sections of Pb and Mo using measured neutron spectra

Comparison of measurements and calculations of fast neutron spectra from a radioactive neutron source inside spheres of Mo or Pb and from a cylindrical reactor containing a thick Pb or Mo reflector are used as a test of ENDF cross sections. The sphere leakage spectra were measured at a sphere-to-spectrometer distance of 2 meters using a 54 Ci spherical Am-Be neutron source. Reactor leakage spectrum measurements were made at the surface of the ZP-1 reactor when bare, with a Pb radial reflector 21 cm thick, and with a metallic Mo radial reflector 10 cm thick. In the case of the thin Mo sphere there is agreement between the calculation and measurement. The Pb calculation is much lower than the measurement except at the highest neutron energy. Two-dimensional calculations of reactor spectra result indicate that the reactor source is reasonably well known. Significant differences in leakage spectrum shape for both Mo and Pb reflectors suggest that there are large uncertainties in the inelastic cross sections for Pb and some for Mo.

Shook, D. F.↗

High voltage transmission microscopy of Surveyor 3 camera shrouds

The internal structure of painted and unpainted aluminum alloy sheet samples from the TV camera shrouds were examined by high-voltage transmission electron microscopy. No clear-cut evidence of radiation damage effects was observed. Noticeable differences in microstructures between the upper visor and the sides and bottom of the lower shroud suggest different thermal histories, and the maximum temperatures due to solar heating are estimated to be between 164 and 319 C. Some correlation between microstructures and maximum estimated temperature is noted. It is felt that the apparent temperature rise due to solar heating will not affect the structural integrity of spacecraft components except possibly for very long periods of exposure. However, substantial thermal diffusion could affect interpretation of solar wind rare gas studies.

Fisher, R. M.↗

Lunar roving vehicle magnetic tests

The qualification model of the lunar roving vehicle (LRV) was tested in the Spacecraft Magnetic Test Facility (SMTF) at the GSFC Magnetic Test Site. Magnetic field measurements were made, both with the vehicle in its as received state and also subsequent to final deperm treatment. These measurements, together with information supplied to GSFC regarding the magnetic moment of the astronaut's extravehicular mobility units (EMU's) were used to calculate 0.5 nanotesla (gamma) contours around the LRV. The results are tabulated. Magnetic field measurements were also made with various items of LRV equipment operational. No significant changes were noted, except during operation of the vehicle wheels.

Boyle, J. C.↗

The measurement of radiation exposure of astronauts by radiochemical techniques

The urine specimens collected pre- and postflight from the Apollo 15 mission were analyzed for their radionuclide content. Cosmic radiation dose estimates of 695 and 660 mR are calculated from the observed Na-22 and Na-24 concentrations respectively. The concentrations of Na-22, Na-24, K-40, K-42, Cr-51, Fe-59, and Cs-137 are given. The potassium excretion patterns of high postflight and low preflight levels established for previous missions appears to be reversed for this mission. The concentrations of 23 major, minor, and trace elements in the fecal samples from the Apollo 14 astronauts are reported. Most elemental excretion rates are comparable to rates reported for earlier missions. The major exception is potassium where loss rates are the lowest ever observed. This coincides with the anomalously low excretion of potassium in postflight urine specimens. Apparent mass balance of calcium and iron continues as in the Apollo 12 and 13 missions.

Brodzinski, R. L.↗

Studies of effects of closed microbial ecology. Report of 180-day test period

Experiments were performed to determine the influence closed microbial ecologies have on modification or simplification of natural intestinal flora of ferrets in a closed environmental system. On the basis of previous tests in which certain species (Salmonella and Bacteroides) were decreased at 90 days of enclosure, a second trial was constructed for 180-day tests. In this trial there was little difference in the 8 major classes of intestinal flora between animals in the Open and Closed environmental groups except for the level of Lactobacillus. It is of extreme importance to note that when both Open and Closed groups contracted hemorrhagic gastritis, the interrelationship of this agent with other intestinal flora produced a more profound effect on animals from the Closed Group, particularly with reference to Lactobacillus levels.

Kenyon, A. J.↗

Survival of bacterial isolates exposed to simulated Jovian trapped radiation belt electrons and solar wind protons

With missions to Jupiter, the spacecraft will be exposed for extended duration to solar wind radiation and the Jovian trapped radiation belt. This study is designed to determine the effect of these radiation environments on spacecraft bacterial isolates. The information can be used in the probability of contamination analysis for these missions. A bacterial subpopulation from Mariner Mars 1971 spacecraft (nine sporeforming and three nonsporeforming isolates) plus two comparative organisms, Staphylococcus epidermidis ATCC 17917 and a strain of Bacillus subtilis var. niger, were exposed to 2-, 12-, and 25-MeV electrons at different doses with simultaneous exposure to a vacuum of 0.0013 N/sqm at 20 and -20 C. The radioresistance of the subpopulation was dependent on the isolate, dose, and energy of electrons. Temperature affected the radioresistance of only the sporeforming isolates. Survival data indicated that spores were reduced approximately 1 log/1500 J/kg, while nonsporeforming isolates (micrococci) were reduced 1.5 to 2 logs/1500 J/kg with the exception of an apparent radioresistant isolate whose resistance approached that of the spores. The subpopulation was found to be less resistant to lower energy than to higher energy electrons.

Taylor, D. M.↗

Evaluation of advanced component concepts for an integrated environmental control/life support, resistojet control system

Flow restricting devices were studied for their suitability as liquid water propellant flow limiters for the biowaste resistojet. Flow limiting during the start-up transient is required to prevent thrustor instabilities and icing which could result in heater failure in the electrical resistance heated thrustor (resistojet). The study was directed toward simple devices which would function passively (i.e., without power except from the propellant flow itself), and would offer high reliability and simplicity. In addition to the flow limiting devices, a thermal pumping system was studied to determine whether CO2, desorbed from molecular sieves could be pumped thermally in a space station application. The thermal pump is considered a possible replacement for mechanical pumps. It involves a cyclic, constant volume cryopumping system which employs space radiators to achieve the cryotemperatures. The frozen CO2 would be vaporized periodically, using a waste heat loop, to attain sufficient pressure to transfer a large portion of the trapped CO2 to storage tanks.

Halbach, C. R.↗

NASTRAN: User experience with four example problems

Four different structural problems are solved to gain familiarity with the NASTRAN computer program. The problems are: (1) a simply-supported beam subjected to lateral loads, (2) a rotating filamentary composite bar under the action of centrifugal forces, (3) a missile body with aerodynamic, gravitational, and inertial forces, and (4) a square simply-supported plate with in-plane temperature changes capable of buckling the plate. Input and output data are given for each problem. The results are compared with those obtained by other methods. However, except for the examples employing beam elements in which the agreement is excellent, the element breakup chosen for convenience in obtaining program familiarity is too coarse to draw conclusions regarding the program accuracy. The example problems disclosed errors in the plotting and thermal-buckling routines of the program.

Rivello, R. M.↗

Numerical solutions of several reflected shock-wave flow fields with nonequilibrium chemical reactions

The method of characteristics for a chemically reacting gas is used in the construction of the time-dependent, one-dimensional flow field resulting from the normal reflection of an incident shock wave at the end wall of a shock tube. Nonequilibrium chemical reactions are allowed behind both the incident and reflected shock waves. All the solutions are evaluated for oxygen, but the results are generally representative of any inviscid, nonconducting, and nonradiating diatomic gas. The solutions clearly show that: (1) both the incident- and reflected-shock chemical relaxation times are important in governing the time to attain steady state thermodynamic properties; and (2) adjacent to the end wall, an excess-entropy layer develops wherein the steady state values of all the thermodynamic variables except pressure differ significantly from their corresponding Rankine-Hugoniot equilibrium values.

Hanson, R. K.↗