Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EDL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

MARS 2020 Backshell Radiative Heating Measurement and Shock Tube Verification

In February 2021, the Perseverance rover was brought to the surface of Mars by the Mars 2020 mission. A feature of the Mars 2020 capsule was instrumentation to measure its entry, descent and landing (EDL) with the so-called Mars EDL Instrumentation 2 (MEDLI2) [1]. The MEDLI2 introduced, among other things, backshell instrumentation, including a broadband radiometer. The radiometer was mounted on the leeside of the vehicle next to thermocouple plugs and a heat flux gauge. The data returned by the leeside MEDLI2 heat flux gauge is largely analogous to that measured by the COMARS gauge flown on the ExoMars Schiaparelli [2] entry in that it is measuring heat flux in an area that is entirely dominated by radiative heating. The COMARS measurement provided excellent validation of backshell radiative heating models for Mars entry, albeit at a limited number of points [3]. The MEDLI2 heat flux gauge measurement effectively confirmed the quality of the prediction, extended over the full trajectory, as will be presented in this paper. The MEDLI2 radiometer,however, was blocked by ablation products and suffered a loss of half of its signal. The second backshell heat flux gauge installed on the windside of the vehicle was also well predicted, although the heating had both radiative and convective contributions. It was desired to reproduce the conditions of the Mars 2020 entry via ground testing in the Electric Arc Shock Tube (EAST) at NASA Ames. Tests to verify stagnation line heating were previously reported in EAST, confirming the presence of shock layer radiation as the major discrepancy in heatshield temperature modelling [4]. Therefore, tests for stagnation line heating were not repeated. Instead, the shock tube informed bias method [5, 6] was used to identify test conditions that may produce similarity to streamlines that pass around the backside of the vehicle and are responsible for the radiation observed at the two heat flux gauge locations. This method was used to identify a range of velocities and densities in the shock tube that are relevant for confirming the radiative environment encountered. This paper reports the results obtained in the 10 cm diameter EAST shock tube, corresponding to later trajectory points at ambient pressures of 1.1-2.0 Torr and velocities from 1.2-3.5 km/s. The test series employed two primary diagnostics: emission spectroscopy and tunable diode laser absorption spectroscopy (TDLAS). The emission spectroscopy performed broadband measurements of the radiative emission of the 4.3 and 2.7 m bands of CO2 at flight similar conditions, obtaining both spectral and spatial data corresponding to the relaxation behind the shock front. The TDLAS measured the absorption of several lines of CO and CO2 and obtains species number densities and temperatures as a function of time behind the shock front. This paper will review highlights of this test series and analyses of the emission and absorption data. While the datasets generally show good agreement with predictions, a few discrepancies and items for additional investigation are identified and will be discussed

Brett A Cruden↗

Entry, Descent, and Landing GN&C System Evaluation via Cable-Driven Emulation Robotics

An innovative cable-driven parallel robot named the Six Degree-of-Freedom Tendon Actu- ated Robot (STAR), recently developed by researchers at NASA Johnson Space Center, was built to enable entry, descent, and landing (EDL) emulation experiments. Upon functional testing and system verification, STAR employed several simulated EDL trajectories to validate velocimeter LIDAR-based sensor models for cooperative terrain relative navigation applica- tions for its first testing campaign. The STAR lab also hosted researchers from Astrobotic to evaluate the real-time performance of a newly developed sensor payload, UltraNav, through hardware in-the-loop-testing (HWIL). This work introduces the STAR system along with its accompanying testing utilities and capabilities, and deliver the experimental methodology and results of test campaigns performed with the STAR facility to date.

navigation↗

Silicon Photonic Transceiver for Spacecraft Navigational Lidar

NASA is developing an entry, descent, and landing (EDL) lidar system, the Navigation Doppler Lidar (NDL), for high-precision landing on the Moon, Mars, and beyond. The current flight NDL systems use 1550 nm fiber-optic components for frequency-modulated continuous wave (FMCW) ranging beyond 5 km, but have reduced performance under vibrational and thermal stresses during EDL. Here we describe recent efforts to develop a breadboard silicon photonic optical transceiver for integration into NDL to reduce instrument size and improve robustness to environment and demonstrate the optical balanced receiver performance during testing with the breadboard NDL unit. Initial testing shows improved suppression of common mode noise by 25 dB over the current receiver, but a 10 dB reduction in signal to noise ratio (SNR) resulting from coupling losses from fiber to the on-chip waveguides. Future work will target reduced coupling loss, hermetic packaging, and co-integration of a single sideband suppressed carrier modulator into the same chip.

Photonic Integrated Circuits↗

New Developments In NASA’s Entry Systems Modeling Project

This paper describes recent developments for modeling entry, descent, and landing (EDL)of spacecraft in support of NASA’s exploration missions. Mission-specific research and model development for entry systems occurs across the Agency (e.g., within flight programs like Artemis/Orion and Mars Sample Return), however the aim of this paper is to discuss the research conducted by NASA’s Entry Systems Modeling (ESM) Project, which serves as the Agency’s only effort dedicated to advancing modeling capabilities that cross-cut multiple technical disciplines, missions and destinations. The ESM portfolio is developed to address the specific needs expressed by a cross-section of NASA stakeholders, including flight and research projects, technical leadership, and subject matter experts. Technology development in ESM is organized and prioritized from a system-level perspective, resulting in four broad technical areas of investment: (1) Thermal Protection System (TPS) material modeling, (2) Shock layer kinetics and radiation, (3) Aerosciences, and (4) Guidance, navigation, and control. In addition to the core technical areas, special topics are rolled into the project portfolio as specific demands arise. Current special topics include TPS Certification by Analysis, improving understanding of woven TPS material performance; Hypersonic Wake Flows, assessing and improving predictions of base flows; and the MEDLI2 Deep Dive, furthering analysis of data obtained during Mars2020 mission’s entry and descent at Mars. Key results from each of these areas are presented in this paper, along with associated references to serve as a roadmap for other EDL researchers to access NASA’s publications.

Aaron M Brandis↗

Entry Systems Modeling and Ground Testing: Enabling Flight Performance and Risk Reduction

Entry, Descent, and Landing (EDL) comprise a relatively small portion of a mission’s timeline, however, it is typically among the largest risks. Flying through a body’s atmosphere reliably and accurately – from orbit to ground or via aerocapture – is a critical step toward successful in situ exploration. This exhibit will highlight EDL simulation and ground test capabilities, both existing and under development, that could support mission design, risk reduction, and post-flight analysis for Planetary Science mission concepts displayed in the 2023 SMD Planetary Science Technology Showcase.

Entry Systems↗

Entry, Descent, and Landing Communications for the Mars 2020 Lander Mission

The Mars 2020 mission was launched on July 30, 2020 and successfully landed in Jezero Crater on February 18, 2021. The challenging Entry, Descent, and Landing (EDL) sequence was observed by ground stations on Earth and by orbiters at Mars. This paper discusses the design of the launch and arrival period to ensure maximum Earth visibility, the details of phasing the orbiting assets, and the development of the entry relay targets needed to ensure robust spacecraft telecommunications during EDL.

Abilleira, Fernando↗

The Mars 2020 Perseverance Navigation Filter

The Mars 2020 (M2020) Entry Descent and Landing (EDL) system delivered a rover named “Perseverance” at Jezero crater (Mars) on February 18th, 2021. M2020 EDL used a Guidance Navigation and Control (GN&C) system to achieve its landing target objectives. The navigation filter (NavFilter) integrated Descent Inertial Measurement Unit (DIMU) measurements to estimate position and attitude. The NavFilter also used the Terminal Descent Sensor (TDS) to es-timate surface-relative position and velocity corrections. The NavFilter provided all of the dynamic state information to the entry controller, entry guidance, Lander Vision System (LVS) and powered descent guidance and control algo-rithms. The NavFilter for Perseverance is based on Curiosity’s NavFilter with a couple of modifications.

Casoliva, Jordi↗

Mid-Air Helicopter Delivery at Mars Using a Jetpack

Mid-Air Helicopter Delivery (MAHD) is a new Entry, Descent and Landing (EDL) architecture to enable in situ mobility for Mars science at lower cost than previous rover missions. It uses a jetpack to slow down a Mars Science Helicopter (MSH) after separation from the backshell, and reach aerodynamic conditions suitable for helicopter take-off in mid air. MAHD's lander-free approach leaves enough room in the aeroshell to accommodate larger rotors. This drastically improves flight performance compared to heritage EDL approaches, notably +60\% science payload mass. MAHD also brings cost savings, a simpler architecture, improved surface access and can reach higher elevations on Mars. This paper introduces a design for the MAHD system architecture and operations. We present a mechanical configuration which fits both MSH and the jetpack within the 2.65-m Mars heritage aeroshell, and a jetpack control architecture which fully leverages the available helicopter avionics. We discuss preliminary numerical models of the flow dynamics resulting from the interaction between the jets, the rotors and the side winds. We define a force-torque sensing architecture capable of handling the wind and trimming the rotors to prepare for safe take-off. Finally, we analyze the dynamic environment and closed-loop control simulation results to demonstrate the preliminary feasibility of MAHD.

Balaram, J.↗

Developments to the Ares Multi-Physics Framework

Increasingly challenging problems in Entry, Descent, and Landing (EDL) have motivated the development of a computational framework that encompasses the advances in high-fidelity modeling and a robust foundation for TPS design in a single software package. This is the objective of the Ares multi-physics solver which, to date, couples the US3D flow solver with Icarus (material response) and Nero (radiation), through detailed time-scale management, while also incorporating the physics of fluid-solid boundaries such as gas-surface interaction chemistry and shape change. Ares, which is currently in the development stage, is being assessed against a variety of EDL relevant problems such as arc-jet tests of varying geometries and materials (Figs. 1 and 2), the earth entry of MSR-EES and the Titan entry of Dragonfly. This presentation will focus on the findings to-date regarding development of the technology as well as its standing with respect to available experimental data and/or reference solutions.

CFD↗

Development of a Surface Water Transportation System for ISRU Operations on Mars

NASA is working to define the architecture needed for a Mars exploration campaign. Initial analysis assumptions allow for pre-deployment of essential cargo and equipment to support a crew landing, including the pre-positioning of a Mars Ascent Vehicle (MAV). This MAV is likely to represent the largest single payload that must be landed on the Mars surface. Its size would be influenced by the amount of mass that state-of-the-art Entry, Descent, and Landing (EDL) systems would be capable of placing on Mars. One possible method of increasing the usable size of the MAV without exceeding available EDL capabilities is to land the MAV without ascent propellant on board. Following such a method may necessitate a strategy to acquire sufficient ascent propellant to allow a crew to safely depart the Martian surface. This paper describes a conceptual return propellant strategy that uses a liquid transportation skid, or pallet, to be used in conjunction with a rover mobility system to transfer water across the Martian surface from a source point to an in-situ resource utilization (ISRU) plant that would use this water as a feedstock to generate oxygen and methane to enable launch of the MAV. Design considerations, concept of operations, and rover energetics will be discussed in this paper.

Fluid Structure Interface↗

Assessment of a Surface Water Transportation System for ISRU Operations on Mars

NASA is working to define the architecture needed for a Mars exploration campaign. Initial analysis assumptions allow for pre-deployment of essential cargo and equipment to support a crew landing, including the pre-positioning of a Mars Ascent Vehicle (MAV). This MAV is likely to represent the largest single payload that must be landed on the Mars surface. Its size would be influenced by the amount of mass that state-of-the-art Entry, Descent, and Landing (EDL) systems would be capable of placing on Mars. One possible method of increasing the usable size of the MAV without exceeding available EDL capabilities is to land the MAV without ascent propellant on board. Following such a method may necessitate a strategy to acquire sufficient ascent propellant to allow a crew to safely depart the Martian surface. This paper describes a conceptual return propellant strategy that uses a liquid transportation skid, or pallet, to be used in conjunction with a rover mobility system to transfer water across the Martian surface from a source point to an in-situ resource utilization (ISRU) plant that would use this water as a feedstock to generate oxygen and methane to enable launch of the MAV. Design considerations, concept of operations, and rover energetics will be discussed in this paper.

Fluid Structure Interface↗

Entry, Descent, and Landing Analysis for the OSIRIS-REx Sample Return Capsule

The Origins, Spectral Interpretation, Resource Identification, and Security – Regolith Explorer (OSIRIS-REx) sample return capsule (SRC) returned to Earth on September 24, 2023, safely landing in the Utah Test and Training Range (UTTR). To ensure a safe and successful landing, a pair of high-fidelity EDL simulations, based on the Program to Optimize Simulated Trajectories (POST) architecture, were used to regularly assess the latest orbit determination (OD) solution from the navigation team, making predictions on Entry, Descent, and Landing (EDL) performance and SRC landing location. The results from these analyses fed into the decision processes for the final trajectory correction maneuvers (TCM’s) and SRC release. The models and methods of analysis will be discussed and a comparison of the final pre-entry landing prediction against the observed landing location will be presented along with an assessment of the best estimates of day-of-entry environmental conditions.

Scott R Francis↗

NASA Engineering and Safety Center Technical Bulletin No 12-01: Simulation Framework for Rapid Entry, Descent, and Landing Analysis

The NASA Engineering and Safety Center has archived a number of key historic Entry, Descent, and Landing (EDL) simulation models and developed several new models to enhance the capability of the Agency to evaluate a wide range of EDL systems for system analysis studies, preliminary design, mission development and execution, and time-critical assessments. The simulation models developed in this activity can be used to help define the required architectures and investment strategies for future robotic and human exploration missions.

Simulation Framework↗

Long-Term Groundwater Monitoring Report Industrial Area Kennedy Space Center, Florida

This report presents the 2023 groundwater sampling results from the National Aeronautics and Space Administration (NASA) Industrial Area (IA) Long-Term Monitoring (LTM) activities. Due to the project contract ending in 2023, this report presents one year of LTM activities instead of the two-year timeframe presented in previous reports. The NASA IA LTM Program includes the following 12 sites: - Ransom Road Landfill (RRLF) – Solid Waste Management Unit (SWMU) 003 - Building M7-0505 Treatment Tank Area (M505) – SWMU 039 - Operations and Checkout Building (O&C) – SWMU 076 - Vertical Processing Facility (VPF) – SWMU 077 - Environmental Health Facility (EHF) – SWMU 079 - Kennedy Athletic, Recreation, and Social Park 1 (KARS Park 1) – SWMU 084 - Engineering Development Laboratory (EDL) – SWMU 085 - Launch Equipment Test Facility (LETF) – SWMU 091 - Mobil Service Station (MOBIL) – SWMU 093 - General Services Administration Seized Property (GSSP) – SWMU 095 - Space Station Processing Facility (SSPF) – SWMU 098 - Fuel Storage Area #1 Underground Storage Tank [Building 1044] (FSA1) – Potential Release Location (PRL) 157 Sampling events for the IA LTM Program are conducted seasonally during the dry and wet seasons, which occur in May and November, respectively. The sites in the NASA IA LTM Program are sampled on annual, biennial, or 5-year sampling frequencies based on historical trends. The current sampling frequencies for the NASA IA LTM sites are as follows: - FSA1 is sampled annually, alternating between wet and dry seasons. - GSSP is sampled annually during the wet season. - Seven sites are sampled biennially, alternating between the wet and dry seasons (RRLF, M505, O&C, VPF, LETF, MOBIL, and SSPF). - EHF and EDL are sampled biennially during the wet season. - KARS Park 1 is sampled once every 5 years.

remediation↗

Low-Earth Orbit Flight Test of an Inflatable Decelerator Modeling and Reconstruction

The Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) mission was a flight test performed on November 10, 2022. LOFTID is an 6 meter diameter Hypersonic Inflatable Aerodynamic Decelerator (HIAD) that is stowed for launch as a secondary payload, inflated in space, and separated from launch vehicle before conducting entry, descent, and landing (EDL).The main objective of the flight test was to demonstrate EDL at scale using HIAD technology at flight conditions relevant for future Earth and Mars missions. LOFTID successfully inflated and separated with a spin rate of 18 deg/s, landed within 1 hour on-parachute off the coast of Hawaii, and was successfully recovered. LOFTID re-entered Earth’s atmosphere at 8 km/s, achieved peak deceleration of 9 Gs and peak heat rate of 40 W/cm2, and demonstrated angle-of-attack stability throughout entirety of flight. On-board instrumentation provided flight data, which was saved onto an ejectable data recorder that was ejected at 18 km and successfully recovered. Despite the loss of inertial measurement unit data, techniques were developed to reconstruct the estimated flight performance as described in this paper. This paper presents the trajectory analysis, aerodynamics modeling, and reconstructed flight performance of the LOFTID re-entry vehicle.

Rohan G Deshmukh↗

Assessment of a Surface Propellant Transportation System Concept for Operations on Mars

NASA is working to define the architecture needed for a Mars exploration campaign. One potential architecture option allows for pre-deployment of essential cargo and equipment to support a crew landing, including the pre-positioning of a Mars Ascent Vehicle (MAV). This MAV is likely to represent the largest single payload that must be landed on the Martian surface. Its size would be influenced by the amount of mass that state-of-the-art Entry, Descent, and Landing (EDL) systems would be capable of placing on Mars. One possible method of increasing the usable size of the MAV without exceeding available EDL capabilities is to land the MAV without its ascent propellant on board. Following such a method may necessitate a strategy to acquire sufficient ascent propellant to allow a crew to safely depart the Martian surface. This paper describes a conceptual return propellant strategy that uses a liquid transportation skid, or pallet, to be used in conjunction with a rover mobility system to transfer cryogenic propellant, consisting of oxygen and methane, across the Martian surface from a delivery lander to the MAV to enable its launch. Design considerations, concept of operations, and rover energetics will be discussed in this paper.

Propellant↗

Assessment of a Surface Propellant Transportation System Concept for Operations on Mars

NASA is working to define the architecture needed for a Mars exploration campaign. One potential architecture option allows for pre-deployment of essential cargo and equipment to support a crew landing, including the pre-positioning of a Mars Ascent Vehicle (MAV). This MAV is likely to represent the largest single payload that must be landed on the Martian surface. Its size would be influenced by the amount of mass that state-of-the-art Entry, Descent, and Landing (EDL) systems would be capable of placing on Mars. One possible method of increasing the usable size of the MAV without exceeding available EDL capabilities is to land the MAV without its ascent propellant on board. Following such a method may necessitate a strategy to acquire sufficient ascent propellant to allow a crew to safely depart the Martian surface. This presentation describes a conceptual return propellant strategy that uses a liquid transportation skid, or pallet, to be used in conjunction with a rover mobility system to transfer cryogenic propellant, consisting of oxygen and methane, across the Martian surface from a delivery lander to the MAV to enable its launch. Design considerations, concept of operations, and rover energetics will be discussed in this presentation.

Surface↗

A review of transport models in charged porous electrodes

There is increased interest in many different processes based upon interactions between a charged solid surface and a liquid electrolyte. Energy storage in capacitive porous materials, ionic membranes, capacitive deionization (CDI) for water desalination, capacitive energy generation, removal of heavy ions from wastewater streams, and geophysical applications are some examples of these processes. Process development is driven by the production of porous materials with increasing surface area. Understanding of the physical phenomena occurring at the charged solid-electrolyte interface will significantly improve the design and development of more effective applied processes. The goal of this work is to critically review the current knowledge in the field. The focus is on concepts behind different models. We start by briefly presenting the classical electrical double layer (EDL) models in flat surfaces. Then, we discuss models for porous materials containing macro-, meso-, and micro-pores. Some of the current models for systems comprising two different pore sizes are also included. Finally, we discuss the concepts behind the most common models used for ionic transport and Faradaic processes in porous media. The latter models are used for simulation of electrosorption processes in porous media.

42 ENGINEERING↗