Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Dynamic feature selection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1997

X-Ray Transmission Microscope Development

We have succeeded in meeting the goals set out in the proposal. A cadre of detector technologies is available to suit the requirements of the experiment. Resolutions of both real-time and absolute limits to resolution exceed the initial aspirations. Obtaining sufficient contrast is still a significant limitation but can be overcome by Judicious selection of the specimen composition. This can only take time and trial and error for a successful result. The 4th generation furnace provides the capability of real-time in-situ observations of composite alloy development. A low detection sensitivity however, has still made it difficult to observe dendritic growth, although it has been 'seen' in raw video; it was not a recordable signal. We have examined flight ampoules with XTM to observe particle and thermocouple placement, crucible flaws and cracks in collaboration with the Particle Pushing and Engulfment flight experiment (Dr. Stefanescu, UA, P.I.). The value of an in flight XTM to guard against experiment failure and safety assurance is obvious. Although not attributable to equipment limitations, a quest to observe particle pushing was not successful. We tried at length to prepare specimens that would demonstrate particle pushing. Instead, we were successful in imaging the interface deformation due to the thermal field distortion of a ceramic particle or void and to compare to calculated shapes. In theory, we should have been able to make major inroads to this field if the particles could be pushed and the velocities adjusted to make critical measurements. On the other hand, critical issues of sample preparation for the PEP flight experiment were established, particularly the clustering of particles and trapped voids. In this regard, the XTM did prove very useful so that flight specimens would work as expected and to perform post flight analysis. Although not a clear result, particle pushing of precipitates was observed in an Al-Si-Mn alloy. It may be that to be pushed, the particles need to be small and have clean surfaces like one might obtain from in-situ precipitation. The ability to image features in real time skill enable more fundamental and detailed understanding of solidification dynamics in microgravity than had previously been possible, thus, allowing the full benefits of microgravity experiments be applied towards rigorous testing of critical solidification models. The XTM is also a valuable tool for post solidification metallography. The 3-dimensional distribution of solute and solidification features within the specimen volume can be viewed without sectioning or other treatment when the solute has sufficiently higher atomic mass than the solvent. Thus the XTM could provide the first practical method for on orbit microstructural (metallographic) analysis by the astronauts or by telescience.

Kaukler, William F.↗
NASA NTRS2020

Mars Ascent Vehicle Hybrid Propulsion Configuration

As part of a Mars Sample Return (MSR) campaign, two Mars Ascent Vehicle (MAV) configurations have been designed in parallel. Each ascent vehicle configuration has a different propulsion system which ultimately leads to two unique vehicle designs. As part of a Preliminary Architecture Assessment (PAA), these vehicle designs were developed to the same level of maturity in order to inform the selection of one of the vehicles as the point of departure design for the campaign. The selection will be made in November 2019. The initial MSR architecture called for a hybrid-based propulsion MAV. This type of propulsion system calls for a solid wax motor that would utilize liquid MON-25 as an oxidizer. Hybrid rocket propulsion allows for more flexibility than traditional solid or liquid propulsion options, and typically benefits from the advantages of both. A hybrid motor can be throttled and shut down easily, and avoids significant risk in manufacturing and handling. On a theoretical level, hybrid motors perform at a higher specific impulse (Isp) than solid motors. The primary disadvantage of hybrid motors comes from additional complexity and significantly less flight heritage and low Technology Readiness Level (TRL). This paper describes the design of the hybrid propulsion configuration. An additional paper will be published describing the design of the solid propulsion configuration1. The hybrid propulsion configuration MAV was developed in 2019 by NASA Marshall Space Flight Center (MSFC) in association with NASA Jet Propulsion Laboratory (JPL). It features a Single Stage to Orbit (SSTO) design with an SP7A solid wax fuel and MON-25 liquid oxidizer. The liquid portion of the vehicle allows for a Liquid Injection Thrust Vector Controller (LITVC) as well as hypergolic propellant additives for ignition. The vehicle was designed to deliver approximately 0.31kg of Martian geological samples to a circular orbit at Mars of 343km at a 25o inclination. Although hybrid propulsion in general has been used on launch vehicles in the past, the integrated vehicle subsystems that operate in conjunction with these propulsion elements do not typically operate in a Martian environment, which in this application can get as cold as -40oC. The PAA advanced the maturity of these subsystems by performing detailed design and analysis on the vehicle with respect to structures and mechanisms, Guidance/Navigation/Control (GNC) systems, avionics, Reaction Control System (RCS), LITVC, thermal environments, and advanced Computational Fluid Dynamics (CFD). This paper will summarize the results of these studies.

Yaghoubi, Darius↗
DOE OSTI2025

RT-EZ: A Golden Gate Assembly Toolkit for Streamlined Genetic Engineering of Rhodotorula toruloides

For economic and sustainable biomanufacturing, the oleaginous yeast Rhodotorula toruloides has emerged as a promising platform for producing biofuels, pharmaceuticals, and other valuable chemicals. However, genetic manipulation of R. toruloides has been limited by its high GC content and the lack of a replicating plasmid, necessitating gene integration into the genome of the yeast. To address these challenges, we developed the RT-EZ (R. toruloides Efficient Zipper) toolkit, a versatile tool based on Golden Gate assembly, designed to streamline R. toruloides engineering with improved efficiency and flexibility. The RT-EZ toolkit simplifies vector construction by incorporating new features such as bidirectional promoters and 2A peptides, color-based screening using RFP, and sequences optimized for both Agrobacterium tumefaciens-mediated transformation (ATMT) and easy linearization, enabling straightforward selection and transformation. Notably, the RT-EZ kit can be used to construct an expression cassette with four different genes in one assembly reaction, significantly improving vector construction speed and efficiency. The utility of the RT-EZ toolkit was demonstrated through the successful synthesis of arachidonic acid in R. toruloides by coexpressing fatty acid elongases and desaturases. Furthermore, this result underscores the potential of the RT-EZ toolkit to advance synthetic biology in R. toruloides, providing a streamlined method for addressing genetic engineering challenges in the yeast.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Atomic Force Microscopy to Characterize Antimicrobial Peptide-Induced Defects in Model Supported Lipid Bilayers

Antimicrobial peptides (AMPs) interact with bacterial cell membranes through a variety of mechanisms, causing changes extending from nanopore formation to microscale membrane lysis, eventually leading to cell death. Several AMPs also disrupt mammalian cell membranes, despite their significantly different lipid composition and such collateral hemolytic damage hinders the potential therapeutic applicability of the AMP as an anti-microbial. Elucidating the mechanisms underlying the AMP–membrane interactions is challenging due to the variations in the chemical and structural features of the AMPs, the complex compositional variations of cell membranes and the inadequacy of any single experimental technique to comprehensively probe them. (1) Background: Atomic Force Microscopy (AFM) imaging can be used in combination with other techniques to help understand how AMPs alter the orientation and structural organization of the molecules within cell membranes exposed to AMPs. The structure, size, net charge, hydrophobicity and amphipathicity of the AMPs affect how they interact with cell membranes of differing lipid compositions. (2) Methods: Our study examined two different types of AMPs, a 20-amino acid, neutral, α-helical (amphipathic) peptide, alamethicin, and a 13-amino acid, non-α-helical cationic peptide, indolicidin (which intramolecularly folds, creating a hydrophobic core), for their interactions with supported lipid bilayers (SLBs). Robust SLB model membranes on quartz supports, incorporating predominantly anionic lipids representative of bacterial cells, are currently not available and remain to be developed. Therefore, the SLBs of zwitterionic egg phosphatidylcholine (PC), which represents the composition of a mammalian cell membrane, was utilized as the model membrane. This also allows for a comparison with the results obtained from the Quartz Crystal Microbalance with Dissipation (QCM-D) experiments conducted for these peptides interacting with the same zwitterionic SLBs. Further, in the case of alamethicin, because of its neutrality, the lipid charge may be less relevant for understanding its membrane interactions. (3) Results: Using AFM imaging and roughness analysis, we found that alamethicin produced large, unstable defects in the membrane at 5 µM concentrations, and completely removed the bilayer at 10 µM. Indolicidin produced smaller holes in the bilayer at 5 and 10 µM, although they were able to fill in over time. The root-mean-square (RMS) roughness values for the images showed that the surface roughness caused by visible defects peaked after peptide injection and gradually decreased over time. (4) Conclusions: AFM is useful for helping to uncover the dynamic interactions between different AMPs and cell membranes, which can facilitate the selection and design of more efficient AMPs for use in therapeutics and antimicrobial applications.

Swana, Kathleen W.↗
NASA NTRSDate not supplied

Distributed Spacecraft Autonomy - Development of Swarm Autonomy Capability and Scalability for Spacecraft

The Distributed Spacecraft Autonomy project is developing a suite of software tools that enable an operator to command and receive data from a swarm as a single entity, enable a swarm to autonomously coordinate its actions via distributed decision making and reactive closed-loop control, and model swarm behavior in the presence of anomalies or failures. Our use case is the mapping of the electron density of the ionosphere using radio tomography by coordinating the selection of appropriate GPS channels, and by recording Total Electron Count (TEC) measurements. DSA will be demonstrated onboard the NASA Ames Starling mission – a swarm of four small, LEO spacecraft, scheduled to launch in 2021. We will also perform a ground demonstration with simulated and hardware-in-the-loop elements, to validate the tools for controlling swarms of up to 100 assets. The capability to communicate autonomously between the swarm satellites is demonstrated via a sophisticated simulation architecture. Historical Plasmasphere TEC data obtained via dual-band Novatel GPS Receivers are utilized as a representative input dataset for the swarm. The representative TEC data and GPS satellite observability information is fed to the autonomous software package in place of a true real-time ground data collection process. The swarm satellites actively share status updates amongst one another and utilize multi-agent decision making to optimally identify regions of interest in the TEC distribution. The software, aware of the bandwidth limitations of the swarm satellites, prioritizes explorative measurements, which define the range of observability for the satellites, as well as exploitative measurements, which focus on maximizing the observance potential of regions with prolonged, elevated TEC density. The science of this study can ultimately be used to determine the dynamics and coupling of Earth’s magnetosphere, ionosphere, and atmosphere and their response to solar and terrestrial inputs. The findings can be applied to the imaging of critical, transient phenomena in the magnetosphere in later missions. Meanwhile, the swarm autonomy capabilities have far reaching potential in future satellite missions. As an experimental demonstration of the autonomous capabilities of the network, a message is first printed within a core Flight Executive (cFE) application. Two cFE applications that communicate with one another within the same core Flight System (cFS) are shown. Communication between mission applications on the internal cFE bus is extended to utilize Data Distribution Service (DDS) for vehicle-to-vehicle networking. The DDS middleware provides reliable delivery, routing, and topic subscription features over User Datagram Protocol (UDP). Leveraging Linux containerization, a networked set of satellite instances are generated by script to simulate swarm behavior. Swarm commanding and synchronization through the network is demonstrated under various topologies and data-loss conditions. Finally, autonomous swarm scalability from 2 satellites to 100 satellites is shown.

Distributed Autonomy↗
NASA NTRS2020

Distributed Spacecraft Autonomy (DSA): Development of Swarm Autonomy Capability and Scalability for Spacecraft

The Distributed Spacecraft Autonomy project is developing a suite of software tools that enable an operator to command and receive data from a swarm as a single entity, enable a swarm to autonomously coordinate its actions via distributed decision making and reactive closed-loop control, and model swarm behavior in the presence of anomalies or failures. Our use case is the mapping of the electron density of the ionosphere using radio tomography by coordinating the selection of appropriate GPS channels, and by recording Total Electron Count (TEC)measurements. DSA will be demonstrated on board the NASA Ames Starling mission a swarm of four small, LEO spacecraft, scheduled to launch in 2021. We will also perform a ground demonstration with simulated and hardware-in-the-loop elements, to validate the tools for controlling swarms of up to 100 assets.The capability to communicate autonomously between the swarm satellites is demonstrated via a sophisticated simulation architecture. Historical Plasma sphere TEC data obtained via dual-band Novatel GPS Receivers are utilized as a representative input data set for the swarm. The representative TEC data and GPS satellite observability information is fed to the autonomous software package in place of a true real-time ground data collection process. The swarm satellites actively share status updates amongst one another and utilize multi-agent decision making to optimally identify regions of interest in the TEC distribution. The software,aware of the bandwidth limitations of the swarm satellites, prioritizes explorative measurements,which define the range of observability for the satellites, as well as exploitative measurements,which focus on maximizing the observance potential of regions with prolonged, elevated TEC density. The science of this study can ultimately be used to determine the dynamics and coupling of Earth's magnetosphere, ionosphere, and atmosphere and their response to solar and terrestrial inputs. The findings can be applied to the imaging of critical, transient phenomena in the magnetosphere in later missions. Meanwhile, the swarm autonomy capabilities have far reaching potential in future satellite missions.As an experimental demonstration of the autonomous capabilities of the network, a message is first printed within a core Flight Executive (cFE) application. Two cFE applications that communicate with one another within the same core Flight System (cFS) are shown.Communication between mission applications on the internal cFE bus is extended to utilize Data Distribution Service (DDS) for vehicle-to-vehicle networking. The DDS middle ware provides reliable delivery, routing, and topic subscription features over User Data gram Protocol (UDP).Leveraging Linux containerization, a networked set of satellite instances are generated by script to simulate swarm behavior. Swarm commanding and synchronization through the network is demonstrated under various topologies and data-loss conditions. Finally, autonomous swarms calability from 2 satellites to 100 satellites is shown.

Fugate, Jason↗
DOE OSTI2024

First-Principles Simulation of Beam-Induced Processes Underlying Atomic Manipulation in Electron Microscopes

The development of experimental methods and apparatuses capable of promoting atomically precise material manipulations holds great promise for realizing the ultimate limit of feature miniaturization in materials and devices. The ability to modify materials atom by atom is anticipated to usher in new technologies in areas as diverse as separation science, medicine, and quantum information science. Historically, scanning probe-based techniques have been the most prominent approaches in this space. However, these methods are best suited for the manipulation of surface-exposed regions of materials, as the strong perturbations required for bond scission are delivered most effectively to atoms in the near-proximity to the scanning probe. In contrast, convergent electron beams with energies tuned slightly below the threshold for inducing irreversible knock-on damage have recently been employed (within scanning transmission electron microscopy) to promote atomic-scale bond rearrangements in various beam-stable solids. Currently, however, the efficiency and selectivity of beam-induced atomic manipulation processes with focused electron beams are such that long irradiation times are required to induce a desired atomic rearrangement. With a better understanding of the underlying physics dictating the outcome of a given irradiation event, methods can be devised to improve the efficiency of these techniques so that their promise can be fully realized through widespread adoption.To this end, this Account details our recent efforts to develop and apply tractable first-principles simulation approaches for studying the response of materials to electric beam-like external electric potentials applied in real space. We briefly review the concepts and capabilities in the area of atomically precise materials manipulation and review the early demonstrations of accomplishments in this area, focusing on studies using scanned convergent electron beam probes in particular. We expound upon the depth of the challenge and identify critical shortcomings of theoretical methods that have previously been employed in the simulation of beam-induced processes. We then describe the computational methods that we have generalized from the concepts and tools most commonly applied to the study of molecular photochemistry and how our adaptations of these methods can be employed to capture the relevant dynamical phenomena for beam-induced processes ranging from the initial electron scattering to the ensuing multistate reactions. Here, we contextualize these methods within the current state of the art in this area, which has historically focused primarily on the simulation of inelastic image formation in the electron microscope for the purpose of interpreting the results of quantitative electron microscopy experiments. We demonstrate that the spatial distribution of state-specific excitation rates due to the presence of an external (probe) electric charge is inhomogeneous, such that irradiation at particular locations in materials can favor specific electronic transitions (and disallow others). In addition to the potential for excited-state reaction pathways to be accessed through the initial inelastic scattering of the tightly focused electron beam from the targeted atoms, we also identify favorable conditions for the electronically nonadiabatic evolution of the highly vibrationally excited system to open complex multistate reaction pathways. Implications of the early results for understanding the mechanisms and potential routes to improved efficiency and selectivity in beam-induced reactions are discussed. We conclude with a summary of the current state of theory and modeling capabilities in this area and provide our perspective on future directions for theoretical and experimental developments that we view as crucial to advancing the use of convergent electron beams in mode-specific, atomically precise platforms for direct-write materials modifications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Hydrologic Model Data for the East Fork Poplar Creek Watershed Simulated with the Advanced Terrestrial Simulator (ATS): Streamflow and Network Expansion–Contraction Dynamics

This dataset supports hydrologic modeling and stream network expansion–contraction analysis for the East Fork Poplar Creek (EFPC) Watershed in Tennessee. It includes a Jupyter notebook for model setup, model configuration files, simulation outputs, and derived products used to evaluate model performance and investigate stream dynamics under varying hydrologic conditions. The dataset was generated using the Watershed Workflow Python package and the Advanced Terrestrial Simulator (ATS), enabling integrated surface–subsurface hydrologic simulations using a stream-aligned mesh. Outputs include high-resolution time series of streamflow, active network length, water table depth, and related hydrologic variables. Also included are spatially explicit stream persistency indices and classifications of reaches as perennial or non-perennial. These data facilitate reproducibility and support further research on stream intermittency and variability in network extent.The model data archive is organized in following directories:1) model_setup_inputsContains the Watershed Workflow Jupyter notebooks (accessed through any open source code editor), selected input datasets, and resulting ATS input files, including XML files (access through any open source code editor), computational mesh (.exo files can be viewed using Paraview), and meteorological forcing files (.h5 files can be accessed through h5py python package and HDFView open source software). 2) model_outputsIncludes ATS simulation outputs relevant to this study. Time series of spatially integrated or averaged variables (e.g., streamflow, water table depth) are provided as CSV files. Select spatial fields (e.g., ponded depth and water table depth) are saved as pickled Python objects to reduce file size, and can be accessed through pickle package in Python. Key geometry objects from Watershed Workflow—such as the surface mesh and river tree—are also included to support analysis of streamflow persistency and expansion–contraction dynamics. These files can also be accessed through Watershed Workflow Python package.3) model_evaluationProvides observed streamflow time series and field survey-based flow regime classifications used to evaluate model performance. Jupyter notebooks for processing ATS outputs and comparing model predictions with observations to build confidence in the model prior to scientific analysis are also included.4) Q_L_relationshipsContains workflows for generating time series of discharge, active network length, and related hydrologic variables used in the stream network expansion–contraction analysis. Includes routines for delineating baseflow-dominated periods. For each catchment, notebooks and processed data (as pickled DataFrames accessed through Pandas Python package) are provided. 5) figure_scriptsProvides the Jupyter notebooks used to generate the figures presented in the paper.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Explaining and predicting human behavior and social dynamics in simulated virtual worlds: reproducibility, generalizability, and robustness of causal discovery methods

Ground Truth program was designed to evaluate social science modeling approaches using simulation test beds with ground truth intentionally and systematically embedded to understand and model complex Human Domain systems and their dynamics Lazer et al. (Science 369:1060–1062, 2020). Our multidisciplinary team of data scientists, statisticians, experts in Artificial Intelligence (AI) and visual analytics had a unique role on the program to investigate accuracy, reproducibility, generalizability, and robustness of the state-of-the-art (SOTA) causal structure learning approaches applied to fully observed and sampled simulated data across virtual worlds. In addition, we analyzed the feasibility of using machine learning models to predict future social behavior with and without causal knowledge explicitly embedded. In this paper, we first present our causal modeling approach to discover the causal structure of four virtual worlds produced by the simulation teams—Urban Life, Financial Governance, Disaster and Geopolitical Conflict. Our approach adapts the state-of-the-art causal discovery (including ensemble models), machine learning, data analytics, and visualization techniques to allow a human-machine team to reverse-engineer the true causal relations from sampled and fully observed data. We next present our reproducibility analysis of two research methods team’s performance using a range of causal discovery models applied to both sampled and fully observed data, and analyze their effectiveness and limitations. We further investigate the generalizability and robustness to sampling of the SOTA causal discovery approaches on additional simulated datasets with known ground truth. Our results reveal the limitations of existing causal modeling approaches when applied to large-scale, noisy, high-dimensional data with unobserved variables and unknown relationships between them. We show that the SOTA causal models explored in our experiments are not designed to take advantage from vasts amounts of data and have difficulty recovering ground truth when latent confounders are present; they do not generalize well across simulation scenarios and are not robust to sampling; they are vulnerable to data and modeling assumptions, and therefore, the results are hard to reproduce. Finally, when we outline lessons learned and provide recommendations to improve models for causal discovery and prediction of human social behavior from observational data, we highlight the importance of learning data to knowledge representations or transformations to improve causal discovery and describe the benefit of causal feature selection for predictive and prescriptive modeling.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

Emerging Electrochemical Techniques for Probing Site Behavior in Single-Atom Electrocatalysts

Single-atom catalysts (SACs) have aroused tremendous interest over the past decade, particularly in the community of energy and environment-related electrocatalysis. A rapidly growing number of recent publications have recognized it as a promising candidate with maximum atomic utilization, distinct activity, and selectivity in comparison to bulk catalysts and nanocatalysts. However, the complexity of localized coordination environments and the dispersion of isolated sites lead to significant difficulties when it comes to gaining insight into the intrinsic behavior of electrocatalytic reactions. Furthermore, the low metal loadings of most SACs make conventional ensemble measurements less likely to be accurate on the subnanoscale. Thus, it remains challenging to probe the activity and properties of individual atomic sites by available commercial instruments and analytical methods. In spite of this, continuing efforts have lately focused on the development of advanced measurement methodologies, which are very useful to the fundamental understanding of SACs. There have recently been a number of in situ/operando techniques applied to SACs, such as electron microscopy, spectroscopy, and other analysis methods, which support relevant functions to identify the active sites and reaction intermediates and to investigate the dynamic behavior of localized structures of the catalytic sites. This Account aims to present recent electrochemical probing techniques which can be used to identify single-atomic catalytic sites within solid supports. First, we describe the basic principles of molecular probe methods for the study and analysis of electrocatalytic site behavior. In particular, the in situ probing technique enabled by surface interrogation scanning electrochemical microscopy (SISECM) can measure the active site density and kinetic rate with high resolution. An alternative electrochemical probing technique is further demonstrated on the basis of single-entity electrochemistry, which allows the unique electrochemical imaging of the size and catalytic rate of single atoms, molecules, and clusters. Next, the merits and limitations of different electrochemical techniques are then discussed, along with perspectives for future prospects. Apart from this, we further showcase the powerful capability of emerging electrochemical probing techniques for determining significant effects and properties of SACs for various electrocatalytic reactions, including oxygen reduction and evolution, hydrogen evolution, and nitrate reduction. Overall, electrochemical techniques with atomic resolution have greatly increased opportunities for observing, measuring, and understanding the surface and interface chemistry during energy conversion. In the future, it is anticipated that the development of electrochemical probing techniques will be advanced with innovative perspectives on the behavior and features of SACs. We hope that this Account can contribute in several ways to promoting the fundamental knowledge and technical progress of emerging electrochemical measurements for studying SACs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRSDate not supplied

Assessing the Effects of Various Surface Textures and Features on Turbulent Heat Transfer in Hypersonic Flight

Experiments were conducted in the NASA Ames Hypervelocity Free Flight Aerodynamic Facility (ballistic range) to quantify the effects on turbulent convective heat transfer of distributed surface roughness, and of isolated features, representative of thermal protection systems on atmospheric entry vehicles. The surface textures and features were applied on the conic frusta of 45o sphere-cone models having a nose-to-base radius ratio of 0.5, similar to the forebody geometry of the Galileo and Pioneer-Venus entry probes. Test conditions were selected to provide turbulent roughness Reynolds numbers, k+, in the ranges expected for outer planet entry missions. Turbulent flow on the conic frustum was achieved by tripping the flow on the sphere-segment nose cap with distributed surface roughness, created by sand-blasting the nose cap. Surface textures included distributed, acreage, roughness, as well as cavity and groove discrete features. The majority of the data to be presented are results for distributed roughness, which includes both random, sand-grain-like roughness, and regular pattern roughness. The pattern roughness was designed to represent the roughness on woven thermal protection system materials, such as NASA’s 3-D Medium Density Carbon Phenolic (3MDCP), also known as HEEET, developed by the Heatshield for Extreme Entry Environments Technology project. The pattern roughness tested is a 3-D wavy surface, and includes three different roughness element height-to-spacing ratios representative of two configurations of 3MDCP, and spanning ratios measured both before, and after, ablation in an arc jet test facility. The patterns tested in the ballistic range were laser-etched on metal models, and represented an idealized version of the real-world materials in which each roughness element was nearly identical. Additional tests were performed wherein the laser-etched patterns were degraded by sand-blasting with various sized grit media, to produce regular patterns with superimposed irregular roughness, more representative of flight materials. Results of each will be compared. The discrete features tested included cylindrical cavities and rectangular grooves of various width-to-depth ratios. Cavities represent either heatshield damage, such as from micro-meteoroid and orbital debris (MMOD) damage, or from designed penetrations, such as on the Genesis sample return capsule. The grooves were scaled representations of seams between segments of HEEET material in a notional tiled thermal protection system. The tests examined the effects on turbulent heating downstream of the isolated features. The tests were conducted at speeds between 3 km/s and 4 km/s in air between 0.15 atm and 0.25 atm (Mach numbers between 9 and 12). Roughness Reynolds numbers, k+, ranged from 12 to 70 for the sand roughness, and as high as 200 for the pattern roughness. Boundary-layer parameters required for calculating k+ were evaluated using computational fluid dynamics simulations using the DPLR (Data Parallel Line Relaxation) code. Each model included both rough- and smooth-wall segments, and heat transfer augmentation factors were determined as the ratio of the rough-wall to smooth-wall heat flux measured on each test.

hypersonic↗
DOE OSTI2024

Solid State Quantum Refrigeration Superconducting, Absorption and Measurement Based (Final Technical Report)

During this DOE grant, DE-SC0017890, in place for the past six years, all proposed research was carried out and published in peer-reviewed papers, as well as other projects that emerged during the research. In that effort the research team accomplished all proposed research, as well as many closely related research projects discovered and conceived of during the grant. These works included “Efficient Quantum Measurement Engines”, a work published in Physical Review Letters, giving a theory of quantum measurement-based engines, which uses quantum measurement as a resource. These engines are designed to efficiently convert energy from the stochastic quantum measurement process into useful work. Further publications include “Experimental Realization of a Quantum Dot Energy Harvester”, a joint theory and experimental work in collaboration with the group of Charles Smith in Cambridge, UK, as well as long time theoretical collaborators, Rafael Sánchez and Björn Sothmann. This work, featured as an Editor’s Suggestion in Physical Review Letters, realized an earlier theoretical proposal of ours, whereby two resonant tunneling quantum dots are connected to a central electronic cavity that is heated by a hot energy source. We also published “Superconducting Quantum Refrigerator: Breaking and Rejoining Cooper Pairs with Magnetic Field Cycles” a work done in collaboration with experimentalist Francesco Giazotto from ENS Pisa, Italy, which also resulted in a patent. This paper, published in Phys. Rev. Applied, advanced the concept of a cyclic fridge based on the normal/superconducting phase transition together with layered materials separated by tunnel junctions. We also completed the proposed research on a heat transistor, publishing “Thermal transistor and thermometer based on Coulomb-coupled conductors”, carried out as a collaboration between my group and theorists Splettstoesser (Lund U., Sweden), Sothmann (U. Duisburg-Essen, Germany), and Sánchez (U. Autónoma de Madrid, Spain). We carried out an analysis of a quantum coupled to a quantum point contact as a sensitive thermometer and heat transistor. We found the optimal statistical estimator for the temperature and compared it with experiments on the same type of devices. We also investigated autonomous quantum absorption refrigerators using quantum dots to cool by using a very hot thermal reservoir to drive heat between two other reservoirs. In the article “Quantifying the quantum heat contribution from a driven superconducting circuit”, we demonstrated that for a driven superconducting circuit, we showed heat flow provided by a hot source to the qubit can be switched on and off by varying external parameters, the frequency and the intensity of the driving. In the work “Stochastic thermodynamic cycles of a mesoscopic thermoelectric engine”, we reconsidered the autonomous thermoelectric heat engine in terms of underlying cycles. Rather than periodic behavior, the cycles were stochastic in nature. Nevertheless, by undertaking a graph theoretical analysis of the elementary transport processed, great quantitative and qualitative insight could be found. We also considered the quantum measurement process and showed that a quantum version of Maxwell’s demon could be related to the work extraction of a quantum system, closely related to arrow-of-time measures for quantum measurement, as described in our article “Thermodynamics of quantum measurement and Maxwell's demon's arrow of time”. This work was selected in Phys. Rev. A as an Editor’s Suggestion. A recent preprint titled “Cyclic Superconducting Quantum Refrigerators Using Guided Fluxon Propagation” accomplished an important piece of this grant: to propose a new kind of quantum refrigerator using the dynamics of fluxons in a type II superconductor. This invention envisioned a race-track type geometry where fluxons are confined. By applying a gradient of magnetic field together with electric current in a Corbino geometry, the circulating fluxons can actively cool a cold reservoir, realizing a new type of cyclic superconducting refrigerator. We also investigated the possibility of thermal control from different points of view. The application of quantum measurement to the system gives a new kind of control on the system of interest – we have pioneered this approach and shown that measurement can boost the thermal power of quantum engines as described in “Continuous measurement boosted adiabatic quantum thermal machines”. The ability to have heat flows on demand is an outstanding challenge, and we have provided new solutions to this problem in Thermal control across a chain of electronic nanocavities” for a chain of electron cavities using gating voltage control. The control methods using qubit/qubit coupling to create absorption fridges at their most fundamental level have also been developed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

TRANSENSOR: Transformer Real-time Assessment INtelligent System with Embedded Network of Sensors and Optical Readout. Final Report

Utilities across the world are wrestling with evolving market dynamics, population growth and climate change. Distributed Energy Resources (DERs) such as solar photovoltaics, distributed generators and energy storage systems are becoming important parts of the U.S. energy mix. These factors are driving an increasing need for low-cost grid asset monitoring. Aside from being costly, traditional utility monitoring systems are not sufficiently robust and do not provide real-time visibility into the condition of grid assets such as transformers. Lack of accurate real-time measurements on performance has resulted in the use of lagging indicators, such as oil sample analysis. To address this need, an innovative embedded optical sensing technology, Transformer Real-time Assessment Intelligent System (TRANSENSOR) was developed, validated and demonstrated in this project. To date, TRANSENSOR has focused on transformers but is extendable to other grid assets. In addition to the technology being embedded into new transformers during manufacturing, a retrofit configuration that can be installed on existing transformers in the field was also developed. It is anticipated that the ability to retrofit existing transformers will help accelerate adoption of the underlying TRANSENSOR technology. Phase 1 of the project focused on laboratory development and qualification of the technology. Following iterations and exploration of relevant optical sensing modalities and multiplexed configurations of interest for the transformer environment, an effective candidate configuration was agreed upon, down-selected and custom-designed for embedding into General Electric (GE) network transformers. Two new GE 500 kilovolt ampere (kVA), 27 kilovolt (kV) distribution network transformers were built with embedded fiber-optic (FO) sensors and successfully qualified per industry standards at GE’s Shreveport, Louisiana facility during Phase 1 of the project. Following the successful completion of Phase 1, the team proceeded to Phase 2, which focused on a field demonstration of the technology. Over Phase 2, the first new GE transformer built with embedded fiber-optic sensors was installed in an above-ground cage and connected to the grid at Con Edison’s Astoria facility. A second transformer equipped with TRANSENSOR was installed in an underground vault. Additionally, an older (1982 year model) GE transformer in an above-ground cage was retrofitted with fiber- optic sensors and reconnected to the grid at ConEd’s facility. Analysis of data acquired from the sensors showed interesting correlations with transformer loading. Additionally, key events such as transformer low-voltage network connection, primary-side energizing, and a pressure loss event from an oil sampling were detected by the TRANSENSOR system. Online data processing/feature extraction algorithms for the second transformer in the underground vault detected key features and event alerts that were transmitted through a wireless 4G connection. The remote deployment concept showed promising results with data collection running for a total of 8 months across the three (3) GE transformers instrumented for the Phase 2 field demonstration. This sets the stage well for further development and commercialization.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2025

A New Measurement of the Neutron Electric Form Factor with the Super Bigbite Spectrometer Apparatus

Protons and neutrons, collectively known as nucleons, make up the nuclei at the core of atoms which form our world. The nucleon has been under intensive study for over 100 years, and yet we still do not fully understand the internal dynamics which govern properties like its spin or its mass-which contributes to almost all of the visible mass in the universe. These dynamics are governed by quantum chromodynamics(QCD), the predictions of which are experimentally tested at high energy accelerator facilities such as Jefferson Lab. TheGEN-II experiment (E12-09-016) is one such experiment. GEN-II is part of the Super Bigbite Spectrometer (SBS) experimental form factor pro gramme taking place in Hall A at Jefferson Lab, which aims to make precision measurements of the nucleon electromagnetic form factors(EMFFs)at record high values of squared four momentum transfer ¿2. EMFFs describe the electric and magnetic moment distributions within the nucleon. They can be measured through elastic electron scattering off the nucleon, and describe the recoil response of the target nucleon at a given energy scale. GEN-II is a double polarized semi-exclusive beam target asymmetry (BTA) experiment, seeking to measure the electric form factor of the neutron,¿¿ ¿,at three new values of squared four-momentum transfer¿2 =2.92,6.74and9.82GeV². The latter two points being at record high ¿2. The form factor is determined through measuring the BTA of quasielliptical scattering of a neutron from a polarized nuclear target. The experiment utilized the CEBAF accelerator to produce longitudinally polarized electrons up to ~85% polarization, which were scattered off neutrons within a novel polarized helium-3 (³He) target. This new polarized ³He target was employed by building on the technology of its precursors which existed in similar preceding experiments. This target was designed to operate at the high luminosities typical of Hall A, and reached a record breaking combination of polarization and beam intensity known as figure of merit, three times larger than those predecessors. The SBS collaboration designed and constructed two brand new high acceptance spectrometers for these experiments, an electron arm named Bigbite (BB) and a hadron arm named Super Bigbite. Both spectrometers featured a large acceptance EM dipole magnet, and complementary detector systems. The electron arm contained gaseous electronmultipliers(GEMs) which were used for high precision tracking of the scattered electrons, a heavy gas cherenkov (GRINCH) which was used for PID between electrons and pions, a plastic i ii scintillator timing hodoscope to provide high resolution timing of the start of events, and a pair of EM calorimeters (BBCal) which provided energy measurements of detected particles, and provided the experimental trigger. The hadron arm also contained a system of GEMs which will be utilized for future SBS experiments, and a hadron calorimeter designed to provide position, timing and energy measurements of the recoiling nucleon. The calibration of all detector subsystems, beam and target data is discussed, with a focus on novel timing calibrations to the hodoscope and hadron calorimeter. An analysis of selecting quasielliptical events and suppressing background contributions from a number of sources which contaminate the final event sample is given. The largest irreducible backgrounds are found to be from misidentified protons, timing accidentals and inelastic events. The physical asymmetry is measured and used to extract a value for the form factor ratio ¿¿ ¿/¿¿ ¿. High precision ¿2 data for ¿¿ ¿ is used to then extract ¿¿ ¿. This work finds at ¿2 = 2.92 GeV2 that ¿¿ ¿ = 0.0129+0.0019 -0.0020. This result is in statistical agreement with existing fits to world data, and predictions from the constituent quark model and Dyson–Schwinger equations, in this region of ¿2.

Penman, Gary [Univ. of Glasgow, Scotland (United K↗
DOE OSTI2023

Measuring the giant radio galaxy length distribution with the LoTSS

Many massive galaxies launch jets from the accretion disk of their central black hole, but only ~10 3 instances are known in which the associated outflows form giant radio galaxies (GRGs, or giants): luminous structures of megaparsec extent that consist of atomic nuclei, relativistic electrons, and magnetic fields. Large samples are imperative to understanding the enigmatic growth of giants, and recent systematic searches in homogeneous surveys constitute a promising development. For the first time, it is possible to perform meaningful precision statistics with GRG lengths, but a framework to do so is missing. We measured the intrinsic GRG length distribution by combining a novel statistical framework with a LOFAR Two-metre Sky Survey (LoTSS) sample of freshly discovered giants. In turn, this allowed us to answer an array of questions on giants. For example, we can now assess how rare a 5 Mpc giant is compared with one of 1 Mpc, and how much larger – given a projected length – the corresponding intrinsic length is expected to be. Notably, we can now also infer the GRG number density in the Local Universe. We assumed the intrinsic GRG length distribution to be Paretian (i.e. of power-law form) with tail index ξ, and predicted the observed distribution by modelling projection and selection effects. To infer ξ, we also systematically searched the LoTSS for hitherto unknown giants and compiled the largest catalogue of giants to date. We show that if intrinsic GRG lengths are Pareto distributed with index ξ, then projected GRG lengths are also Pareto distributed with index ξ. Selection effects induce curvature in the observed projected GRG length distribution: angular length selection flattens it towards the lower end, while surface brightness selection steepens it towards the higher end. We explicitly derived a GRG’s posterior over intrinsic lengths given its projected length, laying bare the ξ dependence. We also discovered 2060 giants within LoTSS DR2 pipeline products; our sample more than doubles the known population. Spectacular discoveries include the largest, second-largest, and fourth-largest GRG known (l p = 5.1 Mpc, l p = 5.0 Mpc, and l p = 4.8 Mpc), the largest GRG known hosted by a spiral galaxy (l p = 2.5 Mpc), and the largest secure GRG known beyond redshift 1 (l p = 3.9 Mpc). We increase the number of known giants whose angular length exceeds that of the Moon from 10 to 23; among the discoveries is the angularly largest known radio galaxy in the Northern Sky, which is also the angularly largest known GRG ($\phi$ = 2°). Combining theory and data, we determined that intrinsic GRG lengths are well described by a Pareto distribution, and measured the index ξ = –3.5 ± 0.5. This implies that, given its projected length, a GRG’s intrinsic length is expected to be just 15% larger. Finally, we determined the comoving number density of giants in the Local Universe to be n GRG = 5 ± 2(100 Mpc) –3 . We developed a practical mathematical framework that elucidates the statistics of giant radio galaxy lengths. Through a LoTSS search, we also discovered 2060 new giants. By combining both advances, we determined that intrinsic GRG lengths are well described by a Pareto distribution with index ξ = –3.5 ± 0.5, and that giants are truly rare in a cosmological sense: most clusters and filaments of the Cosmic Web are not currently home to a giant. Thus, our work yields new observational constraints for analytical models and simulations featuring radio galaxy growth.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

Build Orientation Dependent Microstructure in Polymer Laser Sintering: Relationship to Part Performance and Evolution with Aging

Laser sintering (LS) is widely used to produce functional polymeric parts; however, the resulting parts are often limited by their porous structure, and performance of the part may be strongly anisotropic. Relating the structural features of parts to build process conditions or powder feedstock has been explored previously. In contrast, little is known regarding how the unique internal structures of LS parts evolve and relate to their performance later in their life cycle, for example, after use in a real-world operating environment. In this study, a tightly controlled LS build process and measurement campaign by standard X-ray computed tomography (XCT), supported by high-resolution synchrotron XCT, was used to benchmark the internal microstructure (e.g. porosity) as a function of four different build orientations in printed polyamide-12 (PA-12) parts. The initial performance of the parts after printing was characterized by tensile testing and dynamic mechanical analysis (DMA). Arrays of PA-12 parts in different build orientations were exposed to steam (under pressure) and air across multiple temperature and time points for the purposes of accelerated aging through oxidative and hydrolytic breakdown. Exposing parts to steam dramatically altered the internal microstructure and functional properties such as the glass transition temperature, tensile properties, and damping behavior. Notably, post-aging XCT revealed large microstructural changes after only 40 h of steam treatment relative to the as-printed specimens. Furthermore, pore reorganization and changes in crystallinity occurred regardless of whether the steam temperature was aggressive enough to induce a significant loss in mechanical properties. The build orientation dependence on the aging rate was minimal with the relative trend in performance persisting across most metrics among the different orientations even after aging.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Advanced Computational Modeling of High-Level Waste Vitrification at the Hanford Site

The U.S. Department of Energy (DOE) has selected vitrification for stabilizing legacy tank waste at the Hanford site, where radioactive waste from plutonium production was historically stored in underground tanks. This waste will be separated into low-activity waste (LAW) and high-level waste (HLW) fractions and processed at the Waste Treatment and Immobilization Plant (WTP). At WTP, glass melters are used for the vitrification of radioactive tank waste, transforming it into a stable borosilicate glass form for safe long-term storage. The melter vessel is constructed from highly durable and heat-resistant materials, where the vitrification process occurs. The main regions that are modeled are the melt pool, plenum, cold cap, riser/discharge chamber, and surrounding structure with insulation layers. Forced convection induced by air bubblers at the base of the melter ensure uniform temperature distribution and provide heat to the cold cap layer. The cold cap is a region of reacting batch feed that floats on top of the molten glass and is where the batch-to-glass reactions occur. Joule heating provided by electrodes mounted along the vertical walls of the melter and immersed directly in the glass, generates the necessary heat for the net endothermic conversion processes that occur in the cold cap. The high temperatures, radioactivity, and opaque nature of the glass prevent direct observation inside the melters. Therefore, computational models are essential for providing insight into factors that affect melter throughput. Thermocouples in the plenum provide operators with plenum temperature measurements. Operational adjustments include bubbling rate, voltage supplied to the electrodes, feed adjustments, and glass removal rate. Different computational fluid dynamics (CFD) models have been developed, each serving a specific purpose. There are CFD models of different scale melters, as well as models that capture the two-phase flow interfaces of rising bubbles in the molten glass or models with a simplified molten glass region so that the surrounding structure and plenum can be feasibly incorporated. Pilot-scale melter models have been developed to serve as validation of the methods employed in the simulation of the full-scale WTP melters. Models incorporating resolved bubbling are used to develop momentum source terms to implement into a single phase, multi-region, steady-state flow model that is being validated by measured process parameters such as glass production rate, voltage, input power, plenum temperatures, etc. The resolved bubbling model uses the multiphase volume of fluid approach to model the system with a high-resolution interface capturing scheme to maintain sharp interfaces between the molten glass and the air phase. The suite of CFD models is continually being improved to incorporate more realistic physics and achieve faster turnaround time. For example, an incremental controller is implemented to automatically adjust electrode voltage within the simulation to a molten glass set point temperature of 1150°C. Newer models feature improved meshes to ensure conformal meshes between regions and eliminate unnecessary mesh refinement in areas that are not of interest (such as boundary layers in offgas ports). Instead of explicitly modeling the structural, refractory, and insulation layers of the melter, a thermal resistance approach is used with published correlations used for boundary conditions. The development of robust and efficient CFD models will be instrumental in enabling the WTP to successfully fulfill its mission of safely stabilizing legacy nuclear waste.

12 - MGMT OF RADIOACTIVE AND NON-RADIOACTIVE WASTE↗
DOE OSTI2026

Rapid Evaluation Framework for the CMIP7 Assessment Fast Track

As Earth system models (ESMs) grow in complexity and in volume of output data, there is an increasing need for rapid, comprehensive evaluation of their scientific performance. The upcoming Assessment Fast Track for the Seventh Phase of the Coupled Model Intercomparison Project (CMIP7) will require expeditious response for model analyses designed to inform and drive integrated Earth system assessments. To meet this challenge, the Rapid Evaluation Framework (REF), a community-driven platform for benchmarking and performance assessment of ESMs, was designed and developed. The initial implementation of the REF, constructed to meet the near-term needs of the CMIP7 Assessment Fast Track, builds upon four disparate community evaluation and benchmarking tools that are coupled together using the Coordinated Model Evaluation Capabilities (CMEC) framework. The REF runs within a containerized workflow for portability and reproducibility and is aimed at generating and organizing diagnostics covering a variety of model variables. The REF leverages well documented observational datasets to provide assessments of model fidelity across a collection of diagnostics. All diagnostics were identified and selected with community involvement and consultation. Operational integration with the Earth System Grid Federation (ESGF) will permit automated execution of the REF for selected diagnostics as soon as model output data are published on ESGF by the originating modeling centers. The REF is designed to be portable across a range of current computational platforms to facilitate use by modeling centers for assessing the evolution of model versions or gauging the relative performance of CMIP simulations before being published on ESGF. When integrated into production simulation workflows, results from the REF provide immediate quantitative feedback that allows model developers and scientists to quickly identify model biases and performance issues. After the REF is released to the community, its subsequent development and support will be prioritized by an international consortium of scientists and engineers, enabling a broader impact across Earth science disciplines. For instance, the REF will facilitate improvements to models and will enhance confidence in model projections through process-based selection of models based on their performance with respect to observations. Production of reproducible diagnostics and community-based assessments are key features of the REF. Furthermore, providing interoperability with existing evaluation packages assures that contributions from previous community efforts will be available for use in future model intercomparison projects.

Hoffman, Forrest [ORNL] (ORCID:0000000158024134)↗