Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Defect detection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Hydroxylation of Apollo 17 Soil Sample 78421 by Solar Wind Protons

Hydroxylation by solar wind protons has been simulated in our laboratory on Apollo 17 lunar sample 78421, a very mature regolith sample that is rich with agglutinates (68%). The goal of this study was to determine the rate of hydroxyl formation and their thermal stability by monitoring changes in the SiOH (hydroxyl) stretching band near 3 μm using diffuse reflectance FTIR spectroscopy (DRIFTS). A 2 keV H2+ ion beam was used to simulate proton implantation on 78421 and on a crushed fused silica sample. We find that the OH band does not change unless the samples have been annealed in vacuum prior to irradiation. Qualitatively, the OH bands for the fused silica and 78421 are very different. The OH band for fused silica is centered at 2.74 μm and is relatively sharp ranging from 2.67 - 3.1 μm at full-width-at-half-maximum (FWHM), while the OH band for 78421 is centered at 3.0 μm and ranges from 2.74 - 3.37 μm at FWHM. The increase in wavelength and broadened nature of the OH band in 78421 may be associated with the OH’s proximity to surface defects and/or lattice vacancies. The lack of the H2O bending mode at 6.1 μm indicates that any adsorbed terrestrial H2O is below our detection limit, and therefore the H2O stretching mode at 2.9 μm is not significantly contributing to the broad 3 μm OH band and implies that proton implantation by itself does not lead to water formation. To simulate the maximum dayside temperature on the lunar surface, the lunar sample was heated after proton irradiation. The proton induced OH concentration was reduced by as much as 25% after heating to 400 K (127 °C).

Apollo 17↗

Maintaining the Health of Software Monitors

Software health management (SWHM) techniques complement the rigorous verification and validation processes that are applied to safety-critical systems prior to their deployment. These techniques are used to monitor deployed software in its execution environment, serving as the last line of defense against the effects of a critical fault. SWHM monitors use information from the specification and implementation of the monitored software to detect violations, predict possible failures, and help the system recover from faults. Changes to the monitored software, such as adding new functionality or fixing defects, therefore, have the potential to impact the correctness of both the monitored software and the SWHM monitor. In this work, we describe how the results of a software change impact analysis technique, Directed Incremental Symbolic Execution (DiSE), can be applied to monitored software to identify the potential impact of the changes on the SWHM monitor software. The results of DiSE can then be used by other analysis techniques, e.g., testing, debugging, to help preserve and improve the integrity of the SWHM monitor as the monitored software evolves.

Runtime Monitor↗

Organic Matter in Itokawa Particles

The first Hayabusa mission returned samples from the near-Earth S-type asteroid 25143 Itokawa to Earth in 2010[1]. Although Itokawa has a lithology related to ordinary chondrites(OCs) that typically have low organic contents, several Itokawa particles were found to contain organic matter (OM)[2-5]. However, there was not an explicit conclusion to the origin of the observed OMin these early studies. We have extended our search for OM into other Itokawa grains. Here, we report extraterrestrial OM (macromolecular carbon and amino acids) observed in six Itokawa particles(including a category1 particle: RA-QD02-0162[#62; also nicknamed “Amazon”],and five category3 carbon-rich particles:RA-QD02-0012[#12], RA-QD02-0078[#78], RB-CV-0029[#29], RB-CV-0080 [#80] and RB-QD04-0052[#52]).All allocated Itokawa samples were initially analysed by spot and point-by-point mapping Raman spectroscopic analysis at the Open University, UK. Amazon was then transferred and mounted into indium on an aluminium stub, which was studied with a NanoSIMS 50L ion microprobe for its H,C,N isotopic compositions. The rest of the samples were mounted in sterile gold foils, and the amino acid contents of their acid hydrolysed hot water extracts were obtained with a liquid chromatography with tandem fluorescence and accurate mass detection at NASA Goddard Space Flight Center, USA. Based on the observation of the Raman parameters(e.g. the peak locations and widths of the defect (D) and graphite (G) bands)[6], a significant variety of carbonaceous materials has been observed in Amazon. The carbonaceous materials include primitive and unaltered OM that shares similarity with the IOM in primitive (CI,CM,CR) carbonaceous chondrites, as well as OM that has been heavily graphitised. The organic structure of the heated material is best represented by nanocrystalline graphite, comparable to that observed for metamorphosed meteorites (e.g., L3–6 Inman, Tieschitz and New Concord,CV3 Allende, and EH4 Indarch),suggesting peak metamorphic temperatures (PMT) of >~600°C. The thermal history recorded in the graphitic OM agrees with PMT estimates for returned Itokawa regolith grains (600–800°C)[7].We have obtained the H,C,N isotopic compositions for the primitive OM in Amazon, which exhibits unambiguously extraterrestrial isotopic signatures (δD = +4868±2288‰; δ13C = −24±5‰; δ15N = +344±20‰), contrasting to the typically negative isotopic values obtained for terrestrial organic matter[8]. The δD and δ13C values of the organic material in Amazon are comparable to OCs, however, the δ15N value is higher than that typically observed for OCs (δ15N = −47 to +36‰), and is similar to that of CRs (δ15N = +153 to +309‰)[9].Our data suggest a genetic link between the primitive organic material observed in Itokawa to CRs and IDPs for they share similar D, 13C and 15N enrichments[10].The high carbon contents of the five category 3 Itokawa particles suggest potentially higher OM abundances, hence we extracted and analysed amino acids in these samples. Although terrestrial contamination was observed primarily as L-protein amino acids, several terrestrially uncommon non-protein amino acids were also observed at low abundances, such as β-aminoisobutyric acid (β-AIB),β-amino-n-butyric acid (β-ABA), and β-alanine. Itokawa amino acid content observed here was dissimilar to thermally altered OCs, but preliminarily analogous to more aqueously altered CR2s.Continued evolution of Itokawa is evident by the in fall of primitive organic material derived from CRs/IDPs, accounting for a complex interplay between the remnant Itokawa silicates with exogenous organics. The results reported here are the first evidence of extraterrestrial OM in asteroid material from a sample-return mission, showcasing a working protocol for analysing samples returned by the Hayabusa2 and OSIRIS-REx missions

Q. H. S. Chan↗

Sensor-Failure Simulator

Outputs of defective sensors simulated for studies of reliability of control systems. Real-time sensor-failure simulator (SFS) designed and built for use with Advance Detection, Isolation, and Accommodation (ADIA) program. Equipment consists of IBM PC/XT computer and associated analog circuitry. User defines failure scenarios to determine which sensor signals fail and method(s) used to simulate failure.

Melcher, Kevin J.↗

Optical pattern recognition; Proceedings of the Meeting, Los Angeles, CA, Jan. 17, 18, 1989

Papers on optical pattern recognition are presented, covering topics such as the estimation of satellite pose and motion parameters using a neural net tracker, associative memory, optical implmentation of programmable neural networks, optoelectronic neural networks, dynamic autoassociative neural memory, heteroassociative memory, bilinear pattern recognition processors, optical processing of optical correlation plane data, and a synthetic discriminant function-based nonlinear optical correlator. Other topics include an interactive optical-digital image processor, geometric transformations for video compression and human teleoperator display, quasiconformal remapping for compensation of human visual field defects, hybrid vision for automated spacecraft landing, advanced symbolic and inference optical correlation filters, and a rotationally invariant holographic tracking system. Additional topics include the detection of rotational and scale-varying objects with a programmable joint transform correlator, a single spatial light modulator binary nonlinear optical correlator, optical joint transform correlation, linear phase coefficient composite filters, and binary phase-only filters.

Liu, Hua-Kuang↗

CST: A Tool for Optimizing the Efficiency and Effectiveness of Static-Code Analysis Tools

Static Code Analysis (SCA) is a vital component of NASA IV&V’s mission assurance for safety-critical software as it reduces the likelihood of software-induced hazards impacting mission success. Static Code Analysis achieves this by identifying hazards that may not have been otherwise detectable by typical code reviews or other testing. Using SCA tools, however, can be intimidating due to steep learning curves, especially considering tool performance and defect coverage varies greatly. Because of this variation amongst SCA tools, understanding which tools support certain defects and which do not, as well as understanding how to run an analysis based on steps that are unique to each tool, can be difficult to both new and experienced analysts alike. To mitigate this, the SCAWG or the IV&V Static Code Analysis Working Group, created the SCA Checker Taxonomy and Starting Point Profiles. The Checker Selection Tool (CST) incorporates these two SCAWG products into an interactive tool which allows the user to: select organized categories of defects they would like the SCA tools to discover, select default checkers depending on their mission type (e.g. flight), and configure multiple SCA tools at once. C/C++, Java, and Python defect checkers from four common SCA tools were utilized in this iteration of the CST. This iteration also includes the addition of training, SCA tool specific help, and taxonomy guide links, into its design to help users new to Static Code Analysis learn how to perform SCA more efficiently. The CST has been subject to beta testing by experienced static code analysts from the SCAWG to ensure a usable and accurate final product. The implications of the CST in the mission assurance of NASA safety-critical software are profound, as the CST can help identify and reduce false positives and false negatives, fundamentally improving overall SCA efficiency and accuracy.

static code analysis↗

Damage Detection in Rotorcraft Composite Structures Using Thermography and Laser-Based Ultrasound

New rotorcraft structural composite designs incorporate lower structural weight, reduced manufacturing complexity, and improved threat protection. These new structural concepts require nondestructive evaluation inspection technologies that can potentially be field-portable and able to inspect complex geometries for damage or structural defects. Two candidate technologies were considered: Thermography and Laser-Based Ultrasound (Laser UT). Thermography and Laser UT have the advantage of being non-contact inspection methods, with Thermography being a full-field imaging method and Laser UT a point scanning technique. These techniques were used to inspect composite samples that contained both embedded flaws and impact damage of various size and shape. Results showed that the inspection techniques were able to detect both embedded and impact damage with varying degrees of success.

Anastasi, Robert F.↗

Nondestructive test of regenerative chambers

Flat panels simulating internally cooled regenerative thrust chamber walls were fabricated by electroforming, brazing and diffusion bonding to evaluate the feasibility of nondestructive evaluation techniques to detect bonds of various strength integrities. Ultrasonics, holography, and acoustic emission were investigated and found to yield useful and informative data regarding the presence of bond defects in these structures.

Malone, G. A.↗

Reliability Of Inspection By SLAM

Scanning laser acoustic microscopy finds flaws in ceramic specimens. Laser light used to detect distortions, on angstrom scale, produced on surface of specimen by ultrasonic waves transmitted through specimen. From distortion, SLAM creates picture on video monitor of such defects as voids, inclusions, and cracks.

Roth, Don J.↗

Detection of Non-Symmetrical Damage in Smart Plate-Like Structures

A two-dimensional model for in-plane vibrations of a cantilever plate with a non-symmetrical damage is used in the context of defect identification in materials with piezoelectric ceramic patches bonded to their surface. These patches can act both as actuators and sensors in a self-analyzing fashion, which is a characteristic of smart materials. A Galerkin method is used to approximate the dynamic response of these structures. The natural frequency shifts due to the damage are estimated numerically and compared to experimental data obtained from tests on cantilever aluminum plate-like structures damaged at different locations with defects of different depths. The damage location and extent are determined by an enhanced least square identification method. Efficacy of the frequency shift based algorithms is demonstrated using experimental data.

Blanks, H. T.↗

TF41 Engine Fan Disk Seeded Fault Crack Propagation Test

Uncontained engine failures, although rare in occurrence, can have a catastrophic effect on aircraft performance and safety. Engine disk cracks can eventually lead to these type of failures. A number of techniques to detect engine disk cracks have been developed in recent years. However, these technologies have only been validated by disk spin pit tests, not actual engine tests. Due to this, a project was established to perform seeded fault engine tests on a TF41 engine disk fan. A defect was machined in the first stage fan disk of a TF41 engine. The disk was run in a spin pit to initiate a crack. Once initiated, the disk was run in an actual engine test facility. The engine was cycled by a number of start and stops with the goal of propagating the crack to disk burst through low cycle fatigue. Various crack detection techniques were installed on the engine and run real-time during the test to validate their abilities to detect disk cracks. These techniques were based on methods such as change in mass imbalance using vibration or shaft displacement, change in blade position, acoustic emission, and torsional resonance. At the completion of 4474 test cycles, the crack in the TF41 disk was determined to have grown approximately 0.025 inches. This was far less the predicted crack growth based on a fracture mechanics analysis and finite element stress analysis.

Lewicki, David G.↗

Acoustic emission used as weld quality monitor

Acoustic emission technique is described for use as quality control tool in nondestructive inspection of welds. Stress mounts around weld defect until it exceeds yield strength of material. Pressure wave relieving the stress is emitted and followed by oscillations caused by multiple reflections. Acoustic emissions are then detected by sensor similar to ultrasonic sensor.

Jolly, W. O.↗

Health Monitoring of a Rotating Disk Using a Combined Analytical-Experimental Approach

Rotating disks undergo rigorous mechanical loading conditions that make them subject to a variety of failure mechanisms leading to structural deformities and cracking. During operation, periodic loading fluctuations and other related factors cause fractures and hidden internal cracks that can only be detected via noninvasive types of health monitoring and/or nondestructive evaluation. These evaluations go further to inspect material discontinuities and other irregularities that have grown to become critical defects that can lead to failure. Hence, the objectives of this work is to conduct a collective analytical and experimental study to present a well-rounded structural assessment of a rotating disk by means of a health monitoring approach and to appraise the capabilities of an in-house rotor spin system. The analyses utilized the finite element method to analyze the disk with and without an induced crack at different loading levels, such as rotational speeds starting at 3000 up to 10 000 rpm. A parallel experiment was conducted to spin the disk at the desired speeds in an attempt to correlate the experimental findings with the analytical results. The testing involved conducting spin experiments which, covered the rotor in both damaged and undamaged (i.e., notched and unnotched) states. Damaged disks had artificially induced through-thickness flaws represented in the web region ranging from 2.54 to 5.08 cm (1 to 2 in.) in length. This study aims to identify defects that are greater than 1.27 cm (0.5 in.), applying available means of structural health monitoring and nondestructive evaluation, and documenting failure mechanisms experienced by the rotor system under typical turbine engine operating conditions.

Abdul-Aziz, Ali↗

BioSentinel: Optimizing Growth Conditions for Improved Yeast Cell Viability After Long-Term Desiccation

NASA's BioSentinel mission is one of thirteen secondary payloads to be deployed on the Space Launch System Exploration Mission-1 (SLS EM-1). The BioSentinel nanosatellite will be sent into a heliocentric orbit beyond Low Earth Orbit (LEO), to study the effects of deep space radiation on the budding yeast, Saccharomyces cerevisiae. Ionizing radiation encountered in deep space can create damaging lesions in DNA, including double strand breaks (DSBs). Budding yeast is suitable as a biological model to study these effects, as it is eukaryotic, and can be desiccated for prolonged periods while retaining viability, thus serving as a robust analog for human cells. On the ground, yeast cells are grown in liquid medium, then loaded into the wells of microfluidic cards and air dried prior to integration into the payload. Once the spacecraft reaches its target heliocentric orbit, a mixture of growth medium and metabolic indicator dye will be pumped into the microwells at specific time points to rehydrate the cells and allow them to grow. A 3-color LED detection system will measure changes in growth and metabolism resulting from ionizing radiation exposure. BioSentinel contains a wild type control strain and a rad51 mutant that is defective for DNA damage repair. In this study, we will determine the optimal amount of time to grow diploid yeast cells in liquid culture before they are desiccated for space flight. After an extended time in stationary phase, they become more tolerant to desiccation due to stress caused by nitrogen starvation. However, excessive exposure can lead to loss of viability and to a heterogeneous cell population due to sporulation. Since viability loss during desiccation poses a risk to mission success, a stress preconditioning process during initial growth may increase long-term cell viability. To determine the growth period that improves desiccation tolerance but allows for retention of uniform radiation sensitivity, we will grow both strains in liquid medium for a varying number of days (4 to 7), desiccate the cells, and then observe changes to cell viability and ionizing radiation sensitivity over time. Supported by the Space Life Sciences Training Program at NASA Ames Research Center.

Cui, Kaixin↗

Nondestructive testing of Scout rocket motors

The nondestructive tests applied to Scout rocket motors were reviewed and appraised. Analytical techniques were developed to evaluate the capabilities of the radiographic and ultrasonic procedures used. Major problem areas found were the inadequacy of high voltage radiography for detecting unbonds and propellant cracks having narrow widths, the inability to relate the ultrasonic signals received from flat-bottomed holes in standards to those received from real defects and in the general area of the specification of acceptance criteria and how these were to be met. To counter the deficiencies noted, analyses were conducted to the potential utility of radiometric, acoustic, holographic and thermographic techniques for motor and nozzle bond inspection, a new approach to qualifying magnetic particle inspection and the application of acoustic emission analysis to the evaluation of proof and leak test data.

Oaks, A. E.↗

Laser Based Remote and Rapid Inspection for Composite Plates

Composites have been extensively used in aero structure and become the predominate components in the new airframes. Thus, rapid and effective inspection for composite structures is highly desired in aerospace engineering in order to shorten the certificate cycle for new structures or provide safety guarantee for existing ones. In this paper, a laser based remote Lamb wave inspection system is presented and implemented on composite plates for simulated damage detection. The system employs pulsed laser (PL) and scanning laser Doppler vibrometer (SLDV) for noncontact and remote Lamb wave actuation and wavefield sensing. A composite plate with simulated defect (surface bonded quartz rod) is inspected with the PL-SLDV laser system. Wave scattering are observed in the SLDV acquired wavefield and the damage is further evaluated with wavefield imaging and frequency wavenumber analysis. Potential application towards automatic PL Lamb wave excitation is also explored through employing an industry robotic arm towards rapid inspection.

Lamb waves↗

Screening and Qualification of BME Feedthrough Capacitors for a Space Project

Surface mount technology feedthrough ceramic capacitors are gaining popularity in Hi-Rel systems due to small size and great filtering characteristics. In this work, BME feedthrough capacitors compliant with AEC-Q200 requirements have been evaluated, screened and qualified for a space project. Evaluation included analysis of the effect of post-soldering thermal shocks, temperature dependencies of leakage currents, distribution of breakdown voltages, assessments of high-current capability, and thermal resistance of the parts. The parts have been screened and qualified at conditions close to the military requirements for ceramic capacitors. No failures were detected during screening including burning-in, but two samples failed during monitored 2000 hour life testing at 125C and two times rated voltage. Failure analysis revealed manufacturing defects that required additional analysis of screening and qualification test conditions. Highly accelerated life testing (HALT) has been carried out to assess reliability acceleration factors and the probability of failure at the use conditions. An approach to selection of adequate burning-in and life test conditions is discussed.

Alexander Teverovsky↗

Screening and Qualification of BME Feedthrough Capacitors for a Space Project

Surface mount technology feedthrough ceramic capacitors are gaining popularity in Hi-Rel systems due to small size and great filtering characteristics. In this work, BME feedthrough capacitors compliant with AEC-Q200 requirements have been evaluated, screened and qualified for a space project. Evaluation included analysis of the effect of post-soldering thermal shocks, temperature dependencies of leakage currents, distribution of breakdown voltages, assessments of high-current capability, and thermal resistance of the parts. The parts have been screened and qualified at conditions close to the military requirements for ceramic capacitors. No failures were detected during screening including burning-in, but two samples failed during monitored 2000 hour life testing at 125C and two times rated voltage. Failure analysis revealed manufacturing defects that required additional analysis of screening and qualification test conditions. Highly accelerated life testing (HALT) has been carried out to assess reliability acceleration factors and the probability of failure at the use conditions. An approach to selection of adequate burning-in and life test conditions is discussed.

Alexander Teverovsky↗