Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DRAG”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Experimental trim drag values for conventional and supercritical wings

Supercritical wings were studied to determine whether they incur higher trim drag values at cruise conditions than wide body technology wings. Relative trim drag increments were measured in an experimental wind tunnel investigation. The tests utilized high aspect ratio supercritical wing and a wide body wing in conjunction with five different horizontal tail configurations, mounted on a representative wide body fuselage. The three low tail configurations and two T tail configurations were chosen to measure the effects on horizontal tail size, location, and camber on the trim drag increments for the two wings. The increase in performance (lift to drag ratio) for supercritical wing over the wide body wing was 11 percent for both the optimum low tail and T tail configurations.

Jacobs, P. F.↗
NASA NTRS1982

Turbulent boundary layer drag reduction using riblets

An experimental study of low-speed turbulent boundary layer flow over longitudinally grooved surfaces (i.e., riblets) is discussed. Results obtained with a highly accurate drag balance indicate that v-groove riblet surfaces can produce consistent net drag reductions as large as 8 percent provided the height and spacing of the grooves in terms of law of the wall variables are less than 25 wall units. Momentum balances confirmed these direct drag measurements. Conditionally sampled data indicate that the burst frequency for riblets is approximately the same as that for a flat plate but turbulence intensity is reduced. Attempts to optimize the net drag reduction by varying riblet cross-sectional geometry and alignment are also discussed.

Walsh, M. J.↗
NASA NTRS1983

Turbulent drag reduction for external flows

Paper presents a review and summary of turbulent drag reduction approaches applicable to external flows. Because relatively recent and exhaustive reviews exist for laminar flow control and polymer (hydrodynamic) drag reduction, the paper focuses upon the emerging areas of nonplanar geometry and large eddy alteration. Turbulent control techniques for air generally result in modest (but technologically significant) drag reductions (order of 20 percent or less) whereas hydrodynamic approaches can yield drag reductions the order of 70 percent. Paper also includes suggestions for alternative concepts and optimization of existing approaches.

Bushnell, D. M.↗
NASA NTRS1983

Axisymmetric bluff-body drag reduction using circumferential grooves

The effect of shoulder radiusing and circumferentially grooving the afterbodies of bluff bodies to reduce the base drag at low speeds is discussed. Shoulder radii as large as 2.75 body diameters are examined. Reynolds number based on body diameter varied from 20,000 to 200,000. Results indicate that increasing the shoulder radius to 2.75 body diameters can reduce the drag levels to those of a streamline body having 67 percent greater fineness ratio. For zero shoulder radius, circumferential grooves were found to be effective in reducing body drag for zero shoulder radius in both laminar and tripped flow. Circumferential grooves on the afterbody with a shoulder radius of one-half the body diameter were only effective in reducing drag for laminar flow.

Howard, F. G.↗
NASA NTRS1983

A preliminary investigation of the drag and ventilation characteristics of livestock haulers

A wind tunnel evaluation of the drag and ventilation characteristics of a conventional (unmodified) and five modified subscale model livestock haulers at 0 deg yaw angle has been made. The unmodified livestock hauler has a relatively high drag coefficient, and a low velocity recirculation region exists in the forward portion of the hauler. The use of a streamlined forebody and enclosed gap reduced the drag coefficient of one model by 42% and improved the rate at which contaminants can be flushed from the cargo compartment by a factor of 2.5. From the limited data obtained, any increase in the fraction of open area of the trailer sides was found to improve the trailer ventilation. The use of a ram air inlet can improve the ventilation within the hauler and remove the low velocity recirculation region at the expense of a modest increase in the truck's drag coefficient. A mathematical model for vehicles with ram air or NACA submerged inlets was developed and appears to adequately predict the ventilation characteristics of livestock haulers.

Hoffman, J. A.↗
NASA NTRS1983

Investigation to optimize the passive shock wave-boundary layer control for supercritical airfoil drag reduction

The optimization of passive shock wave/boundary layer control for supercritical airfoil drag reduction was investigated in a 3 in. x 15.4 in. Transonic Blowdown Wind Tunnel. A 14% thick supercritical airfoil was tested with 0%, 1.42% and 2.8% porosities at Mach numbers of .70 to .83. The 1.42% case incorporated a linear increase in porosity with the flow direction while the 2.8% case was uniform porosity. The static pressure distributions over the airfoil, the wake impact pressure data for determining the profile drag, and the Schlieren photographs for porous surface airfoils are presented and compared with the results for solid-surface airfoils. While the results show that linear 1.42% porosity actually led to a slight increase in drag it was found that the uniform 2.8% porosity can lead to a drag reduction of 46% at M = .81.

Nagamatsu, H. T.↗
NASA NTRS1984

Optimization and application of riblets for turbulent drag reduction

Riblet surfaces have been tested in boundary layers having different upstream histories and at higher Reynolds numbers than previously reported. The drag reduction for the riblet surfaces was found to be dependent on the height and spacing of the riblets in law-of-the-wall variables regardless of the free-stream Reynolds number or upstream boundary-layer history. Micro-photographs of the actual riblet geometries are examined to determine the effect of rib details on the riblet drag-reduction performances. To further increase drag-reduction performance, riblet surfaces are combined with another drag-reduction concept, the large-eddy breakup device (LEBU). In addition, the yaw sensitivity of riblets is evaluated, as well as the characteristics of riblet surfaces manufactured out of a thin vinyl sheet.

Walsh, M. J.↗
NASA NTRS1984

Porosity effect on supercritical airfoil drag reduction by shock wave/boundary layer control

An investigation of the passive shock wave/boundary layer control for reducing the drag of 14 percent-thick supercritical airfoil was conducted in the 3 in. x 15.4 in. RPI Transonic Wind Tunnel at transonic Mach numbers. Various porous surfaces with a cavity beneath it was positioned on the area of the airfoil, mounted on the test section bottom wall, where the shock wave occurs. The static pressure distributions over the airfoil, the wake impact pressure survey for determining the profile drag and the Schlieren photographs for porous surfaces are presented and compared with the results for solid surface airfoil. With a uniform porosity surface the normal shock wave for solid surface was changed to a lambda shock wave, and the wake impact pressure data indicated an appreciable drag reduction at transonic Mach numbers. For a free stream Mach number of 0.81 the profile drag coefficient for the airfoil top surface with uniform porosity was 46 percent lower than for the solid surface airfoil.

Nagamatsu, H. T.↗
NASA NTRS1984

NASA research on viscous drag reduction II

An assessment is made of determinations from NASA research on viscous drag reduction for aircraft, which extends to both laminar flow control and turbulent drag reduction methods. Attention is given to achievements in natural and suction-induced laminar flow control, hybrid systems incorporating both principles, turbulent drag reduction by means of low momentum fluid injection from discrete tangential slots, large eddy breakup devices, and an 'ion wind' system that functions on an inversion of the corona wind phenomenon. Surface-based drag reduction effects under study involve 'riblets', or small longitudinal surface striations, convex curvatures, and rigid, wavy walls.

Bushnell, D. M.↗
NASA NTRS1986

Combined Devices for Turbulent-Drag Reduction

Aircraft skin-friction drag reduced as much as 15 percent. One effective drag-reduction technique involves use of riblets. Riblets are longitudinal striations or grooves machined on originally smooth surface. Grooves alined with flow. Grooves have depths and spacings on order of turbulent wallstreak and burst dimensions and designed to change near-wall structure of turbulent boundary layer. Another approach, using large-eddy-breakup (LEBU) devices, or turbulence manipulators or ribbons also demonstrated reductions in local skin friction and net drag in air. LEBU device consists of thin, ribbonlike strips or airfoils suspended parallel to test surface and positioned within turbulent boundary layer. Technique potentially reduce net skin-friction drag by at least 15 percent on turbulent boundary layer of aircraft, representing possible annual savings in fuel costs of $300 to $400 million for U.S. commercial fleet. Also applicable to frictionloss reduction inside pipes and ducts, contributing to increased efficiency of pumps, heat exchangers, air conditioners, and other devices involving fluid flow.

Walsh, M. J.↗
NASA NTRS1985

Turbulent drag reduction for external flows

A summary of turbulent drag reduction approaches applicable to external flows is given. Because relatively recent and exhaustive reviews exist for laminar flow control and polymer (hydrodynamic) drag reduction, the focus here is upon the emerging areas of nonplanar geometry and large-eddy alteration. Turbulent control techniques for air generally result in modest (but technologically significant) drag reductions (order of 20 percent or less), whereas hydrodynamic approaches can yield drag reductions the order of 70 percent. Suggestions are included for alternative concepts and optimization of existing approaches.

Bushnell, D. M.↗
NASA NTRS1985

Effect of flow oscillations on cavity drag and a technique for their control

Experiments to relate the state of the shear layer to cavity drag have been performed in a water channel using a 4" axisymmetric cavity model. Detailed flow measurements in various cavity flow oscillation phases, amplitude amplification along the flow direction, distribution of shear stress, and other momentum flux obtained by laser Doppler velocimeter are presented. Measurements show exponential dependence of cavity drag on the length of the cavity. A jump in the cavity drag coefficient is observed as the cavity flow shows a bluff body wake type behavior. Natural and forced oscillations are introduced by a sinusoidally heated thin-film strip which excites the Tollmein-Schlichting waves in the boundary layer upstream of the gap. For a large gap, self-sustained periodic oscillations are observed, while for smaller gaps, which do not oscillate naturally, periodical oscillations can be obtained by external forcing through the strip heater. The drag of the cavity can be increased by one order of magnitude in the non-oscillating case through external forcing. Also, it is possible to completely eliminate mode switching by external forcing. For the first time, it is demonstrated that amplitude of cavity flow Kelvin-Helmholtz wave is dampened or cancelled by introduction of external perturbation of natural flow frequency but different phase.

Gharib, M.↗
NASA NTRS1986

An investigation of the feasibility of active boundary layer thickening for aircraft drag reduction

The feasibility of using a forward mounted windmilling propeller to extract momentum from the flow around an axisymmetric body to reduce total drag has been studied. Numerical calculations indicate that a net drag reduction is possible when the energy extracted is returned to an aft mounted pusher propeller. However, net drag reduction requires very high device efficiencies. Results of an experimental program to study the coupling between a propeller wake and a turbulent boundary layer are also reported. The experiments showed that a complex coupling exists and simple modes for the flow field are not sufficiently accurate to predict total drag.

Ash, R. L.↗
NASA NTRS1981

Aerodynamic drag reduction tests on a box-shaped vehicle

The intent of the present experiment is to define a near optimum value of drag coefficient for a high volume type of vehicle through the use of a boattail, on a vehicle already having rounded front corners and an underbody seal, or fairing. The results of these tests will constitute a baseline for later follow-on studies to evaluate candidate methods of obtaining afterbody drag coefficients approaching the boattail values, but without resorting to such impractical afterbody extensions. The current modifications to the box-shaped vehicle consisted of a full and truncated boattail in conjunction with the faired and sealed underbody. Drag results from these configurations are compared with corresponding wind tunnel results of a 1/10 scale model. Test velocities ranged up to 96.6 km/h (60 mph) and the corresponding Reynolds numbers ranged up to 1.3 x 10 to the 7th power based on the vehicles length which includes the boattail. A simple coast-down technique was used to define drag.

Peterson, R. L.↗
NASA NTRS1986

Yaw and spin effects on high intensity sound generation and on drag of training projectiles with ring cavities

Projectiles containing axisymmetric ring cavities constitute aeroacoustic sources. These produce high intensity tones which are used for coding in the SAWE (Simulation of Area Weapons Effects) system. Experimental data obtained in a free jet facility are presented describing the effects of yaw, spin and geometric projectile parameters on sound pressure and drag. In general, the sound pressure decreases with increasing yaw angle whereas the drag increases. Spin tends to increase sound pressure levels because of a reduction in asymmetry of flow. Drag increases at zero yaw approximately as the 1.5 power of sound wavelength. A significant part of the drag increase appears to be due to energy loss by sound radiation.

Parthasarathy, S. P.↗
NASA NTRS1986

Wall temperature control of low-speed body drag

The use of thermal means to control drag under turbulent boundary layer conditions is examined. Numerical calculations are presented for both skin friction and (unseparated) pressure drag for turbulent boundary-layer flows over a fuselage-like body with wall heat transfer. In addition, thermal control of separation on a bluff body is investigated. It is shown that a total drag reduction of up to 20 percent can be achieved for wall heating with a wall-to-total-freestream temperature ratio of 2. For streamlined slender bodies, partial wall heating of the forebody can produce almost the same order of total drag reduction as the full body heating case. For bluff bodies, the separation delay from partial wall cooling of the afterbody is approximately the same as for the fully cooled body.

Lin, J. C.↗
NASA NTRS1986

Variation of the drag coefficient and its dependence on sea state

Using a Gill propeller vane anemometer and resistance wave wires over a water column depth of 15 m, simultaneous measurements of the momentum flux and sea surface wave spectra were acquired from the Pisa mast, 28 km offshore in the German Bight during autumn and winter 1979. These data were analyzed to identify the relationship between wind stress and surface waves. It was found that wind stresses for wind speeds above 15 m/s were regularly higher than open ocean wind stresses as reported by Smith (1980) and by Large and Pond (1981) for the same mean wind speed. These results, when described in terms of the drag coefficient, compared closely with the results of Sheppard et al. (1972), who collected surface layer statistics over Lough Neagh, Northern Ireland. After modeling the surface waves of the North Sea as a function of wave saturation (or wave age), it became evident that variations in the magnitude of the drag coefficient could be explained by coincident variations in the surface wave energy spectrum. By applying the wave dependent roughness length model described by Kitaigorodskii (1973), the North Sea drag coefficient was predicted to be larger than drag coefficients reported from the open sea.

Geernaert, G. L.↗
NASA NTRS1986

Determination of lift and drag characteristics of Space Shuttle Orbiter using maximum likelihood estimation technique

This paper presents the technique and results of maximum likelihood estimation used to determine lift and drag characteristics of the Space Shuttle Orbiter. Maximum likelihood estimation uses measurable parameters to estimate nonmeasurable parameters. The nonmeasurable parameters for this case are elements of a nonlinear, dynamic model of the orbiter. The estimated parameters are used to evaluate a cost function that computes the differences between the measured and estimated longitudinal parameters. The case presented is a dynamic analysis. This places less restriction on pitching motion and can provide additional information about the orbiter such as lift and drag characteristics at conditions other than trim, instrument biases, and pitching moment characteristics. In addition, an output of the analysis is an estimate of the values for the individual components of lift and drag that contribute to the total lift and drag. The results show that maximum likelihood estimation is a useful tool for analysis of Space Shuttle Orbiter performance and is also applicable to parameter analysis of other types of aircraft.

Trujillo, B. M.↗