Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DIRECT CURRENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

An active magnetic bearing with high T(sub c) superconducting coils and ferromagnetic cores

A proof-of-feasibility demonstration showed that high-T(sub c) superconductor (HTS) coils can be used in a high-load, active magnetic bearing in LN2. A homopolar radial bearing with commercially wound HTS (Bi 2223) bias and control coils produced over 890 N (200 lb) radial load capacity (measured non-rotatings) and supported a shaft to 14,000 rpm. The goal was to show that HTS coils can operate stably with ferromagnetic cores in a feedback controlled system at a current density similar to that for Cu in LN2. The bias coil, wound with non-twisted, multifilament HTS conductor, dissipated negligible power for its direct current. The control coils, wound with monofilament HTS sheathed in Ag, dissipated negligible power for direct current. AC losses increased rapidly with frequency and quadratically with AC amplitude. Above about 2 Hz, the effective resistance of the control coils exceeds that of the silver which is in electrical parallel with the oxide superconductor. These results show that twisted multifilament conductor is not needed for stable levitation but may be desired to reduce control power for sizable dynamic loads.

Brown, G. V.↗

An active homopolar magnetic bearing with high temperature superconductor (HTS) coils and ferromagnetic cores

A proof-of-feasibility demonstration showed that high temperature superconductor (HTS) coils can be used in a high-load, active magnetic bearing in liquid nitrogen. A homopolar radial bearing with commercially wound HTS (Bi 2223) bias and control coils produced over 200 lb (890 N) radial load capacity (measured non-rotating) and supported a shaft to 14000 rpm. The goal was to show that HTS coils can operate stably with ferromagnetic cores in a feedback controlled system at a current density similar to that in Cu in liquid nitrogen. Design compromises permitted use of circular coils with rectangular cross section. Conductor improvements will eventually permit coil shape optimization, higher current density and higher bearing load capacity. The bias coil, wound with non-twisted, multifilament HTS conductor, required negligible power to carry its direct current. The control coils were wound with monofilament HTS sheathed in Ag. These dissipated negligible power for direct current (i.e. for steady radial load components). When an alternating current (AC) was added, the AC component dissipated power which increased rapidly with frequency and quadratically with AC amplitude. In fact at frequencies above about 2 hz, the effective resistance of the control coil conductor actually exceeds that of the silver which is in electrical parallel with the oxide superconductor. This is at least qualitatively understandable in the context of a Bean-type model of flux and current penetration into a Type II superconductor. Fortunately the dynamic currents required for bearing stability are of small amplitude. These results show that while twisted multifilament conductor is not needed for stable levitation, twisted multifilaments will be required to reduce control power for sizable dynamic loads, such as those due to unbalance.

Brown, G. V.↗

Magnification of starting torques of dc motors by maximum power point trackers in photovoltaic systems

Direct current (dc) motors are used in terrestrial photovoltaic (PV) systems such as in water-pumping systems for irrigation and water supply. Direct current motors may also be used for space applications. Simple and low weight systems including dc motors may be of special interest in space where the motors are directly coupled to the solar cell array (with no storage). The system will operate only during times when sufficient insolation is available. An important performance characteristic of electric motors is the starting to rated torque ratio. Different types of dc motors have different starting torque ratios. These ratios are dictated by the size of solar cell array, and the developed motor torque may not be sufficient to overcome the load starting torque. By including a maximum power point tracker (MPPT) in the PV system, the starting to rated torque ratio will increase, the amount of which depends on the motor type. The starting torque ratio is calculated for the permanent magnet, series and shunt excited dc motors when powered by solar cell arrays for two cases: with and without MPPT's. Defining a motor torque magnification by the ratio of the motor torque with an MPPT to the motor torque without an MPPT, a magnification of 3 was obtained for the permanent magnet motor and a magnification of 7 for both the series and shunt motors. The effect of the variation of solar insolation on the motor starting torque was covered. All motor types are less sensitive to insolation variation in systems including MPPT's as compared to systems with MPPT's. The analysis of this paper will assist the PV system designed to determine whether or not to include an MPPT in the system for a specific motor type.

Appelbaum, Joseph↗

A high current density plasma cathode electron gun

The design, performance, and characteristics of a plasma cathode electron gun are presented. The plasma cathode is based on a hollow cathode direct current discharge, and the electron beam is accelerated by pulse voltage. By discharging at high gas pressure and operating at low gas pressure, both the maximum accelerating voltage and maximum emitting current could be increased. Utilizing argon, with the accelerating voltage up to 9 kV and gas pressure down to 52 mPa, the gun is able to generate an electron beam of about 4.7 A, and the corresponding emitting current density is about 600 A/cm{sup 2}.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Tailored particle current in an optical lattice by a weak time-symmetric harmonic potential

Quantum ratchets exhibit asymptotic currents when driven by a time-periodic potential of zero mean if the proper spatiotemporal symmetries are broken. Recently, there has been debate on whether directed currents may arise for potentials which do not break these symmetries. We show here that in the presence of degeneracies in the quasienergy spectrum, long-lasting directed currents can be induced, even if the time-reversal symmetry is not broken. Our model can be realized with ultracold atoms in optical lattices in the tight-binding regime, and we show that the time scale of the average current can be controlled by extremely weak fields.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Olivine electrode engineering impact on the electrochemical performance of lithium-ion batteries.

High energy and power density lithium iron phosphate was studied for hybrid electric vehicle applications. This work addresses the effects of porosity in a composite electrode using a four-point probe resistivity analyzer, galvanostatic cycling, and electrochemical impedance spectroscopy (EIS). The four-point probe result indicates that the porosity of composite electrode affects the electronic conductivity significantly. This effect is also observed from the cell's pulse current discharge performance. Compared to the direct current (dc) methods used, the EIS data are more sensitive to electrode porosity, especially for electrodes with low porosity values.

36 MATERIALS SCIENCE↗

Effect of reabsorbed recombination radiation on the saturation current of direct gap p-n junctions

The application of the radiative transfer theory for semiconductors to p-n homojunctions subject to low level injection conditions is discussed. By virtue of the interaction of the radiation field with free carriers across the depletion layer, the saturation current density in Shockley's expression for the diode current is reduced at high doping levels. The reduction, due to self-induced photon generation, is noticeable for n-type material owing to the small electron effective mass in direct band-gap III-V compounds. The effect is insignificant in p-type material. At an equilibrium electron concentration of 2 x 10 to the 18th/cu cm in GaAs, a reduction of the saturation current density by 15 percent is predicted. It is concluded that realistic GaAs p-n junctions possess a finite thickness.

Von Roos, O.↗

Electronic inverter assembly with an integral snubber capacitor

A coaxial bus connector has a first end and a second end opposite the first end. The first end has a first positive terminal and a first negative terminal coupled to a primary direct current bus of a primary inverter. The second end has a second positive terminal and a second negative terminal coupled to the secondary direct current bus of a secondary inverter, wherein the coaxial bus connector comprises a dielectric material between a center conductor and a coaxial sleeve to form a snubber capacitor to absorb electrical energy or to absorb voltage spikes.

42 ENGINEERING↗

HOT PLASMA FROM SOLAR ACTIVE REGION CORES: A TEST OF AC AND DC CORONAL HEATING MODELS?

Direct current (DC) models of solar coronal heating invoke magnetic reconnection to convert magnetic free energy into heat, whereas alternating current (AC) models invoke wave dissipation. In both cases the energy is supplied by photospheric footpoint motions. For a given footpoint velocity amplitude, DC models predict lower average heating rates but greater temperature variability when compared to AC models. Therefore, evidence of hot plasma (T > 5 MK) in the cores of active regions could be one of the ways for current observations to distinguish between AC and DC models. We have analyzed data from the X-Ray Telescope (XRT) and the Atmospheric Imaging Assembly for 12 quiescent active region cores, all of which were observed in the XRT Be-thick channel. We did Differential Emission Measure (DEM) analysis and achieved good fits for each data set. We then artificially truncated the hot plasma of the DEM model at 5 MK and examined the resulting fits to the data. For some regions in our sample, the XRT intensities continued to be well-matched by the DEM predictions, even without the hot plasma. This truncation, however, resulted in unacceptable fits for the other regions. This result indicates that the hot plasma is present in these regions, even if the precise DEM distribution cannot be determined with the data available. We conclude that reconnection may be heating the hot plasma component of these active regions.

79 ASTRONOMY AND ASTROPHYSICS↗

The Spin Pumping Effect in a Ferromagnetic Insulator/Normal Metal System: A Simple Quantum Mechanical Model

A simple quantum mechanical model of the spin pumping effect upon the excitation of a ferromagnetic resonance in a magnetic dielectric having a flat interface with a nonmagnetic metal is constructed. The model is based on the solution of the Schrödinger equation for conduction electrons in metal. It is shown that the reflection of electrons from the insulator with an oscillating magnetization with a spin flip gives rise to both a direct and alternating (oscillating with the frequency of the resonance-exciting microwave field) spin fluxes from the ferromagnet to the insulator. In this case, the effect of direct current is small compared to the effect of the alternating current; the role of a small parameter is played by the ratio of the exchange constant of a ferromagnet to the potential barrier between the metal and the dielectric (which is higher than the Fermi energy). The result obtained is consistent with known experimental data. The model constructed provides a simple and clear picture of the origination of the phenomenon and enable one to analyze the dependence of the effect on the system parameters.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Observations of field-aligned currents, particles, and plasma drift in the polar cusps near solstice

Magnetic perturbations observed by the TRIAD magnetometer within two hours of an AE-C spacecraft pass provide field-aligned current data, from the same local time in the northern hemisphere, for a study of the polar cusp. The AE-C spinning mode has allowed the use of the Z-axis magnetometer for Birkeland current observations, in conjunction with particle and drift measurements. The average B(z) were found to be 1.9 nT and -1.1 nT during the first two hourly intervals on January 15, 1977. Measurements from the low energy electron experiment revealed intense fluxes of soft, cusp-like 100 eV Maxwellian electrons throughout the prenoon polar cap. The upward directed current can be identified as the dominant cusp current appropriate for B(y) values lower than zero, while the downward directed current, which has the appropriate sign of a dayside region 1 current, is observed to lie entirely within a westerly, antisunward-convecting plasma.

Bythrow, P. F.↗

Directly Deposited Current Collecting Grids for Alkali Metal Thermal-to-Electric Converter Electrodes

Current collection in porous thin film electrodes on solid electrolytes has been improved by using thick film grids to decrease sheet and contact resistance in RhW and PtW electrodes. The grids are directly deposited on the solid electrolyte either by sputter- or photodeposition, and the electrode deposited over the grid. Comparison of the performance of electrodes having such underlying grids with that of electrodes without such grids has shown performance, as measured by current or power produced, to be improved by 10-30% in electrodes with grids.

Ryan, M. A.↗

Directly Deposited Current Collecting Grids for AMTEC Electrodes

Current collection in porous thin film electrodes on solid electrolytes has been improved by using thick film grids to decrease sheet and contact resistance in RhW and PtW electrodes. The grids are directly deposited on the solid electrolyte, either by sputter or photodepostion, and the electrode is deposited over the grid. Comparison of the performance of electrodes having such underlying grids with that of electodes without such grids has shown performance, as measured by current or power produced, to be improved by 10-30% in electrodes with grids.

Ryan, M. A.↗

Metal-ion-controlled growth and nanoindentation response of 3D, bicontinuous Cu–Fe thin films

Bicontinuous, nanocomposite thin film morphologies depend largely on the deposition conditions applied during physical vapor deposition. With the introduction of high power impulse magnetron sputtering (HiPIMS), the range of potential morphologies achieved during deposition has been increased. In this work, we compare the deposition outcomes between traditional direct-current magnetron sputtering (DCMS) and HiPIMS for a thin film co deposit of Cu and Fe. Modular control of the columnarity, porosity and roughness was achieved by varying the Cu and Fe metal ion currents during deposition. The directionality of the nanostructured phase-separated morphology was also controlled as the ion current increased. At zero ion current for both Cu and Fe sputtered species during DCMS, the film exhibited lateral concentration modulations of Cu and Fe. The directionality of the Cu- and Fe-rich phases shifted to vertical concentration modulations at low ion currents of I Fe = 1A and I Cu = 0:1A and to lateral concentration modulations at relatively moderate ion currents of I Fe = 5A and I Cu = 2A: At high ion currents of I Fe = 18A and I Cu = 2A; a more randomized phase domain structure was observed on the nanoscale. This structural shift is rationalized using an interdiffusion model. Here, the role of different kinds of phase separated morphologies, achieved during DCMS deposition, on the mechanical properties has also been studied. Results indicated increase in hardness, indentation modulus and flow strength values with the increase in indentation strain rates. Bicontinuous Cu-Fe nanocomposites are found to be stronger than multilayer Cu-Fe samples.

36 MATERIALS SCIENCE↗

Plasmonic enhancement of direct optical initiation of explosives

Current Direct Optical Initiation (DOI) detonators use a laser focused onto a thin metal layer to drive a hot plasma and/or fragments into PETN powder. Previous studies showed a dramatic decrease in laser energies required to initiate the detonation using this approach over direct laser illumination of the PETN powder. Plasmonic metal nanostructures have been shown capable of strongly coupling laser energy into adjacent materials. We have incorporated gold nanospheres into PETN powder and are investigating their plasmonic enhancement of direct optical initiation via measurements of threshold laser energies and streak camera measurements for calculation of run to detonation distances compared to other DOI schemes.

Spin-orbit torque-driven magnetization switching and thermal effects studied in Ta\CoFeB\MgO nanowires

We demonstrate magnetization switching in out-of-plane magnetized Ta\CoFeB\MgO nanowires by current pulse injection along the nanowires, both with and without a constant and uniform magnetic field collinear to the current direction. We deduce that an effective torque arising from spin-orbit effects in the multilayer drives the switching mechanism. While the generation of a component of the magnetization along the current direction is crucial for the switching to occur, we observe that even without a longitudinal field thermally generated magnetization fluctuations can lead to switching. Analysis using a generalized Néel-Brown model enables key parameters of the thermally induced spin-orbit torques-driven switching process to be estimated, such as the attempt frequency and the effective energy barrier.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A complete electrical hazard classification system and its application

The Standard for Electrical Safety in the Workplace, NFPA 70E, and relevant OSHA electrical safety standards evolved to address the hazards of 60-Hz power that are faced primarily by electricians, linemen, and others performing facility and utility work. This leaves a substantial gap in the management of electrical hazards in Research and Development (R&D) and specialized high voltage and high power equipment. Examples include lasers, accelerators, capacitor banks, electroplating systems, induction and dielectric heating systems, etc. Although all such systems are fed by 50/60 Hz alternating current (ac) power, we find substantial use of direct current (dc) electrical energy, and the use of capacitors, inductors, batteries, and radiofrequency (RF) power. The electrical hazards of these forms of electricity and their systems are different than for 50160 Hz power. Over the past 10 years there has been an effort to develop a method of classifying all of the electrical hazards found in all types of R&D and utilization equipment. Examples of the variation of these hazards from NFPA 70E include (a) high voltage can be harmless, if the available current is sufficiently low, (b) low voltage can be harmful if the available current/power is high, (c) high voltage capacitor hazards are unique and include severe reflex action, affects on the heart, and tissue damage, and (d) arc flash hazard analysis for dc and capacitor systems are not provided in existing standards. This work has led to a comprehensive electrical hazard classification system that is based on various research conducted over the past 100 years, on analysis of such systems in R&D, and on decades of experience. Initially, national electrical safety codes required the qualified worker only to know the source voltage to determine the shock hazard. Later, as arc flash hazards were understood, the fault current and clearing time were needed. These items are still insufficient to fully characterize all types of electrical hazards. The new comprehensive electrical hazard classification system uses a combination of voltage, shock current available, fault current available, power, energy, and waveform to classify all forms of electrical hazards. Based on this electrical hazard classification system, many new tools have been developed, including (a) work controls for these hazards, (b) better selection of PPE for R&D work, (c) improved training, and (d) a new Severity Ranking Tool that is used to rank electrical accidents and incidents with various forms of electrical energy.

57↗