Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DEFORMATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Plastic deformation of a magnesium oxide 001-plane surface produced by cavitation

An investigation was conducted to examine plastic deformation of a cleaved single-crystal magnesium oxide 001-plane surface exposed to cavitation. Cavitation damage experiments were carried out in distilled water at 25 C by using a magnetostrictive oscillator in close proximity (2 mm) to the surface of the cleaved specimen. The dislocation-etch-pit patterns induced by cavitation were examined and compared with that of microhardness indentations. The results revealed that dislocation-etch-pit patterns around hardness indentations contain both screw and edge dislocations, while the etch-pit patterns on the surface exposed to cavitation contain only screw dislocations. During cavitation, deformation occurred in a thin surface layer, accompanied by work-hardening of the ceramic. The row of screw dislocations underwent a stable growth, which was analyzed crystallographically.

Hattori, S.↗
NASA NTRS1986

Migration of the separation point on a deforming cylinder

An iterative scheme of solving the Navier-Stokes equations for unsteady two-dimensional flow about a deforming and translating cylinder is given. In the kth iteration, the convected vorticity appears as the source term in an equation of transient diffusion of vorticity. A novel integral transform is used to reduce this transient vorticity equation to a k-dimensional heat equation. The bounded solution of this equation is obtained with a general method of superposition for problems involving a moving boundary. An equation describing the migration of the separation point on a deforming cylinder in unsteady cross flows is derived from the analytically obtained velocity field. The radial expansion of the cylinder surface is shown to hasten the separation time and to increase the separation angle. The results imply that in the steady flow past a body that is moving forward and sinking at constant rates, the locus of points at which the azimuthal component of skin friction changes sign originates on the leeward ray at a point downstream of the front tip.

Lin, S. P.↗
NASA NTRS1987

Surface deformation, gravity and the geoid from a three-dimensional convection model at low Rayleigh numbers

The two-dimensional surface deformation, gravity field, and geoid are calculated from the temperature fields of a number of numerical models of constant-viscosity three-dimensional convective flows, heated from within and from below. The surface deformation and the geoid are insensitive to the short-wavelength features of the temperature variation; the gravity field is less smooth, although it still does not clearly indicate the narrowness of the upwelling and downwelling regions at large Rayleigh numbers. The results indicate that the convective upwelling beneath regions showing positive geoid and residual depth anomalies is more localized than the horizontal extent of these features would suggest. The results are relevant to attempts to understand the behavior of the earth mantle.

Craig, Claire Harvey↗
NASA NTRS1985

The role of near-surface plastic deformation in the wear of lamellar solids

It is shown in this paper that the role of surface and near-surface plastic deformation is especially significant in both sliding and abrasive wear of lamellar composites. Lamellar structures were produced artificially from alternate layers of pure copper and pure tin or lead foils. The resulting composites were tested in three different wear tests: single-pass abrasion by a sharp, hard abrader; multiple-pass rubbing by a hard, rounded abrader; and pin-on-disk sliding. In each case the counterface was a hard alloy steel. Tests were run with the composite lamellae in two orientations: perpendicular and parallel to the sliding direction. It was found that the composites had much less wear resistance and greater abradability when oriented perpendicular to the rub direction. The mechanisms for wear particle removal and the role of plastic deformation in the process were studied by plasticity analysis and by microscopic (SEM and optical) observation.

Kennedy, F. E.↗
NASA NTRS1987

Deformation, fatigue and fracture behavior of two cast anisotropic superalloys

Tensile and low cycle fatigue (LCF) tests were conducted on two cast anisotropic superalloys. The effects of temperature, strain rate and stress range were investigated. Deformation behavior was extensively characterized and modeled. LCF and fracture behavior were studied and correlated with deformation behavior.

Milligan, Walter W.↗
NASA NTRS1988

Intraplate deformation, stress in the lithosphere and the driving mechanism for plate motions

During this period work was carried out on three fronts relevant to the understanding of intraplate deformation, stress in the lithosphere, and the driving mechanisms for plate motions: (1) observational constraints, using GPS geodesy on the deformation in the region of the boundry between the Pacific and North American plates in central and southern California; (2) numerical modeling of the effects of temperature dependent lithospheric viscosity on the stress and strain history of extensional regimes; and (3) improvement of estimates of mantle viscosity variation, the long-wave-length density variations in the mantle, and the topography of the core-mantel boundary from modeling of geoid anomalies, nutation, and changes in length of day. These projects are described in more detail, followed by a discussion of meetings attended and a list of abstracts and papers submitted and/or published.

Hager, Bradford H.↗
NASA NTRS1987

Crustal deformation in Great California Earthquake cycles

A model in which coupling is described approximately through a generalized Elsasser model is proposed for computation of the periodic crustal deformation associated with repeated strike-slip earthquakes. The model is found to provide a more realistic physical description of tectonic loading than do simpler kinematic models. Parameters are chosen to model the 1857 and 1906 San Andreas ruptures, and predictions are found to be consistent with data on variations of contemporary surface strain and displacement rates as a function of distance from the 1857 and 1906 rupture traces. Results indicate that the asthenosphere appropriate to describe crustal deformation on the earthquake cycle time scale lies in the lower crust and perhaps the crust-mantle transition zone.

Li, Victor C.↗
NASA NTRS1986

A fractal model for crustal deformation

It is hypothesized that crustal deformation occurs on a scale-invariant matrix of faults. For simplicity, a two-dimensional pattern of hexagons on which strike-slip faulting occurs is considered. The behavior of the system is controlled by a single parameter, the fractal dimension. Deformation occurs on all scales of faults. The fractal dimension determines the fraction of the total displacement that occurs on the first-order or primary faults. The value of the fractal dimension can be obtained from the frequency-magnitude relation for earthquakes. The results are applied to the San Andreas fault system in central California. Earthquake studies give D = 1.90. The main strand of the San Andreas fault is associated with the primary faults of the fractal system. It is predicted that the relative velocity across the main strand is 2.93 cm/yr. The remainder of the relative velocity of 5.5 cm/yr between the Pacific and North American plates occurs on higher-order faults. The predicted value is in reasonably good agreement with the value 3.39 + or - 0.29 cm/yr obtained from geological studies.

Turcotte, D. L.↗
NASA NTRS1987

A digital video model deformation system

The use of solid-state array cameras and a PC-controlled image acquisition system to measure model deformation in a wind tunnel is discussed. This digital system improves an earlier video model deformation system that used high-resolution tube cameras and required the manual measurement of targets on video hardcopy images. The new system eliminates both the vibration-induced distortion associated with tube cameras and the manual readup of video images necessary in the earlier version. Camera calibration and data reduction procedures necessary to convert pixel image plane data from two cameras into wing deflections are presented. Laboratory tests to establish the uncertainty of the system with the geometry to be used are described.

Burner, A. W.↗
NASA NTRS1988

Measurements of coseismic deformation in southern California - 1972-1982

This paper compares records collected in the years 1972-1982 from two classes of instruments at Pinon Flat Observatory (PFO), southern California: the long-base-length (greater than 100 m) strain meters and tiltmeters described by Berger and Lovberg(1970) and Wyatt et al. (1982), respectively; and the short-base-length near-surface tiltmeters. It was found that the signals for static strain changes recorded by the long-base-length strain meters and tiltmeters are in good quantitative agreement with the deformation calculated for a dislocation in an elastic half-space. In contrast, colocated short-base-length tiltmeters produced spurious results, with signals much larger than the theoretical coseismic deformations computed using the U.S. Geological Survey/CalTech network; these signals correlated well with peak site acceleration.

Wyatt, Frank K.↗
NASA NTRS1989

Geodetic measurement of deformation in California

The very long baseline interferometry (VLBI) measurements made in the western U.S. since 1979 as part of the NASA Crustal Dynamics Project provide discrete samples of the temporal and spatial deformation field. The interpretation of the VLBI-derived rates of deformation requires an examination of geologic information and more densely sampled ground-based geodetic data. In the first two of three related studies, triangulation and trilateration data measured on two regional networks, one in the central Mojave Desert and one in the Coast Ranges east of the San Andreas fault, have been processed. At the spatial scales spanned by these local geodetic networks, auxiliary geologic and geophysical data have been utilized to examine the relation between measured incremental strain and the accommodation of strain seen in local geological structures, strain release in earthquakes, and principal stress directions inferred from in situ measurements. In a third study, the geocentric position vectors from a set of 77 VLBI experiments beginning in October 1982 have been used to estimate the tangential rate of change of station positions in the western U.S. in a North-America-Fixed reference frame.

Sauber, Jeanne↗
NASA NTRS1988

Intraplate deformation and closure of the Australia-Antarctica-Africa plate circuit

Plate motion data along the Southeast, Southwest, and Central Indian ridges have been reduced to 67 spreading rates, 38 transform fault azimuths, and 135 earthquake slip vectors in order to study the current motion between the Australian, Antarctic, and African plates and to investigate whether this plate circuit obeys closure. Magnetic profiles are modeled to determine rates consistently over a 3-m.y. time-averaging interval, and the new rates are shown to differ from published rates by as much as 5 mm/yr. The results indicate that Indian Ocean plate circuit nonclosure and the deformation that it suggests are much smaller than previously supposed, and support a model in which the significant deformation occurs in a diffuse plate boundary along the equatorial Indian Ocean between the Central Indian Ridge and the Sumatra Trench.

Demets, Charles↗
NASA NTRS1988

Beyond plate tectonics - Looking at plate deformation with space geodesy

The requirements that must be met by space-geodetic systems in order to constrain the horizontal secular motions associated with the geological deformation of the earth's surface are explored. It is suggested that in order to improve existing plate-motion models, the tangential components of relative velocities on interplate baselines must be resolved to an accuracy of less than 3 mm/yr. Results indicate that measuring the velocities between crustal blocks to + or - 5 mm/yr on 100-km to 1000-km scales can produce geologically significant constraints on the integrated deformation rates across continental plate-boundary zones such as the western United States.

Jordan, Thomas H.↗
NASA NTRS1988

Mechanisms of elevated-temperature deformation in the B2 aluminides NiAl and CoAl

A strain rate change technique, developed previously for distinguishing between pure-metal and alloy-type creep behavior, was used to study the elevated-temperature deformation behavior of the intermetallic compounds NiAl and CoAl. Tests on NiAl were conducted at temperatures between 1100 and 1300 K while tests on CoAl were performed at temperatures ranging from 1200 to 1400 K. NiAl exhibits pure-metal type behavior over the entire temperature range studied. CoAl, however, undergoes a transition from pure-metal to alloy-type deformation behavior as the temperature is decreased from 1400 to 1200 K. Slip appears to be inherently more difficult in CoAl than in NiAl, with lattice friction effects limiting the mobility of dislocations at a much higher tmeperature in CoAl than in NiAl. The superior strength of CoAl at elevated temperatures may, therefore, be related to a greater lattice friction strengthening effect in CoAl than in NiAl.

Yaney, D. L.↗
NASA NTRS1989

The transient behavior of weldpools with a deformed free surface

Transient heat transfer, fluid flow and phase change in a weldpool with a deformed free surface are modeled using a two-dimensional coordinate transfornmation. The theoretical approach makes it possible to accurately model high Marangoni number flows even when the free surface is not horizontal. The method is used to examine the role of surface deformation and surface tension forces in controlling weld penetration during cathode spot welding of steel and aluminum. The calculated flow fields, temperature distributions and weldpool shapes are consistent with experimental findings, and are in reasonable agreement with previously published modeling efforts.

Thompson, M. E.↗
NASA NTRS1989

Deformation and fracture of single-crystal and sintered polycrystalline silicon carbide produced by cavitation

An investigation was conducted to examine the deformation and fracture behavior of single-crystal and sintered polycrystalline SiC surfaces exposed to cavitation. Cavitation erosion experiments were conducted in distilled water at 25 C by using a magnetostrictive oscillator in close proximity (1 mm) to the surface of SiC. The horn frequency was 20 kHz, and the double amplitude of the vibrating disk was 50 microns. The results of the investigation indicate that the SiC (0001) surface could be deformed in a plastic manner during cavitation. Dislocation etch pits were formed when the surface was chemically etched. The number of defects, including dislocations in SiC (0001) surface, increased with increasing exposure time to cavitation. The presence of intrinsic defects such as voids in the surficial layers of the sintered polycrystalline SiC determined the zones at which fractured grains and fracture pits (pores) were generated. Single-crystal SiC had superior erosion resistance to that of sintered polycrystalline SiC.

Miyoshi, Kazuhisa↗
NASA NTRS1990

Optical Detection Of Deformations Of An Antenna

Proposed control subsystem generates small aiming-bias signals to correct for deviations of 70-m-diameter reflector of microwave antenna from its ideal shape. Takes optical measurements to determine deformations produced by such environmental factors as wind, gravity, and thermal differentials. Using these measurements, subsystem estimates misalignment of radiation pattern caused by deformations. Signals to correct for estimated misalignment added to angle-command signals of main antenna-aiming system. To measure deviations laser ranging devices placed at base of feed on rigid intermediate reference structure, white retroreflectors placed on parts that deviate from assigned positions relative to intermediate reference structure.

Schumacher, L. L.↗