Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Compression Ratio”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Hydrodynamics of binary coalescence. 1: Polytropes with stiff equations of state

We performed a series of three-dimensional hydrodynamic calculations of binary coalescence using the smoothed particle hydrodynamics (SPH) method. The initial conditions are exact polytropic equilibrium configurations on the verge of dynamical instability. We consider synchronized equilbria only and concentrate on stiff equations of state, with adiabatic Gamma greater than 5/3. We assume that the polytropic constants (K identically equal to P/(rho(exp Gamma)) are the same for both components. These conditions apply well to models of neutron star binaries. Accordingly, we discuss our results in the context of the Laser Interferometer Gravitational-Wave Observatory (LIGO) project, and we calculate the emission of gravitational radiation in the quadruple approximation. The fully nonlinear development of the instability is followed using SPH until a new equilibrium configuration is reached by the system. We find that the properties of this final configuration depend sensitively on both the compressibility and mass ratio. An axisymmetric merged configuration is always produced when the adiabatic exponent Gamma approximately less than 2.3. As a consequence, the emission of gravitational radiation shuts off abruptly right after the onset of dynamical instability. In contrast, triaxial merged configurations are obtained when Gamma approximately greater than 2.3, and the system continues to emit gravitational waves after the final coalescence. Systems with mass ratios q not equal to 1 typically become dynamically unstable before the onset of mass transfer. Stable mass transfer from one neutron star to another in a close binary is therefore probably ruled out. For a mass ratio q approximately less than 0.5, however, dynamical mass transfer can temporarily retard the coalescence by causing a rapid reexpansion of the binary into a new, slightly eccentric but dynamically stable orbit. The maximum amplitude h(sub max) and peak luminosity L(sub max) of the gravitational waves emitted during the final coalescence are nearly independent of Gamma, but depend sensitively on the mass ratio q. The approximate scalings we find are h(sub max) varies as q(exp 2) and L(sub max) varies as q(exp 6) for q close to unity.

Rasio, Frederic A.↗

Control-Relevant Modeling, Analysis, and Design for Scramjet-Powered Hypersonic Vehicles

Within this paper, control-relevant vehicle design concepts are examined using a widely used 3 DOF (plus flexibility) nonlinear model for the longitudinal dynamics of a generic carrot-shaped scramjet powered hypersonic vehicle. Trade studies associated with vehicle/engine parameters are examined. The impact of parameters on control-relevant static properties (e.g. level-flight trimmable region, trim controls, AOA, thrust margin) and dynamic properties (e.g. instability and right half plane zero associated with flight path angle) are examined. Specific parameters considered include: inlet height, diffuser area ratio, lower forebody compression ramp inclination angle, engine location, center of gravity, and mass. Vehicle optimizations is also examined. Both static and dynamic considerations are addressed. The gap-metric optimized vehicle is obtained to illustrate how this control-centric concept can be used to "reduce" scheduling requirements for the final control system. A classic inner-outer loop control architecture and methodology is used to shed light on how specific vehicle/engine design parameter selections impact control system design. In short, the work represents an important first step toward revealing fundamental tradeoffs and systematically treating control-relevant vehicle design.

Rodriguez, Armando A.↗

Aligning Arrays of Lenses and Single-Mode Optical Fibers

A procedure now under development is intended to enable the precise alignment of sheet arrays of microscopic lenses with the end faces of a coherent bundle of as many as 1,000 single-mode optical fibers packed closely in a regular array (see Figure 1). In the original application that prompted this development, the precise assembly of lenses and optical fibers serves as a single-mode spatial filter for a visible-light nulling interferometer. The precision of alignment must be sufficient to limit any remaining wavefront error to a root-mean-square value of less than 1/10 of a wavelength of light. This wavefront-error limit translates to requirements to (1) ensure uniformity of both the lens and fiber arrays, (2) ensure that the lateral distance from the central axis of each lens and the corresponding optical fiber is no more than a fraction of a micron, (3) angularly align the lens-sheet planes and the fiber-bundle end faces to within a few arc seconds, and (4) axially align the lenses and the fiber-bundle end faces to within tens of microns of the focal distance. Figure 2 depicts the apparatus used in the alignment procedure. The beam of light from a Zygo (or equivalent) interferometer is first compressed by a ratio of 20:1 so that upon its return to the interferometer, the beam will be magnified enough to enable measurement of wavefront quality. The apparatus includes relay lenses that enable imaging of the arrays of microscopic lenses in a charge-coupled-device (CCD) camera that is part of the interferometer. One of the arrays of microscopic lenses is mounted on a 6-axis stage, in proximity to the front face of the bundle of optical fibers. The bundle is mounted on a separate stage. A mirror is attached to the back face of the bundle of optical fibers for retroreflection of light. When a microscopic lens and a fiber are aligned with each other, the affected portion of the light is reflected back by the mirror, recollimated by the microscopic lens, transmitted through the relay lenses and the beam compressor/expander, then split so that half goes to a detector and half to the interferometer. The output of the detector is used as a feedback control signal for the six-axis stage to effect alignment.

Liu, Duncan↗

An Experimental Parametric Study of Geometric, Reynolds Number, and Ratio of Specific Heats Effects in Three-Dimensional Sidewall Compression Scramjet Inlets at Mach 6

Since mission profiles for airbreathing hypersonic vehicles such as the National Aero-Space Plane include single-stage-to-orbit requirements, real gas effects may become important with respect to engine performance. The effects of the decrease in the ratio of specific heats have been investigated in generic three-dimensional sidewall compression scramjet inlets with leading-edge sweep angles of 30 and 70 degrees. The effects of a decrease in ratio of specific heats were seen by comparing data from two facilities in two test gases: in the Langley Mach 6 CF4 Tunnel in tetrafluoromethane (where gamma=1.22) and in the Langley 15-Inch Mach 6 Air Tunnel in perfect gas air (where gamma=1.4). In addition to the simulated real gas effects, the parametric effects of cowl position, contraction ratio, leading-edge sweep, and Reynolds number were investigated in the 15-Inch Mach 6 Air Tunnel. The models were instrumented with a total of 45 static pressure orifices distributed on the sidewalls and baseplate. Surface streamline patterns were examined via oil flow, and schlieren videos were made of the external flow field. The results of these tests have significant implications to ground based testing of inlets in facilities which do not operate at flight enthalpies.

Holland, Scott D.↗

Multi-stage heat release of multi-component fuels: Insights and implications for advanced engine operation

Multi-stage heat release (MSHR) is a unique phenomenon typically seen in lean/diluted and low- to intermediate-temperature combustion. Despite its relevance to advanced engine operation, the MSHR of multi-component fuels has barely been quantified. This study aims to characterize the MSHR of multi-component fuels in a rapid compression machine (RCM) at conditions representative of advanced combustion engines. New experimental data are first reported in the RCM at an equivalence ratio of 0.4, pressure of 60 bar and temperatures from 702 to 795 K for a research grade, multi-component gasoline surrogate, termed PACE-20. Here, experiments confirm the existence of MSHR for PACE-20 at all temperatures, and reveal the strong inhibiting effect of temperature on MSHR, where increasing temperature inhibits MSHR by suppressing first stage heat release and promoting second and third stage heat release. A detailed chemical kinetic model is also adopted to model the experiments, with good agreement observed. The response of MSHR characteristics to changes in different engine operating parameters (i.e., temperature, pressure, equivalence ratio and CO 2 dilution level) and fuel compositions (i.e., mole fraction of n-pentane, n-heptane, isooctane, cyclopentane, 1-hexene, ethanol and aromatics in PACE-20) is further evaluated via statistical analysis coupling quasi-random sampling, extensive computer experiments and high-dimensional model representation. The change in MSHR is characterized through 8 quantities of interest (QOIs), i.e., duration and extent of each heat release stage, and their standard deviations. The analysis highlights the dependence of the QOIs on the individual parameters as well as their interplays, with temperature exhibiting the strongest impact among all parameters. Furthermore, it is demonstrated that if MSHR is to be facilitated and combustion phasing is to be extended to enable engine operation at higher compression ratios, it is recommended to operate the engine at low intake temperatures, boosted intake pressures and high CO 2 dilutions (i.e., high EGR levels) with gasoline fuels containing more n-pentane and less aromatics.

42 ENGINEERING↗

Pressure dependence of Poisson’s ratio of glassy Baltic amber studied by Brillouin scattering spectroscopy

Amber is a typical natural glass with very long aging time. Elastic properties of amber at high pressures have been studied using Brillouin scattering and a diamond anvil cell. Both longitudinal and transverse acoustic modes have been observed up to 12 GPa. The pressure dependences of longitudinal, shear, Young’s, and bulk moduli, compressibility, and Poisson’s ratio were determined. The longitudinal, shear, Young’s, bulk moduli show the remarkable increase, and compressibility shows a marked decrease with increasing pressure. However, it is found that the pressure dependence of Poisson’s ratio is very small. The mechanism of this small pressure dependence was discussed. Finally, the Cauchy type relation between longitudinal and shear moduli was examined. Its coefficients show the deviation from the Cauchy relation owing to the coexistence of different intermolecular interactions in amber.

07 ISOTOPE AND RADIATION SOURCES↗

Non-linear properties of metallic cellular materials with a negative Poisson's ratio

Negative Poisson's ratio copper foam was prepared and characterized experimentally. The transformation into re-entrant foam was accomplished by applying sequential permanent compressions above the yield point to achieve a triaxial compression. The Poisson's ratio of the re-entrant foam depended on strain and attained a relative minimum at strains near zero. Poisson's ratio as small as -0.8 was achieved. The strain dependence of properties occurred over a narrower range of strain than in the polymer foams studied earlier. Annealing of the foam resulted in a slightly greater magnitude of negative Poisson's ratio and greater toughness at the expense of a decrease in the Young's modulus.

Choi, J. B.↗

Study by the Prandtl-Glauert method of compressibility effects and critical Mach number for ellipsoids of various aspect ratios and thickness ratios

By using the Prandtl-Glauert method that is valid for three-dimensional flow problems, the value of the maximum incremental velocity for compressible flow about thin ellipsoids at zero angle of attack is calculated as a function of the Mach number for various aspect ratios and thickness ratios. The critical Mach numbers of the various ellipsoids are also determined. The results indicate an increase in critical Mach number with decrease in aspect ratio which is large enough to explain experimental results on low-aspect-ratio wings at zero lift.

Hess, Robert V↗

New theoretical models and ratio imaging techniques associated with the NASA earth resources spectral information system

Four independent investigations are reported; in general these are concerned with improving and utilizing the correlation between the physical properties of natural materials as evidenced in laboratory spectra and spectral data collected by multispectral scanners. In one investigation, two theoretical models were devised that permit the calculation of spectral emittance spectra for rock and mineral surfaces of various particle sizes. The simpler of the two models can be used to qualitatively predict the effect of texture on the spectral emittance of rocks and minerals; it is also potentially useful as an aid in predicting the identification of natural atmospheric aerosol constituents. The second investigation determined, via an infrared ratio imaging technique, the best pair of infrared filters for silicate rock-type discrimination. In a third investigation, laboratory spectra of natural materials were compressed into 11-digit ratio codes for use in feature selection, in searches for false alarm candidates, and eventually for use as training sets in completely automatic data processors. In the fourth investigation, general outlines of a ratio preprocessor and an automatic recognition map processor are developed for on-board data processing in the space shuttle era.

Vincent, R. K.↗

Influence of CaO/FeO ratio on the formation mechanism and properties of alkali-activated Fe-rich slags

Highlights: • Effect of the CaO/FeO molar ratio in alkali-activated Fe-rich slags is unraveled. • Low CaO/FeO molar ratios enhance the early kinetics and compressive strength. • Reaction extent and strength further increase with higher CaO/FeO ratio after 7 days. • Fe{sup 2+}-trioctahedral layers of the binder are hydroxylated and in a silicate phase. • The final strength is determined by the influence of Ca on the reaction products. In the search for CO{sub 2} mitigating cement technologies, alkali-activated Fe-rich slags present a possible alternative. The influence of the chemical composition of the synthetic Fe-silicate slag on the reaction mechanisms is assessed by varying the CaO/FeO molar ratio. The alkali-activated Fe-rich slags consist of trioctahedral layers that are shown to be hydroxylated and in contact with silicates, in a similar way to phyllosilicate minerals. The formation of this phyllosilicate-like structure is hindered during the first days for samples with high CaO/FeO ratios, because of the partial incorporation of Ca in the trioctahedral layers. At later ages, the samples with higher CaO/FeO ratios gain in reaction extent, to exceed the reaction extent of low CaO/FeO ratios at 28 days and beyond. The increase in compressive strength is even more pronounced than the effect on the reaction extent, which underlines the importance of Ca on the inherent strength of the binding phases.

36 MATERIALS SCIENCE↗

Exploring the Effects of Piston Bowl Geometry and Injector Included Angle on Dual-Fuel and Single-Fuel RCCI

Abstract Reactivity control compression ignition (RCCI) is a low-temperature combustion technique that has been proposed to meet the current demand for high thermal efficiency and low engine-out emissions. However, its requirement of two separate fuel systems (i.e., a low-reactivity fuel system and a high-reactivity fuel system) has been one of its major challenges in the last decade. This leads to the single-fuel RCCI concept, where the secondary fuel (reformates of diesel) is generated from the primary fuel (diesel) through catalytic partial oxidation reformation. Following the in-depth analysis of the reformate fuel (reformates of diesel) and its benefit as the low-reactivity fuel with diesel, the effects of the start of injection (SOI) timing of diesel and the energy-based blend ratio were also studied in detail. In this study, the effects of piston profile and the injector included angles were experimentally examined using both conventional fuel pairs (gasoline—diesel and natural gas—diesel) and reformate RCCI. A validated computational fluid dynamics (CFD) model was also used for a better understanding of the experimental trends. Comparing a reentrant bowl piston with a shallow bowl piston at a constant compression ratio and SOI, the latter showed better thermal efficiency, regardless of the fuel combination, due to its 10% lower surface area for the heat transfer. Comparing the 150-degree included angle and 60-degree included angle on the shallow bowl piston, the latter showed better combustion efficiency, regardless of the fuel combination, due to its earlier combustion phasing (at constant SOI timing). The effect was particularly prominent on reformate RCCI because of its incredibly high diluent concentration, which retards the combustion further for the 150-deg injector. Later, using convergecfd, seven different injector included angles were studied at a constant SOI. With the change in injector included angle, the region of the cylinder targeted by the fuel spray varies significantly, and it was found to have a significant impact on the combustion efficiency and the engine-out emissions. As the injector included angle changed from 60-deg to 150-deg, the combustion efficiency increased by 15% and the CO, NOx, and HC emissions decreased by 96%, 70%, and 86%, respectively.

Engineering↗

Low-frequency waves in a high-beta collisionless plasma Polarization, compressibility and helicity

This paper considers the linear theory of waves near and below the ion cyclotron frequency in an isothermal electron-ion Vlasov plasma which is isotropic, homogeneous and magnetized. Numerical solutions of the full dispersion equation for the magnetosonic/whistler and Alfven/ion cyclotron modes at beta(i) = 1.0 are presented, and the polarizations, compressibilities, helicities, ion Alfven ratios and ion cross-helicities are exhibited and compared. At sufficiently large beta(i) and theta, the angle of propagation with respect to the magnetic field, the real part of the polarization of the Alfven/ion cyclotron wave changes sign, so that, for such parameters, this mode is no longer left-hand polarized. The Alfven/ion cyclotron mode becomes more compressive as the wavenumber increases, whereas the magnetosonic/whistler becomes more compressive with increasing theta.

Gary, S. P.↗

Measuring Poisson Ratios at Low Temperatures

Simple extensometer ring measures bulges of specimens in compression. New method of measuring Poisson's ratio used on brittle ceramic materials at cryogenic temperatures. Extensometer ring encircles cylindrical specimen. Four strain gauges connected in fully active Wheatstone bridge self-temperature-compensating. Used at temperatures as low as liquid helium.

Boozon, R. S.↗

Fatigue response of notched laminates subjected to tension-compression cyclic loads

The fatigue response of a ((0/45/90/-45)(sub s))(sub 4) T300-5208 graphite-epoxy laminate with a drilled center-hole subjected to various components of tensile and compressive cyclic loads was investigated. Damage evaluation techniques such as stiffness monitoring, penetrant-enhanced X-ray radiography, C-scan, laminate deply and residual strength measurement were used to establish the mechanisms of damage development as well as the effect of such damage on the laminate strength, stiffness and life. Damage modes consisted of transverse matrix cracks, initiating at the hole, in all plies, followed by delamination between plies of different orientation. A characteristic stiffness repsonse during cyclic loading at two load levels was identified and utilized a more reliable indicator of material and residual properties than accumulated cycles. For the load ratios of tension-compression loading, residual tensile strength increased significantly above the virgin strength early in the fatigue life and remained approximately constant to near the end of life. A technique developed for predicting delamination initiation sites along the hole boundary correlated well with experimental evidence.

Bakis, C. E.↗

Comprehensive Studies on Hot Compaction and Vibration-Assisted Compaction Tests of Aluminum Powder

Abstract Aluminum powder compaction was studied using both test and simulation. Cold compaction, hot compaction, and vibration-assisted (cold) compaction tests were conducted to achieve different density ratios. First, the hot compaction test (at 300 °C, compression pressure 140 MPa) improved about 6% compared with cold compaction under the same compression pressure. Second, although the relative density ratio does not obviously improve at a vibration-assisted (cold) compaction, the strength of the specimens made under vibration loading is much better than those of cold compaction. Additionally, finite element models with well-calibrated Drucker–Prager Cap (DPC) material constitutive model were built in abaqus/standard to simulate the powder compaction process. The results of the finite element model have very good correlations with test results up to the tested range, and this finite element model further predicts the loading conditions needed to achieve the higher density ratios. Two exponential equations of the predicted density ratio were obtained by combining the test data and the simulation results. A new analytical solution was developed to predict the axial pressure versus the density ratio for the powder compaction according to DPC material model. The results between the analytical solution and the simulation model have a very good match.

Engineering↗

An experimental and kinetic modeling study of the ignition of 2-methyl decane

Ignition delay times (IDTs) of 2-methyl decane (C 11 H 24 -2) are measured in a high-pressure shock tube and in a rapid compression machine at equivalence ratios in the range 0.5–2.0 at 90 % dilution, at temperatures in the range 600–1430 K and at pressures of 15 and 30 bar. To clarify the effect of the branched methyl group on fuel oxidation, IDTs of n-undecane (nC 11 H 24 ) are also measured at similar conditions to those measured for C 11 H 24 -2. A new chemical kinetic mechanism, using C3MechV4.0.1 as the core chemistry, is developed and validated against the new experimental data. The thermodynamic properties of the fuel (RH), alkyl (Ṙ), alkyl peroxy (RȮ 2 ), hydroperoxy-alkyl (Q̇OOH), and peroxy hydroperoxy alkyl (Ȯ 2 QOOH) radicals are updated in both the C 11 H 24 -2 and nC 11 H24 models using THERM25. A reaction path flux analysis for C 11 H 24 -2 at different temperatures was conducted. Compared to nC 11 H 24 , C 11 H 24 -2 shows slower reactivity. At low and intermediate temperatures, the chain propagation pathway Q̇OOH ↔ C 11 cyclic ether + ȮH is favored for C 11 H 24 -2, while the chain branching pathway Q̇OOH ↔ Ȯ 2 QOOH ↔ C 11 carbonyl hydroperoxide (KHP) + ȮH is suppressed, leading to lower reactivity compared to nC 11 H 24 . At high temperatures, the presence of the branched methyl group inhibits the direct decomposition of the fuel, resulting in reduced C 2 H 4 formation, which in turn suppresses the reactivity of the fuel.

2-methyl decane↗

Distributed Neural Representation for Reactive In Situ Visualization

Implicit neural representations (INRs) have emerged as a powerful tool for compressing large-scale volume data. This opens up new possibilities for in situ visualization. However, the efficient application of INRs to distributed data remains an underexplored area. Here, in this work, we develop a distributed volumetric neural representation and optimize it for in situ visualization. Our technique eliminates data exchanges between processes, achieving state-of-the-art compression speed, quality and ratios. Our technique also enables the implementation of an efficient strategy for caching large-scale simulation data in high temporal frequencies, further facilitating the use of reactive in situ visualization in a wider range of scientific problems. We integrate this system with the Ascent infrastructure and evaluate its performance and usability using real-world simulations.

Wu, Qi↗