Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMPRESSION BUCKLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Local Circumferential Buckling of Thin Circular Cylindrical Shells

The problem of circumferential buckling of a thin circular cylindrical shell due to compressive hoop stresses which vary in the axial direction is examined. For extremely localised compressive hoop stress distributions resulting from thermal discontinuity effects, or from a uniform, radial line loading, the buckle pattern should also be localised. Simplified analyses into these two types of problem are considered which show that only a limited number of buckle deflection modes needs to be assumed.

CYLINDRICAL SHELL↗

Design detail verification tests for a lightly loaded open-corrugation graphite-epoxy cylinder

Flat corrugated graphite-epoxy panels were tested in compression to verify selected design details of a ring-stiffened cylinder that was designed to support an axial compressive load of 157.6 kN/m without buckling. Three different sizes of subcomponent panels, with the same basic corrugation geometry, were tested: (1) 60.96-cm-long by 45.72-cm-wide panels to evaluate the local buckling strength of the shell wall design; (2) 91.44-cm-long by 45.72-cm-wide panels to evaluate a longitudinal joint and the load-introduction method; and (3) 254.0-cm-long by 91.44-cm-wide panels with four simulated-ring stiffeners to evaluate the ring-attachment method. The test results indicate that the modified shell-wall design, the longitudinal joint, the load-introduction method, and the stiffener-attachment method for the proposed cylinder have adequate strength to support the design load.

Davis, R. C.↗

Initial postbuckling analysis of elastoplastic thin-shear structures

The design of thin shell structures with respect to elastoplastic buckling requires an extended analysis of the influence of initial imperfections. For conservative design, the most critical defect should be assumed with the maximum allowable magnitude. This defect is closely related to the initial postbuckling behavior. An algorithm is given for the quasi-static analysis of the postbuckling behavior of structures that exhibit multiple buckling points. the algorithm based upon an energy criterion allows the computation of the critical perturbation which will be employed for the definition of the critical defect. For computational efficiency, the algorithm uses the reduced basis technique with automatic update of the modal basis. The method is applied to the axisymmetric buckling of cylindrical shells under axial compression, and conclusions are given for future research.

E G Carnoy↗

Structural design criteria for filament-wound composite shells

Advanced composite cylinders, manufactured by filament winding, provide a cost effective solution to many present structural applications; however, the compressive performance of filament-wound cylinders is lower than comparable shells fabricated from unidirectional tape. The objective of this study was to determine the cause of this reduction in thin filament-wound cylinders by relating the manufacturing procedures to the quality of the cylinder and to its compressive performance. The experiments on cylinder buckling were complemented by eigenvalue buckling analysis using a detailed geometric model in a finite element analysis. The applicability of classical buckling analyses was also investigated as a design tool.

Hahn, H. T.↗

TPSAS-NF1676L-26160-DND

The structural performance of two advanced composite tow-steered shells is assessed using experiments and analyses. The fiber angles vary continuously around the shell circumference, and one shell has all 24 tows applied during fabrication, while the second shell uses the fiber placement systems tow drop/add capability to achieve a uniform wall thickness. The shells are tested in compression, and their axial stiffnesses and buckling loads are estimated using linear finite element analyses. Scaled passenger and cargo door cutouts are machined into one side of each shell. Axial stiffnesses and buckling loads of the shells with cutouts are computed using linear finite element analyses. The retested shells carry over 90 percent of the axial stiffness, and 85 percent of the buckling loads, of the shells without cutouts. These small reductions demonstrate the potential of tow steering to mitigate adverse effects of cutouts on the structural performance. The good correlation between experimental buckling loads and linear buckling analyses noted here may result from their circumferential stiffness variation, reducing geometric imperfection sensitivity. Analysis models of both shells were evaluated without and with measured geometric imperfections superposed in different longitudinal orientations. Small variations in prebuckling stiffness and buckling load of the shells are observed.

K C Wu↗

Buckling of rotating beams

The stability of a beam subjected to compressive centrifugal forces arising from steady rotation about an axis which does not pass through the clamped end of the beam is analyzed to determine the critical rotational speeds for buckling in the inplane and out-of-plane directions. The differential equations of motion are solved numerically using an integrating matrix method in combination with an eigenanalysis to determine the eigenvalues from which stability is assessed. The results clarify several differences which have been identified in the literature relating to the proper behavior of the critical rotational speed for buckling as the radius of rotation of the clamped end of the beam is reduced.

White, W. F., Jr.↗

Buckling in polymer monolayers: Molecular-weight dependence

We present systematic investigations of buckling in Langmuir monolayers of polyvinyl acetate formed at the air-water interface. On compression the polymer monolayers are converted to a continuous membrane with a thickness of {approx}2-3 nm of well-defined periodicity, {lambda}{sub b}. Above a certain surface concentration the membrane undergoes a morphological transition buckling, leading to the formation of striped patterns. The periodicity seems to depend on molecular weight as per the predictions of the gravity-bending buckling formalism of Milner et al. for fluidlike films on water. However anomalously low values of bending rigidity and Young's modulus are obtained using this formalism. Hence we have considered an alternative model of buckling-based solidlike films on viscoelastic substrates. The values of bending rigidity and Young's modulus obtained by this method, although lower than expected, are closer to the bulk values. Remarkably, no buckling is found to occur above a certain molecular weight. We have tried to explain the observed molecular-weight dependence in terms of the variation in isothermal compressive modulus of the monolayers with surface concentration as well as provided possible explanations for the obtained low values of mechanical properties similar to that observed for ultrathin polymer films.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Tomography and Simulation of Microstructure Evolution of a Closed-Cell Polymer Foam in Compression

Closed-cell foams in compression exhibit complex deformation characteristics that remain incompletely understood. In this paper the microstructural evolution of closed-cell polymethacrylimide foam was simulated in compression undergoing elastic, compaction, and densification stages. The three-dimensional microstructure of the foam is determined using Micro-Computed Tomography ({micro}-CT), and is converted to material points for simulations using the material point method (MPM). The properties of the cell-walls are determined from nanoindentation on the wall of the foam. MPM simulations captured the three stages of deformations in foam compression. Features of the microstructures from simulations are compared qualitatively with the in-situ observations of the foam under compression using {micro}-CT. The stress-strain curve simulated from MPM compares reasonably with the experimental results. Based on the results from {micro}-CT and MPM simulations, it was found that elastic buckling of cell-walls occurs even in the elastic regime of compression. Within the elastic region, less than 35% of the cell-wall material carries the majority of the compressive load. In the experiment, a shear band was observed as a result of collapse of cells in a weak zone. From this collapsed weak zone a compaction (collapse) wave was seen traveling which eventually lead to the collapse of the entire foam cell-structure. Overall, this methodology will allow prediction of material properties for microstructures driving the optimization of processing and performance in foam materials.

36 MATERIALS SCIENCE↗

Analysis of the flow imbalance on the profile shape during the extrusion of thin magnesium sheets

The extrusion process facilitates the production of magnesium sheets featuring a very thin thickness as well as excellent surface properties by using a single process step only. However, the extrusion of the magnesium sheets applying not optimized process parameters, e.g. low billet temperature or/ and poorly deformable magnesium alloy, produce pronounced buckling and waving of the extruded sheets as well as a variation of accuracy in profile shape along the cross section. The present investigation focuses on the FEM-simulation of the extrusion of magnesium sheets in order to clarify the origin of the mentioned effects. The simulations identify the flow imbalance during extrusion as the main critical factor. Due to the flow imbalance after passing the die a large compression stress zone is formed causing the buckling and waving of the thin sheets. Furthermore, the simulations of the magnesium sheet extrusion reveal that the interaction of the material flow gradients along the width and along the thickness direction near the die orifice lead to the variation of the accuracy in profile shape.

36 MATERIALS SCIENCE↗

Using High-Fidelity Analysis Methods and Experimental Results to Account for the Effects of Imperfections on the Buckling Response of Composite Shell Structures

The results of an experimental and analytical study of the effects of initial imperfections on the buckling response of unstiffened thin-walled compression-loaded graphite-epoxy cylindrical shells are presented. The analytical results include the effects of traditional and nontraditional initial imperfections and uncertainties in the values of selected shell parameters on the buckling loads of the shells. The nonlinear structural analysis results correlate very well with the experimental results. The high-fidelity nonlinear analysis procedure used to generate the analytical results can also be used to form the basis of a new shell design procedure that could reduce the traditional dependence on empirical results in the shell design process. KEYWORDS: high-fidelity nonlinear structural analysis, composite shells, shell stability, initial imperfections

Starnes, James H., Jr.↗

The effect of slots on the buckling and postbuckling behavior of laminated plates

An experimental study was conducted to evaluate the effect of lateral slots on the buckling response, the postbuckling response, and the failure characteristics of flat rectangular graphite-epoxy plates loaded in compression. The slots did not significantly affect the prebuckling and buckling behavior of the plates. The slots caused local changes in the strain distribution and out-of-plane deformations near the slot. Failure loads and modes were strongly affected by slot location. Centrally located slots did not affect the failure loads or failure modes of the plates. Slots located close to an unloaded edge of a plate reduced the postbuckling strength of the plate and affected the failure mode. For one slightly offset slot location, interaction of out-of-plane deformations with the slot tip was observed to affect the failure mode significantly without affecting the failure load.

Gurdal, Z.↗

Buckling test of a 3-meter-diameter corrugated graphite-epoxy ring-stiffened cylinder

A three m diameter by three m long corrugated cylindrical shell with external stiffening rings was tested to failure by buckling. The corrugation geometry for the graphite epoxy composite cylinder wall was optimized to withstand a compressive load producing an ultimate load intensity of 157.6 kN/m without buckling. The test method used to produce the design load intensity was to mount the specimen as a cantilevered cylinder and apply a pure bending moment to the end. A load introduction problem with the specimen was solved by using the BOSOR 4 shell of revolution computer code to analyze the shell and attached loading fixtures. The cylinder test loading achieved was 101 percent of design ultimate, and the resulting mass per unit of shell wall area was 1.96 kg/sq m.

Davis, R. C.↗

Test results from large wing and fuselage panels

This paper presents the first results in an assessment of the strength, stiffness, and damage tolerance of stiffened wing and fuselage subcomponents. Under this NASA funded program, 10 large wing and fuselage panels, variously fabricated by automated tow placement and dry-stitched preform/resin transfer molding, are to be tested. The first test of an automated tow placement six-longeron fuselage panel under shear load was completed successfully. Using NASTRAN finite-element analysis the stiffness of the panel in the linear range prior to buckling was predicted within 3.5 percent. A nonlinear analysis predicted the buckling load within 10 percent and final failure load within 6 percent. The first test of a resin transfer molding six-stringer wing panel under compression was also completed. The panel failed unexpectedly in buckling because of inadequate supporting structure. The average strain was 0.43 percent with a line load of 20.3 kips per inch of width. This strain still exceeds the design allowable strains. Also, the stringers did not debond before failure, which is in contrast to the general behavior of unstitched panels.

Madan, Ram C.↗