Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Axial flow compressor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Preliminary Results of an Altitude-Wind-Tunnel Investigation of an Axial-Flow Gas Turbine-Propeller Engine: Compressor and Turbine Performance Characteristics - 4

As part of an investigation of the performance and operational characteristics of the axial-flow gas turbine-propeller engine, conducted in the Cleveland altitude wind tunnel, the performance characteristics of the compressor and the turbine were obtained. The data presented were obtained at a compressor-inlet ram-pressure ratio of 1.00 for altitudes from 5000 to 35,000 feet, engine speeds from 8000 to 13,000 rpm, and turbine-inlet temperatures from 1400 to 2100 R. The highest compressor pressure ratio obtained was 6.15 at a corrected air flow of 23.7 pounds per second and a corrected turbine-inlet temperature of 2475 R. Peak adiabatic compressor efficiencies of about 77 percent were obtained near the value of corrected air flow corresponding to a corrected engine speed of 13,000 rpm. This maximum efficiency may be somewhat low, however, because of dirt accumulations on the compressor blades. A maximum adiabatic turbine efficiency of 81.5 percent was obtained at rated engine speed for all altitudes and turbine-inlet temperatures investigated.

Wallner, Lewis E.↗

Performance of a single-stage transonic compressor with a blade-tip solidity of 1.3

The design and experimental performance of a 50-centimeter-diameter, single stage, axial flow, transonic compressor with a blade tip solidity of 1.3 are presented. Radial surveys were made of the flow conditions for both the rotor and stator. At design speed, peak efficiencies for both rotor and stage were 0.87 and 0.82, respectively, and occurred at an equivalent weight flow of 29.6 kilograms per second (202 kg/sec/sq m of annulus area). At peak efficiency, the total pressure ratios for both rotor and stage were 1.79 and 1.73, respectively. Stall margin for the stage was 17 percent.

Urasek, D. C.↗

Overall and blade-element performance of a transonic compressor stage with multiple-circular-arc blades at tip speed of 419 meters per second

A 50-centimeter-diameter axial-flow transonic compressor stage with multiple-circular-arc blades was designed and tested to study the effects of blade shape on efficiency and stall margin. At design speed, peak efficiency of 0.80 occurred at an equivalent weight flow of 29.0 kilograms per second. Measured total pressure ratio and total temperature ratio at peak efficiency were 1.69 and 1.20, respectively. The stall margin at design speed and an equivalent weight flow of 29.0 kilograms per second was 9 percent. The measured stall margin at design weight flow and speed was 15 percent. A comparison of rotor performance made with and without the stator showed a decrease in pressure ratio, peak efficiency, and maximum weight flow with the addition of the stator.

Kovich, G.↗

Performance of tandem-bladed transonic compressor rotor with tip speed of 1375 feet per second

The design and experimental performance of a 20-inch diameter tandem-bladed axial-flow transonic compressor rotor is presented. Radial surveys were made of the flow conditions. At design speed the peak efficiency was 0.88 and occurred at an equivalent weight flow of 63 pounds per second. At peak efficiency the total pressure and total temperature ratios were 1.77 and 1.20, respectively. The stall margin at design speed was 10 percent based on weight flows and total pressure ratios at peak efficiency and near stall.

Urasek, D. C.↗

Rotary-Wing Relevant Compressor Aero Research and Technology Development Activities at Glenn Research Center

Technical challenges of compressors for future rotorcraft engines are driven by engine-level and component-level requirements. Cycle analyses are used to highlight the engine-level challenges for 3000, 7500, and 12000 SHP-class engines, which include retention of performance and stability margin at low corrected flows, and matching compressor type, axial-flow or centrifugal, to the low corrected flows and high temperatures in the aft stages. At the component level: power-to-weight and efficiency requirements impel designs with lower inherent aerodynamic stability margin; and, optimum engine overall pressure ratios lead to small blade heights and the associated challenges of scale, particularly increased clearance-to-span ratios. The technical challenges associated with the aerodynamics of low corrected flows and stability management impel the compressor aero research and development efforts reviewed herein. These activities include development of simple models for clearance sensitivities to improve cycle calculations, full-annulus, unsteady Navier-Stokes simulations used to elucidate stall, its inception, and the physics of stall control by discrete tip-injection, development of an actuator-duct-based model for rapid simulation of nonaxisymmetric flow fields (e.g., due inlet circumferential distortion), advanced centrifugal compressor stage development and experimentation, and application of stall control in a T700 engine.

Welch, Gerard E.↗

Overall and blade-element performance of a multiple-circular-arc bladed transonic compressor rotor with tip speed of 1375 feet per second

The design and experimental performance of a 20-inch-diameter multiple-circular-arc bladed axial-flow transonic compressor rotor is presented. Radial surveys of the flow conditions were made. At design speed the peak efficiency was 0.882 and occurred at a weight flow of 64.0 pounds per second. At this point the total-pressure and total-temperature ratios were 1.79 and 1.205, respectively. The stall margin at design speed was 8 percent based on weight flows and total-pressure ratios at experimental peak efficiency and near stall. The measured stall margin was 20 percent at design weight flow and speed.

Kovich, G.↗

Particle flow within a transonic compressor rotor passage with application to laser-Doppler velocimetry

A theoretical analysis was conducted of the dynamic behavior of micron size particles moving in the three-dimensional flow field of a rotating transonic axial-flow air compressor rotor. The particle velocity lag and angular deviation relative to the gas were determined as functions of particle diameter, mass density and radial position. Particle size and density were varied over ranges selected to correspond to typical laser-Doppler velocimeter (LDV) flow field mapping applications. It was found that the particles move essentially on gas stream surfaces and that particle tracking is relatively insensitive to the rotor radial coordinate. Velocity lag and angular deviation increased whenever particle size or mass density increased, and particle tracking was more sensitive to a change in particle diameter than to a corresponding change in mass density. Results indicated that velocity and angular deviations generally less than 1 percent and 1 degree could be achieved with 1 gm/cc tracer particles with diameters of 1 micron or less.

Maxwell, B. R.↗

Variably positioned guide vanes for aerodynamic choking

A choking device to cause a sonic barrier to be formed which reduces the transmission of noise in a direction opposed to the direction of air flow in a compressor that may be part of an aircraft gas turbine engine is described. The noise reduction is accomplished by proper shaping and movement of inlet guide vanes, and an actuator is connected to selected guide vanes to effect movement by programmed amounts as required to choke or partially choke within the design range of the axial-flow-air compressor.

Chestnutt, D.↗

Effects of Inlet Icing on Performance of Axial-flow Turbojet Engine in Natural Icing Conditions

A flight investigation in natural icing conditions was conducted to determine the effect of inlet ice formations on the performance of axial-flow turbojet engines. The results are presented for icing conditions ranging from a liquid-water content of 0.1 to 0.9 gram per cubic meter and water-droplet size from 10 to 27 microns at ambient-air temperature from 13 to 26 degrees F. The data show time histories of jet thrust, air flow, tail-pipe temperature, compressor efficiency, and icing parameters for each icing encounter. The effect of inlet-guide-vane icing was isolated and shown to account for approximately one-half the total reduction in performance caused by inlet icing.

COMPRESSORS - AXIAL FLOW↗

Altitude Wind Tunnel Investigation of the Performance of Compressor, Combustor, and Turbine Components of Prototype J47D (RX1-1) Turbojet Engine

As a portion of an over-all performance investigation of the prototype J47D (RX-1) turbojet engine, performance of the compressor, combustor, and turbine components has been determined in the Lewis altitude wind tunnel over a range of altitude from 5000 to 55,000 feet and at flight Mach numbers from 0.19 to 0.92. Investigations were conducted with the engine operating on an electronic control schedule and slow with a two-lever control system by which fuel flow and exhaust-nozzle area could be controlled separately. Two combustor configurations were investigated.

ENGINES, TURBO-JET↗

Cooled miniature pressure transducers effective at high temperatures

Miniature pressure transducers in compact water-cooled mounts are placed in hotter and more confined environments than previously possible. It quantitatively measures high frequency total pressure fluctuations resulting from rotating stall in an axial flow engine compressor.

Armentrout, E. C.↗