Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Alternative Fuel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 415 records · Page 23

Brief Overview of Subsonic Single Aft Engine (SUSAN) Transport Aircraft Concept and Trade Space Exploration

The SUSAN concept uses a 20-megawatt Electrified Aircraft Propulsion system to enable advance Propulsion Airframe Integration in transport category aircraft. Alternative fuels will be used to reduce the amount of emissions per energy used. By combining these features there is the potential to reduce aircraft emissions by 50 percent per passenger/mile while retaining the size, speed, and range of large regional jets. The SUSAN is has a 750-mile economic mission, a 2500-mile design range and a maximum capacity of 180 passengers. The SUSAN configuration utilizes a single aft mounted engine and distributed electric wing-mounted thrusters on a tube and wing arrangement with a T-tail empennage. The SUSAN Electrofan employs a hybrid powertrain to enable: single turbofan operation on a large transport category aircraft; increased aerodynamic and propulsive efficiency through placement of electric engines; optimized turbofan sizing and efficiency through control and electric boosting, reduced control surface sizing through thrust augmentation. A single use battery is employed as the power source in case of turbofan failure. The design study also considers the constraints of operating within the current airport, airspace, and economic constraints. Forward work includes optimizing the overall aircraft configuration and including certain hard to model features like boundary layer ingestion or natural laminar flow across all appliable subsystems. Additional work forward work is a more extensive analysis of the configuration using alternative fuels.

Ralph Jansen↗

Subsonic Single Aft Engine (SUSAN) Transport Aircraft Concept and Trade Space Exploration

A trade space exploration of a new NASA regional transport aircraft concept called the SUbsonic Single Aft eNgine (SUSAN) Electrofan is presented. The SUSAN concept uses a 20MW Electrified Aircraft Propulsion (EAP) system to enable advance Propulsion Airframe Integration (PAI) in transport category aircraft. Alternative fuels will be used to reduce the amount of emissions per energy used. By combining these features there is the potential to reduce aircraft emissions by 50% per passenger/mile while retaining the size, speed, and range of large regional jets. SUSAN is has a 750 mile economic mission, a 2500 mile design range and a maximum capacity of 180 passengers. The SUSAN configuration utilizes a single aft mounted engine and distributed electric wing-mounted thrusters on a tube and wing arrangement with a T-tail empennage. The SUSAN Electrofan employs a hybrid powertrain to enable: single turbofan operation on a large transport category aircraft; increased aerodynamic and propulsive efficiency through placement of electric engines; optimized turbofan sizing and efficiency through control and electric boosting, reduced control surface sizing through thrust augmentation. A single use battery is employed as the power source in case of turbofan failure. The design study also considers the constraints of operating within the current airport, airspace and economic constraints. This paper presents the status of the trade space exploration; however the concept definition is not finished. Forward work includes optimizing the overall aircraft configuration and including certain hard to model features like boundary layer ingestion or natural laminar flow across all appliable subsystems. Additional work forward work is a more extensive analysis of the configuration using alternative fuels.

Ralph H. Jansen↗

Modification of MELCOR for severe accident analysis of candidate accident tolerant cladding materials

A number of materials are currently under development as candidate accident tolerant fuel and cladding for application in the current fleet of commercial light water reactors (LWRs). The safe, reliable and economic operation of the nation’s nuclear power reactor fleet has always been a top priority for the nuclear industry. Continual improvement of technology, including advanced materials and nuclear fuels, remains central to the industry’s success. Enhancing the accident tolerance of light water reactors became a topic of serious discussion following the 2011 Great East Japan Earthquake, resulting tsunami, and subsequent damage to the Fukushima Daiichi nuclear power plant complex. The overall goal for the development of accident tolerant fuel (ATF) systems for LWRs is to identify alternative fuel system technologies to further enhance the safety, competitiveness, and economics of commercial nuclear power. Designed for use in the current fleet of commercial LWRs, or in reactor concepts with design certifications (GEN-III+), to achieve their goal enhanced ATF must endure loss of active cooling in the reactor core for a considerably longer period of time than the current fuel system, while maintaining or improving performance during normal operation. Many available nuclear fuel performance analysis tools are specifically developed for the current UO 2 – Zirconium alloy fuel system. The MELCOR severe-accident analysis code, under development at the Sandia National Laboratory in New Mexico (SNL-NM) for the US Nuclear Regulatory Commission (NRC), is one of these tools. This article describes modifications made to a version of the MELCOR code by the Idaho National Laboratory (INL) that allows its application to alternate fuel-cladding systems. Preliminary analysis results are presented in this paper for candidate silicon carbide and FeCrAl cladding concepts.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Influence of Injector Location on Part-Load Performance Characteristics of Natural Gas Direct-Injection in a Spark Ignition Engine

Interest in natural gas as an alternative fuel source to petroleum fuels for light-duty vehicle applications has increased due to its domestic availability and stable price compared to gasoline. With its higher hydrogen-to-carbon ratio, natural gas has the potential to reduce engine out carbon dioxide emissions, which has shown to be a strong greenhouse gas contributor. For part-load conditions, the lower flame speeds of natural gas can lead to an increased duration in the inflammation process with traditional port-injection. Direct-injection of natural gas can increase in-cylinder turbulence and has the potential to reduce problems typically associated with port-injection of natural gas, such as lower flame speeds and poor dilution tolerance. A study was designed and executed to investigate the effects of direct-injection of natural gas at part-load conditions. Steady-state tests were performed on a single-cylinder research engine representative of current gasoline direct-injection engines. Tests were performed with direct-injection in the central and side location. The start of injection was varied under stoichiometric conditions in order to study the effects on the mixture formation process. In addition, exhaust gas recirculation was introduced at select conditions in order to investigate the dilution tolerance. Relevant combustion metrics were then analyzed for each scenario. Experimental results suggest that regardless of the injector location, varying the start of injection has a strong impact on the mixture formation process. Delaying the start of injection from 300 to 120°CA BTDC can reduce the early flame development process by nearly 15°CA. While injecting into the cylinder after the intake valves have closed has shown to produce the fastest combustion process, this does not necessarily lead to the highest efficiency, due to increases in pumping and wall heat losses. When comparing the two injection configurations, the side location shows the best performance in terms of combustion metrics and efficiencies. For both systems, part-load dilution tolerance is affected by the injection timing, due to the induced turbulence from the gaseous injection event. CFD simulation results have shown that there is a fundamental difference in how the two injection locations affect the mixture formation process. Delayed injection timing increases the turbulence level in the cylinder at the time of the spark, but reduces the available time for proper mixing. Side injection delivers a gaseous jet that interacts more effectively with the intake induced flow field, and this improves the engine performance in terms of efficiency.

Sevik, James↗

Model predictive control of mixing controlled compression ignition operation for low reactivity fuels

Using gasoline or other low reactivity fuels with a pilot injection or port fuel injection in a compression ignition engine has shown great potential in reducing NOx emissions while keeping high thermal efficiency compared to diesel. However, excessive combustion noise is caused by a high maximum pressure rise rate in the cylinder due to the higher fractions of premixed charge of the low-reactivity fuel. This noise can result in structural damage to engine components and as such, combustion noise limits the range of the operating parameters and makes the control of such engines challenging. In this study, a simulation environment was built up in MATLAB/Simulink leveraging a physics-based zero-dimension combustion model to capture the in-cylinder pressure time traces as well as metrics relevant to thermal efficiency and combustion noise. Here, in order to also facilitate the control of emissions, machine learning models were investigated to capture NOx emissions. A kernel-based extreme learning machine (K-ELM) performed best and had a coefficient of correlation (R-squared) of 0.998. The combustion and NOx emission models are valid for not only conventional gasoline fuel but also oxygenated alternative fuel blends at three different pilot injection strategies. In order to track key combustion metrics while keeping noise and emissions within constraints, a model predictive control (MPC) was applied for a compression ignition engine operating with a range of potential fuels and fuel injection strategies. The MPC is validated under different scenarios, including a load step change, fuel type change, and injection strategy change, with proportional–integral (PI) control as the baseline. The simulation results show that MPC reduces about 26% of ringing intensity in the transient process and 17% at the steady state for E30. Generally, MPC can optimize the overall performance through modifying the main injection timing, pilot fuel mass, and exhaust gas recirculation (EGR) fraction.

42 ENGINEERING↗

Optical investigation of the combustion behaviour inside the engine operating in HCCI mode and using alternative diesel fuel

In order to understand the effect of both the new homogeneous charge compression ignition (HCCI) combustion process and the use of biofuel, optical measurements were carried out into a transparent CR diesel engine. Rape seed methyl ester was used and tests with several injection pressures were performed. OH and HCO radical were detected and their evolutions were analyzed during the whole combustion. Moreover, soot concentration was measured by means the two colour pyrometry method. The reduction of particulate emission with biodiesel as compared to the diesel fuel was noted. Moreover, this effect resulted higher increasing the injection pressure. In the case of RME the oxidation of soot depends mainly from O{sub 2} content of fuel and OH is responsible of the NO formation in the chamber as it was observed for NO{sub x} exhaust emission. Moreover, it was investigated the evolution of HCO and CO into the cylinder. HCO was detected at the start of combustion. During the combustion, HCO oxidizes due to the increasing temperature and it produces CO. Both fuels have similar trend, the highest concentrations are detected for low injection pressure. This effect is more evident for the RME fuel. (author)

09 BIOMASS FUELS↗

A model for droplet heating and evaporation of water-in-oil emulsified fuel

Water-in-oil (W/O) emulsified fuel is a promising alternative fuel by inducing flash boiling of water at high temperature that can improve the atomization of fuel spray. The heating and evaporation process of emulsified fuel droplet is affected by the diffusion and coalescence of small dispersed water droplets in oil during the heating. In this study, a model is developed for the droplet heating and evaporation of W/O emulsified fuel with these key physics considered. The diffusivity of dispersed water droplets in oil is calculated using the Stokes-Einstein equation. The deactivation temperature of surfactant is selected as a criterion for the water coalescence since the water coalescence is due to the deactivation of surfactant. The process of water coalescence is simplified that the dispersed water droplets coalesce into one single water sub-droplet at the center of the oil droplet instantly as the droplet temperature reaches the deactivation temperature of surfactant. The model is validated against experimental data of single droplet under different heating temperatures, surfactant concentrations, and sizes of dispersed water droplets. Based on the proposed model, the effects of fuel properties and heating conditions on the droplet heating and evaporation are analyzed.

Droplet coalescence↗

ReaxFF-based molecular dynamics study of bio-derived polycyclic alkanes as potential alternative jet fuels

This work investigates the initial stages of the pyrolysis of HtH-1 (C 18 H 32 ; 2,2,7,7,8a,8b-hexamethyl-dodecahydrobiphenylene) and HtH-2 (C 18 H 34 ; 1,1',3,3,3',3'-hexamethyl-1,1'-bi(cyclohexane)), which are bio-derived polycyclic alkanes and potential jet fuels, using ReaxFF force field based molecular dynamics (MD) simulations. Global Arrhenius parameters, such as activation energies and pre-exponential factors, are calculated and used to analyze the overall decomposition kinetics of the fuels. HtH-1 decomposes faster than HtH-2 at the same temperature and density conditions, and they have a faster decomposition rate compared to some existing jet-fuels, such as JP-10. A systematic reaction analysis framework developed in this work is applied to determine a temperature-dependent decomposition mechanism. At lower temperature, the central C-C bond connecting the two cyclohexane rings is dominantly broken in both HtH-1 and HtH-2. However, C-CH 3 bond breaking becomes dominant with increasing temperature due to the large increase in entropy during this reaction. Major products from HtH-1 are C 5 H 8 and C 4 H 8 , and those from HtH-2 are C 4 H 8 and C 2 H 4 . The major products predict that HtH-1 has a higher sooting tendency than HtH-2, which is consistent with measurements. The impact of HtH-2 on the pyrolysis of HtH-1 is also investigated in their binary mixtures. HtH-1 and HtH-2 decompose by unimolecular reactions, and they rarely interact with each other during the pyrolysis of the mixtures. Furthermore, this work demonstrates that ReaxFF can be used to investigate pyrolysis and combustion chemistry of existing or future fuels and to contribute to the development of their chemical kinetic models without any a priori input and chemical intuition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A University Consortium on Low Temperature Combustion for High Efficiency, Ultra-Low Emission Engines

The objective of the University consortium was to investigate the fundamental processes that determine the practical boundaries of Low Temperature Combustion (LTC) engines and develop methods to extend those boundaries to improve the fuel economy of these engines, while operating with ultra low emissions. This work involved studies of thermal effects, thermal transients and engine management, internal mixing and stratification, and direct injection strategies for affecting combustion stability. This work also examined spark-assisted Homogenous Charge Compression Ignition (HCCI) and exhaust after-treatment so as to extend the range and maximize the benefit of Homogenous Charge Compression Ignition (HCCI)/ Partially Premixed Compression Ignition (PPCI) operation. In summary the overall goals were; Investigate the fundamental processes that determine the practical boundaries of Low Temperature Combustion (LTC) engines; Develop methods to extend LTC boundaries to improve the fuel economy of HCCI engines fueled on gasoline and alternative blends, while operating with ultra low emissions; and Investigate alternate fuels, ignition and after-treatment for LTC and Partially Premixed compression Ignition (PPCI) engines.

02 PETROLEUM↗

Development of a Raman Spectroscopy Technique to Detect Alternate Transportation Fuel Hydrocarbon Intermediates in Complex Combustion Environments

Spontaneous Raman spectra for important hydrocarbon fuels and combustion intermediates were recorded over a range of low-to-moderate flame temperatures using the multiscalar measurement facility located at Sandia/CA. Recorded spectra were extrapolated to higher flame temperatures and then converted into empirical spectral libraries that can readily be incorporated into existing post-processing analysis models that account for crosstalk from overlapping hydrocarbon channel signal. Performance testing of the developed libraries and reduction methods was conducted through an examination of results from well-characterized laminar reference flames, and was found to provide good agreement. The diagnostic development allows for temporally and spatially resolved flame measurements of speciated hydrocarbon concentrations whose parent is more chemically complex than methane. Such data are needed to validate increasingly complex flame simulations.

Ekoto, Isaac W.↗

Alternative Metal Fuel Casting Techniques: Advanced Fuel Cycle Initiative

This report will summarize current and future work to be done on microwave and continuous casting systems. These systems were chosen for evaluation based on a Metal Fuel Casting Develop review conducted by a body of independent experts in the field of casting and metal fuel fabrication. Technique evaluation will be based on work done by Microwave Synergy, Inc. to produce a non-wetting mold and crucible assembly and several castings using a Ti-Cu alloy. Continuous casting will be evaluated through a report written by Wagstaff Applied Technologies. The report will detail a conceptual design for a laboratory scale continuous casting system, the system design will be support by thermal and fluid flow modeling.

INL/EXT-09-16871↗

Future long-range transports: Prospects for improved fuel efficiency

A status report is provided on current thinking concerning potential improvements in fuel efficiency and possible alternate fuels. Topics reviewed are: (1) historical trends in airplane efficiency; (2) technological opportunities including supercritical aerodynamics, (3) vortex diffusers, (4) composite materials, (5) propulsion systems, (6) active controls, and terminal-area operations; (7) unconventional design concepts, and (8) hydrogen-fueled airplane.

Nagel, A. L.↗

Future long-range transports - Prospects for improved fuel efficiency

A status report is provided on current thinking concerning potential improvements in fuel efficiency and possible alternate fuels. Topics reviewed are: historical trends in airplane efficiency; technological opportunities including supercritical aerodynamics, vortex diffusers, composite materials, propulsion systems, active controls, and terminal-area operations; unconventional design concepts, and hydrogen-fueled airplane.

Nagel, A. L.↗

Alternative aircraft fuels technology

NASA is studying the characteristics of future aircraft fuels produced from either petroleum or nonpetroleum sources such as oil shale or coal. These future hydrocarbon based fuels may have chemical and physical properties that are different from present aviation turbine fuels. This research is aimed at determining what those characteristics may be, how present aircraft and engine components and materials would be affected by fuel specification changes, and what changes in both aircraft and engine design would be required to utilize these future fuels without sacrificing performance, reliability, or safety. This fuels technology program was organized to include both in-house and contract research on the synthesis and characterization of fuels, component evaluations of combustors, turbines, and fuel systems, and, eventually, full-scale engine demonstrations. A review of the various elements of the program and significant results obtained so far are presented.

Grobman, J.↗