Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “transient analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Integrated Multi-Fidelity Model and Co-Simulation Platform for Distribution System Transient and Dynamic Analysis—DistribuDyn

As inverter-based, distributed energy resources (DERs) and variable loads continue to proliferate across distribution systems, it is increasingly important to understand their impacts on system stability and reliability. However, most commercially available simulation tools for distribution planning primarily focus on steady-state and quasi-steady state analysis, offering limited capabilities to study transient and dynamic behaviors.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2021

Two-Phase Turbulence Statistics from High Fidelity Dispersed Droplet Flow Simulations in a Pressurized Water Reactor (PWR) Sub-Channel with Mixing Vanes

In the dispersed flow film boiling regime (DFFB), which exists under post-LOCA (loss-of-coolant accident) conditions in pressurized water reactors (PWRs), there is a complex interplay between droplet dynamics and turbulence in the surrounding steam. Experiments have accredited particular significance to droplet collision with the spacer-grids and mixing vane structures and their consequent positive feedback to the heat transfer recorded in the immediate downstream vicinity. Enabled by high-performance computing (HPC) systems and a massively parallel finite element-based flow solver—PHASTA (Parallel Hierarchic Adaptive Stabilized Transient Analysis)—this work presents high fidelity interface capturing, two-phase, adiabatic simulations in a PWR sub-channel with spacer grids and mixing vanes. Selected flow conditions for the simulations are informed by the experimental data found in the literature, including the steam Reynolds number and collision Weber number (Wec={40,80}), and are characteristic of the DFFB regime. Data were collected from the simulations at an unprecedented resolution, which provides detailed insights into the continuous phase turbulence statistics, highlighting the effects of the presence of droplets and the comparative effect of different Weber numbers on turbulence in the surrounding steam. Further, axial evolution of droplet dynamics was analyzed through cross-sectionally averaged quantities, including droplet volume, surface area and Sauter mean diameter (SMD). The downstream SMD values agree well with the existing empirical correlations for the selected range of Wec. The high-resolution data repository from the simulations herein is expected to be of significance to guide model development for system-level thermal hydraulic codes.

Saini, Nadish↗
NASA NTRS1971

The NASTRAN computer program for structural analysis.

Discussion of a large NASA-sponsored digital computer program for static and dynamic analysis of structures with linear or nonlinear material properties. The program fits to perform buckling analysis, vibration mode analysis of conservative or damped systems, frequency response analysis, and transient response analysis on the IBM 360, UNIVAC 1108, and CDC 6600 computers. It also provides automatic generation of several types of loads such as gravity loads and thermal strain loads, plots of deformed and nondeformed structures, and the choice of alternate analysis methods such as direct or modal formulations of dynamic problems. The program is intended primarily for large problems involving hundreds of thousands of degrees of freedom. A flexible Executive System is provided to facilitate the addition of new functional capabilities to the program.

Macneal, R. H.↗
NASA NTRS1972

Apollo 15 mission report. Supplement 3: Ascent propulsion system final flight evaluation

The results are presented of the postflight analysis of the ascent propulsion system (APS) performance during the Apollo 15 Mission. The information presented includes: (1) calculated performance values for the APS lunar liftoff burn; (2) disucssion of analysis techniques, problems and assumptions; (3) comparison of postflight analysis and preflight prediction; (4) reaction control system (RCS) duty cycle included in the APS performance analysis; (5) transient performance analysis; and (6) the APS propellant consumption values.

Griffin, W. G.↗
NASA NTRS1974

The effect of cyclic feathering motions on dynamic rotor loads

The dynamic loads of a helicopter rotor in forward flight are influenced significantly by the geometric pitch angles between the structural axes of the hub and blade sections and the plane of rotation. The analytical study presented includes elastic coupling between inplane and out-of-plane deflections as a function of geometric pitch between the plane of rotation and the principal axes of inertia of each blade. The numerical evaluation is based on a transient analysis using lumped masses and elastic substructure techniques. A comparison of cases with and without cyclic feathering motion shows the effect on computed dynamic rotor loads.

Harvey, K. W.↗
NASA NTRS1976

Generalized EC&LSS computer program configuration control

The generalized environmental control and life support system (ECLSS) computer program (G189A) simulation of the shuttle orbiter ECLSS was upgraded. The G189A component model configuration was changed to represent the current PV102 and subsequent vehicle ECLSS configurations as defined by baseline ARS and ATCS schematics. The diagrammatic output schematics of the gas, water, and freon loops were also revised to agree with the new ECLSS configuration. The accuracy of the transient analysis was enhanced by incorporating the thermal mass effects of the equipment, structure, and fluid in the ARS gas and water loops and in the ATCS freon loops. The sources of the data used to upgrade the simulation are: (1) ATCS freon loop line sizes and lengths; (2) ARS water loop line sizes and lengths; (3) ARS water loop and ATCS freon loop component and equipment weights; and (4) ARS cabin and avionics bay thermal capacitance and conductance values. A single G189A combination master program library tape was generated which contains all of the master program library versions which were previously maintained on separate tapes. A new component subroutine, PIPETL, was developed and incorporated into the G189A master program library.

Blakely, R. L.↗
NASA NTRS1979

Effect of time dependent flight loads on JT9D-7 performance deterioration

The results of a modal transient analysis of the engine/aircraft system are presented. The response of the JT9D to analytically simulated vertical gusts and landings was predicted using a NASTRAN finite element mathematical model of the JT9D/747 propulsion system. The NASTRAN finite element model of the propulsion system included engine structural models of the fan, low/high pressure compressors, diffuser/turbine cases, and high/low pressure rotors, as well as nacelle models of the inlet cowl, tailcone, and wing pylon. The analysis conducted predicts that an insignificant level of JT9D-7 performance deterioration would occur due to a typical vertical gust encounter or a typical revenue service landing. Analysis of a high sink rate landing with a heavy fuel load indicates the possibility of local wear, however, the lack of an accurate dynamic rotor/seal interference model precludes an accurate quantitative evaluation of performance change for this once-per-airframe-life event.

Jay, A.↗
NASA NTRS1980

A study of nonadiabatic boundary-layer stabilization time in a cryogenic tunnel for typical wing and fuselage models

A theoretical study has been made of the time varying effect of nonadiabatic wall conditions on boundary layer properties for a two-dimensional wing section and an axisymmetric body of revolution typical of a fuselage. The wing section and body of revolution are representative of the root chord and fuselage of what is considered to be a typical size transport model for the National Transonic Facility. The transient analysis was made at a Mach number of 0.85, for stagnation pressures of 2, 6, and 9 atmospheres at several cryogenic values of total temperature for a solid wing and for three different fuselage skin thickness configurations. The analysis considered wing and fuselage sections made from stainless steel, beryllium copper, and aluminum. Examples are presented that may be used to determine the time required to reach an adiabatic condition after a change in total temperature.

Johnson, C. B.↗
NASA NTRS1978

FETSIM user's manual and example

A batch program written in FORTRAN IV which does D.C. and transient analysis of MOS circuits is presented. Circuits employing N-MOS transistors and/or P-MOS transistors in either a bulk technology or an SOS technology, or almost any combination of R-C elements may be analyzed. The program requires as input data the complete circuit topology, device parameters, process parameters, and control parameters. The user can specify initial node conditions and the input pulse format. For example, pulse rise time, fall time, width and time between succeeding pulses are all independently controllable. The program contains a sophisticated mathematical model that can accurately handle either NMOS, P-MOS, Bulk or SOS devices. Sensitivity to process changes is maintained by requiring such process parameters as threshold voltage and doping level as program inputs.

Source record↗
NASA NTRS1981

Structural dynamics payload loads estimates

The development of a full scale payload integration method which reduces the cost of a load cycle and is capable of land long very large systems is discussed. The method solves the coupled booster/payload system equations and does not involve additional approximations as compared to the standard transient analysis. The method is cost effective and directly applicable to the shuttle payload design case.

Engels, R. C.↗
NASA NTRS1983

For operation of the Computer Software Management and Information Center (COSMIC)

Computer programs for large systems of normal equations, an interactive digital signal process, structural analysis of cylindrical thrust chambers, swirling turbulent axisymmetric recirculating flows in practical isothermal combustor geometrics, computation of three dimensional combustor performance, a thermal radiation analysis system, transient response analysis, and a software design analysis are summarized.

Carmon, J. L.↗
NASA NTRS1982

Wake interference for a heated oscillating cylinder

Penney and Jefferson (1966) have studied heat transfer from an oscillating, horizontal wire. The present investigation has the objective to determine the governing parameters which indicate when interaction between an oscillating circular cylinder and its wake will reduce the apparent heat transfer coefficient in quasi-steady conditions, taking into account, if possible, also the determination of the approximate magnitude of the reduction. A definition is provided of a nondimensional vertical mass flux, representing the induced flow due to heating of the stagnant fluid. It is hypothesized that the flux is related to a natural convection parameter which describes the heating of the wake. For oscillation of a circular cylinder in air under the conditions studied, it is found that the application of a cross-flow correlation in a quasi-steady, transient analysis predicts heat transfer parameters in close agreement with experiment over a certain range, provided interaction with the heated wake is avoided.

Mceligot, D. M.↗
NASA NTRS1984

Dynamics of two-phase face seals

An analytic study is presented of the effects of phase change on load support for parallel and tapered face seals. Consideration is given to an adiabatic model for low Reynolds number flow. Numerical integration is carried out of the descriptive fluid equations, giving the opening force due to fluid film pressure. The loci of steady-state solutions are then plotted for water to provide curves of load support as a function of film thickness. For axial excursions of the seal rings, a quasi-steady transient analysis is made. It is found that the load support generated by fluid pressure can be multivalued for a given film thickness. Another finding is that axial disturbances of the seal rings may lead to sudden drops in load support generated by fluid pressure with three possible results. The first is that sufficient damping may permit the seal to return to the previous equilibrium operating position. The second is that the seal may collapse to an equilibrium position of smaller film thickness where face contact is more likely and a significantly higher operating temperature is assured. The third is that a limit cycle of self-sustained oscillation in the axial direction may occur if damping is sufficiently low.

Beeler, R. M.↗
NASA NTRS1982

Structural load prediction methods for space payloads

The state of the art in structural loads prediction procedures for spacecraft is summarized. Three categories of prediction techniques delineated by cost, complexity, comprehensiveness, accuracy, and applications are outlined. The lowest cost method has been used for earth resources, communications, and weather satellites, the medium cost method for sun-synchronous orbits and the large space telescope, and the most expensive for planetary missions, comet rendezvous, and out-of-ecliptic orbits, all assuming Shuttle launch. The lowest cost method involves a mass-acceleration curve. A shock spectra technique predicts a least upper bound for loads. A recovered transient method analyzes the interface acceleration of two connected launch vehicles. The most accurate method devised thus far is a transient analysis of the total launch vehicle/payload dynamic system.

Wada, B. K.↗