Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “torque”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Noncontact Measurement Of Shaft Speed, Torque, And Power

Noncontact fiber-optic sensor and associated electronic equipment measure twist and speed of rotation of shaft. Measurements determine torque and power. Response of sensor remains linear even at cryogenic temperatures. Reflective strips on rotating shaft reflect two series of light pulses back into optical system. Bidirectional coupler in each of two optical fiber paths separates reflected light from incident light, sending it to photodiode for output to analog-to-digital converter and computer. Sensor requires no slip rings or telemetry to transfer signals from shaft. Well suited for providing data on performances of turbopumps for such cryogenic fluids as liquid oxygen and liquid hydrogen.

Madzsar, George C.↗
NASA NTRS1993

Compliant Gearing For Redundant Torque Drive

Elastomeric bearings make torque loads more nearly equal. Bearings couple drive shaft with ring spur gear. Inner elastomeric bearing radially stiff and circumferentially compliant, while outer elastomeric bearings circumferentially stiff and radially compliant. Combination accommodates minor variations in dimensions and placements of gears, shafts, and other components.

Isabelle, C.↗
NASA NTRS1993

Adjustable-Torque Truss-Joint Mechanism

Threaded pin tightened or loosened; tedious trial-and-error procedure shortened. Mechanism joining strut and node in truss structure preloaded to desired stress to ensure tight, compressive fit preventing motion of strut during loading or vibration. Preload stress on stack of Belleville spring washers adjusted by tightening or loosening threaded Belleville-washer-alignment pin. Pin turned, by use of allen wrench, to adjust compression preload on Belleville washers and adjusts joint-operating torque.

Bush, Harold G.↗
NASA NTRS1992

Numerical simulation of satellite-ring interactions - Resonances and satellite-ring torques

The Krook kinetic equation for planetary rings is numerically solved in two spatial dimensions and in time, with (1) interparticle collisions and (2) satellite-forcing, but (3) without self-gravity, for the case of a flattened planetary ring that undergoes gravitational perturbation by a nearby satellite. It is noted that the amplitude of wakes is limited by purely kinematic effects, even in the absence of collisions. Attention is given to the results of a simulation of an inner Lindblad-resonance location, as the distribution approaches steady state; these simulations do not show an increase in velocity dispersion in the resonance zone, obviating a net torque.

Brophy, Thomas G.↗
NASA NTRS1993

Wake-vortex structure from lift and torque induced on a following wing

A procedure based on vortex lattice theory to interpret the lift and torque measured on a following model in a wind tunnel is developed to retrieve the velocity distribution in the vortex wake that caused the induced forces. It is concluded that the retrieval procedure has a potential for reliably determining the structure of vortex wakes that trail from the wings of subsonic transport aircraft. Tests using idealized theoretical models show that the procedure is highly reliable and accurate. However, certain difficulties are found in the retrieval procedure when applied to actual data measured with following wings of various sizes in a wind tunnel.

Rossow, Vernon J.↗
NASA NTRS1934

The torsional stiffness of thin duralumin shells subjected to large torques

This report gives a simple method of estimating the torsional stiffness of thin shells, such as box beams or stressed-skin wings under large torque loads. A general efficiency chart for shells in torsion is established, based on the assumption that the efficiency of the web sheet in resisting deformation decreases linearly with the average stress. The chart is used to calculate the torsional deflections of eight box beams, a test wing panel, and a complete wing; the results of the calculations are shown in comparison with the test results. The agreement is probably as good as might be expected considering the empirical nature of the method and the well-known dispersion between results of tests on thin sheet-metal structures.

Kuhn, Paul↗
NASA NTRS1948

Charts for Determining Preliminary Values of Span-load, Shear, Bending-moment, and Accumulated-torque Distributions of Swept Wings of Various Taper Ratios

Contains charts for use in determining preliminary values of the spanwise-load, shear, bending-moment, and accumulated-torque distributions of swept wings. The charts are based on strip theory and include four aerodynamic-load distributions, two section-moment distributions, and two inertia-load distributions. The taper ratios considered cover the range from 1.0 to 0 and the results are applicable to any angle of sweep.

LOADS, MANEUVERING - WINGS↗
NASA NTRS1934

Negative Thrust and Torque Characteristics of an Adjustable-Pitch Metal Propeller

This report presents the results of a series of negative thrust and torque measurements made with a 4 foot diameter model of a conventional aluminum-alloy propeller. The tests were made in the 20-foot propeller-research tunnel of the National Advisory Committee for Aeronautics. The results show that the negative thrust is considerably affected by the shape and size of the body behind the propeller, that the maximum negative thrust increases with decrease in blade-angle setting, and that the drag of a locked propeller may be greatly reduced by feathering it into the wind. Several examples of possible applications of the data are given.

Hartman, Edwin P↗
NASA NTRS1937

Flight Tests of the Drag and Torque of the Propeller in Terminal-Velocity Dives

The drag and torque of a controllable propeller at various blade-angle settings, and under various diving conditions, were measured by indirect method on F6C-4 airplane in flight. The object of these tests were (1) to provide data on which calculations of the terminal velocity with a throttled engine and the accompanying engine speed could be based and (2) to determine the possibility of utilizing the propeller as an air brake to reduce the terminal velocity. The data obtained were used in the establishment of propeller charts, on the basis of which the terminal velocity and engine speed could be calculated for airplanes whose characteristics fall within the range of these tests. A method is given for the calculation of the terminal velocity with throttled engine and the engine speed.

Rhode, Ricahrd V↗
NASA NTRS1993

Fast gravity, gravity partials, normalized gravity, gravity gradient torque and magnetic field: Derivation, code and data

Derivation of first and second partials of the gravitational potential is given in both normalized and unnormalized form. Two different recursion formulas are considered. Derivation of a general gravity gradient torque algorithm which uses the second partial of the gravitational potential is given. Derivation of the geomagnetic field vector is given in a form that closely mimics the gravitational algorithm. Ada code for all algorithms that precomputes all possible data is given. Test cases comparing the new algorithms with previous data are given, as well as speed comparisons showing the relative efficiencies of the new algorithms.

Gottlieb, Robert G.↗
NASA NTRS1994

Hot gas ingestion effects on fuel control surge recovery and AH-1 rotor drive train torque spikes

This report summarizes the work accomplished through computer simulation to understand the impact of the hydromechanical turbine assembly (TA) fuel control on rocket gas ingestion induced engine surges on the AH-1 (Cobra) helicopter. These surges excite the lightly damped torsional modes of the Cobra rotor drive train and can cause overtorqueing of the tail rotor shaft. The simulation studies show that the hydromechanical TA control has a negligible effect on drive train resonances because its response is sufficiently attenuated at the resonant frequencies. However, a digital electronic control working through the TA control's separate, emergency fuel metering system has been identified as a solution to the overtorqueing problem. State-of-the-art software within the electronic control can provide active damping of the rotor drive train to eliminate excessive torque spikes due to any disturbances including engine surges and aggressive helicopter maneuvers. Modifications to the existing TA hydromechanical control are relatively minor, and existing engine sensors can be utilized by the electronic control. Therefore, it is concluded that the combination of full authority digital electronic control (FADEC) with hydromechanical backup using the existing TA control enhances flight safety, improves helicopter performance, reduces pilot workload, and provides a substantial payback for very little investment.

Tokarski, Frank↗
NASA NTRS1995

High-Torque, Lightweight, Pneumatically Driven Wrench For Small Spaces

Pneumatically driven wrench provides torque up to 3,000 lb. per ft. in small space. Designed to reach into 2.6 x 2.75 x 6 in. pocket. Weighs approximately 25 lbs. Includes reversible pneumatic motor (electric motor could be used instead) and slip clutch. Also includes device indicating total angle through which wrench turned bolt or nut. This feature used for turn-of-the-nut tightening method.

Miller, Thomas W.↗
NASA NTRS1993

Simulation of sloshing dynamics induced forces and torques actuated on dewar container driven by gravity gradient and jitter accelerations in microgravity

Some experimental spacecraft use superconducting sensors for gyro read-out and so must be maintained at a very low temperature. The boil-off from the cryogenic liquid used to cool the sensors can also be used, as the Gravity Probe B (GP-B) spacecraft does, as propellant to maintain attitude control and drag-free operation of the spacecraft. The cryogenic liquid for such spacecraft is, however, susceptible to both slosh-like motion and non-axisymmetric configurations under the influence of various kinds of gravity jitter and gravity gradient accelerations. Hence, it is important to quantify the magnitude of the liquid-induced perturbations on the spacecraft. We use the example of the GP-B to investigate such perturbations by numerical simulations. For this spacecraft disturbances can be imposed on the liquid by atmospheric drag, spacecraft attitude control maneuvers, and the earth's gravity gradient. More generally, onboard machinery vibrations and crew motion can also create disturbances. Recent studies suggest that high frequency disturbances are relatively unimportant in causing liquid motions in comparison to low frequency ones. The results presented here confirm this conclusion. After an initial calibration period, the GP-B spacecraft rotates in orbit at 0.1 rpm about the tank symmetry axis. For this rotation rate, the equilibrium liquid free surface shape is a 'doughnut' configuration for all residual gravity levels of 10(exp -6) g(sub 0) or less, as shown by experiments and by numerical simulations; furthermore, the superfluid behavior of the 1.8 K liquid helium used in GP-B eliminates temperature gradients and therefore such effects as Marangoni convection do not have to be considered. Classical fluid dynamics theory is used as the basis of the numerical simulations here, since Mason's experiments show that the theory is applicable for cryogenic liquid helium in large containers. To study liquid responses to various disturbances, we investigate and simulate three levels of gravity jitter (10(exp -6), 10(exp -7), and 10(exp -8) g(sub 0)) each at three predominant frequencies (0.1, 1.0, and 10 Hz), combined with a gravity gradient appropriate for the GP-B orbit. Dynamical evolution of sloshing dynamics excited fluid forces and torque fluctuations exerted on the dewar container driven by the combined gravity gradient and jitter accelerations are also investigated and simulated.

Hung, R. J.↗
NASA NTRS1995

Baffle Effect on Sloshing-Modulated Torques Responsed to Orbital Accelerations in Microgravity

The behavior of sloshing-dynamics-modulated fluid systems driven by orbital accelerations including gravity gradient and jitter accelerations has been studied. Partly liquid-filled rotating Dewars applicable to a full-scale Gravity Probe-B Spacecraft container with and without baffle are considered. Results show that a slosh wave excited along the liquid-vapor interface induced by jitter-acceleration-dominated orbital accelerations provides a torsional moment with an up-and-down movement of bubble oscillations in the rotating Dewar. The fluctuations of fluid forces and fluid moment (torque) exerted on the Dewar wall of the container caused by slosh-wave excitation driven by orbital accelerations are also investigated. Since the viscous force across a liquid-solid interface and the surface-tension force across a liquid-vapor or liquid-solid interface can greatly contribute to the damping effect of slosh-wave excitation, a rotating Dewar with a baffle provides more areas of liquid-solid, and liquid-vapor, and solid-vapor interfaces than does a rotating Dewar without a baffle. Results show that the damping effect provided by the baffle reduces the amplitudes of force and moment feedback from the fluids to the container-in particular, the components of fluctuations transverse to the direction of the baffle boards.

Pan, H. L.↗
NASA NTRS1997

Virtual Passive Controller for Robot Systems Using Joint Torque Sensors

This paper presents a control method based on virtual passive dynamic control that will stabilize a robot manipulator using joint torque sensors and a simple joint model. The method does not require joint position or velocity feedback for stabilization. The proposed control method is stable in the sense of Lyaponov. The control method was implemented on several joints of a laboratory robot. The controller showed good stability robustness to system parameter error and to the exclusion of nonlinear dynamic effects on the joints. The controller enhanced position tracking performance and, in the absence of position control, dissipated joint energy.

Aldridge, Hal A.↗
NASA NTRS1997

Random Vibration and Torque Tests of Fasteners Secured With Locking Cable, Room Temperature Vulcanized (RTV) Rubber, and Closed Cell Foam to Support the Launch of STS-82

During a walkdown of the Space Transportation System (STS) orbiter for the 82nd Space Shuttle flight (STS-82), technicians found several safety cables for bolts with missing or loose ferrules. Typically, two or three bolts are secured with a cable which passes through one of the holes in the head of each bolt and a ferrule is crimped on each end of the cable to prevent it from coming out of the holes. The purpose of the cable is to prevent bolts from rotating should they become untightened. Other bolts are secured with either a locking cable or wire which is covered with RTV and foam. The RTV and foam would have to be removed to inspect for missing or loose ferrules. To determine whether this was necessary, vibration and torque test fixtures and tests were made to determine whether or not bolts with missing or loose ferrules would unloosen. These tests showed they would not, and the RTV and foam was not removed.

Yost, V. H.↗
NASA NTRS1995

The Topographic Torque on a Bounding Surface of a Rotating Gravitating Fluid and the Excitation by Core Motions of Decadal Fluctuations in the Earth's Rotation

General expressions (with potential applications in several areas of geophysical fluid dynamics) are derived for all three components of the contribution made by the geostrophic part of the pressure field associated with flow in a rotating gravitating fluid to the topographic torque exerted by the fluid on a rigid impermeable bounding surface of any shape. When applied to the Earth's liquid metallic core, which is bounded by nearly spherical surfaces and can be divided into two main regions, the "torosphere" and "polosphere," the expressions reduce to formulae given previously by the author, thereby providing further support for his work and that of others on the role of topographic coupling at the core-mantle boundary in the excitation by core motions of Earth rotation fluctuations on decadal time scales. They also show that recent criticisms of that work are vitiated by mathematical and physical errors. Contrary to these criticisms, the author's scheme for exploiting Earth rotation and other geophysical data (either real or simulated in computer models) in quantitative studies of the topography of the core-mantle boundary (CMB) by intercomparing various models of (a) motions in the core based on geomagnetic secular variation data and (b) CMB topography based on seismological and gravity data has a sound theoretical basis. The practical scope of the scheme is of course limited by the accuracy of real data, but this is a matter for investigation, not a priori assessment.

Hide, Raymond↗