SEARCH · Engineering Papers

Results for “surface roughness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

All sources NASA NTRS DOE OSTI

NASA NTRS1994

Analysis of Airborne Radar Altimetry Measurements of the Greenland Ice Sheet

This dissertation presents an analysis of airborne altimetry measurements taken over the Greenland ice sheet with the 13.9 GHz Advanced Application Flight Experiment (AAFE) pulse compression radar altimeter. This Ku-band instrument was refurbished in 1990 by the Microwave Remote Sensing Laboratory at the University of Massachusetts to obtain high-resolution altitude measurements and to improve the tracking, speed, storage and display capabilities of the radar. In 1991 and 1993, the AAFE altimeter took part in the NASA Multisensor Airborne Altimetry Experiments over Greenland, along with two NASA laser altimeters. Altitude results from both experiments are presented along with comparisons to the laser altimeter and calibration passes over the Sondrestroem runway in Greenland. Although it is too early to make a conclusion about the growth or decay of the ice sheet, these results show that the instrument is capable of measuring small-scale surface changes to within 14 centimeters. In addition, results from these experiments reveal that the radar is sensitive to the different diagenetic regions of the ice sheet. Return waveforms from the wet- snow, percolation and dry-snow zones show varying effects of both surface scattering and sub-surface or volume scattering. Models of each of the diagenetic regions of Greenland are presented along with parameters such as rms surface roughness, rms surface slope and attenuation coefficient of the snow pack obtained by fitting the models to actual return waveforms.

Ferraro, Ellen J.↗

NASA NTRS1999

Remote Sensing for Agriculture, Ecosystems and Hydrology III

The science need for remotely sensed soil moisture has been well established in the hydrologic, climate change and weather forecasting communities. In spite of this well documented science need there are currently no satellite missions flying or funded to make this very important geophysical measurement. There have been a number of experimental aircraft programs that have demonstrated the feasibility of using long wave microwave sensors for estimating soil moisture. Unfortunately, this science driver, soil moisture, imposes very difficult technical requirements for a satellite sensor system. Global soil moisture is driven by a spatial resolution on the order of 20 to 30 km and measurements need to be taken every two to three days to be useful to the science community. The principal sensor to accomplish the soil moisture measurements is an L- band passive microwave radiometer and achieving the spatial and temporal requirements requires a very large antenna. This paper describes the several alternatives to solve the very large antenna challenge and still meet the radiometer sensitivity requirement. The paper also discusses the alternatives considered to obtain the necessary ancillary data for characterizing the surface roughness, the surface temperature and the attenuation affects of vegetation needed to derive the geophysical parameter. Finally, the paper discusses proposed missions and how well they will meet the science requirements.

Engman, Edwin T.↗

NASA NTRS1998

Development of a Satellite Systems for Measuring Soil Moisture

The science need for remotely sensed soil moisture has been well established in the hydrologic, climate change and weather forecasting communities. There also have been a number of programs that have demonstrated the feasibility of using long wave microwave sensors for estimating soil moisture. These have ranged from truck mounted sensors, to intensive airborne campaigns with science objectives. Based on this history of truck and aircraft experiments, the science community has settled on a soil moisture product that meets the following criteria: a two day global repeat, a measured layer of 5 cm of soil, a footprint of 20 to 30 km, and an absolute accuracy of +/- 4% volumetric soil moisture. The principal sensor to accomplish this is an L-band passive microwave radiometer. A soil moisture mission is being proposed for the NASA Earth Systems Science Pathfinder (ESSP) mission which has very real constraints of a limited budget which includes the launch vehicle, and a three year award to launch time schedule. This paper describes ways to solve the very large antenna challenge, and the criteria used to choose the final design for an ESSP proposal. The paper also discusses the alternatives considered to obtain the necessary ancillary data for characterizing the surface roughness, the surface temperature and the attenuation affects of vegetation.

Engman, Edwin T.↗

NASA NTRS2002

An Imaging Laser Altimeter for Lunar Scientific Exploration

A new approach to laser altimetry is offered by the development of micro-lasers and pixilated detectors that enable very high resolution measurement of topography and relatively wide swath observations. An imaging altimeter with a 8x8 array detector working at a probability of less than a single photon/shot could map the Moon or similar sized body in approximately 2 years and provide 5 meter horizontal resolution topography and a 10 centimeter vertical accuracy. In addition, it would provide surface roughness and surface slopes on similar length scales of 5 meters and be able to address a range of problems for which topography or lunar shape is important at the decimeter level. This includes the topography of the polar regions, where ice is thought to have been identified, and also the cratering history of the Moon which could be assessed with a dataset of uniform quality and high resolution.

Source record↗

NASA NTRS2002

An Imaging Laser Altimeter for Lunar Scientific Exploration

Smith, David E.↗

NASA NTRS2011

Laser Peening Effects on Friction Stir Welding

Friction Stir Welding (FSW) is a welding technique that uses frictional heating combined with forging pressure to produce high strength bonds. It is attractive for aerospace applications. Although residual stresses in FSW are generally lower when compared to conventional fusion welds, recent work has shown that significant tensile residual stresses can be present in the weld after fabrication. Therefore, laser shock peening was investigated as a means of moderating the tensile residual stresses produced during welding. This slide presentation reviews the effect of Laser Peening on the weld, in tensile strength, strain, surface roughness, microhardness, surface wear/friction, and fatigue crack growth rates. The study concluded that the laser peening process can result in considerable improvement to crack initiaion, propagation and mechanical properties in FSW.

Hatamleh, Omar↗

NASA NTRS2012

Validation of Aquarius Measurements Using Radiative Transfer Models at L-Band

Aquarius/SAC-D was launched in June 2011 by NASA and CONAE (Argentine space agency). Aquarius includes three L-band (1.4 GHz) radiometers dedicated to measuring sea surface salinity. We report detailed comparisons of Aquarius measurements with radiative transfer model predictions. These comparisons were used as part ofthe initial assessment of Aquarius data. In particular, they were used successfully to estimate the radiometer calibration bias and stability. Further comparisons are being performed to assess the performance of models in the retrieval algorithm for correcting the effect of sources of geophysical "noise" (e.g. the galactic background, atmospheric attenuation and reflected signal from the Sun). Such corrections are critical in bringing the error in retrieved salinity down to the required 0.2 practical salinity unit (psu) on monthly global maps at 150 km by 150 km resolution. The forward models making up the Aquarius simulator have been very useful for preparatory studies in the years leading to Aquarius' launch. The simulator includes various components to compute effects ofthe following processes on the measured signal: 1) emission from Earth surfaces (ocean, land, ice), 2) atmospheric emission and absorption, 3) emission from the Sun, Moon and celestial Sky (directly through the antenna sidelobes or after reflection/scattering at the Earth surface), 4) Faraday rotation, and 5) convolution of the scene by the antenna gain patterns. Since the Aquarius radiometers tum-on in late July 2011, the simulator has been used to perform a first order validation of the data. This included checking the order of magnitude ofthe signal over ocean, land and ice surfaces, checking the relative amplitude of signal at different polarizations, and checking the variation with incidence angle. The comparisons were also used to assess calibration bias and monitor instruments calibration drift. The simulator is also being used in the salinity retrieval. For example, initial assessments of the salinity retrieved from Aquarius data showed degradation in accuracy at locations where glint from the galactic sky background was important. This was traced to an inaccurate correction for the Sky glint. We present comparisons of the simulator prediction to the Aquarius data in order to assess the performances of the models of various physical processes impacting the measurements, such as the effect of sea surface roughness, the impact of the celestial Sky and the Sun emission scattered at the rough ocean surface. We discuss what components of the simulator appear reliable and which ones need improvements. Improved knowledge on the radiative transfer models at L-band will not only lead to better salinity retrieved from Aquarius data, it will also allow be beneficial for SMOS or the upcoming SMAP mission.

Dinnat, E.↗

NASA NTRS2014

Visualization of Capsule Reentry Vehicle Heat Shield Ablation Using Naphthalene PLIF

The Orion Multi-Purpose Crew Vehicle (MPCV) will use an ablative heat shield and improved understanding of the ablation process would be beneficial for design purposes. Given that ablation is a multi-physics process involving heat and mass transfer, codes aiming to predict heat shield ablation are in need of experimental data pertaining to the turbulent transport of ablation products for validation. At The University of Texas at Austin, a technique is being developed that uses planar laser-induced fluorescence (PLIF) of a low-temperature sublimating ablator (naphthalene) to visualize the transport of ablation products in a supersonic flow. Since ablation at reentry temperatures can be difficult to recreate in a laboratory setting it is desirable to create a limited physics problem and simulate the ablation process at relatively low temperature conditions using naphthalene. A scaled Orion MPCV model with a solid naphthalene heat shield has been tested in a Mach 5 wind tunnel at various angles of attack in the current work. PLIF imaging reveals the distribution of the ablation products as they are transported into the heat-shield boundary layer and over the capsule shoulders into the separated shear layer and backshell recirculation region. Visualizations of the capsule shear layer using both naphthalene PLIF and Schlieren imaging compared favorably. High concentrations of naphthalene in the capsule separated flow region, intermittent turbulent structures on the heat shield surface, and interesting details of the capsule shear layer structure were observed using the naphthalene PLIF technique. The capsule shear layer was also shown to generally appear to be more turbulent at lower angles of attack. Furthermore, the PLIF signal increased steadily over the course of a run indicating that during a wind tunnel run the model heated up and the rate of naphthalene ablation increased. The shear layer showed increasing signs of turbulence over the course of a wind tunnel run as well, likely because of the combination of increased surface roughness and surface blowing rate. PLIF imaging also detected regions with a relatively low concentration of naphthalene in the capsule backshell recirculation region that are most likely the result of cross-flow-induced vortices on the capsule afterbody.

Combs, Christopher S.↗

NASA NTRS1993

Evidence for dust contamination on the VETA-1 mirror surface

Relative surface brightness data from the VETA-1 test displayed an energy dependence which was inconsistent with models which assume surface roughness is the only cause of scattering. A means of separating an in-plane component of scattering caused by surface roughness from an azimuthally symmetric component, which is expected from dust, was afforded by images taken while only single quarters of the mirror surface were exposed. In this case, in-plane scattered X-rays should populate only opposing 90 deg azimuthal quadrants of an image centered on the focal point. As such, this approach is a novel, high sensitivity test for detecting extremely small (about 10 exp -5) fractional dust coverage on X-ray optics. Comparison of in-plane and out-of-plane quadrants in these tests indicated that most of the scattered data were azimuthally symmetric, and that the symmetric component was enhanced at lower energies. Both results support a model which invokes the wing scan results with a combination of dust and surface roughness induced scattering. The extent to which parameters such as the mirror surface roughness, dust size distribution, spatial distribution, and density may be determined using this approach is also discussed.

Kolodziejeczak, J. J.↗

NASA NTRS2000

Geometric Perturbations and Asymmetric vortex shedding About Slender Pointed Bodies

The flow about slender, pointed bodies can be characterized by different states with angle of attack. At moderate-to-high angles of attack (alpha approximately equals 40deg), a steady, asymmetric vortex pattern develops along the body, leading to a net lateral force. At higher angles of attack (alpha approximately equals 60deg), the aft-end of the body develops an unsteady von Karman shedding. As the angle of attack approaches 90deg, the entire body length exhibits a time-dependent vortex shedding pattern. The current work uses three-dimensional, thin-layer Navier-Stokes simulations to investigate the physical mechanisms of asymmetric vortex shedding at alpha = 40deg and alpha = 60deg. The development of an asymmetric vortex pattern via a convective instability mechanism is investigated using tip bumps, surface roughness, and tip curvature. It's found that surface roughness simulations can incite an asymmetric vortex state at alpha = 60deg which is consistent with the application of a tip bumps, and the experimentally observed flowfield. The unsteady von Karman vortex shedding on the aft portion of the body is also well resolved. The use of surface roughness did not incite a flow asymmetry at alpha = 40deg, and it was necessary to simulate tip curvature at this angle of attack in order to generate an asymmetric vortex state.

Murman, Scott M.↗

NASA NTRS2000

Geometric Perturbations and Asymmetric Vortex Shedding about Slender Pointed Bodies

The flow about slender, pointed bodies can be characterized by different states with angle of attack. At moderate-to-high angles of attack (alpha approx. = 40 deg.), a steady, asymmetric vortex pattern develops along the body, leading to a net lateral force. At higher angles of attack (alpha approx. = 60 deg.), the aft-end of the body develops an unsteady von Karman shedding. As the angle of attack approaches 90 deg., the entire body length exhibits a time-dependent vortex shedding pattern. The current work uses three-dimensional, thin-layer Navier-Stokes simulations to investigate the physical mechanisms of asymmetric vortex shedding at alpha = 40 deg. and alpha = 60 deg. The development of an asymmetric vortex pattern via a convective instability mechanism is investigated using tip bumps, surface roughness, and tip curvature. It's found that surface roughness simulations can incite an asymmetric vortex state at alpha = 60 deg. which is consistent with the application of a tip bump, and the experimentally observed flowfield. The unsteady von Karman vortex shedding on the aft. portion of the body is also well resolved. The use of surface roughness did not incite a flow asymmetry at alpha = 40 deg., and it was necessary to simulate tip curvature at this angle of attack in order to generate an asymmetric vortex state.

Murman, Scott M.↗

NASA NTRS2002

On the relationshop between polarimetric parameters and soil moisture

In this paper, we examine the relationship between polarimetric parameters and soil moisture. For example, the co-polarization ratio is independent of surface roughness to the first order of the small perturbation approximation. As surface roughness increases, it can be shown that the co-polarization ratio depends on the surface slope under the tilted Bragg approximation. The coupling of the surface roughness to the co-polarization ratio is theoretically investigated. An algorithm to compensate the surface slope effect will be discussed. We will also study other polarimetric parameters such as the average alpha angle and eigenvalues to understand their relationship with soil moisture.

polarimetric parameters soil moisture↗

NASA NTRS2013

Silicon Micromachined Microlens Array for THz Antennas

5 5 silicon microlens array was developed using a silicon micromachining technique for a silicon-based THz antenna array. The feature of the silicon micromachining technique enables one to microfabricate an unlimited number of microlens arrays at one time with good uniformity on a silicon wafer. This technique will resolve one of the key issues in building a THz camera, which is to integrate antennas in a detector array. The conventional approach of building single-pixel receivers and stacking them to form a multi-pixel receiver is not suited at THz because a single-pixel receiver already has difficulty fitting into mass, volume, and power budgets, especially in space applications. In this proposed technique, one has controllability on both diameter and curvature of a silicon microlens. First of all, the diameter of microlens depends on how thick photoresist one could coat and pattern. So far, the diameter of a 6- mm photoresist microlens with 400 m in height has been successfully microfabricated. Based on current researchers experiences, a diameter larger than 1-cm photoresist microlens array would be feasible. In order to control the curvature of the microlens, the following process variables could be used: 1. Amount of photoresist: It determines the curvature of the photoresist microlens. Since the photoresist lens is transferred onto the silicon substrate, it will directly control the curvature of the silicon microlens. 2. Etching selectivity between photoresist and silicon: The photoresist microlens is formed by thermal reflow. In order to transfer the exact photoresist curvature onto silicon, there needs to be etching selectivity of 1:1 between silicon and photoresist. However, by varying the etching selectivity, one could control the curvature of the silicon microlens. The figure shows the microfabricated silicon microlens 5 x5 array. The diameter of the microlens located in the center is about 2.5 mm. The measured 3-D profile of the microlens surface has a smooth curvature. The measured height of the silicon microlens is about 280 microns. In this case, the original height of the photoresist was 210 microns. The change was due to the etching selectivity of 1.33 between photoresist and silicon. The measured surface roughness of the silicon microlens shows the peak-to-peak surface roughness of less than 0.5 microns, which is adequate in THz frequency. For example, the surface roughness should be less than 7 microns at 600 GHz range. The SEM (scanning electron microscope) image of the microlens confirms the smooth surface. The beam pattern at 550 GHz shows good directivity.

Lee, Choonsup↗

NASA NTRS1996

A Numerical Simulation of Scattering from One-Dimensional Inhomogeneous Dielectric Random Surfaces

In this paper, an efficient numerical solution for the scattering problem of inhomogeneous dielectric rough surfaces is presented. The inhomogeneous dielectric random surface represents a bare soil surface and is considered to be comprised of a large number of randomly positioned dielectric humps of different sizes, shapes, and dielectric constants above an impedance surface. Clods with nonuniform moisture content and rocks are modeled by inhomogeneous dielectric humps and the underlying smooth wet soil surface is modeled by an impedance surface. In this technique, an efficient numerical solution for the constituent dielectric humps over an impedance surface is obtained using Green's function derived by the exact image theory in conjunction with the method of moments. The scattered field from a sample of the rough surface is obtained by summing the scattered fields from all the individual humps of the surface coherently ignoring the effect of multiple scattering between the humps. The statistical behavior of the scattering coefficient sigma(sup 0) is obtained from the calculation of scattered fields of many different realizations of the surface. Numerical results are presented for several different roughnesses and dielectric constants of the random surfaces. The numerical technique is verified by comparing the numerical solution with the solution based on the small perturbation method and the physical optics model for homogeneous rough surfaces. This technique can be used to study the behavior of scattering coefficient and phase difference statistics of rough soil surfaces for which no analytical solution exists.

Sarabandi, Kamal↗

NASA NTRS1980

Remote sensing of soil moisture content over bare fields at 1.4 GHz frequency

A simple method of estimating moisture content (W) of a bare soil from the observed brightness temperature (T sub B) at 1.4 GHz is discussed. The method is based on a radiative transfer model calculation, which has been successfully used in the past to account for many observational results, with some modifications to take into account the effect of surface roughness. Besides the measured T sub B's, the three additional inputs required by the method are the effective soil thermodynamic temperature, the precise relation between W and the smooth field brightness temperature T sub B and a parameter specifying the surface roughness characteristics. The soil effective temperature can be readily measured and the procedures of estimating surface roughness parameter and obtaining the relation between W and smooth field brightness temperature are discussed in detail. Dual polarized radiometric measurements at an off-nadir incident angle are sufficient to estimate both surface roughness parameter and W, provided that the relation between W and smooth field brightness temperature at the same angle is known. The method of W estimate is demonstrated with two sets of experimental data, one from a controlled field experiment by a mobile tower and the other, from aircraft overflight. The results from both data sets are encouraging when the estimated W's are compared with the acquired ground truth of W's in the top 2 cm layer. An offset between the estimated and the measured W's exists in the results of the analyses, but that can be accounted for by the presently poor knowledge of the relationship between W and smooth field brightness temperature for various types of soils. An approach to quantify this relationship for different soils and thus improve the method of W estimate is suggested.

Wang, J. R.↗

NASA NTRS1973

Comparison between photogrammetric and bistatic-radar slope frequency distributions

A comparison was made of the results for lunar surface roughness estimates and slope frequency distributions obtained by using photogrammetric techniques with those obtained by using bistatic radar. Three topics were discussed: (1) the form of the slope frequency distributions, (2) the change of roughness estimates of the lunar surface with scale, and (3) the magnitude of surface roughness.

Moore, H. J.↗

NASA NTRS1984

Cold-air performance of compressor-drive turbine of department of energy upgraded automobile gas turbine engine. 3: Performance of redesigned turbine

The aerodynamic performance of a redesigned compressor drive turbine of the gas turbine engine is determined in air at nominal inlet conditions of 325 K and 0.8 bar absolute. The turbine is designed with a lower flow factor, higher rotor reaction and a redesigned inlet volute compared to the first turbine. Comparisons between this turbine and the originally designed turbine show about 2.3 percentage points improvement in efficiency at the same rotor tip clearance. Two versions of the same rotor are tested: (1) an as cast rotor, and (2) the same rotor with reduced surface roughness. The effect of reducing surface roughness is about one half percentage point improvement in efficiency. Tests made to determine the effect of Reynolds number on the turbine performance show no effect for the range from 100,000 to 500,000.

Roelke, R. J.↗

NASA NTRS1993

X-ray evidence for particulate contamination on the AXAF VETA-1 mirrors

X-ray testing of the AXAF outer mirror pairs, in the VETA-1 configuration, reveals a point spread function (PSF) with unexpectedly large wings at low energies. Although the angular dependence in the wings of the PSF is close to that expected for diffractive scattering from surface roughness, the energy dependence differs substantially. Analyses of the observed X-ray PSF, images near ring focus, and single-quadrant images at conjugate focus suggest that the excess scattering observed at low X-ray energies results from diffractive scattering by relatively small grains (as small as a few tenths micrometer in radius). We develop a simple model for the contribution of scattering by particulates to the PSF. Merging this model with that for scattering by surface roughness, we fit the combined model to the observed energy-dependent PSF, in order to estimate parameters and associated uncertainties characterizing the grain-size distribution and the surface-roughness power spectral density. In particular, we find that the fractional coverage of the mirrors by particulates is approximately 1 x 10 exp -4 (for grain radii between 0.1 and 10 microns), and that the rms surface-roughness is approximately 0.7 nm (for spatial frequencies between 1/mm and 1000/mm).

O'Dell, S. L.↗