SEARCH · Engineering Papers

Results for “surface oxidation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

All sources NASA NTRS DOE OSTI

DOE OSTI2022

Corrosion resistance of high nickel alloys in solar salt at 600 °C for up to 4000 h

This study focuses on the time dependent performance of the corrosion resistance of IN625, H230 and 740H alloys in the solar salt (60 wt% NaNO3, 40 wt% KNO3, at 600 °C) for up to 4000 h. Alloy IN625 showed the lowest mass change with parabolic oxidation kinetics that tends to stabilize with exposure time. Both 740H and H230 alloys deviated from the parabolic oxidation behavior beyond the 3000 h of exposure. Alloy 740H showed the highest mass loss due to the nonuniform surface oxidation and the high chromium dissolution rate. Internal oxidation was noticed with Alloy H230 due to the high tungsten concentrations.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Dynamic Behavior of Platinum Atoms and Clusters in the Native Oxide Layer of Aluminum Nanocrystals

Strong metal–support interactions (SMSIs) are well-known in the field of heterogeneous catalysis to induce the encapsulation of platinum (Pt) group metals by oxide supports through high temperature H 2 reduction. However, demonstrations of SMSI overlayers have largely been limited to reducible oxides, such as TiO 2 and Nb 2 O 5 . In this report we show that the amorphous native surface oxide of plasmonic aluminum nanocrystals (AlNCs) exhibits SMSI-induced encapsulation of Pt following reduction in H 2 in a Pt structure dependent manner. Reductive treatment in H 2 at 300 °C induces the formation of an AlO x SMSI overlayer on Pt clusters, leaving Pt single-atom sites (Ptiso) exposed available for catalysis. The remaining exposed Pt iso species possess a more uniform local coordination environment than has been observed on other forms of Al 2 O 3 , suggesting that the AlO x native oxide of AlNCs presents well-defined anchoring sites for individual Pt atoms. This observation extends our understanding of SMSIs by providing evidence that H 2 -induced encapsulation can occur for a wider variety of materials and should stimulate expanded studies of this effect to include nonreducible oxides with oxygen defects and the presence of disorder. It also suggests that the single-atom sites created in this manner, when combined with the plasmonic properties of the Al nanocrystal core, may allow for site-specific single-atom plasmonic photocatalysis, providing dynamic control over the light-driven reactivity in these systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Effect of Ambient Organic Acids on the Water Structure at ${\rm TiO}_{2}$ Interfaces

A molecular-level understanding of the effects of ambient organic compounds on the wettability of titanium dioxide ( ${\rm TiO}_{2}$ ) surfaces is relevant to many of its energy-related and environmental applications. Herein, we focus on two common atmospheric carboxylic acids, formic and acetic acid, and characterize their adsorption/ desorption at the aqueous interfaces of anatase and rutile ${\rm TiO}_{2}$ using molecular dynamics with an ab initio deep neural network potential. Our simulations show that these acids prefer to be localized in the interfacial water layers close to the ${\rm TiO}_{2}$ surface where they are stabilized by the interaction/exchange of their acid proton with a surface oxygen, rather than chemisorb at the surface Ti sites by displacing the adsorbed water. Notably, these acids make the surface of anatase hydrophobic, whereas the larger fraction of adsorbed water dissociation can offset their effect on rutile. Furthermore, these results provide a picture where carboxylic acids control the wettability of ${\rm TiO}_{2}$ largely through acid-base chemistry at the interface rather than chemisorption on the oxide surface, a finding that can help improve the design of self-cleaning surfaces and photocatalytic devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1981

Application of surface analysis to solve problems of wear

Results are presented for the use of surface analytical tools including field ion microscopy, Auger emission spectroscopy analysis (AES), cylindrical mirror Auger analysis and X-ray photoelectron spectroscopy (XPS). Data from the field ion microscope reveal adhesive transfer (wear) at the atomic level with the formation of surface compounds not found in the bulk, and AES reveals that this transfer will occur even in the presence of surface oxides. Both AES and XPS reveal that in abrasive wear with silicon carbide and diamond contacting the transition metals, the surface and the abrasive undergo a chemical or structural change which effects wear. With silicon carbide, silicon volatilizes leaving behind a pseudo-graphitic surface and the surface of diamond is observed to graphitize.

Buckley, D. H.↗

NASA NTRS2000

Quantitative Analysis of Charge Injection and Discharging of Si Nanocrystals and Arrays by Electrostatic Force Microscopy

NASA requirements for computing and memory for microspacecraft emphasize high density, low power, small size, and radiation hardness. The distributed nature of storage elements in nanocrystal floating-gate memories leads to intrinsic fault tolerance and radiation hardness. Conventional floating-gate non-volatile memories are more susceptible to radiation damage. Nanocrystal-based memories also offer the possibility of faster, lower power operation. In the pursuit of filling these requirements, the following tasks have been accomplished: (1) Si nanocrystal charging has been accomplished with conducting-tip AFM; (2) Both individual nanocrystals on an oxide surface and nanocrystals formed by implantation have been charged; (3) Discharging is consistent with tunneling through a field-lowered oxide barrier; (4) Modeling of the response of the AFM to trapped charge has allowed estimation of the quantity of trapped charge; and (5) Initial attempts to fabricate competitive nanocrystal non-volatile memories have been extremely successful.

Bell, L. D.↗

NASA NTRS1985

Ellipsometric surface analysis of wear tracks produced by different lubricants

A scanning ellipsometer with high spatial resolution was used to analyze wear tracks generated on M-50 surfaces operated in several lubricant formulations. These formulations included a pure ester base stock of trimethyol propane triheptanoate with additives of either benzotriazole (BTZ), dioctyldiphenylamine (DODPA), or tricresylphosphate (TCP). Results indicated that BTZ and TCP produced patchy oxide surface films consisting mainly of Fe304. DOPDA produced a much more uniform oxide film. These findings may explain the tendency of lubricant formulations containing TCP to scuff more readily than those containing only antioxidants.

Lauer, J. L.↗

DOE OSTI2022

Alternate Methods for Cleaning Zirconium Plate

The United States High Performance Research Reactor Conversion Program identified the need to transition from highly enriched uranium fuel to lowly enriched uranium fuel for high power research and civil reactors. One of the fuel configurations selected for these reactors was a uranium (U) foil alloyed with 10% molybdenum (Mo). The U-10Mo fuel foil was then covered with a zirconium (Zr) interlayer and pressed into an aluminum cladding. Idaho National Laboratory prescribed a need to remove surface oxidation on the Zr prior to bonding it with U-10Mo fuel foil. To determine the best method of oxidation removal, a variety of polishing methods, including hand polishing with a diamond paste or Scotch-Brite™ pads, mechanically wet-polishing with abrasive belts, and chemical etching with hydrofluoric/nitric acid mixtures, were investigated on pre-polished Zircaloy 702 sheets purchased directly from the manufacturer. No change in surface roughness was detected using any of these methods relative to the as-received material. In fact, scanning electron microscopy detected grit from hand polishing with Amplex Grade 30 waste soluble diamond paste and Scotch-Brite™ pads. Visible staining was found, and fluorine detected via X-ray photoelectron spectroscopy on the flash etching samples. These contaminants were not seen on the as-received material. In addition to the need to remove the oxide layer on the Zr prior to co-rolling, there are concerns that the Neolube debonding agent on the co-rolling can may contaminate the Zr surface after co-rolling. The experimental results found that zirconium in contact with Neolube coated steel plates was easily cleaning with ethanol wiping after heat treated and no carbide inclusions remained on the surface. Overall, all cleaning methods tested did not significantly change the surface roughness of the plates or reduce the oxide layer present on the zirconium. Carbon was found on all the samples, before and after cleaning, except for the flash etch samples which detected fluorine instead. The insignificant changes seen in the cleaned plates relative to the as received plates question the need for cleaning prior to rolling. Further investigation in the requirements for cleaning at this step is recommended. Current methods for cleaning the surface after hot rolling with alcohol appear sufficient. After hot rolling, if Neolube does peel off the can and onto the zirconium coated foil surface, a dry abrasive or diamond paste polish is not recommended due to the chance of abrasive being embedded into the surface. However, the ability of an etchant to lift the lubricant off the zirconium surface indicates that a spot etch method could work to clean specific spots where Neolube is present, if the need arises.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Finding a needle in a haystack: quantitative HERFD-XRF imaging and HERFD-XANES characterization of trace platinum in gold solidi from the Late Roman and Byzantine Empires

High-Energy Resolution Fluorescence Detection X-Ray Fluorescence (HERFD-XRF) imaging and HERFD X-ray Absorption Near Edge Structure (XANES) spectroscopy are used to quantify and characterize trace platinum (Pt) in gold solidi from the Late Roman and Byzantine Empires. Historically, the elemental analysis of coins has been pivotal in distinguishing authentic artifacts from forgeries, elucidating minting practices, and understanding economic shifts. Notably, a new gold source with high platinum content appeared in the fourth century CE, transforming the Roman economy. Traditional methods struggled to detect platinum due to the overwhelming gold matrix. Here, this study demonstrates the effectiveness of HERFD techniques in resolving this challenge. Three gold solidi, minted between 654 and 659 CE, were analyzed alongside reference gold materials with known Pt concentrations. The HERFD-XRF imaging revealed spatial distributions of platinum, highlighting non-uniformities within the coins. Additionally, HERFD-XANES spectroscopy identified the oxidation states and chemical speciation of platinum. Results demonstrate that platinum in the solidi primarily exists as metallic Pt, with some surface oxidation. The findings align with previous measurements but reveal higher Pt concentrations and significant inhomogeneities. This research confirms the reliability of HERFD methods for quantifying trace elements and provides new insights into the raw material sources and minting techniques of ancient gold coins. The non-destructive nature of this approach allows for extensive analyses, offering valuable data for historical, economic, and archaeological studies. This innovative application of HERFD-XRF imaging and XANES in cultural heritage research underscores the potential for detailed material characterization and conservation, enhancing our understanding of ancient economies and trade patterns.

Van Loon, Lisa L.↗

DOE OSTI2026

Emissivity measurements of CuCrZr alloy

The Facility for Rare Isotope Beams (FRIB) heavy-ion accelerator, in user operation since 2022, produces rare isotope beams via interactions of high-intensity stable ion beams with a graphite production target. Approximately 20–40% of the primary beam power is deposited in the target, while the remaining 60–80% is absorbed by the beam dump. The minichannel beam dump (MCBD), currently operated at 20 kW and designed for operation up to 50 kW, uses CuCrZr alloy absorber plates. Thermal validation and thermal cycling tests of the MCBD were conducted at the Applied Research Laboratory (ARL) at Pennsylvania State University. Temperature measurements were obtained from an infrared (IR) camera. Since accurate temperature determination requires reliable emissivity values, the emissivity of CuCrZr was measured using the IR camera validated against thermocouple reference temperatures up to approximately 650 °C. The measurements were conducted under a vacuum level of approximately 10 -5 torr to minimize emissivity variations due to surface oxidation. The emissivity of CuCrZr was determined to be 0.057 ± 0.009 using a constant fit to the measured data over the surface temperature range from 100–650 °C.

Accelerator Subsystems and Technologies↗

DOE OSTI2021

Mg x Zn 1−x O contact to CuGa 3 Se 5 absorber for photovoltaic and photoelectrochemical devices

Abstract CuGa 3 Se 5 is a promising candidate material with wide band gap for top cells in tandem photovoltaic and photoelectrochemical (PEC) devices. However, traditional CdS contact layers used with other chalcopyrite absorbers are not suitable for CuGa 3 Se 5 due to the higher position of its conduction band (CB) minimum. Mg x Zn 1− x O (MZO) is a transparent oxide with adjustable band gap and CB position as a function of magnesium composition, but its direct application is hindered by CuGa 3 Se 5 surface oxidation. Here, MZO is investigated as a contact (n-type ‘buffer’ or ‘window’) material to CuGa 3 Se 5 absorbers pretreated in Cd 2+ solution, and an onset potential close to 1 V vs reversible hydrogen electrode in 10 mM hexaammineruthenium (III) chloride electrolyte is demonstrated. The Cd 2+ surface treatment changes the chemical composition and electronic structure of the CuGa 3 Se 5 surface, as demonstrated by photoelectron spectroscopy measurements. The performance of CuGa 3 Se 5 absorber with Cd 2+ treated surface in the solid-state test structure depends on the Zn/Mg ratio in the MZO layer. The measured open circuit voltage of 925 mV is promising for tandem PEC water splitting with CuGa 3 Se 5 /MZO top cells.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Corrosion Compatibility of Stainless Steels and Nickel in Pyrolysis Biomass-Derived Oil at Elevated Storage Temperatures

Corrosion compatibility of stainless steels and nickel (Ni200) was assessed in fast pyrolysis bio-oil produced from pyrolysis of high ash and high moisture forest residue biomass. Sample mass change, ICP-MS and post-exposure electron microscopy characterization was used to investigate the extent of corrosion. Among the tested samples, type 430F and type 316 stainless steels (SS430F and SS316) and Ni200 (~98.5% Ni) showed minimal mass changes (less than 2 mg∙cm−2) after the bio-oil exposures at 50 and 80 °C for up to 168 h. SS304 was also considered to be compatible in the bio-oil due to its relatively low mass change (1.6 mg∙cm−2 or lower). SS410 samples showed greater mass loss values even after exposures at a relatively low temperature of 35 °C. Fe/Cr values from ICP-MS data implied that Cr enrichment in stainless steels would result in a protective oxide layer associated with corrosion resistance against the bio-oil. Post exposure characterization showed continuous and uniform Cr distribution in the surface oxide layer of SS430F, which showed a minimal mass change, but no oxide layer on a SS430 sample, which exhibited a significant mass loss.

09 BIOMASS FUELS↗

NASA NTRS1985

Fluidized reduction of oxides on fine metal powders without sintering

In the process of reducing extremely fine metal particles (av. particle size or = 1000 angstroms) covered with an oxide layer, the metal particles are fluidized by a gas flow contg. H, heated, and reduced. The method uniformly and easily reduces surface oxide layers of the extremely fine metal particles without causing sintering. The metal particles are useful for magnetic recording materials, conductive paste, powder metallurgy materials, chem. reagents, and catalysts.

Hayashi, T.↗

DOE OSTI2021

CO 2 electro-reduction on Cu 3 P: Role of Cu(I) oxidation state and surface facet structure in C 1 -formate production and H 2 selectivity

We report the catalytic activity and mechanism of copper(I) phosphide, Cu 3 P, with predominant [00Ι] facet exposure for the electrochemical reduction of CO 2 (CO 2 RR) to formic acid. Crystalline nanosheets of this compound that show a preferential [00Ι] facet orientation exhibit undiminished CO 2 RR activity after 16 hours with full retention of crystal structure and surface chemical speciation and no detectable corrosion. In contrast to the range of products formed on Cu metal, CuO, and Cu 2 O, the CO 2 RR on Cu 3 P [00Ι] produces mainly hydrogen and formate as the sole carbon product in KHCO 3 electrolyte. Analysis of the Cu 3 P [00Ι] facet by HAADF-STEM was used to determine the surface lattice structure, while both XPS and Auger spectroscopies were used to determine the surface chemical speciation from the kinetic energies of ionized electrons. The presented analysis identifies isolated trigonal CuP 3 sites on the Cu 3 P[00Ι]-Cu 3 P 3 terminated surface and the Cu(I) oxidation state as precursor to the active catalyst. The CO 2 RR selectivity to formate and the higher turnover rate for H 2 production on the [00Ι] facet allows a structure-activity analysis and chemical mechanism to be proposed. Formation of a surface hydride at isolated *H-CuP 3 sites is proposed as the catalytic site in forming both H 2 and formate, while the long Cu—Cu separation retards forming C-C coupling products. In conclusion, these results disprove previously published claims of Cu(I) oxidation state as a sufficient criterion to promote CO 2 RR to C 2+ products, show that stronger bonded hydrides, *H-CuP 3 on Cu 3 P, favor production of the C1 product formate over all other carbon products, and predict that stronger formate binding (bidentate) is needed for CO 2 RR currents to compete with H 2 production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

Investigation of the Surface Chemistry of Magnesium and Magnesium Alloy Powders

Magnesium (Mg) and Mg alloy powders are generally difficult to sinter at atmospheric pressure in inert atmospheres purportedly due to the presence of powder particle surface oxide layers. To better understand sintering of Mg and Mg alloy powders, x-ray photoelectron spectroscopy (XPS) was performed to characterize the surface chemistry of gas atomized pure Mg and Mg alloys AZ91D and WE43 powders. These results are used to quantitatively determine the surface chemistry of these powders. Additionally, equilibrium thermodynamic modeling of these Mg/Mg alloys materials exposed to oxygen down to part per billion concentrations are presented for relative comparison to experimental XPS results. Analysis of these results are intended to improve sintering of Mg and Mg alloy powder materials through more quantitative knowledge of powder surface chemistry.

25 ENERGY STORAGE↗

DOE OSTI2021

Microstructural basis for improved corrosion resistance of laser surface processed AZ31 Mg alloy

Despite their excellent strength to weight ratio, wider use of Mg alloys for light weighting applications is limited by their poor corrosion resistance, especially in chloride ion-containing environments. The present study shows improved corrosion resistance imparted by laser surface processing (LSP) of a commercial AZ31 (Mg-3Al-1Zn) alloy. Nanosecond laser processing at three different power settings was carried out on the surface of a 1 mm thick rolled AZ31 sheet. Corrosion testing based on ASTM B117 method and several other electrochemical tests indicates substantial enhancement of corrosion resistance in LSP-treated AZ31. The underlying reason behind improved corrosion resistance of LSP-AZ31 surface has been identified using a variety of characterization tools (SEM, TEM, XPS). Formation of a ~0.5 µm thick mixed metal (Mg, Al) oxide surface film together with refinement in the size and number density of Al-Mn intermetallic particles appear to be playing a major role towards improved corrosion resistance after LSP treatment of AZ31 alloy.

Jana, Saumyadeep↗

NASA NTRS1990

Surface studies on scandate cathodes and synthesized scandates

Auger, ESCA, electron emission, evaporation, and desorption measurements were made on three different types of scandate surfaces. They are: (1) an impregnated top layer scandate cathode, (2) an unimpregnated top layer scandate cathode with a deposited barium or barium oxide adsorbate surface layer, and (3) a synthesized scandate surface, which replicates a scandate cathode surface. The purpose of these experiments was to determine the role that Sc2O3 plays in making the scandate cathode a more copious electron emitter than the conventional impregnated-type cathode. The synthesized scandate surface experiments consisted of depositing multilayer scandium on a tungsten surface, oxidizing the scandium, and then depositing either Ba or BaO on the scandium oxide surface. The results of these measurements showed that the low work function portions of the thin-film scandate cathode are where the Sc2O3 is the substrate and BaO is the adsorbate.

Lesny, Gary↗

NASA NTRS2003

Laminar Soot Processes (Lsp) Experiment: Findings From Ground-Based Measurements

Processes of soot formation and oxidation must be understood in order to achieve reliable computational combustion calculations for nonpremixed (diffusion) flames involving hydrocarbon fuels. Motivated by this observation, the present investigation extended earlier work on soot formation and oxidation in laminar jet ethylene/air and methane/oxygen premixed and acetylene-nitrogen/air diffusion flames at atmospheric pressure in this laboratory, emphasizing soot surface growth and early soot surface oxidation in laminar diffusion flames fueled with a variety of hydrocarbons at pressures in the range 0.1 - 1.0 atm.

Kim, C. H.↗

DOE OSTI2023

Mesoporous CuFe 2 O 4 Photoanodes for Solar Water Oxidation: Impact of Surface Morphology on the Photoelectrochemical Properties**

Abstract Metal oxide‐based photoelectrodes for solar water splitting often utilize nanostructures to increase the solid‐liquid interface area. This reduces charge transport distances and increases the photocurrent for materials with short minority charge carrier diffusion lengths. While the merits of nanostructuring are well established, the effect of surface order on the photocurrent and carrier recombination has not yet received much attention in the literature. To evaluate the impact of pore ordering on the photoelectrochemical properties, mesoporous CuFe 2 O 4 (CFO) thin film photoanodes were prepared by dip‐coating and soft‐templating. Here, the pore order and geometry can be controlled by addition of copolymer surfactants poly(ethylene oxide)‐ block ‐poly(propylene oxide)‐ block ‐poly(ethylene oxide) (Pluronic® F‐127), polyisobutylene‐ block ‐poly(ethylene oxide) (PIB‐PEO) and poly(ethylene‐ co ‐butylene)‐ block ‐poly(ethylene oxide) (Kraton liquid™‐PEO, KLE). The non‐ordered CFO showed the highest photocurrent density of 0.2 mA/cm 2 at 1.3 V vs. RHE for sulfite oxidation, but the least photocurrent density for water oxidation. Conversely, the ordered CFO presented the best photoelectrochemical water oxidation performance. These differences can be understood on the basis of the high surface area, which promotes hole transfer to sulfite (a fast hole acceptor), but retards oxidation of water (a slow hole acceptor) due to electron‐hole recombination at the defective surface. This interpretation is confirmed by intensity‐modulated photocurrent (IMPS) and vibrating Kelvin probe surface photovoltage spectroscopy (VKP‐SPS). The lowest surface recombination rate was observed for the ordered KLE‐based mesoporous CFO, which retains spherical pore shapes at the surface resulting in fewer surface defects. Overall, this work shows that the photoelectrochemical energy conversion efficiency of copper ferrite thin films is not just controlled by the surface area, but also by surface order.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗