Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “property”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Enhanced Thermoelectric Properties for PEDOT:PSS/Undoped Ge Thin-Film Bilayered Heterostructures

Modulation doping is one of the strategies to improve thermoelectric power factors of nanocomposites and thin-film bilayered heterostructures by effectively increasing electrical conductivity. Here, it is reported that thin-film heterostructures of heavily doped p-type organic conducting polymer, poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) and undoped thin-film Ge can enhance thermoelectric power factor by modulation doping. The maximum power factor and Seebeck coefficient of the bilayered heterostructures are 154 µW m -1 K -2 and 398 µV K -1 , respectively, corresponding to 47-fold and 41-fold increases compared to those of bulk PEDOT:PSS and 64-fold increase compared to power factor of undoped Ge. The enhancements in power factor and Seebeck coefficient are quantitatively described by the hole transfer from PEDOT:PSS to Ge, which takes into account the band alignment at the interface detected by Kraut's method. Agreement between the simulation and experiment results also implies predictability of thermoelectric performances of nanoscale bilayered heterostructures in general, when band offset, Fermi level, and individual electronic properties are available. This work can be further extended to predict performance of other nanoscale combinations of thermoelectric and other electronic materials in general.

charge transport↗

Studies on Thermoelectric Properties of n-type Polycrystalline SnSe 1- x S x by Iodine Doping

Iodine-doped n-type SnSe polycrystalline by melting and hot pressing is prepared. The prepared material is anisotropic with a peak ZT of ≈0.8 at about 773 K measured along the hot pressing direction. This is the first report on thermoelectric properties of n-type Sn chalcogenide alloys. With increasing content of iodine, the carrier concentration changed from 2.3 × 1017 cm-3 (p-type) to 5.0 × 1015 cm-3 (n-type) then to 2.0 × 1017 cm-3 (n-type). The decent ZT is mainly attributed to the intrinsically low thermal conductivity due to the high anharmonicity of the chemical bonds like those in p-type SnSe. By alloying with 10 at% SnS, even lower thermal conductivity and an enhanced Seebeck coefficient were achieved, leading to an increased ZT of ≈1.0 at about 773 K measured also along the hot pressing direction.

36 MATERIALS SCIENCE↗

Achieving High‐Performance and 2000 h Stability in Anion Exchange Membrane Fuel Cells by Manipulating Ionomer Properties and Electrode Optimization

The primary function of the ionomers that are incorporated into fuel cell electrode catalyst layers is to provide pathways for ion transport between the catalyst active sites and the electrolyte. This is influenced by many variables, including the ion-exchange capacity, water uptake, and molecular weight. In anion exchange membrane fuel cells (AEMFCs), controlling ionomer water uptake is particularly important and tailoring this property in each electrode is an important consideration when looking to maximize cell performance. In this study, three poly(norbornene) tetrablock copolymer ionomers with a range of physical properties are synthesized and incorporated into AEMFC anode and cathode electrodes. Systematic electrode engineering with these ionomers allows the peak power density to be increased by 100% (1.6 W cm -2 → 3.2 W cm -2 ) and the current density at 0.2 V to be increased by 59% (5.9 A cm -2 → 9.4 A cm -2 ). Moreover, the top-performing electrode configuration is tested in an operating AEMFC at the US Department of Energy defined current density of 600 mA cm -2 for 2000 h, showing a record-low voltage decay rate of 15.36 µV h -1 – only 3.65% –a over 2000 h. Here, this work sets a new bar for AEMFCs, reporting the best combination of performance and durability of any AEMFC to date.

08 HYDROGEN↗

Polypeptoid polymers: Synthesis, characterization, and properties

Polypeptoids, a class of peptidomimetic polymers, have emerged at the forefront of macromolecular and supramolecular science and engineering as the technological relevance of these polymers continues to be demonstrated. The chemical and structural diversity of polypeptoids have enabled access to and adjustment of a variety of physicochemical and biological properties (eg, solubility, charge characteristics, chain conformation, HLB, thermal processability, degradability, cytotoxicity and immunogenicity). These attributes have made this synthetic polymer platform a potential candidate for various biomedical and biotechnological applications. Furthermore, this review will provide an overview of recent development in synthetic methods to access polypeptoid polymers with well–defined structures and highlight some of the fundamental physicochemical and biological properties of polypeptoids that are pertinent to the future development of functional materials based on polypeptoids.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Understanding the Photocatalytic Properties of Pt/CeO x /TiO 2 : Structural Effects on Electronic and Optical Properties

Ceria-titania interfaces play a crucial role in different chemical processes but are especially promising for the photocatalytic splitting of water using light in the visible wavelength region when Pt is added to the system. Yet, the complexity of this hierarchical structure hampers the study of the origin of its outstanding properties. In this article, the structural, electronic and optoelectronic properties of CeO 2 /TiO 2 systems containing 1D, 2D, and 3D particles of ceria are analyzed by means of density functional calculations. Adsorption sites and vacancy effects have been studied to model Pt adsorption. Density of states calculations and absorption spectra simulations explain the behavior of these systems. Conclusively, these models are used for the screening of other metals that can be combined with this heterostructure to possibly find more efficient water splitting photocatalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electrochemically Controlled Ion‐exchange Property of Carbon Nanotubes/Polypyrrole Nanocomposite in Various Electrolyte Solutions

Abstract The electrochemically controlled ion‐exchange properties of multi‐wall carbon nanotube (MWNT)/electronically conductive polypyrrole (PPy) polymer composite in the various electrolyte solutions have been investigated. The ion‐exchange behavior, rate and capacity of the electrochemically deposited polypyrrole with and without carbon nanotube (CNT) were compared and characterized using cyclic voltammetry (CV), chronoamperometry (CA), electrochemical quartz crystal microbalance (EQCM), X‐ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). It has been found that the presence of carbon nanotube backbone resulted in improvement in ion‐exchange rate, stability of polypyrrole, and higher anion loading capacity per PPy due to higher surface area, electronic conductivity, porous structure of thin film, and thinner film thickness providing shorter diffusion path. Chronoamperometric studies show that electrically switched anion exchange could be completed more than 10 times faster than pure PPy thin film. The anion selectivity of CNT/PPy film is demonstrated using X‐ray photoelectron spectroscopy (XPS).

Choi, Daiwon↗

Understanding the structure–property relationships of the ferroelectric to relaxor transition of the (1-x)BaTiO3–(x)BiInO3 lead-free piezoelectric system

A structural and electromechanical investigation has been performed on (1-x)BaTiO 3 –(x)BiInO 3 in the region 0.03 ≤ x ≤ 0.12. A gradual structural phase transition has been observed where the structure changes from tetragonal (P4mm) and passes through two regions of coexisting phases: (1) P4mm + R3m in the range 0.03 ≤ x ≤ 0.075 and (2) Pm$\bar{3}$m + R3m for 0.10 ≤ x ≤ 0.12. The properties also transition from ferroelectric (x ≤ 0.03) to relaxor ferroelectric (x ≥ 0.05) as the dielectric permittivity maximum becomes temperature and frequency dependent. This transition was also confirmed via polarization-electric field measurements as well as strain-electric field measurements. At the critical composition of x = 0.065, a moderate strain of ~0.104% and an effective piezoelectric coefficient (d$*\atop{33}$) of 260 pm/V were observed. Finally, the original purpose of this study was to demonstrate the polarization extension mechanism as predicted in the literature, but due to the ferroelectric to relaxor transition, this mechanism was not found to be present in this system. However, this demonstrates that BaTiO 3 -based lead-free ceramics could be modified to obtain enhanced electromechanical properties for actuator applications.

36 MATERIALS SCIENCE↗

The effect of interstitial carbon on the mechanical properties and dislocation substructure evolution in Fe 40.4 Ni 11.3 Mn 34.8 Al 7.5 Cr 6 high entropy alloys

A systematic study of the effects of up to 1.1 at. % carbon on the mechanical properties and evolution of the dislocation substructure in a series of a high entropy alloys (HEA) based on Fe40.4Ni11.3Mn34.8Al7.5Cr6 is presented. Transmission electron microscopy (TEM), synchrotron X-ray diffraction (XRD) and atom probe tomography (APT) were used to show that all the alloys are single-phase f.c.c. random solid solutions. The lattice constant, determined from synchrotron XRD measurements, increases linearly with increasing carbon concentration, which leads to a linear relationship between the yield strength and the carbon concentration. The dislocation substructures, as determined by a TEM, show a transition from wavy slip to planar slip and, at higher strains, and from cell-forming structure (dislocations cells, cell blocks and dense dislocation walls) to non-cell forming structure (Taylor lattice, microbands and domain boundaries) with the addition of carbon, features related to the increase in lattice friction stress. The stacking fault energy (measured via weak-beam imaging of the separation of dislocation partials) decreases with increasing carbon content, which also contributes to the transition from wavy slip to planar slip. The formation of non-cell forming structure induced by carbon leads to a high degree of strain hardening and a substantial increase in the ultimate tensile strength. The consequent postponement of necking due to the high strain hardening, along with the plasticity accommodation arising from the formation of microbands and domain boundaries, result in an increase of ductility due to the carbon addition. (C) 2016 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Dislocation structures↗

Individual phase constitutive properties of a TRIP-assisted QP980 steel from a combined synchrotron X-ray diffraction and crystal plasticity approach

Microstructure-based constitutive models for multiphase steels require accurate constitutive properties of the individual phases for component forming and performance simulations. We address this requirement with a combined experimental/theoretical methodology which determines the critical resolved shear stresses and hardening parameters of the constituent phases in QP980, a TRIP assisted steel subject to a two-step quenching and partitioning heat treatment. High energy X-Ray diffraction (HEXRD) from a synchrotron source provided the average lattice strains of the ferrite, martensite, and austenite phases from the measured volume during in situ tensile deformation. The HEXRD data was then input to a computationally efficient, elastic-plastic self-consistent (EPSC) crystal plasticity model which estimated the constitutive parameters of different slip systems for the three phases via a trial-and-error approach. The EPSC-estimated parameters are then input to a finite element crystal plasticity (CPFE) model representing the QP980 tensile sample. The predicted lattice strains and global stress versus strain curves are found to be 8% lower that the EPSC model predicted values and from the HEXRD measurements, respectively. This discrepancy, which is attributed to the stiff secant assumption in the EPSC formulation, is resolved with a second step in which CPFE is used to iteratively refine the EPSC-estimated parameters. Remarkably close agreement is obtained between the theoretically-predicted and experimentally derived flow curve for the QP980 material.

Hu, X. H. (ORCID:0000000277355091)↗

Fuel Property Effects on Knock Propensity and Thermal Efficiency in a Direct-Injection Spark-Ignition Engine

Engine knock remains one of the major barriers to further improvement in thermal efficiency of Direct-Injection Spark-Ignition (DISI) engines. While Research Octane Number and Motor Octane Number are often used as standard rating methods for knock resistance of fuels, the impacts of other fuel properties on knock propensity in modern engines such as heat of vaporization (HoV) and laminar flame speed (LFS) require better understanding in order to co-optimize fuels and engine designs to achieve higher thermal efficiency and lower CO2 emission. In the present study, computational fluid dynamics (CFD) is used to model a boosted DISI engine with a focus on knock prediction and fuel property effects. A level-set G-equation model is employed to capture turbulent premixed combustion, and is coupled with a transported Livengood-Wu (L-W) integral approach to predict autoignition in the unburnt region. A criterion associated with the L-W integral is developed to accurately predict knock onset and knock-limited spark-advance. This model is then applied to a sensitivity analysis of HoV and LFS on knock tendency and thermal efficiency. The pressure-temperature trajectory framework is applied and extended to study the fuel effects on auto-ignition process in the engine. An existing efficiency-based merit function, which is derived from experiments for boosted SI engines, is evaluated and improved based on the current CFD results.

DISI↗

Microstructure and magnetic properties of (001) textured L1(0) FePt films on amorphous glass substrate

L1(0) FePt thin films with an island-like morphology and magnetic perpendicular anisotropy were grown at low temperature (300 < T-dep< 375 degrees C) by magnetron sputtering on Hoya glass substrates using a 30-nm thick Cr (2 0 0) underlayer. An MgO buffer layer with a thickness of 2 nm was used to inhibit the diffusion from the Cr underlayer and promote the growth of (0 0 1) oriented L1(0) FePt films by inducing an in-plane lattice distortion. By varying the substrate temperature and the Ar sputter pressure (3.5 < P-Ar< 15 mTorr) during the deposition, the degree of chemical order, the microstructure and the magnetic properties were tuned and the best properties in term of squareness ratio (M-r/M-s similar to 0.95) and coercive field (H-c similar to 14 kOe) were observed for films deposited at T-dep = 350 degrees C and P-Ar= 5 mTorr, due to the appearance of a tensile strain, which favors the perpendicular anisotropy. The analysis of the angular dependence of remanent magnetization curves on the optimized sample suggests that the magnetization reversal is highly incoherent due to the inter-island interactions. Our results provide useful information on the low temperature growth of FePt films with perpendicular anisotropy onto glass substrates, which are relevant for a variety of technological applications, such as magnetic recording and spintronic devices. (C) 2015 Elsevier B.V. All rights reserved.

Speliotis, T↗