Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “producible well”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Cummins Electric Truck with Range-Extending Engine (ETREE) Project (Final Technical Report)

The Cummins Electric Truck with Range Extending Engine (ETREE) program designed, developed, and demonstrated a range extending electric vehicle that employs an electrified propulsion system installed in a class 6 commercial vehicle (Peterbilt 220). This project was relevant to industry and the greater public because at the time of the project there were two keys to widespread electrified commercial vehicle adoption yet to be realize: 1) For pure electrified vehicle adoption, battery improvements are needed: Cost must decrease, and energy density must increase. 2) Electric vehicles must overcome fleet operator risks such as: operations in cold climates, hilly terrain, or where majority of conventional trucks are replaced with electrified vehicles. In the near to medium term these adoption hurdles were address by the objectives of this project. A plug-in hybrid vehicle that could be operated in all electric mode for most of its workday optimizing the use of grid energy with the ability to supplement energy demand with the onboard range extending engine. This project’s architecture provided ability to match a conventional class 6 commercial vehicle range and performance characteristics prior to the ubiquitous adoption of battery electric vehicle charging infrastructure as well. Additionally, the vehicles produced as part of this project can be considered a prototype for a commercially viable heavily electrified commercial vehicle because most of the physical hardware used for the project is commercially available in the market today. The ETREE program met its main objectives and demonstrated 65% fuel consumption reduction as compared to a conventional class 6 vehicle while meeting performance and range expectations. This was achieved by drawing upon the strengths of the assembled team: Cummins, PACCAR, the Ohio State University, Argonne National Laboratory and the National Renewable Energy Laboratory.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2021

Fission Induced Radiolysis of Uranyl Sulfate Solutions

At Argonne National Laboratory, an experimental pilot facility is being tested for the production of the medical isotope molybdenum-99 ( 99 Mo). AMORE (Argonne Molybdenum Research Experiment) is an experimental pilot facility in which a 40 MeV electron beam from the LINAC strikes a depleted uranium (DU) target. The target generates high energy neutrons, which are thermalized in an 18-liter uranyl sulfate solution of low enriched uranium (LEU). Thermalized neutrons fission the uranium-235 ( 235 U) to produce 99 Mo as well as many other fission products. The 99 Mo is recovered from the uranium solution and purified. The goal of our work is to reduce the use of highly enriched uranium (HEU) for the production of this isotope.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2024

Dust Formation and Destruction in Core Collapse Supernovae Explosions [Dissertation]

Dust is a crucial component of the Interstellar Medium (ISM) and an important driver in many astrophysical processes. Dust formed from evolved stars increases the metallicity of the ISM, enriching it with heavier elements. Dust makes up the source material of collapsing clouds in the ISM leading to stellar and galactic formation. The stabilization of these systems are aided by dust through absorption and scattering of excess energy. As stellar systems evolve and undergo supernova and mass loss events, enriched dust is produced, further enhancing the metallicity of the ISM. However, despite the importance of dust, the processes that produce dust are not well understood. Core-Collapse Supernovae are one source of dust. Dying massive stars explode, sending their constituent material into the Interstellar Medium, which as the ejecta expands and cools, material condenses and nucleates forming dust grains. I investigate the formation, survivability, and properties of dust. In Chapter 2, dust grain nucleation in CCSNe is discussed. A revised formulation of Kinetic Nucleation Theory (KNT) is used to track the nucleation and growth of dust grains in the ejecta. The affects of the progenitor system on the amount and type of dust is explored, showing a strong dependence on explosion energy. I discuss the code and methods used to model dust nucleation and destruction in Chapter 3. The sputtering and erosion of dust grains in CCSNe shocks are explored in Chapter 4. The erosion and survival of this nucleated dust is modeled through thermal and non-thermal sputtering by the surrounding gas and shocks. The optical properties and scattering of light by surviving dust grains is modeled by Mie scattering in Chapter 5. A discussion of observations of dust in variable star systems and supernovae is outlined in Chapter 6.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2025

Polar Bear™ – Innovative Capture of Storage Tank Vapors

Polar Bear™ is a patented technology developed by the Energy & Environmental Research Center (EERC) to capture storage tank vapors and eliminate methane emissions from upstream oil- and gas-producing facilities. Sparked by early commercial investment, the EERC licensed the technology and extended the intellectual property to storage tanks. Polar Bear™ is uniquely engineered and adapted to individual lower-producing facilities where there is otherwise no economic alternative for capturing tank vapors. A high number of small producing oil and gas wells are distributed across the country. The aggregate contributes to a significant volume of emissions. Because of the lack of economy of scale, gas volumes from these facilities are typically not recovered and contribute to methane emissions. Polar Bear™ provides a fit-for-purpose compression solution that addresses cost by reducing complexity with respect to conventional vapor recovery units and eliminating oil changes. Unique to Polar Bear™ is the capability to separate oxygenated gas from storage tank vapors. Storage tanks are designed to “breathe,” allowing gas to enter and escape during internal level and temperature changes. This infiltration of air into the tank headspace imparts undesirable oxygen content with respect to pipeline gathering. Polar Bear™ separates the vapor stream, allowing oxygen-rich gas to be used as fuel on-site while recovering the liquids-rich portion of the gas where oxygen content is minimized. A prototype system was tested to verify process models, evaluate operational performance, and advance the technology readiness level from 5 to 6. Results provide a good match between experimental measurements and process models, indicating the models are useful for future scale-up and field design. Various mixtures of nitrogen and liquefied petroleum gas were tested to understand the mass balance of nitrogen and how it relates to the potential control of oxygen content. Findings indicate that less than 2000 ppm of oxygen is likely to remain in the liquid portion of the gas in field applications. The research and development prepare the technology for field implementation to eliminate routine and fugitive methane emissions from storage tanks.

02 PETROLEUM↗
DOE OSTI2025

Thermal Evaluation of CCS and NACS Reference Devices and Adapters

It is important for manufacturers of electric vehicle charging connectors, inlets, and adapters to understand the thermal performance of their devices. Various standards, such as SAE J1772, SAE J3400, IEC 62196, UL 2251, and UL 2252, list temperature limits that charging hardware needs to meet. However, there are currently very limited standardized reference devices against which to measure connector performance, and those that do currently exist generally serve charging currents less than 500A. This can make determining whether a charging connector meets the appropriate temperature limits difficult. Additionally, as automakers and charging station suppliers transition from the SAE J1772 CCS charging standard to SAE J3400 NACS, a number of CCS-to-NACS and NACS-to-CCS adapters are entering the market. These devices are being produced both by well-known automakers/equipment OEMs and lesser-known third-party suppliers, across a wide range of price points and construction qualities. Though SAE J3400/1 and UL 2252 lay out standards for adapter construction, performance and overtemperature response, there is no guarantee that any particular adapter will follow these standards and react to overtemperature events appropriately. This work addresses these issues by developing and evaluating a set of CCS and NACS reference inlet devices to validate the performance of charging connectors in the 500-800A range. The work also evaluates the performance of multiple NACS-to-CCS and CCS-to-NACS charging adapters with respect to UL 2252 temperature limits and SAE J3400/1 overtemperature signaling criteria.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2026

Data supporting the manuscript "Nanometer Scale Imaging to Develop Quantitative Descriptors of Bipolar Membrane Junction Structure"

This dataset contains atomic force microscopy images associated with the manuscript "Nanometer Scale Imaging to Develop Quantitative Descriptors of Bipolar Membrane Junction Structure" by Maria Kelly, Emily R. Dunn, Ellis A. Spickermann, Josephine N. Gruber, César A. Lasalde-Ramírez, P. N. Romero Zavala, Éowyn Lucas, Ankur Gupta, Harry A. Atwater, and Wilson A. Smith. The dataset contains both raw images as well as segmented images produced by the image processing workflow described in the manuscript. A readme file and meta data file are included to provide additional details regarding the sample identity, image acquisition parameters, and file naming scheme.

36 MATERIALS SCIENCE↗
NASA NTRS1971

Cryogenic glass-filament-wound tank evaluation

High-pressure glass-filament-wound fluid storage vessels with thin aluminum liners were designed, fabricated, and tested at ambient and cryogenic temperatures which demonstrated the feasibility of producing such vessels as well as high performance and light weight. Significant developments and advancements were made in solving problems associated with the thin metal liners in the tanks, including liner bonding to the overwrap and high strain magnification at the vessel polar bosses. The vessels had very high burst strengths, and failed in cyclic fatigue tests by local liner fracture and leakage without structural failure of the composite tank wall. The weight of the tanks was only 40 to 55% of comparable 2219-T87 aluminum and Inconel 718 tanks.

Morris, E. E.↗
NASA NTRS1972

Apollo 15 contamination photography

The problem of optical contamination in the form of particulates in the vicinity of a spacecraft has been a source of concern for any astronomical experiment that must be performed in sunlight. This concern prompted a photographic photometric experiment on Apollo 15 to measure the brightness of the residual contamination cloud as well as the cloud produced by dumping waste water overboard. An upper limit of 10 to the minus 12.3 power B (B designates the brightness of the solar disc) was placed on the residual cloud at a 90 deg sun angle, which is comparable to the zodiacal light. The brightness of the cloud produced by the waste dump was estimated to be 10 to the minus 9.2 power B. It was observed to decrease rapidly to 10 to the -11.6 power B in minutes, then fluctuate in brightness for at least 25 minutes as additional material left the spacecraft. The cloud was observed to consist of individually resolved particle tracks estimated to be particles ranging from millimeters to centimeters in diameter in addition to a background of unresolved particles with an average diameter of 10.5 microns. Most of the tracks proceeded in straight-line paths from the dump nozzle. Several tracks violated this direction, apparently having been scattered by collisions. A few tracks appeared to have definite curvatures, which are believed to be caused by charged particle interactions.

Naumann, R. J.↗
NASA NTRS1973

Parameters controlling nitric oxide emissions from gas turbine combustors

Nitric oxide forms in the primary zone of gas turbine combustors where the burnt gas composition is close to stoichiometric and gas temperatures are highest. It has been found that combustor air inlet conditions, mean primary zone fuel-air ratio, residence time, and the uniformity of the primary zone are the most important variables affecting nitric oxide emissions. Relatively simple model of the flow in a gas turbine combustor, coupled with a rate equation for nitric oxide formation via the Zeldovich mechanism are shown to correlate the variation in measured NOx emissions. Data from a number of different combustor concepts are analyzed and shown to be in reasonable agreement with predictions. The NOx formulation model is used to assess the extent to which an advanced combustor concept, the NASA swirl can, has produced a lean well-mixed primary zone generally believed to be the best low NOx emissions burner type.

Heywood, J. B.↗
NASA NTRS1973

Parameters controlling nitric oxide emissions from gas turbine combustors.

Nitric oxide forms in the primary zone of gas turbine combustors where the burst gas composition is close to stoichiometric and gas temperatures are highest. It has been found that combustor air inlet conditions, mean primary zone fuel-air ratio, residence time, and the uniformity of the primary zone are the most important variables affecting nitric oxide emissions. Relatively simple models of the flow in a gas turbine combustor, coupled with a rate equation for nitric oxide formation via the Zeldovich mechanism are shown to correlate the variation in measured NO sub x emissions. Data from a number of different combustor concepts are analyzed and shown to be in reasonable agreement with predictions. The NO sub x formation model is used to assess the extent to which an advanced combustor concept, the NASA swirl can, has produced a lean well-mixed primary zone generally believed to be the best low NO sub x emissions burner type.

Heywood, J. B.↗
NASA NTRS1973

Mapping of the major structures of the African rift system

The author has identified the following significant results. The new fault map of the main Ethiopian rift, based on aerial photo compilations, generally agrees well with the maps produced from ERTS-1 imagery. Characteristically, the ERTS-1 imagery shows some of the major faults to be more extensive than realized from ground studies, though due to the angle of sun illumination some east-facing fault scarps are not easily discernible on the imagery. The Corbetti caldera, shows up surprisingly poor on the imagery, and is shown to be an adjunct to an older, larger caldera now occupied by Lakes Awassa and Shallo. The lithological boundaries mapped by De Paola in the rift are difficult to discern on the ERTS-1 imagery. On the Somalian plateau, east of the rift, a denuded caldera has been identified as the source of much of the lavas of the Batu Mountains. Further south, ERTS-1 imagery amplifies the structural and lithological mapping of the Precambrian rocks of the Shakisso-Arero area, and of the Kenya-Ethiopia border region. For the first time with some certainty, it is now possible to say that on the evidence of the ERTS-1 imagery, the Western Rift does not continue northeast beyond the Sudan-Uganda border, and is thus not to be sought in western Ethiopia.

Mohr, P. A.↗
NASA NTRS1973

Parameters controlling nitric oxide emissions from gas turbine combustors

Nitric oxide forms in the primary zone of gas turbine combustors where the burnt gas composition is close to stoichiometric and gas temperatures are highest. It was found that combustor air inlet conditions, mean primary zone fuel-air ratio, residence time, and the uniformity of the primary zone are the most important variables affecting nitric oxide emissions. Relatively simple models of the flow in a gas turbine combustor, coupled with a rate equation for nitric oxide formation via the Zeldovich mechanism are shown to correlate the variation in measured NOx emissions. Data from a number of different combustor concepts are analyzed and shown to be in reasonable agreement with predictions. The NOx formation model is used to assess the extent to which an advanced combustor concept, the NASA swirl can, has produced a lean well-mixed primary zone generally believed to be the best low NOx emissions burner type.

Heywood, J. B.↗
NASA NTRS1974

Vortex-induced heating to a cone-cylinder body at Mach 6

Presented data on vortex-induced heating in a cone-cylinder body at Mach 6 show that the most severe heating need not occur as a result of the interaction of the primary vortices with the lee surface, even though this interaction produces a large, well-defined featherline oil smear. It is pointed out that the severity of vortex-induced heating is extremely sensitive to Reynolds number and geometry and that there exists a 'threshold Reynolds number' below which vortex-induced heating decreases abruptly.

Hefner, J. N.↗
NASA NTRS1979

Chemical kinetic modeling of benzene and toluene oxidation behind shock waves

The oxidation of stoichiometric mixtures of benzene and toluene behind incident shock waves was studied for a temperature range from 1700 to 2800 K and a pressure range from 1.1 to 1.7 atm. The concentration of CO and CO2 produced were measured as well as the product of the oxygen atom and carbon monoxide concentrations. Comparisons between the benzene experimental data and results calculated by use of a reaction mechanism published in the open literature were carried out. With some additional reactions and changes in rate constants to reflect the pressure-temperature range of the experimental data, a good agreement was achieved between computed and experimental results. A reaction mechanism was developed for toluene oxidation based on analogous rate steps from the benzene mechanism. Measurements of NOx levels in an actual flame device, a jet-stirred combustor, were reproduced successfully by use of the reaction mechanism developed from the shock-tube experiments on toluene. These experimental measurements of NOx levels were reproduced from a computer simulation of a jet-stirred combustor.

Mclain, A. G.↗
NASA NTRS1979

I-Xe dating of silicate and troilite from IAB iron meteorites

Silicate and troilite inclusions from IAB iron meteorites were dated by the I-Xe technique. Silicate samples from inclusions in the Copiapo, Landes, Woodbine, Pitts and Mundrabilla meteorites and troilite samples from Pitts and Mundrabilla were subjected to neutron irradiation and the xenon isotope ratios produced were determined. Well-defined I-Xe ages were obtained for Woodbine, Copiapo, Landes and Mundrabilla and are found to be within 3.7 million years of the Bjurbole meteorite, suggesting a close relationship to the stone chondrites. The analysis of troilite from Pitts suggests an age of 17 million years older than Bjurbole, while Mundrabilla troilite is observed to predate Mundrabilla silicate. The abundances of Ga, Ge and Ni are found to be correlated with I-Xe ages, supporting the validity of the I-Xe dating method. The results are considered to favor a nebular model of meteorite formation.

Niemeyer, S.↗
NASA NTRS1979

Development of ultraviolet rigidizable materials

A series of tests was performed to determine an optimum resin to be used as a UV rigidizable matrix in expandable rigidizable space structures. Commercially available resins including several types of polyesters, epoxies, epoxy-acrylics, an acrylic and a urethane were used as well as a polyester, produced by 3M Company's Solar Laboratory facility, which was found the best from the standpoint of physical properties and ability to be 'B' staged. Two other synthesized materials were also tested, but were not found to be superior to the Solar resin. An optimum fabric for use with the preferred resin was not found; however, the 15 ounce fabric from Solar Laboratories has the best combination of physical properties with respect to handling and processing characteristics. Expansion techniques for tubular structures, 'B' staging of the solar resin, and stowage techniques for up to 5 months were developed. A one meter high tetrahedron preprototype structure was prepared to evaluate and demonstrate stowage, deployment, and rigidization techniques.

Salisbury, D. P.↗
NASA NTRS1981

Low-visibility visual simulation with real fog

An environmental fog simulation (EFS) attachment was developed to aid in the study of natural low-visibility visual cues and subsequently used to examine the realism effect upon the aircraft simulator visual scene. A review of the basic fog equations indicated that two major factors must be accounted for in the simulation of low visibility - one due to atmospheric attenuation and one due to veiling luminance. These factors are compared systematically by (1) comparing actual measurements to those computed from the fog equations, and (2) comparing runway-visual-range-related visual-scene contrast values with the calculated values. These values are also compared with the simulated equivalent equations and with contrast measurements obtained from a current electronic fog synthesizer to help identify areas in which improvements are needed. These differences in technique, the measured values, the features of both systems, a pilot opinion survey of the EFS fog, and improvements (by combining features of both systems) that are expected to significantly increase the potential as well as flexibility for producing a very high-fidelity low-visibility visual simulation are discussed.

Chase, W. D.↗
NASA NTRS1981

An implicit marching procedure for the treatment of supersonic flow fields using the conservative full potential equation

A new aerodynamic prediction technique based on the conservative full potential equation is developed for the treatment of supersonic flow fields. This new technique bridges the gap between simplistic linear theory methods and complex Euler solvers. A novel local density linearization concept and a second order accurate retarded density scheme, both producing the correct artificial viscosity, are introduced in developing an implicit marching scheme for solving the scalar phi. The method produces results that compare well with Euler solvers and requires an order of magnitude less computer time and significantly less computer memory over existing nonlinear codes. The scalar phi formulation can be extended to handle subsonic pockets in the marching direction and also is suitable for developing inverse procedures where the shape corresponding to a prescribed loading is sought.

Shankar, V.↗