Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “plastic strains”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Cryogenic mechanical behaviors of CrMnFeCoNi high-entropy alloy

The CrMnFeCoNi high-entropy alloy (HEA) exhibits higher yield strength, ultimate strength and ductility at lower temperature. To further clarify the effect of the testing temperature on microstructure evolution, in this study in-situ synchrotron-based high-energy X-ray diffraction tensile tests were carried out from 298 K down to 123 K. The enhanced yield strength of the alloy at cryogenic temperatures can be attributed to the greater lattice distortion prior to plastic deformation. Higher strain hardening rate leads to the simultaneously enhanced strength and ductility of the studied HEA below room temperature. Both dynamic Hall-Petch hardening (twinning) and dislocation hardening provide high work hardening capacity for this alloy during the plastic deformation at cryogenic temperatures. The increased dislocation density and nano-twins at cryogenic temperatures can be attributed to the decrease in the stacking fault energy as the deformation temperature decreases. These studies could provide an in-depth understanding for the strengthening mechanisms of the HEA in different temperature conditions and guide the exploration of HEAs with superb mechanical properties at cryogenic environments.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Real-Time Observation of Nanoscale Kink Band Mediated Plasticity in Ion-Irradiated Graphite: An In Situ TEM Study

Graphite IG-110 is a synthetic polycrystalline material used as a neutron moderator in reactors. Graphite is inherently brittle and is known to exhibit a further increase in brittleness due to radiation damage at room temperature. To understand the irradiation effects on pre-existing defects and their overall influence on external load, micropillar compression tests were performed using in situ nanoindentation in the Transmission Electron Microscopy (TEM) for both pristine and ion-irradiated samples. While pristine specimens showed brittle and subsequent catastrophic failure, the 2.8 MeV Au2+ ion (fluence of 4.378 × 1014 cm−2) irradiated specimens sustained extensive plasticity at room temperature without failure. In situ TEM characterization showed nucleation of nanoscale kink band structures at numerous sites, where the localized plasticity appeared to close the defects and cracks while allowing large average strain. We propose that compressive mechanical stress due to dimensional change during ion irradiation transforms buckled basal layers in graphite into kink bands. The externally applied load during the micropillar tests proliferates the nucleation and motion of kink bands to accommodate the large plastic strain. The inherent non-uniformity of graphite microstructure promotes such strain localization, making kink bands the predominant mechanism behind unprecedented toughness in an otherwise brittle material.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Anisotropic elastoplastic response of double-porosity media

Here we present a continuum framework to simulate fluid flow through anisotropic elastoplastic media with double porosity. Two effective stress measures σ' and δ" emerge from the thermodynamic formulation, which are energy-conjugate to the elastic and plastic components of strain, respectively. Both effective stress measures can be expressed as a combination of the total Cauchy stress σ and the average pore pressure $\bar{p}$ in the two pore scales. In the effective stress for elasticity, $\bar{p}$ is scaled with a rank-2 Biot tensor, whereas the effective stress for plasticity follows the Terzaghi form in which $\bar{p}$ is scaled by the Kronecker delta. The Biot tensor and storage coefficients are derived as functions of elasticity parameters and porosities. A mixed finite element formulation is introduced to discretize the domain and solve initial boundary-value problems. A stabilization scheme is employed on equal-order interpolation for both displacement and pressure fields throughout the entire range of drainage responses. Numerical simulations reproduce the hydromechanical response of Opalinus shale in one-dimensional consolidation tests throughout the range of primary and secondary consolidation under different external loads. Numerical simulations of the consolidation of a rectangular domain subjected to a strip load demonstrate the efficacy of the proposed stabilization scheme, as well as illustrate the impacts of stress history, mass transfer, and different pore systems on the hydromechanical response.

42 ENGINEERING↗
DOE OSTI2023

Exploring pressure-dependent inelastic deformation and failure in bonded granular composites: An energetic materials perspective

In polymer-filled granular composites, damage may develop in mechanical loading prior to material failure. Damage mechanisms such as microcracking or plastic deformation in the binder phase can substantially alter the material’s mesostructure. For energetic materials, such as solid propellants and plastic bonded explosives, these mesostructural changes can have far reaching effects including degraded mechanical properties, potentially increased sensitivity to further insults, and changes in expected performance. Unfortunately, predicting damage is nontrivial due to the complex nature of these composites and the entangled interactions between inelastic mechanisms. In this work, we assess the current literature of experimental knowledge, focusing on the pressure-dependent shear response, and propose a simple simulation framework of bonded particles to study four limiting-case material formulations at both meso- and macro-scales. Further, to construct the four cases, we systematically vary the relative interfacial strength between the polymer binder and granular filler phase and also vary the polymer’s glass transition temperature relative to operating temperature which determines how much the binder can plastically deform. These simulations identify key trends in global mechanical response, such as the emergence of strain hardening or softening regimes with increasing pressure which qualitatively resemble experimental results. By quantifying the activation of different inelastic mechanisms, such as bonds breaking and plastically straining, we identify when each mechanism becomes relevant and provide insight into potential origins for changes in mechanical responses. The locations of broken bonds are also used to define larger, mesoscopic cracks to test various metrics of damage. We primarily focus on triaxial compression, but also test the opposite case of triaxial extension to highlight the impact of Lode angle on mechanical behavior.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Kink band and shear band localization in anisotropic perfectly plastic solids

Shear-driven strain localization has been observed in a wide variety of materials and may take the form of shear bands or kink bands. Based on observations of kink bands in plastically anisotropic metallic nanolaminates and single crystal metals, here we posit that, for the specific case of isochoric deformation, the kinematics of kink band formation are indistinguishable from those of plane strain shear band formation. The only distinction between shear bands and kink bands in these systems would then be that kink bands ‘lock up’ at a particular value of material rotation while shear bands may progress to arbitrarily high strains. In order to investigate whether strong material anisotropy is sufficient to arrest shear localization at a geometry that matches the classic kink band geometry, we model the development of a band of simple shear within an anisotropic perfectly plastic material. The resulting analytical model provides the stress state needed to maintain the kinematics of simple shear as a function of material anisotropy, deformation band orientation, and shear strain (or equivalently, material rotation). It is found that plastic anisotropy can promote either kink band or shear band formation depending on the loading orientation. When the deviatoric stress is positive parallel to the plane of anisotropy, shear localization may progress without bound and a shear band is produced. When the deviatoric stress is negative parallel to the plane of anisotropy, shear localization is arrested after a certain material rotation, resulting in a kink band. Examination of the requisite applied stress state during kink band formation provides an explanation for the experimentally-observed ‘lock up’ geometry. Solutions for the band boundary inclination angle are obtained and used to provide bounds on permissible band angles for both shear bands and kink bands.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Thermal-Mechanical Elastic-Plastic and Ductile Failure Model Calibrations for 304L Stainless Steel Alloy

Numerical simulations of metallic structures undergoing rapid loading into the plastic range require material models that accurately represent the response. In general, the material response can be seen as having four interrelated parts: the baseline response under slow loading, the effect of strain rate, the conversion of plastic work into heat and the effect of temperature. In essence, the material behaves in a thermal-mechanical manner if the loading is fast enough so when heat is generated by plastic deformation it raises the temperature and therefore influences the mechanical response. In these cases, appropriate models that can capture the aspects listed above are necessary. The material of interest here is 304L stainless steel, and the objective of this work is to calibrate thermal-mechanical models: one for the constitutive behavior and another for failure. The work was accomplished by first designing and conducting a material test program to provide data for the calibration of the models. The test program included uniaxial tension tests conducted at room temperature, 150 and 300 C and at strain rates between 10 –4 and 10 3 1/s. It also included notched tension and shear-dominated compression hat tests specifically designed to calibrate the failure model. All test specimens were extracted from a single piece of plate to maintain consistency. The constitutive model adopted was a modular $J_2$ plasticity model with isotropic hardening that included rate and temperature dependence. A criterion for failure initiation based on a critical value of equivalent plastic strain fitted the failure data appropriately and was adopted. Possible ranges of the values of the parameters of the models were determined partially on historical data from calibrations of the same alloy from other lots and are given here. The calibration of the parameters of the models were based on finite element simulations of the various material tests using relatively ne meshes and hexahedral elements. When using the model in structural finite element calculations, however, element formulations and sizes different from those in the calibration are likely to be used. A brief investigation demonstrated that the failure initiation predictions can be particularly sensitive to the element selection and provided an initial guide to compensate for the effect of element size in a specific example.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Effects of Strain and Strain Rate on Dynamic Grain Growth and Subgrain Evolution During Plastic Deformation of an Interstitial-Free Steel at 850 ° C

Here, the effects of strain and strain rate on dynamic grain growth (DGG) and subgrain evolution are reported for an interstitial-free steel deformed at 850 ° C. Microstructures produced during tension tests at true-strain rates of 10 -4 and to 10 -3 s -1 true strains ranging from 0.02 to 0.2 were preserved following deformation. These were characterized using electron backscatter diffraction (EBSD), including the application of spherical harmonic transform indexing to produce high-angular-resolution EBSD (HR-EBSD) data. HR-EBSD data resolved the small misorientation angles of subgrain boundaries while imaging much larger data fields than possible with previously available techniques. The resulting data confirmed that steady-state flow stress is inversely proportional to the average subgrain size and that subgrain boundary misorientation angle increases with strain. The following new observations are reported. The rate of DGG increased with respect to time but decreased with respect to strain as strain rate increased. This behavior is rationalized through a simple model using separate rate parameters for the effects of time and strain. Subgrain size was not constant during steady-state deformation, but decreased slowly with increasing strain. Subgrain size distributions and subgrain boundary misorientation angle distributions were measured, and both remained approximately log-normal during steady-state deformation. Subgrain evolution demonstrated no dependence on parent grain size, crystallographic orientation, or Taylor factor. These new data suggest that steady-state flow stress is more likely controlled by the dislocation density internal to subgrains than by the spacing between subgrain boundaries.

dynamic grain growth↗
DOE OSTI2022

Effect of microstructure on fatigue crack propagation in additive manufactured nickel-based superalloy Haynes 282: an experiment and crystal plasticity study

Haynes 282 is a γ' precipitation-strengthened nickel-based superalloy known for its exceptional high-temperature creep resistance and excellent fabricability. Recent advancements in powder-bed fusion-based additive manufacturing (PBF-AM) have enabled the fabrication of Haynes 282 with accurate, site-specific control of the grain orientation and morphology at the microscale. This ability opens up new avenues for microstructure design, to improve the material’s fatigue crack resistance and service life. This paper investigates the fatigue crack growth behavior of hybrid microstructure Haynes 282 fabricated via PBF-AM. Previous experiments revealed a higher crack propagation rate in the coarse columnar-grained microstructural regions when compared against fine-grained areas. Here, a strain gradient crystal plasticity model was adapted to study the fracture-related mechanical fields at the crack tip in the two microstructures. The simulation results showed a consistent influence of grain structure and texture on crack propagation, as was seen in the experiment. The model analysis revealed higher crack propagation driving force along crack direction in the coarse-grained sharply textured microstructure and higher driving force for crack kinking in fine-grained more diffusely textured microstructure, which is ascribed to the combined effect of yield stress, hardening rate, texture and grain morphology. The presented modeling approach will facilitate the development of the AM-based accurate microstructure design by deepening the fundamental study in AM-specific microstructure-properties relations.

36 MATERIALS SCIENCE↗
NASA NTRS1973

Nonlinear crack analysis with finite elements

The application of finite element techniques to the analytic representation of the nonlinear behavior of arbitrary two-dimensional bodies containing cracks is discussed. Specific methods are proposed using which it should be possible to obtain information concerning: the description of the maximum, minimum, and residual near-tip stress and strain fields; the effects of crack closure on the near-tip behavior of stress and strain fields during cyclic loading into the plastic range; the stress-strain and displacement field behavior associated with a nonstationary crack; and the effects of large rotation near the crack tip.

Armen, H., Jr.↗
NASA NTRS2017

An Overview of Materials Structures for Extreme Environments Efforts for 2015 SBIR Phases I and II

Technological innovation is the overall focus of NASA's Small Business Innovation Research (SBIR) program. The program invests in the development of innovative concepts and technologies to help NASA's mission directorates address critical research and development needs for Agency projects. This report highlights innovative SBIR 2015 Phase I and II projects that specifically address areas in Materials and Structures for Extreme Environments, one of six core competencies at NASA Glenn Research Center. Each article describes an innovation, defines its technical objective, and highlights NASA applications as well as commercial and industrial applications. Ten technologies are featured: metamaterials-inspired aerospace structures, metallic joining to advanced ceramic composites, multifunctional polyolefin matrix composite structures, integrated reacting fluid dynamics and predictive materials degradation models for propulsion system conditions, lightweight inflatable structural airlock (LISA), copolymer materials for fused deposition modeling 3-D printing of nonstandard plastics, Type II strained layer superlattice materials development for space-based focal plane array applications, hydrogenous polymer-regolith composites for radiation-shielding materials, a ceramic matrix composite environmental barrier coating durability model, and advanced composite truss printing for large solar array structures. This report serves as an opportunity for NASA engineers, researchers, program managers, and other personnel to learn about innovations in this technology area as well as possibilities for collaboration with innovative small businesses that could benefit NASA programs and projects.

integrated reacting fluid dynamics and predictive ↗
DOE OSTI2022

Strain-rate dependent deformation mechanisms in single-layered Cu, Mo, and multilayer Cu/Mo thin films

Here, strain-rate sensitivity and rate-dependent hardness, over a range of 10 -2 to 10 2 s -1 , of sputter-deposited single-layered Cu, Mo, and 5 nm Cu/ 5 nm Mo, and 100 nm Cu/ 100 nm Mo multilayer films with a total film thickness of 5 μm were measured using nanoindentation. The plastic zone underneath the nanoindents was characterized via cross-sectional transmission electron microscopy (XTEM). The multilayer films exhibited enhanced hardness but slightly reduced strain-rate sensitivity with decreasing layer thickness from 100 nm to 5 nm. Only the 5 nm Cu/ 5 nm Mo multilayer film exhibited shear bands underneath the nanoindents, and the size of the shear bands increased with increasing strain rate. In contrast, the 100 nm Cu/ 100 nm Mo multilayer film exhibited material pile-up around the indents and significant nanotwinning within Cu grains. The effect of strain rate and layer thickness on the hardness and strain rate sensitivity of the multilayer thin films is interpreted using a modified confined layer slip (CLS) model. The reduced rate sensitivity at 5 nm as compared to 100 nm correlates with abundant growth nanotwins in the Cu grains in 100 nm and formation of shear bands in 5 nm multilayers. In single layer films, a substructure with a high density of dislocations was observed consistent with the plastic strain gradient in the indent plastic zone. No evidence of deformation twins was noted in any of the samples.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Chemical complexity suppresses interstitial solute segregation to screw dislocation cores in the bcc NbTaTiHfZr high-entropy alloy

Recent reports suggest that interstitial solute additions to body-centered cubic (bcc) high-entropy alloys (HEAs) may enhance their mechanical properties. However, details of interactions between interstitial atoms and dislocations in these HEAs remain incompletely understood. Using first-principles calculations, we examine the energetics of C, N, and O interstitial solutes in elemental bcc metals and NbTaTiHfZr, focusing on their segregation in screw dislocation cores. We examine two types of core sites and show that the low-energy configuration and associated segregation energy depend on the transition metal group. In NbTaTiHfZr, we find that chemical complexity substantially suppresses interstitial segregation in dislocation cores, as fluctuations in bulk solute energies induce energetically favorable sites that disfavor segregation to core sites. Local chemical order further enhances this effect by promoting solute clustering away from dislocation cores. These findings reveal fundamental differences between the behavior of interstitial atoms in elemental metals and HEAs, with implications for high-temperature plasticity and dynamic strain aging.

Body-centered cubic transition metals↗
DOE OSTI2022

Atomistic simulations of nanoindentation on nanoglasses: Effects of grain size and gradient microstructure on the mechanical properties

The use of nanoglass (NG) microstructures has been shown as an effective strategy to improve the ductility of rather brittle metallic glass alloys. To evaluate the effects of grain size and gradient design on the mechanical properties of NGs, we perform molecular dynamics simulations of nanoindentation on Cu 64 Zr 36 NGs. We consider samples with uniform 3 and 7 nm grain sizes as well as gradient microstructures with gradient grain sizes varying from 3 to 7 nm. Here, the results show that the deformation mechanism in NGs with small grain sizes is dominated by the activation and evolution of multiple shear transformation zones. Increasing grain sizes enhances the elastic modulus and hardness at the cost of reduced abrasion resistance. Though the average grain size at the indentation surface plays a crucial role in the deformation behavior of gradient NG models, their strain localization and plastic deformation states are affected by the grain sizes far from the indenter. Desired combinations of mechanical properties can be realized by different NG microstructure designs.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Ductile Glassy Polymer Networks Capable of Large Plastic Deformation and Heat-Induced Elastic Recovery

Many thermoplastic polymers are ductile by combining strength and large deformations. These deformations are irreversible - known as plastic deformation. Elastomers can deform reversibly but have low strength. To this end, we developed glassy and ductile polyamide networks capable of large plastic deformation (>200% strain) and high strength (~50 MPa tensile strength and ~1500 MPa Young’s modulus), similar to those of polyolefins and Nylon-66. We discovered that hydrogen bonding between meta-phthalamide groups was essential to the ductility. Since these polyamide networks are covalently bonded, we demonstrated their unique durability by repeatable elastic recovery at elevated temperatures, exhibiting indifferent tensile properties in each cycle. Furthermore, when we fixed the strain during the elastic recovery, these polyamide networks actuated stresses of 9–18 MPa, among the highest reported in shape-memory polymer actuators. Here, we envision these ductile, glassy polymer networks as promising alternatives to ductile thermoplastics, given the combined benefit of ductility and durability.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A compact x-ray diffraction system for dynamic compression experiments on pulsed-power generators

Pulsed-power generators can produce well-controlled continuous ramp compression of condensed matter for high-pressure equation-of-state studies using the magnetic loading technique. X-ray diffraction (XRD) data from dynamically compressed samples provide direct measurements of the elastic compression of the crystal lattice, onset of plastic flow, strength–strain rate dependence, structural phase transitions, and density of crystal defects, such as dislocations. Here, we present a cost-effective, compact, pulsed x-ray source for XRD measurements on pulsed-power-driven ramp-loaded samples. This combination of magnetically driven ramp compression of materials with a single, short-pulse XRD diagnostic will be a powerful capability for the dynamic materials’ community to investigate in situ dynamic phase transitions critical to equation of states. Finally, we present results using this new diagnostic to evaluate lattice compression in Zr and Al and to capture signatures of phase transitions in CdS.

47 OTHER INSTRUMENTATION↗