SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Computer program PACER-65, is used for flowsheet calculations and easily adapted to process data reduction. Each unit, vessel, meter, and processing operation in the overall flowsheet is represented by a separate subroutine, which the program calls in the order required to complete an overall flowsheet calculation.
Measurement of abundances of Na, Al, Sc, Cr, Mn, Fe, Co, and Cu by instrumental neutron activation analyses of 103 chondrites and 17 achondrites. Various sources of error in the method, including sampling errors, are discussed in detail. Examination of the patterns of coherence of the elements determined suggests the presence of effects of fractionation during condensation from the solar nebula of matter parental to chondrites. Such effects seem to be exhibited both in the abundances of lithophilic elements, perhaps being related to varied temperatures of accretion and in the abundances of those elements which would be affected by metal-silicate fractionation in the solar nebula. Atomic abundances relative to Si vary little in carbonaceous chondrites, suggesting that efficient mixing processes operated on these meteorites prior to or during their formation. It is suggested that, at present, no single class of carbonaceous chondrites is clearly more primitive than another. Carbonaceous and unequilibrated ordinary chondrites may represent aggregates of material accreted from the solar nebula at relatively low temperatures. The present data support a model of equilibration and minor mobilization of nonvolatile elements within small domains of chondrites after accretion. Such a model would be consistent with the petrologic types of Van Schmus and Wood (1967).
A feasibility study was made of the application of silicon-controlled, rectifier series, resonant inverter, power conditioning technology to electric propulsion power processing operating from a 200 to 400 Vdc solar array bus. A power system block diagram was generated to meet the electrical requirements of a 20 CM hollow cathode, mercury bombardment, ion engine. The SCR series resonant inverter was developed as a primary means of power switching and conversion, and the analog signal-to-discrete-time-interval converter control system was applied to achieve good regulation. A complete breadboard was designed, fabricated, and tested with a resistive load bank, and critical power processor areas relating to efficiency, weight, and part count were identified.
An investigation was conducted to evaluate the stability of a specific low expansion glass-ceramic material relative to its use as a large, lightweight mirror substrate for diffraction-limited spaceborne optical applications. These evaluations were made on a segment (0.44 meter diameter by 0.31 meter thick) of a 2 to 3 meter diameter mirror blank. The dimensional stability of this mirror was measured interferometrically before and after lightweighting, as a function of rough machining, etching, thermal environment, and support configuration. A special computer analysis program was used to plot the coefficients corresponding to aberrations with sixfold symmetry (caused by the mirror's self-weight deflection on a three point support). The objective was to enhance the test sensitivity. Results indicate that any such effects due to self-weight deflection are of the order of 0.015 lambda rms. The rms and peak-to-peak figure changes associated with each processing operation are summarized.
By readily levitating, positioning, and manipulating materials placed in it, the acoustical resonator can serve a variety of space processing operations, such as drawing crystals, degassing, and stirring of melts, and casting.
The water vapor electrolysis (WVE) reactor is a spacecraft waste reclamation system for extended-mission manned spacecraft. The WVE reactor's raw material is water, its product oxygen. A computer simulation of the WVE operational processes provided the data required for an optimal design of the WVE unit. The simulation process was implemented with the aid of a FORTRAN IV routine.
The magnetic properties of lunar samples are almost exclusively due to rather pure metallic iron. The mare basalt contains about 0.06 wt.% Fe, the soils 0.5-0.6 wt.%, and the breccias 0.3-1.0 wt.%. Most of the additional iron in the soils and breccias is believed to be the result of reduction processes operating on the lunar surface. Whereas the total metallic iron content of the soils from all landing sites is rather constant, the Fe(0)/Fe(++) ratio and the average iron grain size increase with the age of the landing site, reflecting increasing maturity. The crystalline rocks studied from Apollo 16 have highly variable, but generally, very high metallic Fe content (up to 1.7 wt.% Fe). It is suggested that these rocks are either breccias or igneous samples which have been severely thermally metamorphosed in a highly reducing environment.
The characteristics of the electron acceleration process operating during the flash phase of solar flares are deduced from the high time resolution observations of impulsive solar X rays greater than or equal to 10 keV and other flash phase emissions from small solar flares, and the implications of these findings are discussed.
Differential thermal expansion was shown to be responsible for many observed failures in ceramic chip capacitors mounted on alumina substrates. It is shown that the mounting techniques used in bonding the capacitors have a marked effect upon the thermally induced mechanical stress and thus the failure rate. A mathematical analysis was conducted of a composite model of the capacitor-substrate system to predict the magnitude of thermally induced stresses. It was experimentally observed that the stresses in more compliant bonding systems such as soft lead tin and indium solders are significantly lower than those in hard solder and epoxy systems. The marked dependence upon heating and cooling rate was proven to be a determining factor in the prediction of failure solder systems. It was found that the harder or higher melting solders are less susceptible to thermal cycling effects but that they are more likely to fail during initial processing operations. Strain gage techniques were used to determine thermally induced expansion stresses of the capacitors and the alumina substrates. The compliance of the different bonding mediums was determined. From the data obtained, several recommendations are made concerning the optimum bonding system for the achievement of maximum reliability.
Preliminary processing operations required before computer compatible tapes (CCT) can be utilized routinely to realize the full potential of ERTS imagery for rapid mensuration, quantitative estimation and for detecting and monitoring changes over time are described. Geographic referencing, geometric manipulations, classification, and association overlays (as of political boundaries) are discussed.
The effect of thermal cycling on the mechanical failure of bonded ceramic chip capacitors mounted on alumina substrates is studied. It is shown that differential thermal expansion is responsible for the cumulative effects which lead to delayed failure of the capacitors. Harder or higher melting solders are found to be less susceptible to thermal cycling effects, although they are more likely to fail during initial processing operations.
Program uses minimal core and time resources and performs following analysis functions: artwork verification, device identification, nodal analysis, capacitance calculation, and logic equation generation. For data base simplicity, program processing operates on mask data which has been coverted from its original form to orthogonal rectangles.
Topics related to architectural and institutional considerations are discussed along with studies of components and subsystems. Subjects in the area of system design and analysis are also explored. Residential and commercial applications are considered, taking into account hot-water usage in a typical single-family residence, solar heating and cooling of mobile homes, aspects of design and performance in the case of a solar heating system using a reflective pyramid optical condenser, solar heating in a Boston school, a performance analysis of solar service hot water systems, comparative performance analyses of three solar heated and cooled buildings, and the use of solar energy in a soybeam processing operation. Applications related to power generation are also examined, giving attention to solar thermal electric power systems and photovoltaic research. Individual items are announced in this issue.
Differential thermal expansion has been shown to be responsible for many observed failures in ceramic chip capacitors mounted on alumina substrates. The present work has shown that the mounting techniques used in bonding the capacitors have a marked effect upon the thermally induced mechanical stress and thus the failure rate. A mathematical analysis of a composite model of the capacitor-substrate system to predict the magnitude of thermally induced stresses has been conducted. It has been observed that the stresses in more compliant bonding systems such as soft lead/tin and indium solders are significantly lower than those in hard solder and epoxy systems. The marked dependence upon heating and cooling rate has proven to be a determining factor in the prediction of failure in both the indium and tin/lead solder systems. This study has shown that the harder or higher melting solders are less susceptible to thermal cycling effects but that they are more likely to fail during initial processing operations. Recommendations are made concerning the optimum bonding system for the achievement of maximum reliability.
The data multiplexing unit described is a low-power small-size building-block-type central data system designed for use on such spacecraft as the International Ultraviolet Explorer or the International Sun-Earth Explorer. Preprogrammed read-only memories are used to generate the telemetry format tailored to particular mission requirements. Low weight and low power dissipation are achieved with the aid of PMOS technology. The use of subcommutators in groups to meet particular spacecraft requirements allows low data rate experiments to be time-multiplexed into a single main input channel, to improve data collection and processing operations. The block diagram of the Dataplexer is discussed.
A statistical investigation is conducted concerning the plasmapause behavior observed from Explorer 45 during various levels of magnetic activity. Aspects of data handling are reported and the implications of a constant density level for a plasmapause definition are discussed. The average local time dependence of the gradient saturation events and the sharp saturation events detected on Explorer 45 is shown with the aid of graphs. Other graphs show the results of the statistical processing operations. The significance of the obtained data is discussed.
The paper describes an LST ground system which is compatible with the operational requirements of the LST. The goal of the approach is to minimize the cost of post launch operations without seriously compromising the quality and total throughput of LST science. Attention is given to cost constraints and guidelines, the telemetry operations processing systems (TELOPS), the image processing facility, ground system planning and data flow, and scientific interfaces.
Development of coal feed systems for coal gasification, fluidized bed combustion, and magnetohydrodynamic applications is discussed. Process operations experience, energy conversion efficiency, and environment effects are among the factors considered.