Mesoscale Modeling of Shock Induced Reactions in Nickel + Aluminum Multilayer Thin Films
Short paper for an international conference with archival proceedings that are due prior to the talk.
Kittell, David E. [Sandia National Laboratories (S↗
SEARCH · Engineering Papers
Results for “multilayers.”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
In situ indentation and high cycle tapping deformation responses in a nanolaminate crystalline/amorphous metal composite
The incorporation of nanostructured and amorphous metals into modern applications is reliant on the understanding of deformation and failure modes in constrained conditions. To study this, a 105 nm crystalline Cu/160 nm amorphous Cu 45 Zr 55 (at.%) multilayer structure was fabricated with the two crystalline layers sputter deposited between the top-middle-bottom amorphous layers and prepared to electron transparency. The multilayer was then in situ indented either under a single load to a depth of ~ 100 nm (max load of ~ 100 μN) or held at 20 μN and then repeatedly indented with an additional 5 μN up to 20,000 cycles in a transmission electron microscope to compare the deformation responses in the nanolaminate. For the single indentation test, the multilayer showed serrated load-displacement behavior upon initial indentation inductive of shear banding. Additionally, at an indentation depth of ~ 32 nm, the multilayer exhibited perfect plastic behavior and no strain hardening. Both indented and fatigue-indented films revealed diffraction contrast changes with deformation. Subsequent Automated Crystal Orientation Mapping (ACOM) measurements confirmed and quantified global texture changes in the crystalline layers with specifically identified grains revealing rotation. Using a finite element model, the in-plane displacement vectors under the indent mapped conditions where ACOM determined grain rotation was observed, indicating the stress flow induced grain rotation. Furthermore, the single indented Cu layers also exhibited evidence of deformation induced grain growth, which was not evident in the fatigue-indented Cu based multilayer. Finally, the single indented multilayer retained a significant plastic crater in the upper most amorphous layer that directly contacted the indenter; a negligible crater impression in the same region was observed in the fatigued tested multilayer. These differences are explained by the different loading methods, applied load, and deformation mechanisms experienced in the multilayers.
36 MATERIALS SCIENCE↗
Crystalline 1D Coordination Polymer Inhibitor Layer Leads to Vertical Sidewalls in Selectively Deposited ZnO on Nanoscale Patterns
Area-selective atomic layer deposition (AS-ALD) is a promising technique for the fabrication of next-generation nanoelectronics. There are two main challenges in AS-ALD: (1) achieving high selectivity of deposition on the growth regions, and (2) preventing mushrooming of the growth material onto the nongrowth regions and achieving well-defined interfaces. In this work, we use benzenethiol (BT) as an inhibitor in the selective deposition of ZnO on SiO 2 in the presence of copper with and without a native oxide (Cu/CuO x ). We observe that BT forms a monolayer on the Cu surface and a Cu-thiolate multilayer structure on CuO x . Using grazing incidence X-ray diffraction combined with simulations, we find that the multilayer structure is crystalline and composed of 1D coordination polymers of Cu-thiolate. Here, using ellipsometry and X-ray photoelectron spectroscopy, we show that the BT consumes the entirety of the CuO x during multilayer formation, allowing the multilayer thickness to be tuned by the thickness of the original oxide. Both the monolayer BT and the multilayer BT prove to be effective inhibitors of ZnO ALD, blocking nearly 500 ALD cycles, which is more than twice that achieved with other thiol inhibitors. Finally, we demonstrate that the multilayer structure can prevent mushrooming of the ALD material onto the nongrowth surface of nanoscale patterns, creating vertical sidewalls with well-defined material interfaces and providing excellent pattern transfer, even for a relatively thick deposited film. As such, these results demonstrate that BT is not only an effective inhibitor but also that its ability to form tunable multilayers makes it well-suited for highly precise nanopatterning applications.
Layers↗
Picometer sensitivity metrology for EUV absorber phase
With growing interest in EUV attenuated phase-shift masks due to their superior image quality for applications such as dense contact and pillar arrays, it is becoming critical to model, measure, and monitor the intensity and relative phase of multilayer and absorber reflections. We present a solution based on physical modeling of reflectometry data, which can achieve single picometer phase precision and sensitivity to changes in average film thickness below one atomic monolayer. We measure absorber and multilayer reflectivity to determine thin-film parameters with a multidimensional optimization and then acquire a new measurement of either multilayer or absorber to determine perturbations in surface contamination thickness. While it is difficult to assess the accuracy of the first step, the simplicity of the second step allows us to characterize our sensitivity to changes in contamination thickness. Thus, we apply this analysis using an initial set of measurements and repeated measurements after a period of storage. For the multilayer, the total contamination growth was 1068 pm, which occurred almost exclusively during storage (1085 pm) and decreased very slightly during repeated measurements (-17 pm). For the absorber, the behavior was quite different, with a total growth of 126 pm, which occurred much less during storage (28 pm) and primarily during repeated measurements (98 pm). Ultimately, the change in relative phase (absorber minus multilayer) was -0.86 deg for the multilayer and -1.12 deg for the absorber. We estimate the precision of the surface contamination measurement to be 3σ < 6 pm for measuring thickness and 3σ < 0.2 deg for measuring phase.
36 MATERIALS SCIENCE↗
Commissioning of a two-target DC cylindrical magnetron sputter coater for depositing Nb 3 Sn film on Nb superconducting radiofrequency cavities
A DC cylindrical magnetron sputter coater was commissioned and used to coat Nb 2.6 GHz superconducting radiofrequency (SRF) cavity with Nb 3 Sn. The sputter coater has two identical cylindrical magnetrons that can move, with a controlled speed, along the axis of the SRF cavity to coat the inside surface of the cavity. The design of the sputter coater is discussed, along with its performance. Initially, a sample holder that allows coating on flat substrates at positions similar to the equator and beam tubes of a 2.6 GHz SRF cavity was used to test conditions for fabricating Nb 3 Sn layers. Multilayers of Nb and Sn were sequentially sputtered on flat Nb and sapphire substrates mounted on the equivalent positions of the cavity's beam tubes and the equator using the two identical cylindrical magnetrons. Then, the Nb/Sn multilayers were annealed at 950 °C for 3 h. Here, the ~1.2 μm thick Nb 3 Sn film did not show any other Nb–Sn compounds and had a superconducting transition temperature of 17.61–17.76 K. The 2.6 GHz SRF cavity was coated using similar conditions as flat samples. Cryogenic RF testing of the Nb 3 Sn-coated cavity demonstrated a quality factor of 3.2 × 10 8 at an accelerating gradient of 5 MV/m at 4.4 K.
43 PARTICLE ACCELERATORS↗
A fast computational framework for the design of solvent-based plastic recycling processes
Multicomponent plastics cannot be processed using mechanical recycling technologies, hindering efforts to deal with plastic waste. Multicomponent plastics include multilayer plastic films, which are widely used for food and healthcare packaging. Multilayer films combine several layers (potentially dozens) of different polymers to protect products from external factors (e.g., oxygen, water, temperature, shock, and light). Solvent-based separation processes have emerged as a promising alternative to recycle these complex materials. For instance, the Solvent-Targeted Recovery and Precipitation (STRAP TM ) process uses sequential solvent washes to selectively dissolve and separate constituent polymers from multicomponent plastic waste, including films. STRAP TM process design (separation sequence, type of solvents, and operating conditions) changes significantly depending on the design of the multilayer plastic film (e.g., number, types, and proportions of polymers). The ability to quickly quantify the economic and environmental benefits of diverse STRAP TM process designs is essential to accelerate the development of sustainable recycling processes and more recyclable multilayer film products. In this work, we present a fast computational framework that integrates molecular-scale models, process modeling, and techno-economic and life cycle analysis to quickly evaluate STRAP TM designs. The computational framework is general and can be used to study the processing of complex multilayer plastic waste streams that contain many layers. Furthermore, we highlight the different uses of the framework via targeted case studies.
Computational framework↗
Effects of a Layered Morphology on Drip Suppression in Burning Polymers
Fire safety in polymers is critically important with products such as textiles and consumer goods, as well as materials used in construction, aerospace, transportation, and furniture. Additives used as anti-dripping and flame-retardant agents impose acute human health issues and have negative environmental impacts. With a focus on developing additive-free solutions, here we used multilayer coextrusion to fabricate layered polyethylene/polypropylene (PE/PP) films and investigated the effect of a layered morphology on dripping and burning rates. The experimental results for multilayered PE/PP samples were compared to control groups of melt blended PE/PP samples. The multilayer configuration provides two significant advantages: 154% delay in the time to the first drip and up to 87% reduction in the number of drips compared to the value for the melt blended samples with no additives. PE/PP blends with up to 2 wt % polytetrafluoroethylene, a commonly used anti-dripping agent in the industry, showed only 85% delay in the time to the first drip and about 60% reduction in the number of drips. We discovered a linear relationship between film thickness and burning rate, which allows for the use of the volumetric burning rate to normalize the effect of film thickness. No benefit in the burning rate was observed when comparing multilayered structures and conventional melt blended architectures or blends with PTFE. Annealing studies and transmission electron microscopy at areas close to the combustion zones confirmed that higher extensional viscosities induced by the layered structures and morphological changes due to the layer breakup play an important role in reducing dripping. By combining the first drip time and overall drip numbers, a parameter, “dripping index”, was defined to establish a fire safety map to simplify material comparisons. This study demonstrates that a multilayer film geometry can provide an additive-free solution to yield control over fire safety parameters in polymers.
36 MATERIALS SCIENCE↗
Rare-Earth Permanent Magnet SmCo 5 for Chiral Interfacial Spin-Orbitronics
Interfacially asymmetric magnetic multilayers made of heavy metal/ferromagnet have attracted considerable attention in the spintronics community for accommodating spin-orbit torques (SOTs) and meanwhile for hosting chiral spin textures. In these multilayers, the accompanied interfacial Dzyaloshinskii–Moriya interaction (iDMI) permits the formation of Néel-type spin textures. While significant progresses have been made in Co, CoFeB, Co 2 FeAl, CoFeGd based multilayers, it would be intriguing to identify new magnetic multilayers that could enable spin-torque controllability and meanwhile host nanoscale skyrmions. In this report, first, thin films made of permanent magnet SmCo 5 with perpendicular magnetic anisotropy are synthesized, in which the deterministic SOT switching, enabled by the spin Hall effect, in Pt/SmCo 5 /Ta trilayer is demonstrated. Further, the stabilization of room-temperature skyrmions with diameters ≈100 nm in [Pt/SmCo 5 /Ta] 15 , together with a skyrmionium-like spin texture in [Pt/SmCo 5 /Ir] 15 multilayers is shown. Based on the material specific parameters, micromagnetic simulations are also carried out. The results confirm the presence of chiral spin textures in this new material family. Through interfacial engineering, the results thus demonstrate that rare earth permanent magnets could be a new platform for studying interfacial chiral spintronics.
36 MATERIALS SCIENCE↗
Monte Carlo simulation of shielding designs for a cabinet form factor preclinical MV–energy photon FLASH radiotherapy system
Purpose: A preclinical MV-energy photon FLASH radiotherapy system is being designed at Stanford and SLAC National Accelerator Laboratory. Because of the higher energy and dose rate compared to conventional kV-energy photon laboratory-scale irradiators, adequate shielding in a stand-alone cabinet form factor is more challenging to achieve. We present a Monte Carlo simulation of multilayered shielding for a compact self-shielding system without the need for a radiation therapy vault. Methods: A multilayered shielding approach using multiple alternating layers of high-Z and low-Z materials is applied to the self-shielded cabinet to effectively mitigate the secondary radiation produced and to allow the device to be housed in a Controlled Radiation Area outside of a radiation vault. The multilayered shielding approach takes advantage of the properties of high-Z and low-Z radiation shielding materials such as density, cross-section, atomic number of the shielding elements, and products of radiation interactions within each layer. The Monte Carlo radiation transport code, FLUKA, is used to simulate the total effective dose produced by the operation. Results: The multilayered shielding designs proposed and simulated produced effective dose rates significantly lower than monolayer designs with the same total material thickness at the regulatory boundary; this is accomplished through the manipulation of the locations where secondary radiation is produced and reactions due to material properties such as neutron back reflection in hydrogen. Borated polyethylene at 5 wt% significantly increased the shielding performance as compared to regular polyethylene, with the magnitude of the reduction depending upon the order of the shielding material. Conclusions: The multilayered shielding provides a path for shielding preclinical FLASH systems that deliver MV-energy bremsstrahlung photons. Furthermore, this approach promises to be more efficient with respect to the shielding material mass and space claim as compared to shielded vaults typically required for clinical radiation therapy with MV photons.
62 RADIOLOGY AND NUCLEAR MEDICINE↗
Performance simulation of the soft gamma-ray concentrator
The soft gamma-ray concentrator is a telescope mission concept utilizing a suitable arrangement of bent multilayer structures of alternating low- and high-density materials. This lens is able to channel gamma-ray photons via total external reflection and concentrate the incident radiation to a point. The channeling technique offers the potential for concentrating gamma rays with focal lengths <10 m and energies >100 keV, beyond the reach of current grazing-incidence hard x-ray mirrors. For the performance estimation of such an instrument, we have developed a flexible set of computer modeling tools to compute the optical properties of multilayer structures, predict the channeling efficiency for a given multilayer configuration, and aid in the optimization of potential gamma-ray concentrator-based telescope designs. This modeling includes the multilayer optical properties calculated by the IMD software, the ray tracing using an IDL code, and the focal plane detector simulation by MEGAlib. We illustrate the potential of this approach by presenting simulated astronomical observations from a balloon-borne platform. The final result, including simulated effective area, instrument sensitivity, and polarization performance, shows that the gamma-ray concentrator will provide greatly increased sensitivity for next-generation soft gamma-ray missions with modest cost and complexity.
47 OTHER INSTRUMENTATION↗
Helium Bubbles and Blistering in a Nanolayered Metal/Hydride Composite
Helium is insoluble in most metals and precipitates out to form nanoscale bubbles when the concentration is greater than 1 at.%, which can alter the material properties. Introducing controlled defects such as multilayer interfaces may offer some level of helium bubble management. This study investigates the effects of multilayered composites on helium behavior in ion-implanted, multilayered ErD 2 /Mo thin film composites. Following in-situ and ex-situ helium implantation, scanning and transmission electron microscopy showed the development of spherical helium bubbles within the matrix, but primarily at the layer interfaces. Bubble linkage and surface blistering is observed after high fluence ex-situ helium implantation. These results show the ability of metallic multilayers to alter helium bubble distributions even in the presence of a hydride layer, increasing the lifetime of materials in helium environments.
36 MATERIALS SCIENCE↗
Synergetic Effects of Soil Organic Matter Components During Interactions with Minerals
Mineral-associated soil organic matter (SOM) is critical for stabilizing organic carbon and mitigating climate change. However, mineral-SOM interactions at the molecular scale, particularly synergetic adsorption through organic-organic interaction on the mineral surface known as organic multilayering, remain poorly understood. This study investigates the impact of organic multilayering on mineral-SOM interactions, by integrating macroscale experiments and molecular-scale simulations that assess the individual and sequential adsorption of major SOM compounds – lauric acid (lipid), pentaglycine (amino acid), trehalose (carbohydrate), and lignin onto soil minerals. Ferrihydrite, Al-hydroxide, and calcite are exposed to SOM compounds to determine adsorption affinities and binding energies. Results show that lauric acid has 20-40 times higher K d than pentaglycine, following the order K d (ferrihydrite) > K d (Al-hydroxide) >> K d (calcite). Molecular-scale simulations confirm that lauric acid has a higher binding energy (30.8 kcal/mol) on ferrihydrite than pentaglycine (6.0 kcal/mol), attributed to lipid hydrophobicity. The lower binding energy of pentaglycine results from its hydrophilic amide groups, facilitating partitioning into water. Sequential experiments examine how the first layer of lipid or amino acid affects the adsorption of carbohydrate/lignin, which show little or no individual adsorption affinities. Macroscale results reveal that lipid and amino acid adsorption induce ferrihydrite particle repulsion increasing reactive surface area and enhancing carbohydrate/lignin adsorption independently and synergistically through organic multilayering. Molecular-scale results reveal that amino acid adsorbed on ferrihydrite interacts more readily with lignin macroaggregates (preformed in solution) than with individual lignin units, indicating organic multilayering via H-bonding. Further, these findings reveal the molecular mechanisms of SOM-mineral interactions, crucial for enhancing soil carbon stabilization.
54 ENVIRONMENTAL SCIENCES↗
Magnetism and interlayer bonding in pores of Bernal-stacked hexagonal boron nitride
When single-layer h-BN is subjected to a high-energy electron beam, triangular pores with nitrogen edges are formed. Because of the broken sp 2 bonds, these pores are known to possess magnetic states. Here, we report on the magnetism and electronic structure of triangular pores as a function of their size. Moreover, in the Bernal-stacked h-BN (AB-h-BN), multilayer pores with parallel edges can be created, which is not possible in the commonly fabricated multilayer AA'-h-BN. Given that these pores can be manufactured in a well-controlled fashion using an electron beam, it is important to understand the interactions of pores in neighboring layers. We find that in certain configurations, the edges of the neighboring pores remain open and retain their magnetism, and in others, they form interlayer bonds. We present a comprehensive report on these configurations for small nanopores. We find that at low temperatures, these pores have near degenerate magnetic configurations, and may be utilized in magnetoresistance and spintronics applications. In the process of forming larger multilayer nanopores, interlayer bonds can form, reducing the magnetization. Yet, unbonded parallel multilayer edges remain available at all sizes. Understanding these pores is also helpful in a multitude of applications such as DNA sequencing and quantum emission.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Thermal model for time-domain thermoreflectance experiments in a laser-flash geometry
Time-domain thermoreflectance (TDTR) is a well-established pump–probe method for measuring thermal conductivity and interface conductance of multilayers. Interpreting signals in a TDTR experiment requires a thermal model. In standard front/front TDTR experiments, both pump and probe beams typically irradiate the surface of a multilayer. As a result, existing thermal models for interpreting thermoreflectance experiments assume that the pump and probe beams both interact with the surface layer. Here, we present a frequency-domain solution to the heat-diffusion equation of a multilayer in response to nonhomogeneous laser heating. This model allows analysis of experiments where the pump and probe beams irradiate opposite sides of a multilayer. We call such a geometry a front/back experiment to differentiate such experiments from standard TDTR experiments. As an example, we consider a 60nm amorphous Si film. We consider how signals differ in a front/front vs front/back geometry and compare thermal model predictions to experimental data.
Peng, Wanyue↗
Shielding Analysis of a Preclinical Bremsstrahlung X-ray FLASH Radiotherapy System within a Clinical Radiation Therapy Vault
A preclinical radiotherapy system producing FLASH dose rates with 12 MV bremsstrahlung x rays is being developed at Stanford University and SLAC National Accelerator Laboratory. Because of the high expected workload of 6,800 Gy w –1 at the isocenter, an efficient shielding methodology is needed to protect operators and the public while the preclinical system is operated in a radiation therapy vault designed for 6 MV x rays. Here, in this study, an analysis is performed to assess the shielding of the local treatment head and radiation vault using the Monte Carlo code FLUKA and the empirical methodology given in the National Council on Radiation Protection and Measurements Report 151. Two different treatment head shielding designs were created to compare single-layer and multilayer shielding methodologies using high-Z and low-Z materials. The multilayered shielding methodology produced designs with a 17% reduction in neutron fluence leaking from the treatment head compared to the single layered design of the same size, resulting in a decreased effective dose to operators and the public. The conservative assumptions used in the empirical methods can lead to over-shielding when treatment heads use polyethylene or multilayered shielding. High-Z/Low-Z multilayered shielding optimized via Monte Carlo is shown to be effective in the case of treatment head shielding and provide more effective shielding design for external beam radiotherapy systems that use 12 MV bremsstrahlung photons. Modifications to empirical methods used in the assessment of MV radiotherapy systems may be warranted to capture the effects of polyethylene in treatment head shielding.
61 RADIATION PROTECTION AND DOSIMETRY↗
Steam oxidation of ytterbium disilicate environmental barrier coatings with and without a silicon bond coat
The current generation of multilayer Si/Yb 2 Si 2 O 7 environmental barrier coatings (EBCs) are temperature limited by the melting point of Si, 1414°C. To investigate higher temperature EBCs, the cyclic steam oxidation of EBCs comprised of a single layer of ytterbium disilicate (YbDS) was compared to multilayered Si/YbDS EBCs, both deposited on SiC substrates using atmospheric plasma spray. In this work, after 500 1-h cycles at 1300°C in 90 vol%H2O-10 vol%air with a gas velocity of 1.5 cm/s, both multilayer Si/YbDS and single layer YbDS grew thinner silica scales than bare SiC, with the single layer YbDS forming the thinnest scale. Both coatings remained fully adherent and showed no signs of delamination. Silica scales formed on the single layer coating were significantly more homogeneous and possessed a markedly lower degree of cracking compared to the multilayered EBC. The single layer EBC also was exposed at 1425°C in steam with a gas velocity of 14 cm/s in an alumina reaction tube. The EBC reduced specimen mass loss compared to bare SiC but formed an extensive 2nd phase aluminosilicate reaction product. A similar reaction product was observed to form on some regions of the bare SiC specimen and appeared to partially inhibit silica volatilization. The 1425°C steam exposures were repeated with a SiC reaction tube and no 2nd phase reaction product was observed to form on the single layer EBC or bare SiC.
36 MATERIALS SCIENCE↗
3rd harmonic magnetometry assessment of NbTiN-based SIS structures
In the quest for alternative superconducting materials to bring accelerator cavity performance beyond the bulk niobium (Nb) intrinsic limits, a promising concept proposes that superconductor-insulator-superconductor (SIS) thin film structures can delay magnetic flux penetration in accelerator cavities to higher fields [1]. NbTiN is a candidate superconductor for such structures. We have demonstrated high quality NbTiN and AlN deposited by reactive direct current magnetron sputtering (DCMS), both for individual layers and multilayers. Interface quality has been assessed for bi-layer stacks with various NbTiN and AlN thicknesses from 500 and 30 nm down to 3 and 1 nm. These SIS structures show continued sharp interfaces. The Hfp enhancement of the films was examined with 3rd harmonic magnetometry. The system was designed and built in an ongoing collaboration with CEA Saclay. It can measure 1? to 2? samples on a temperature controlled stage. This contribution presents the assessment of the first penetration field enhancement with 3rd harmonic magnetometry for standalone films and multilayer nanostructures.
Valente, Anne-Marie↗
Roll-to-Roll Advanced Materials Manufacturing DOE Laboratory Collaboration (FY2020 Final Report)
R2R processing is used to manufacture a wide range of products for various applications which span many industrial business sectors. The overall R2R methodology has been in use for decades and this continuous technique traditionally involves deposition of material(s) onto moving webs, carriers or other continuous belt-fed or conveyor-based processes that enable successive steps to build a final version which serves to support the deposited materials. Established methods that typify R2R processing include tape casting, silk-screen printing, reel-to-reel vacuum deposition/coating, and R2R lithography. Products supported by R2R manufacturing include micro-electronics, electro-chromic window films, PVs, fuel cells for energy conversion, battery electrodes for energy storage, and barrier and membrane materials. Due to innovation in materials and process equipment, high-quality yet very low-cost multilayer technologies have the potential to be manufactured on a very cost-competitive basis. To move energy-related products from high-cost niche applications to the commercial sector, the means must be available to enable manufacture of these products in a cost-competitive manner that is affordable. Fortunately, products such as fuel cells, thin- and mid-film PVs, batteries, electrochromic and piezoelectric films, water separation membranes, and other energy saving technologies readily lend themselves to manufacture using R2R approaches. However, more early-stage research is needed to solve the challenge of linking the materials (particles, polymers, solvents, additives) used in ink and slurry formulations and the coating and drying processes to the ultimate performance of the final R2R product, especially for a process that uses multiple layers of deposition to achieve the end product. To solve the problems associated with these challenges, the R2R Collaboration is executing a research program with outcomes that will ultimately link modeling, processing, metrology and defect detection tools, thereby directly relating the properties of constituent particles and processing conditions to the performance of final devices. This collaborative approach was designed to foster identification and development of materials and processes related to R2R for clean-energy materials development. Using computational and experimental capabilities by acknowledged subject matter experts within the supported National Laboratory system, this project leverages the capabilities and expertise at each of five National Laboratories to further the development of multilayer technologies that will enable high-volume, cost-competitive platforms. A typical R2R process has three steps: (1) mixing of particles and various constituents in a slurry, (2) coating of the ink/slurry mixture on a substrate, and (3) drying/curing and processing of the coating. Final performance of devices made via R2R processes is dependent on the active materials (e.g., electrochemical particles in battery or fuel cell electrodes) and the device structure that stems from the governing component interactions within the various steps. However, a fundamental understanding of the underlying mechanisms and phenomena is still lacking, which is why industrial-scale R2R process development and manufacturing is still largely empirical in nature. The FY 2019 through FY 2021 program addresses aspects of the following two targets from the AMO Multi-Year Program Plan: (1) Target 8.1 Develop technologies to reduce the cost per manufactured throughput of continuous R2R manufacturing processes. (A) Increasing throughput of R2R processes by 5 times for batteries (to 50 square feet per minute (50 ft 2 /min)) and capacitors and 10 times for printed electronics and the manufacture of other substrates and MEs used in support of these products. (B) Developing resolution capabilities to enable registration and alignment that will detect, align, and co-deposit multiple layers of coatings and print < 1-micron (1 µm) features using continuous process scalable for commercial production. (C) Developing scalable and reliable R2R processes for solution deposition of ultra-thin (<10 nm) films for active and passive materials. (D) Develop in-line multilayer coating technology on thin films with yields greater than 95%. (2) Target 8.2 Develop in-line instrumentation tools that will evaluate the quality of single and multilayer materials in-process. (A) Developing in-line QC technologies and methodologies for real-time identification of defects and expected product properties “in-use/application” during continuous processing at all size-scales with a focus on the “micro” and “nano” scale traces, lines, and devices, i.e., <1 μm at 300 ft./min for R2R processing in air and <10 nm at 20 ft./min for vacuum (B) Developing technologies to increase the measurement frequency of surface rheology without significant cost increases with a goal of a 10-nanometer in-line profilometry at a production rate of 100,000 square millimeters per minute (100,000 mm 2 /min).
42 ENGINEERING↗