SEARCH · Engineering Papers

Results for “mixed conduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

All sources NASA NTRS DOE OSTI

NASA NTRS2001

Source Identification and Location Techniques

Mr. Weir presented source location results obtained from an engine test as part of the Engine Validation of Noise Reduction Concepts program. Two types of microphone arrays were used in this program to determine the jet noise source distribution for the exhaust from a 4.3 bypass ratio turbofan engine. One was a linear array of 16 microphones located on a 25 ft. sideline and the other was a 103 microphone 3-D "cage" array in the near field of the jet. Data were obtained from a baseline nozzle and from numerous nozzle configuration using chevrons and/or tabs to reduce the jet noise. Mr. Weir presented data from two configurations: the baseline nozzle and a nozzle configuration with chevrons on both the core and bypass nozzles. This chevron configuration had achieved a jet noise reduction of 4 EPNdB in small scale tests conducted at the Glenn Research Center. IR imaging showed that the chevrons produced significant improvements in mixing and greatly reduced the length of the jet potential core. Comparison of source location data from the 1-D phased array showed a shift of the noise sources towards the nozzle and clear reductions of the sources due to the noise reduction devices. Data from the 3-D array showed a single source at a frequency of 125 Hz. located several diameters downstream from the nozzle exit. At 250 and 400 Hz., multiple sources, periodically spaced, appeared to exist downstream of the nozzle. The trend of source location moving toward the nozzle exit with increasing frequency was also observed. The 3-D array data also showed a reduction in source strength with the addition of chevrons. The overall trend of source location with frequency was compared for the two arrays and with classical experience. Similar trends were observed. Although overall trends with frequency and addition of suppression devices were consistent between the data from the 1-D and the 3-D arrays, a comparison of the details of the inferred source locations did show differences. A flight test is planned to determine if the hardware tested statically will achieve similar reductions in flight.

Weir, Donald↗

NASA NTRS2020

Coordinated NanoSIMS and TEM Analysis of a Large 26Mg-Rich AGB Silicate from the Meteorite Hills 00426 CR2 Chondrite

Silicates are one of the most abundant presolar phases around evolved stars, in the inter-stellar medium (ISM), and in our Solar System. These grains afford the opportunity for O, Si, Mg, Fe, and Ca isotopic analyses to constrain stellar nucleosynthetic and mixing processes, and Galactic chemical evolution (GCE). While Mg and Fe isotopic studies have been successfully conducted on presolar silicates, isotopic analyses beyond O and Si are often hampered by the small grain sizes (average ~250 nm). This also makes coordinated mineral and chemical characterization challenging. These studies provide insight into the dust condensation conditions as well as subsequent alteration in the ISM and/or the Solar System. TEM studies of presolar silicates have shown that they are much more mineralogically and chemically diverse than other presolar phases [1 and references therein]. Large (>500nm) presolar silicate grains are rare, but they allow for detailed isotopic, mineral, and chemical characterization. We identified a large presolar silicate grain in the MET 00426 CR2 chondrite and report the O, Si, Mg, and Fe isotopic compositions and TEM study of this grain.

Nguyen, A. N.↗

NASA NTRS1974

Effect of interjet spacing on mixing of multiple coaxial jets in supersonic flow

An experimental and analytical investigation of strut-mounted, four-nozzle, downstream facing, gaseous fuel injector assembly was conducted in a Mach 4 air-stream with P = 154 psia and T sub o 520 R. Helium was used as the injectant, and the interjet spacing (S/D) was the main parameter varied. The principal data are in the form of Helium concentration profiles at seven axial stations, Mach number distributions at three axial stations and schlieren photographs of the flow field at different interjet spacings. An approximate analysis was developed based upon a linearization in the Von Mises plane, Crocco integrals for the temperature and concentrations fields and an eddy viscosity model. Good agreement with the data was achieved. It was found that, at these conditions, interjet spacing has an effect on mixing only up to S/D of approximately 2.5, with concentration of injectant becoming smaller as S/D is increased, and the Mach number downstream of the injector tends to decrease with decreasing S/D.

Lorber, A. K.↗

NASA NTRS1993

Optimization of circular orifice jets mixing into a heated cross flow in a cylindrical duct

To examine the mixing characteristics of circular jets in an axisymmetric can geometry, temperature measurements were obtained downstream of a row of cold jet injected into a heated cross stream. The objective was to obtain uniform mixing within one duct radius downstream of the leading edge of the jet orifices. An area weighted standard deviation of the mixture fraction was used to help quantify the degree of mixedness at a given plane. Non-reacting experiments were conducted to determine the influence of the number of jets on the mixedness in a cylindrical configuration. Results show that the number of orifices significantly impacts the mixing characteristics of jets injected from round hole orifices in a can geometry. Optimum mixing occurs when the mean jet trajectory aligns with the radius which divides the cross sectional area of the can into two equal parts at one mixer radius downstream of the leading edge of the orifice. The optimum number of holes at momentum-flux ratios of 25 and 52 is 10 and 15 respectively.

Kroll, J. T.↗

NASA NTRS1993

Optimization of circular orifice jets mixing into a heated crossflow in a cylindrical duct

Kroll, J. T.↗

NASA NTRS1992

Reduced thermal conductivity due to scattering centers in p-type SiGe alloys

Spark erosion was used to produce ultra-fine particles of SiGe thermoelectric material and boron nitride, an inert phonon-scattering material. A homogeneous powder was made by mixing the two powders. The mixture was hot pressed to produce a thermoelectric material with uniformity dispersed, ultra-fine, inert, phonon-scattering centers. It is shown that, in samples with inert boron nitride or silicon nitride, thermal conductivity of a SiGe alloy can be reduced by about 25 percent while maintaining the electrical properties of the samples. Annealing of all the samples at 1525 K caused grain growth to over a micron, eliminating the detrimental effect attributable to small grains. Only in the sample with boron nitride the thermal conductivity did remain well below that for standard p-type SiGe (about 25 percent), while the electrical resistivity and Seebeck coefficient were very close to the values for standard p-type 80/20 SiGe.

Beaty, John S.↗

NASA NTRS2019

CFD Jet Mixing Model Validation against Zero-Boil-Off Tank (ZBOT) Microgravity Experiment

The Zero-Boil-Off Tank (ZBOT) experiments are a series of small scale two-phase fluids physics experiments conducted aboard the International Space Station (ISS) in 2017. A goal of these experiments is to study various fundamental fluid flow, heat and mass transport, and phase change phenomena that control storage tank pressurization and pressure control in microgravity. In this paper, results of a state-of-the-art two-phase CFD storage tank model are presented and validated against jet mixing data provided by microgravity ZBOT experiments. Jet-ullage interaction was studied in the experiment for different jet speeds representing different flow regimes, and tank fill levels. Effects of various physical parameters, such as, jet angle, gravitational acceleration and surface tension value were investigated. Computational parameters, such as turbulence and surface tension models and interface capturing scheme, affecting jet-ullage interaction were also studied. Computational results were compared to experimental results for model validation.

Mixing↗

NASA NTRS1990

Corrections regarding the Lellouch et al. (1989) analysis of Mars atmospheric C-12O and C-13O spectra

Lellouch et al. (1989) obtained atmospheric CO mixing ratios from Martian C-12O and C-13O microwave spectra that were 3-5 times greater than the Kaplan et al. (1969) IR measurememts; they also inferred a factor-of-2 increase in atmospheric CO abundance between September, 1986 and January, 1987. A reanalysis has been conducted of the Lellouch material, and more detailed treatment of the radiative transfer analysis indicates that its observations are consistent with the Kaplan CO volume mixing ratio determination. It is also ascertained that the Lellouch atmospheric temperature profiles are in error, with no evidence being found for the extreme temperature inversions inferred for the lowest 5 km of the Martian atmosphere.

Clancy, R. Todd↗

NASA NTRS2019

CFD Jet Mixing Model Validation Against Zero-Boil-Off Tank (ZBOT) Microgravity Experiment

The Zero-Boil-Off Tank (ZBOT) experiments are a series of small scale two-phase fluids physics experiments conducted aboard the International Space Station (ISS) in 2017. A goal of these experiments is to study various fundamental fluid flow, heat and mass transport, and phase change phenomena that control storage tank pressurization and pressure control in microgravity. In this paper, results of a state-of-the-art two-phase CFD (Computational Fluid Dynamics) storage tank model are presented and validated against jet mixing data provided by microgravity ZBOT experiments. Jet-ullage interaction was studied in the experiment for different jet speeds representing different flow regimes, and tank fill levels. Effects of various physical parameters, such as, jet angle, gravitational acceleration and surface tension value were investigated. Computational parameters, such as turbulence and surface tension models and interface capturing scheme, affecting jet-ullage interaction were also studied. Computational results were compared to experimental results for model validation.

Turbulence↗

NASA NTRS1985

Mixed-mode cyclic debonding of adhesively bonded composite joints

A combined experimental-analytical investigation to characterize the cyclic failure mechanism of a simple composite-to-composite bonded joint is conducted. The cracked lap shear (CLS) specimens of graphite/epoxy adherend bonded with EC-3445 adhesive are tested under combined mode 1 and 2 loading. In all specimens tested, fatigue failure occurs in the form of cyclic debonding. The cyclic debond growth rates are measured. The finite element analysis is employed to compute the mode 1, mode 2, and total strain energy release rates (i.e., GI, GII, and GT). A wide range of mixed-mode loading, i.e., GI/GII ranging from 0.03 to 0.38, is obtained. The total strain energy release rate, G sub T, appeared to be the driving parameter for cyclic debonding in the tested composite bonded system.

Rezaizadeh, M. A.↗

NASA NTRS2012

High-Thermal-Conductivity Fabrics

Heat management with common textiles such as nylon and spandex is hindered by the poor thermal conductivity from the skin surface to cooling surfaces. This innovation showed marked improvement in thermal conductivity of the individual fibers and tubing, as well as components assembled from them. The problem is centered on improving the heat removal of the liquid-cooled ventilation garments (LCVGs) used by astronauts. The current design uses an extensive network of water-cooling tubes that introduces bulkiness and discomfort, and increases fatigue. Range of motion and ease of movement are affected as well. The current technology is the same as developed during the Apollo program of the 1960s. Tubing material is hand-threaded through a spandex/nylon mesh layer, in a series of loops throughout the torso and limbs such that there is close, form-fitting contact with the user. Usually, there is a nylon liner layer to improve comfort. Circulating water is chilled by an external heat exchanger (sublimator). The purpose of this innovation is to produce new LCVG components with improved thermal conductivity. This was addressed using nanocomposite engineering incorporating high-thermalconductivity nanoscale fillers in the fabric and tubing components. Specifically, carbon nanotubes were added using normal processing methods such as thermoplastic melt mixing (compounding twin screw extruder) and downstream processing (fiber spinning, tubing extrusion). Fibers were produced as yarns and woven into fabric cloths. The application of isotropic nanofillers can be modeled using a modified Nielsen Model for conductive fillers in a matrix based on Einstein s viscosity model. This is a drop-in technology with no additional equipment needed. The loading is limited by the ability to maintain adequate dispersion. Undispersed materials will plug filtering screens in processing equipment. Generally, the viscosity increases were acceptable, and allowed the filled polymers to still be processed.The novel feature is that fabrics do not inherently possess good thermal conductivity. In fact, fabrics are used for thermal insulation, not heat removal. The technology represents the first material that is a wearable fabric, based on company textiles and materials that will significantly conduct heat.

Chibante, L. P. Felipe↗

NASA NTRSDate not supplied

Designing a Flight Test of a Flight Path Management System for Advanced Air Mobility Research

The National Aeronautics and Space Administration (NASA) has completed a flight test to evaluate the performance of an onboard prototype automation system operating in future high density urban airspace. The test was part of a research investigation of the Urban Air Mobility (UAM) concept, with a focus on a future environment having hundreds of simultaneous operations over a metropolitan area. The complexity of this future UAM airspace may require automation capable of replanning an aircraft’s path in the presence of traffic and other changing constraints. A live-virtual-constructive (LVC) approach was used to conduct the test. Prototype automation technology was integrated into one of the two live aircraft, which were combined with virtual traffic to create a mixed reality environment at the target airspace density. In-flight evaluation enabled verification of the automation’s functions and discovery of any unexpected behaviors resulting from its operation in an actual flight environment. The in-flight evaluation also provided data for validation of air traffic simulations. This paper discusses the design, methodology, and challenges overcome to conduct a successful flight test. Remaining challenges, future work, and recommendations to improve the flight test capability are also discussed.

Advanced Air Mobility↗

NASA NTRS1982

Turbofan forced mixer-nozzle internal flowfield. Volume 2: Computational fluid dynamic predictions

A general program was conducted to develop and assess a computational method for predicting the flow properties in a turbofan forced mixed duct. The detail assessment of the resulting computer code is presented. It was found that the code provided excellent predictions of the kinematics of the mixing process throughout the entire length of the mixer nozzle. The thermal mixing process between the hot core and cold fan flows was found to be well represented in the low speed portion of the flowfield.

Werle, M. J.↗

NASA NTRS1990

Effect of location of aft-mounted nacelles on the longitudinal aerodynamic characteristics of a high-wing transport airplane

As part of a propulsion/airframe integration program at Langley Research Center, tests were conducted in the Langley 16-Foot Transonic Tunnel to determine the effects of locating flow-through mixed flow engine nacelles in several aft underwing positions on the longitudinal aerodynamics of a high wing transport airplane. D-shaped inlet nacelles were used in the test. Some configurations with antishock bodies and with nacelle toe-in were also tested. Data were obtained for a free stream Mach number range of 0.70 to 0.85 and a model angle-of-attack range from -2.5 to 4.0 degrees.

Abeyounis, William K.↗

NASA NTRS1990

Lead-ruthenium pyrochlores as oxygen electrocatalysts

An investigation of lead-ruthenium pyrochlores of the structure Pb2(Ru/2-x/Pb/x/) O7-y for use as oxygen electrocatalysts in alkaline media is discussed. Lead-ruthenium pyrochlore mixed metal oxides were prepared and characterized by X-ray diffraction, BET surface area, dry powder conductivity, and chemical stability. Gas diffusion electrodes were developed specifically for the lead-ruthenium pyrochlore materials. Also investigated were the effects of varying electrode fabrication parameters on the oxygen reduction performance of the lead-ruthenium pyrochlore electrocatalyst. Long-term stability performance was also evaluated. The oxygen reduction performance of the pyrochlore electrocatalyst is considerably higher than that of the state-of-the-art gold-platinum alloy electrocatalyst currently used by NASA. Furthermore, the pyrochlore electrocatalysts are attractive candidates for high-performance pressurized alkaline fuel cells.

Anderson, E. B.↗

NASA NTRS1997

Construction and Modeling of a Controls Testbed

This paper describes the construction and modeling of a control system testbed to be used for the comparison of various control methodologies. We specifically wish to test fuzzy logic control and compare performance of various fuzzy controllers, including Hybrid Fuzzy-PID (HFPID) and Hierarchical Hybrid Fuzzy-PID (HHFPID) to other controllers including localized rate feedback, LQR/LTR, and H2/H(sub infinity). The control problem is that of vibration suppression in a thin plate with inputs coming from accelerometers and outputs going to piezoelectric actuators or 'patches'. A model based on experimental modal analysis of the plate is conducted and compared with an analytical model. The analytical model uses a boundary condition which is a mix of clamped and simply supported.

Nagle, James C.↗

NASA NTRS1991

Thermal Modeling and Analysis of a Cryogenic Tank Design Exposed to Extreme Heating Profiles

A cryogenic test article, the Generic Research Cryogenic Tank, was designed to qualitatively simulate the thermal response of transatmospheric vehicle fuel tanks exposed to the environment of hypersonic flight. One-dimensional and two-dimensional finite-difference thermal models were developed to simulate the thermal response and assist in the design of the Generic Research Cryogenic Tank. The one-dimensional thermal analysis determined the required insulation thickness to meet the thermal design criteria and located the purge jacket to eliminate the liquefaction of air. The two-dimensional thermal analysis predicted the temperature gradients developed within the pressure-vessel wall, estimated the cryogen boiloff, and showed the effects the ullage condition has on pressure-vessel temperatures. The degree of ullage mixing, location of the applied high-temperature profile, and the purge gas influence on insulation thermal conductivity had significant effects on the thermal behavior of the Generic Research Cryogenic Tank. In addition to analysis results, a description of the Generic Research Cryogenic Tank and the role it will play in future thermal structures and transatmospheric vehicle research at the NASA Dryden Flight Research Facility is presented.

Stephens, Craig A.↗

NASA NTRS2005

Evaluation of Aerosol Properties over Ocean from Moderate Resolution Imaging Spectroradiometer (MODIS) during ACE-Asia

The Aerosol Characterization Experiment-Asia (ACE-Asia) was conducted in March-May 2001 in the western North Pacific in order to characterize the complex mix of dust, smoke, urban/industrial pollution, and background marine aerosol that is observed in that region in springtime. The Moderate Resolution Imaging Spectroradiometer (MODIS) provides a large-scale regional view of the aerosol during the ACE-Asia time period. Focusing only on aerosol retrievals over ocean, MODIS data show latitudinal and longitudinal variation in the aerosol characteristics. Typically, aerosol optical depth (tau(sub a)) values at 0.55 micrometers are highest in the 30 deg. - 50 deg. latitude band associated with dust outbreaks. Monthly mean tau(sub a) in this band ranges approx. 0.40-70, although large differences between monthly mean and median values indicate the periodic nature of these dust outbreaks. The size parameters, fine mode fraction (eta), and effective radius (r(sub eff)) vary between monthly mean values of eta = 0.47 and r(sub eff)= 0.75 micrometers in the cleanest regions far offshore to approximately eta = 0.85 and r(sub eff) =.30 micrometers in near-shore regions dominated by biomass burning smoke. The collocated MODIS retrievals with airborne, ship-based, and ground-based radiometers measurements suggest that MODIS retrievals of spectral optical depth fall well within expected error (DELTA tau(sub a) = plus or minus 0.03 plus or minus 0.05 tau(sub a)) except in situations dominated by dust, in which cases MODIS overestimate both the aerosol loading and the aerosol spectral dependence. Such behavior is consistent with issues related to particle nonsphericity. Comparisons of MODIS-derived r(sub eff) with AERONET retrievals at the few occurrences of collocations show MODIS systematically underestimates particle size by 0.2 micrometers. Multiple-year analysis of MODIS aerosol size parameters suggests systematic differences between the year 2001 and the years 2000 and 2002, which are traced to instrumental electronic cross talk. Sensitivity studies show that such calibration errors are negligible in tau(sub a) retrievals but are more pronounced in size parameter retrievals, especially for dust and sea salt.

Chu, D. A.↗