SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The XV-15 aircraft was tested in the Ames 40 by 80 Foot Wind Tunnel for preliminary evaluation of aerodynamic and aeroelastic characteristics prior to flight. The tests were undertaken to investigate the aircraft performance, stability, control and structural loads for flight modes from helicopter through transition and airplane mode up to the tunnel capability of 170 knots. Results from these tests are presented.
Flight test results obtained with the original Mach hold autopilot designed the YF-12C airplane which uses elevator control and a newly developed Mach hold system having an autothrottle integrated with an altitude hold autopilot system are presented. The autothrottle tests demonstrate good speed control at high Mach numbers and high altitudes while simultaneously maintaining control over altitude and good ride qualities. The autothrottle system was designed to control either Mach number or knots equivalent airspeed (KEAS). Excellent control of Mach number or KEAS was obtained with the autothrottle system when combined with altitude hold. Ride qualities were significantly better than with the conventional Mach hold system.
The results of a six degree of freedom (6-DOF) nonlinear Monte Carlo dispersion analysis for the latest glide return to landing site (GRTLS) abort trajectory for the Space Transportation System 1 Flight are presented. For this GRTLS, the number two main engine fails at 262.5 seconds ground elapsed time. Fifty randomly selected simulations, initialized at external tank separation, are analyzed. The initial covariance matrix is a 20 x 20 matrix and includes navigation errors and dispersions in position and velocity, time, accelerometer bias, and inertial platform misalinements. In all 50 samples, speedbrake, rudder, elevon, and body flap hinge moments are acceptable. Transitions to autoland begin before 9,000 feet and there are no tailscrapes. Navigation derived dynamic pressure accuracies exceed the flight control system constraints above Mach 2.5. Three out of 50 landings exceeded tire specification limit speed of 222 knots. Pilot manual landings are expected to reduce landing speed by landing farther downrange.
The loads measured in a wind tunnel on a full-scale tilting proprotor are compared with calculated results. The data consists primarily of oscillatory beamwise bending moments at 35% radial station, oscillatory spindle chord bending moments, and oscillatory pitch link loads. The measured and calculated results as a function of thrust are compared over a range of nacelle angles from 0 to 75 deg, and a range of speeds from 80 to 185 knots.
A coordinated analysis and ground simulator experiment was performed to investigate the effects on single rotor helicopter handling qualities of systematic variations in the main rotor hinge restraint, hub hinge offset, pitch-flap coupling, and blade lock number. Teetering rotor, articulated rotor, and hingeless rotor helicopters were evaluated by research pilots in special low level flying tasks involving obstacle avoidance at 60 to 100 knots airspeed. The results of the experiment are in the form of pilot ratings, pilot commentary, and some objective performance measures. Criteria for damping and sensitivity are reexamined when combined with the additional factors of cross coupling due to pitch and roll rates, pitch coupling with collective pitch, and longitudinal static stability. Ratings obtained with and without motion are compared. Acceptable flying qualities were obtained within each rotor type by suitable adjustment of the hub parameters, however, pure teetering rotors were found to lack control power for the tasks. A limit for the coupling parameter L sub q/L sub p of 0.35 is suggested.
The AD-1 airplane was designed as a low cost, low speed manned research tool to evaluate the flying qualities of the oblique wing concept. The airplane is constructed primarily of foam and fiberglass and incorporates simplicity in terms of the onboard systems. There are no hydraulics, the control system is cable and torque tube, and the electrical systems consist of engine driven generators which power the battery for engine start, cockpit gages, trim motors, and the onboard data system. The propulsion systems consist of two Microturbo TRS-18 engines sea level trust rated at 220 pounds. The airplane weighs approximately 2100 pounds and has a performance potential in the range of 200 knots and an altitude of 15,000 feet.
A flight investigation produced data on performance and rotor loads for a teetering rotor, AH-1G helicopter flown with a main rotor that had the NLR-1T airfoil as the blade section contour. The test envelope included hover, forward flight speeds from 34 to 83 m/sec (65 to 162 knots), and collective fixed maneuvers at about 0.25 tip speed ratio. The data set for each test point describes vehicle flight state, control positions, rotor loads, power requirements, and blade motions. Rotor loads are reviewed primarily in terms of peak to peak and harmonic content. Lower frequency components predominated for most loads and generally increased with increased airspeed, but not necessarily with increased maneuver load factor. Detailed data for an advanced airfoil on an AH-1G are presented.
A NASTRAN model of a UH-1B tail boom that had been designed for another project was used to investigate the effect on structural integrity of simulated projectile damage. Elements representing skin, and sections of stringers, longerons and bulkheads were systematically deleted to represent projectile damage. The structure was loaded in a manner to represent the flight loads that would be imposed on the tail boom at a 130 knot cruise. The deflection of four points on the rear of the tail boom relative to the position of these points for the unloaded, undamaged condition of the tail boom was used as a measure of the loss of structural rigidity. The same procedure was then used with the material properties of the aluminum alloys replaced with the material properties of T300/5208 high strength graphite/epoxy fibrous composite material, (0, + or - 45, 90)s for the skin and (0, + or - 45)s for the longerons, stringers, and bulk heads.
The Quiet Short-Haul Research Aircraft (QSRA), designed to expand the technology base of the upper-surface blowing propulsive-lift principle in order to establish criteria for the U.S. aircraft industry and for advanced STOL aircraft, is considered. The aircraft, which includes a three-axis, single channel, limited authority series type stability augmentation system, and a high-speed data system is described. Also discussed are STOL and acoustic performance, and handling qualities, particularly thrust effects. The QSRA has demonstrated its ability, even with the critical engine inoperative, to approach at 66 knots (wing loading of 83 lb/sq ft) and on a 9 degree glidepath; to maneuver in a 700-ft radius turn, and to land in an FAA field length of 1450 ft (over a 35-ft obstacle).
A design study has been conducted to optimize a single-engine airplane for a high-performance cruise mission. The mission analyzed included a cruise speed of about 300 knots, a cruise range of about 1300 nautical miles, and a six-passenger payload (5340 N (1200 lb)). The purpose of the study is to investigate the combinations of wing design, engine, and operating altitude required for the mission. The results show that these mission performance characteristics can be achieved with fuel efficiencies competitive with present-day high-performance, single- and twin-engine, business airplanes. It is noted that relaxation of the present Federal Aviation Regulation, Part 23, stall-speed requirement for single-engine airplanes facilitates the optimization of the airplane for fuel efficiency.
A flight evaluation was conducted to determine the effects of winglets on the performance and handling qualities of a light, single-engine general aviation airplane. The performance measurements were made with a pace airplane to provide calibrated airspeeds; uncalibrated panel instruments in the test airplane were used to provide additional quantitative performance data. These tests were conducted with winglets on and off during the same day to measure relative performance effects. Handling qualities were evaluated by means of pilot comments. Winglets increased cruise speed 8 knots (5.6 percent) at 3962 m (13,000 ft) density altitude and 51 percent maximum continuous power setting. Maximum speed at 3962 m was virtually unchanged. Rate of climb increased approximately 6 percent, or 0.25 m/sec (50 ft/min), at 1524 m (5000 ft). Stall speed was virtually unchanged. Handling qualities were favorably affected.
Doppler radar measurements of an intense wind shear occurance are discussed. The data suggest the presence of an incredibly strong low level jet outflow component of the microburst event, reaching 60 knots only 50 meters above the surface. Evidence also suggests that microbursts more typically occur in very weak thunderstorms that have hardly reached thunderstorm stage.
The test envelope included hover, forward-flight speed sweeps from 33 to 74 m/sec (65 to 144 knots), and collective-fixed maneuvers at about 0.25 tip-speed ratio. The data set for each test point describes vehicle flight states, control positions, rotor loads, power requirements and blade motions. Rotor loads were reviewed primarily in terms of peak-to-peak and harmonic content. Lower frequency components predominated for most loads and generally increased with increased airspeed, but not necessarily with increased maneuver load factor.
Results from wind tunnel and flight tests investigations for V/STOL aircraft are reviewed. Primary emphasis is given to technical results relating to three types of subsonic aircraft: a quiet STOL aircraft; a tilt rotor aircraft; and a turbofan V/STOL aircraft. Comparison and correlation between theoretical and experimental results and between wind tunnel and flight test results, is made. The quiet STOL aircraft technology results are primarily those derived from the NASA/Boeing Quiet Short Haul Technology (QSRA) program. The QSRA aircraft uses an upper surface blown flap and develops a usable engine-out landing approach lift coefficient of 5.5 and landing distances less than 1,000 ft. The tilt rotor aircraft technology results are those obtained from the NASA/Army/Navy/Bell (XV-15-TRRA) aircraft flight investigations. The TRRA is a twin rotor research aircraft capable of vertical takeoff and landing and cruise speeds of 300 knots. The turbofan V/STOL aircraft technology results are from static ground facility and wind tunnel investigations of a NASA/NAVY/Grumman full scale lift/cruise fan aircraft model, which features two tilting nacelles with TF-34 engines.
The hydrogen burnoff igniter, a pyrotechnic device used to burn off excess hydrogen gas near the Space Shuttle Main Engine (SSME) nozzle, was designed, fabricated, and qualified. Characteristics of the burnoff igniter include a function time of 8 + or - 2 seconds, a minimum three foot flame length at maximum output, and hot particles projected 15 feet when fired directly into or perpendicular to a 34.5 knot wind. The three foot flame length was considered to be of questionable importance, since the hot particles are the media for igniting the hydrogen. Flame temperature is greater than 1500 F.
The slidewire emergency egress system is designed to provide a fast and safe egress means for the shuttle flight crew, passengers, and ground closeout crew in the event of imminent danger while the space vehicle is still on the launch pad. Egress is from the 195 ft. level of the fixed service structure (FSS) to a ground landing area 1200 ft. away from the launch site. The slidewire design is such that the flight crew and passengers can be evacuated to a safe area within two minutes with winds as high as 34 knots from any direction.
The wind tunnel testing of a scale model of a tandem fan nacelle designed for a type (subsonic cruise) V/STOL aircraft configuration is discussed. The performance for the isolated front inlet and for the combined front and aft inlets is reported. Model variables include front and aft inlets with aft inlet variations of short and long aft inlet cowls, with a shaft simulator and diffuser vortex generators, cowl lip fillets, and nacelle strakes. Inlet pressure recovery, distortion, and inlet angle-to-attack separation limits were evaluated at tunnel velocity from 0 to 240 knots, angles-of-attack from -10 to +40 degrees and inlet flow rates corresponding to throat Mach number from 0.0 to 0.6. Combined nacelle pitch and yaw runs up to 30 deg. were also made.
The feasibility of the application of advanced state-of-the-art high lift STOL aircraft in the aircraft carrier environment was evaluated using the NASA Quiet Short-Haul Research Aircraft (QSRA). The QSRA made repeated unarrested landings and free deck takeoffs from the USS Kitty Hawk while being flown by three pilots of significant different backgrounds. The exercise demonstrated that the USB propulsive lift technology presents no unusual problems in the aircraft carrier environment. Optimum parameters for landing the QSRA were determined from the shore-based program; these proved satisfactory during operations aboard ship. Correlation of shipboard experience with shore-based data indicates that both free deck takeoffs and unarrested landings could be conducted with zero to 35 knots of wind across the deck of an aircraft carrier the size of the USS Kitty Hawk.