Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “interval analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

A geostatistical analysis of small-scale spatial variability in bacterial abundance and community structure in salt marsh creek bank sediments

Small-scale variations in bacterial abundance and community structure were examined in salt marsh sediments from Virginia's eastern shore. Samples were collected at 5 cm intervals (horizontally) along a 50 cm elevation gradient, over a 215 cm horizontal transect. For each sample, bacterial abundance was determined using acridine orange direct counts and community structure was analyzed using randomly amplified polymorphic DNA fingerprinting of whole-community DNA extracts. A geostatistical analysis was used to determine the degree of spatial autocorrelation among the samples, for each variable and each direction (horizontal and vertical). The proportion of variance in bacterial abundance that could be accounted for by the spatial model was quite high (vertical: 60%, horizontal: 73%); significant autocorrelation was found among samples separated by 25 cm in the vertical direction and up to 115 cm horizontally. In contrast, most of the variability in community structure was not accounted for by simply considering the spatial separation of samples (vertical: 11%, horizontal: 22%), and must reflect variability from other parameters (e.g., variation at other spatial scales, experimental error, or environmental heterogeneity). Microbial community patch size based upon overall similarity in community structure varied between 17 cm (vertical) and 35 cm (horizontal). Overall, variability due to horizontal position (distance from the creek bank) was much smaller than that due to vertical position (elevation) for both community properties assayed. This suggests that processes more correlated with elevation (e.g., drainage and redox potential) vary at a smaller scale (therefore producing smaller patch sizes) than processes controlled by distance from the creek bank. c2002 Federation of European Microbiological Societies. Published by Elsevier Science B.V. All rights reserved.

Non-NASA Center↗

Robustness-Based Design Optimization Under Data Uncertainty

This paper proposes formulations and algorithms for design optimization under both aleatory (i.e., natural or physical variability) and epistemic uncertainty (i.e., imprecise probabilistic information), from the perspective of system robustness. The proposed formulations deal with epistemic uncertainty arising from both sparse and interval data without any assumption about the probability distributions of the random variables. A decoupled approach is proposed in this paper to un-nest the robustness-based design from the analysis of non-design epistemic variables to achieve computational efficiency. The proposed methods are illustrated for the upper stage design problem of a two-stage-to-orbit (TSTO) vehicle, where the information on the random design inputs are only available as sparse point and/or interval data. As collecting more data reduces uncertainty but increases cost, the effect of sample size on the optimality and robustness of the solution is also studied. A method is developed to determine the optimal sample size for sparse point data that leads to the solutions of the design problem that are least sensitive to variations in the input random variables.

Zaman, Kais↗

The isotopic composition of cosmic-ray helium from 123 to 279 MeV per nucleon - A new measurement and analysis

A description is given of an experiment which was designed to measure the spectra and composition of cosmic-ray hydrogen and helium isotopes in the interval 120-280 MeV per nucleon to compare with the recent values observed at low energies and also with the only earlier measurement in this high-energy regime. The results presented were obtained during a high-altitude balloon flight from Thompson, Manitoba, in 1973 August. This flight occurred during the period in which the presence of the anomalous component in the helium spectrum became apparent, and provides the opportunity of determining whether this component extends to higher energies than those studied by satellite experiments. The results place an upper limit on the flux of 'anomalous' He-4 (which appeared at low energy in 1972) of at most 15% in the energy range of this experiment, and combined with the low-energy observations of the Chicago group, show an energy dependence of the average ratio of the helium isotopes in the modulated cosmic rays which is difficult to reconcile with current modulation models.

Leech, H. W.↗

Backward elastic pd scattering at 316, 364, 470 and 590 MeV

Preliminary results are reported from a part of the data obtained at the NASA Space Radiation Effect Laboratory for the elastic scattering of protons by deuterons in the backward hemisphere. The data is averaged over a proton angle interval which corresponds to the angular resolution on the correlation angle, given the proton bin used in the data analysis.

Alder, J. C.↗

Ion and laser microprobes applied to the measurement of corrosion produced hydrogen on a microscopic scale.

Use of an ion microprobe and a laser microprobe to measure concentrations of corrosion-produced hydrogen on a microscopic scale. Hydrogen concentrations of several thousand ppm were measured by both analytical techniques below corroded and fracture surfaces of hot salt stress corroded titanium alloy specimens. This extremely high concentration compares with only about 100 ppm hydrogen determined by standard vacuum fusion chemical analyses of bulk samples. Both the ion and laser microprobes were used to measure hydrogen concentration profiles in stepped intervals to substantial depths below the original corroded and fracture surfaces. For the ion microprobe, the area of local analysis was 22 microns in diameter and for the laser microprobe, the area of local analysis was about 300 microns in diameter. The segregation of hydrogen below fracture surfaces supports a previously proposed theory that corrosion-produced hydrogen is responsible for hot salt stress corrosion embrittlement and cracking of titanium alloys. These advanced analytical techniques suggest great potential for many areas of stress corrosion and hydrogen embrittlement research, quality control, and field inspection of corrosion problems. For example, it appears possible that a contour map of hydrogen distribution at notch roots and crack tips could be quantitatively determined. Such information would be useful in substantiating current theories of stress corrosion and hydrogen embrittlement.

Gray, H. R.↗

Investigation of ground reflection and impedance from flyover noise measurements

An extensive series of flyover noise tests was conducted for the primary purpose of studying meteorological effects on propagation of aircraft noise. The test airplane, a DC 9-10, flew several level-flight passes at various heights over a taxiway. Two microphone stations were located under the flight path. A total of 37 runs was selected for analysis and processed to obtain a consistant set of 1/3 octave band sound pressure levels at half-second intervals. The goal of the present study was to use the flyover noise data to deduce acoustical reflection coefficients and hence, acoustical impedances.

Chapkis, R. L.↗

Future data processing and its effect on spaceborne sensors

Remotely sensed data are attaining a new stature. New model for their use are being developed. Data delays are being overcome, and consideration is being given to multiple satellites and platforms providing shorter-interval repeat coverage. Statewide data systems are being developed to take advantage of remotely sensed data as a new analysis tool.

Billingsley, F. C.↗

Sensitivity of SLR baselines to errors in Earth orientation

The sensitivity of inter station distances derived from Satellite Laser Ranging (SLR) to errors in Earth orientation is discussed. An analysis experiment is performed which imposes a known polar motion error on all of the arcs used over this interval. The effect of the averaging of the errors over the tracking periods of individual sites is assessed. Baselines between stations that are supported by a global network of tracking stations are only marginally affected by errors in Earth orientation. The global network of stations retains its integrity even in the presence of systematic changes in the coordinate frame. The effect of these coordinate frame changes on the relative locations of the stations is minimal.

Smith, D. E.↗

A Monte Carlo study of Weibull reliability analysis for space shuttle main engine components

The incorporation of a number of additional capabilities into an existing Weibull analysis computer program and the results of Monte Carlo computer simulation study to evaluate the usefulness of the Weibull methods using samples with a very small number of failures and extensive censoring are discussed. Since the censoring mechanism inherent in the Space Shuttle Main Engine (SSME) data is hard to analyze, it was decided to use a random censoring model, generating censoring times from a uniform probability distribution. Some of the statistical techniques and computer programs that are used in the SSME Weibull analysis are described. The methods documented in were supplemented by adding computer calculations of approximate (using iteractive methods) confidence intervals for several parameters of interest. These calculations are based on a likelihood ratio statistic which is asymptotically a chisquared statistic with one degree of freedom. The assumptions built into the computer simulations are described. The simulation program and the techniques used in it are described there also. Simulation results are tabulated for various combinations of Weibull shape parameters and the numbers of failures in the samples.

Abernethy, K.↗

Evidence of atmospheric gravity wave perturbations of the Brunt-Vaisala frequency in the atmosphere

A series of high altitude, medium resolution, measurements of temperature, pressure and turbulence have been performed by the Air Force Geophysics Laboratory. These measurements were conducted using the VIZ Manufacturing Co. microsondes with attached micro-thermal probes measuring the temperature structure coefficient. A typical atmospheric temperature measurement is given. Several small temperature inversions are evident in the troposphere. The stratosphere is marked with numerous fluctuations in the temperature profile. Microsondes provide temperature and pressure measurements every 4 seconds up to a maximum altitude of 30 km (MSL). Since the average ascent rate is 5 m/s, the altitude interval between the measurement reports is 20 m. The potential temperature is calculated from the temperature and pressure. Spectral analysis of atmospheric Brunt-Vaisala frequencies reveal spectra similiar to the velocity spectra of Dewan et al. (1984), Daniels (1982), and Endlich and Singleton (1969). The Brunt-Vaisala spectra indicate the existence of separate, distinguishable wave modes.

Good, R. E.↗

Magnetic field draping in the Comet Halley coma - Comparison of Vega observations with computer simulations

During the Vega-1 encounter with Comet Halley, the magnetometer observed draping and compression of the interplanetary magnetic field. These are reproduced well by a three-dimensional MHD simulation of the cometary interaction. Rotations in the magnetic field similar to those at closest approach are also observed 2.75 hours earlier. It is suggested that both rotations correspond to the same IMF interval and that the spacecraft had overtaken the plasma and encountered 'older' magnetic field as it penetrated the coma. Analysis of the MHD model indicates that it should take about 3 to 5 hours for a solar wind parcel to pass from the unperturbed solar wind to Vega-1 at closest approach. A simulated magnetic field profile composed of nested sections for different IMF orientations closely resembles the observations. This result supports the hypothesis of layered magnetic orientations in the coma.

Schwingenschuh, K.↗

Surface composition of solid-rocket exhausted aluminum oxide particles

Particulate samples of aluminum oxide were collected on Teflon filters from the exhaust plume of the Space Shuttle (STS-61A, October 30, 1985) over the altitude interval 4.6-7.6 km immediately after launch. These particles were analyzed using SEM, energy-dispersive X-ray analysis, electron spectroscopy for chemical analysis, X-ray fluorescent spectroscopy, and conventional wet-chemical techniques. The samples were 0.6-1.0 percent surface-chlorided (chlorided meaning predominantly aluminum chlorides and oxychlorides, possibly including other adsorbed forms of chloride) by weight. This level of chloriding is about one-third of the amount determined previously from laboratory-prepared alumina and surface site samples of solid-rocket-produced alumina (SRPA) after both had been exposed to moist HCl vapor at temperatures down to ambient. This level is equivalent to previous laboratory results with samples exposed to moist HCl at temperatures above the boiling point of water. It is suggested that the present lower chloriding levels, determined for samples from a 'dry' Shuttle exhaust cloud, underscore the importance of a liquid water/hydrochloric acid phase in governing the extent of surface chloriding of SRPA. The reduced chloriding is not trivial with respect to potential physical/chemical modification of the SRPA particle surfaces and their corresponding interaction with the atmosphere.

Cofer, Wesley R., III↗

Analysis of the effects of mean local node-crossing time on the evolution of Sun-synchronous orbits

An investigation of the effect of mean local node-crossing time on the evolution of Sun-synchronous orbits was undertaken during Phase-A orbit analysis for the National Oceanic and Atmospheric Administration (NOAA) O,P,Q environmental spacecraft. That analysis added to the growing body of evidence that individual Sun-synchronous missions, at differing node-crossing times, experience nodal drift rates that can differ in both magnitude and direction. A Sun-synchronous orbit is obtained by means of a nodal drift rate approximating the 0.9856-degree-per-day apparent precession of the position of the mean Sun. This drift rate is achieved through the interaction of the orbital semimajor axis and inclination in Earth's geopotential field. Influencing perturbations include atmospheric drag and, most important, the effects of solar gravitation on inclination. The present analysis examines a series of Sun-synchronous orbits with mean local node-crossing times at 1-hour intervals from 6 a.m. to 6 p.m. It considers the fixed geometry of each orbital plane with respect to both the Sun and the diurnal atmospheric bulge, then analyzes the influence of these features upon the evolution of the semimajor axix and inclination and thus upon the rate of the nodal drift in the course of 1 year.

Jordan, P.↗

Analysis of atmospheric trace constituents from high resolution infrared balloon-borne and ground-based solar absorption spectra

Results of ongoing studies of high-resolution solar absorption spectra aimed at the identification and quantification of trace constituents of importance in the chemistry of the stratosphere and upper troposphere are presented. An analysis of balloon-borne and ground-based spectra obtained at 0.0025/cm covering the 700-2200/cm interval is presented. The 0.0025/cm spectra, along with corresponding laboratory spectra, improves the spectral line parameters, and thus the accuracy of quantifying trace constituents. Results for COF2, F22, SF6, and other species are presented. The retrieval methods used for total column density and altitude distribution for both ground-based and balloon-borne spectra are also discussed.

Goldman, A.↗

Assessment of autonomic response by broad-band respiration

We present a technique for introducing broad-band respiratory perturbations so that the response characteristics of the autonomic nervous system can be determined noninvasively over a wide range of physiologically relevant frequencies. A subject's respiratory bandwidth was broadened by breathing on cue to a sequence of audible tones spaced by Poisson intervals. The transfer function between the respiratory input and the resulting instantaneous heart rate was then computed using spectral analysis techniques. Results using this method are comparable to those found using traditional techniques, but are obtained with an economy of data collection.

NASA Discipline Cardiopulmonary↗

Non-Parametric Collision Probability for Low-Velocity Encounters

An implicit, but not necessarily obvious, assumption in all of the current techniques for assessing satellite collision probability is that the relative position uncertainty is perfectly correlated in time. If there is any mis-modeling of the dynamics in the propagation of the relative position error covariance matrix, time-wise de-correlation of the uncertainty will increase the probability of collision over a given time interval. The paper gives some examples that illustrate this point. This paper argues that, for the present, Monte Carlo analysis is the best available tool for handling low-velocity encounters, and suggests some techniques for addressing the issues just described. One proposal is for the use of a non-parametric technique that is widely used in actuarial and medical studies. The other suggestion is that accurate process noise models be used in the Monte Carlo trials to which the non-parametric estimate is applied. A further contribution of this paper is a description of how the time-wise decorrelation of uncertainty increases the probability of collision.

Carpenter, J. Russell↗

Evaluation of Operational Procedures for Using a Time-Based Airborne Inter-arrival Spacing Tool

An airborne tool has been developed based on the concept of an aircraft maintaining a time-based spacing interval from the preceding aircraft. The Advanced Terminal Area Approach Spacing (ATAAS) tool uses Automatic Dependent Surveillance-Broadcast (ADS-B) aircraft state data to compute a speed command for the ATAAS-equipped aircraft to obtain a required time interval behind another aircraft. The tool and candidate operational procedures were tested in a high-fidelity, full mission simulator with active airline subject pilots flying an arrival scenario using three different modes for speed control. The objectives of this study were to validate the results of a prior Monte Carlo analysis of the ATAAS algorithm and to evaluate the concept from the standpoint of pilot acceptability and workload. Results showed that the aircraft was able to consistently achieve the target spacing interval within one second (the equivalent of approximately 220 ft at a final approach speed of 130 kt) when the ATAAS speed guidance was autothrottle-coupled, and a slightly greater (4-5 seconds), but consistent interval with the pilot-controlled speed modes. The subject pilots generally rated the workload level with the ATAAS procedure as similar to that with standard procedures, and also rated most aspects of the procedure high in terms of acceptability. Although pilots indicated that the head-down time was higher with ATAAS, the acceptability of head-down time was rated high. Oculometer data indicated slight changes in instrument scan patterns, but no significant change in the amount of time spent looking out the window between the ATAAS procedure versus standard procedures.

Oseguera-Lohr, Rosa M.↗

Ice Surface Elevation Changes in East Antarctica from Satellite Altimetry

Estimates of the overall mass balance and seasonal and inter-annual variations in the surface mass balance are obtainable from time-series of ice surface elevations measured by satellite altimetry. Beginning in 2001, NASA's ICESat laser altimeter and lidar mission will significantly improve the range accuracy, the orbit accuracy, and the spatial coverage for measurement of ice sheet elevations (to 86 S) , as compared to previous radar altimeters designed for ocean measurements The radar altimeters on Seasat and Geosat provided ice sheet measurements to 72 S, and on ERS-1 and ERS-2 to 81 S. Although radar altimetry has significant limitations in coverage (due to loss of tracking) and accuracy over sloping surfaces, information on ice-sheet surface-elevation changes has been derived for parts of Antarctica. Recently, the accuracy of the ice measurements by Seasat (3 months of 1978) and Geosat (1985 to 1989) have been improved by new calculations of the satellite orbit heights and other altimeter corrections. Residual orbit errors and inter-satellite biases are evaluated by crossover analysis and by global adjustments to an ocean surface derived from altimeter data. The standard deviation of the orbit error is less than 9 cm, and the long-term trend in the error appears to be less than 1 cm/yr. Orbit errors can be further reduced by adjustment to the ocean surface, but false signals of several cm/yr may be also introduced by the adjustments. These false signals are caused mainly by residual errors in the altimeter corrections over the ocean, and secondary by real changes in the ocean surface elevation. Maps of ice sheet elevation changes north of 72 S are derived from Seasat-Geosat crossovers and from 4.5 years of Geosat crossovers. A notable ice thinning rate of about 50 cm/yr is found at elevations below 2200 meters between 70 and 72 S to the East of the Amery ice shelf, in both the Seasat-Geosat and Geosat-Geosat time intervals Above 2200 meters, to the ridge around 95 E, the thinning is about 10 to 20 cm/yr. For the Seasat/Geosat interval, a thickening is noted on the area East of the ridge between about 95 E and 115 E. Preliminary results from analysis of ERS-1 and ERS-2 radar altimeter data are also described.

Zwally, H. Jay↗