Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “intercalation material”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Dual‐Ion Intercalation and High Volumetric Capacitance in a Two‐Dimensional Non‐Porous Coordination Polymer

Abstract Intercalation is a promising ion‐sorption mechanism for enhancing the energy density of electrochemical capacitors (ECs) because it offers enhanced access to the electrochemical surface area. It requires a rapid transport of ions in and out of a host material, and it must occur without phase transformations. Materials that fulfil these requirements are rare; those that do intercalate almost exclusively cations. Herein, we show that Ni 3 (benzenehexathiol) (Ni 3 BHT), a non‐porous two‐dimensional (2D) layered coordination polymer (CP), intercalates both cations and anions with a variety of charges. Whereas cation intercalation is pseudocapacitive, anions intercalate in a purely capacitive fashion. The excellent EC performance of Ni 3 BHT provides a general basis for investigating similar dual‐ion intercalation mechanisms in the large family of non‐porous 2D CPs.

Banda, Harish↗

High-rate, high-capacity electrochemical energy storage in hydrogen-bonded fused aromatics

Designing materials for electrochemical energy storage with short charging times and high charge capacities is a longstanding challenge. The fundamental difficulty lies in incorporating a high density of redox couples into a stable material that can efficiently conduct both ions and electrons. We report all-organic, fused aromatic materials that store up to 310 mAh g –1 and charge in as little as 33 s. This performance stems from abundant quinone/imine functionalities that decorate an extended aromatic backbone, act as redox-active sites, engage in hydrogen bonding, and enable a delocalized high-rate energy storage with stability upon cycling. Here, the extended conjugation and hydrogen-bonding-assisted bulk charge storage contrast with the surface-confined or hydration-dependent behavior of traditional inorganic electrodes.

36 MATERIALS SCIENCE↗

Structural characterization and thermal properties of polyamide 6.6/Mg, Al/adipate-LDH nanocomposites obtained by solid state polymerization

A new nanocomposite was obtained by dispersing an adipate-modified layered double hydroxide (Ad-LDH) with adipic acid and hexamethylene diamine. These samples were polymerized in the solid phase under a nitrogen flow for 200 min at 190 {sup o}C. The structural and compositional details of the nanocomposite were determined by powder X-ray diffraction (PXRD), fourier transform infrared (FTIR) spectroscopy, focused ion beam (FIB), thermogravimetric analysis (TGA) and differential thermal analysis (DTA). The PXRD patterns and FIB images show a partially intercalated and partially exfoliated dispersion of layered crystalline materials in the polyamide 6.6 matrix. The best dispersion level is achieved in polyamide 6.6/LDH nanocomposites with low LDH loading. Some residual tactoids and particle agglomerates are also evident at high concentration. The best thermal stability of the nanocomposites is shown by the sample with 0.1% LDH content, for which it is higher than that of pure polyamide. - Graphical abstract: A new nanocomposite was obtained by compounding an adipate-modified layered double hydroxides (LDH) with adipic acid and hexamethylene diamine. These samples were polymerized in the solid phase under a nitrogen flow for 200 min at 190 {sup o}C. The nanodispersion of LDH in polyamide 6.6 may be qualitatively estimated from the analysis and PXRD patterns and FIB images. The decomposition temperature in the nanocomposite with 0.1 % LDH increases significantly compared to that for pristine PA6.6. .

36 MATERIALS SCIENCE↗

Protecting groups in insertion chemistry: Site-selective positioning of lithium ions in intercalation hosts

The expanding toolbox of functionalization chemistries for selectively installing moieties on specific sites of a substrate underpins almost all modern organic and biochemical syntheses. Likewise, the installation of mobile guest ions in specific interstitial sites and their transport along specific diffusion pathways forms the basis of modern lithium (Li)-ion battery electrodes. Many insertion hosts afford a diverse range of accessible interstitial sites. However, site-selective positioning of cations with atomic precision remains almost entirely unexplored. Here, we show that by deciphering site preferences of co/pre-intercalated cations, we can position Li ions in four distinct sites within a 1D ζ-V 2 O 5 insertion host. The use of topochemistry to effect single-crystal-to-single-crystal transformations enables atomic-resolution mapping of the selective positioning of Li ions through single-crystal X-ray diffraction. Here we image interstitial sites that are occupied at high depths of discharge, thereby obtaining unprecedented structural insight into “fully stuffed” frameworks critical for the realization of high-energy-density intercalation electrodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Unravelling the impact of reaction paths on mechanical degradation of intercalation cathodes for lithium-ion batteries

The intercalation compounds are generally considered as ideal electrode materials for lithium-ion batteries thanks to their minimum volume expansion and fast lithium ion diffusion. However, cracking still occurs in those compounds and has been identified as one of the critical issues responsible for their capacity decay and short cycle life, although the diffusion-induced stress and volume expansion are much smaller than those in alloying-type electrodes. Here, we designed a thin-film model system that enables us to tailor the cation ordering in LiNi 0.5 Mn 1.5 O 4 spinels and correlate the stress patterns, phase evolution, and cycle performances. Surprisingly, we found that distinct reaction paths cause negligible difference in the overall stress patterns but significantly different cracking behaviors and cycling performances: 95% capacity retention for disordered LiNi 0.5 Mn 1.5 O 4 and 48% capacity retention for ordered LiNi 0.5 Mn 1.5 O 4 after 2000 cycles. We were able to pinpoint that the extended solid-solution region with suppressed phase transformation attributed to the superior electrochemical performance of disordered spinel. Furthermore, this work envisions a strategy for rationally designing stable cathodes for lithium-ion batteries through engineering the atomic structure that extends the solid-solution region and suppresses phase transformation.

25 ENERGY STORAGE↗

Electrochemically induced amorphous-to-rock-salt phase transformation in niobium oxide electrode for Li-ion batteries

Intercalation-type metal oxides are promising negative electrode materials for safe rechargeable lithium-ion batteries due to the reduced risk of Li plating at low voltages. Nevertheless, their lower energy and power density along with cycling instability remain bottlenecks for their implementation, especially for fast-charging applications. Here, we report a nanostructured rock-salt Nb 2 O 5 electrode formed through an amorphous-to-crystalline transformation during repeated electrochemical cycling with Li + . This electrode can reversibly cycle three lithiums per Nb 2 O 5 , corresponding to a capacity of 269 mAh g –1 at 20 mA g –1 , and retains a capacity of 191 mAh g –1 at a high rate of 1 A g –1 . Further, it exhibits superb cycling stability with a capacity of 225 mAh g –1 at 200 mA g –1 for 400 cycles, and a Coulombic efficiency of 99.93%. We attribute the enhanced performance to the cubic rock-salt framework, which promotes low-energy migration paths. Our work suggests that inducing crystallization of amorphous nanomaterials through electrochemical cycling is a promising avenue for creating unconventional high-performance metal oxide electrode materials.

25 ENERGY STORAGE↗

Influence of lithium vacancies on the polaronic transport in olivine phosphate structure

Intercalation and deintercalation of lithium ions in cathode materials are of principal to the operation of current rechargeable lithium ion batteries. The performance of lithium ion batteries highly relies on the active cathode material which includes cell potential, power/energy density, capacity, etc. An important issue in this class of material is to resolve the factors governing the electron and ion transport in olivine phosphate structure. In this class of material, there is still an open debate on the mechanism of charge transport including both polarons and lithium ions. On the one hand, this is due to the large disparity between the experimental results and the theoretical model predictions. On the other hand, this is also due to the lack of precise experimental measurement without any parasitic phases in a given cathode material. Here, we present the polaronic conduction in lithiated triphylite LiFePO{sub 4} (LFP) and delithiated heterosite FePO{sub 4} (FP) by means of broadband ac impedance spectroscopy over wide range temperatures and frequency. It is found that the LFP phase possess two orders of higher polaronic conductivity than FP phase despite having similar mobility of polarons in both phases. We show that the differences in the polaronic conductivity of two phases are due to the significant differences in concentration of polarons. It is found that the formation energy of polarons in individual phases is mainly determined by the corresponding defect state associated with it. The temperature dependent dc conductivity has been analyzed within the framework of Mott model of polaronic conduction and explored the origin of polaronic conduction mechanism in this class of material.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Lithium ion intercalation in thin crystals of hexagonal TaSe 2 gated by a polymer electrolyte

Ionic liquid gating has been used to modify the properties of layered transition metal dichalcogenides (TMDCs), including two-dimensional (2D) crystals of TMDCs used extensively recently in the device work, which has led to observations of properties not seen in the bulk. The main effect comes from the electrostatic gating due to the strong electric field at the interface. In addition, ionic liquid gating also leads to ion intercalation when the ion size of the gate electrolyte is small compared to the interlayer spacing of TMDCs. However, the microscopic processes of ion intercalation have rarely been explored in layered TMDCs. Here, we employed a technique combining photolithography device fabrication and electrical transport measurements on the thin crystals of hexagonal TaSe2 using multiple channel devices gated by a polymer electrolyte LiClO 4 /Polyethylene oxide (PEO). The gate voltage and time dependent source-drain resistances of these thin crystals were used to obtain information on the intercalation process, the effect of ion intercalation, and the correlation between the ion occupation of allowed interstitial sites and the device characteristics. We found a gate voltage controlled modulation of the charge density waves and a scattering rate of charge carriers. Furthermore our work suggests that ion intercalation can be a useful tool for layered materials engineering and 2D crystal device design.

36 MATERIALS SCIENCE↗

In situ oligomerization of 2-(thiophen-3-yl)acetate intercalated into Zn{sub 2}Al layered double hydroxide

A layered double hydroxide (LDH) with cation composition Zn{sub 2}Al was intercalated with 2-(thiophen-3-yl)acetate (3-TA) monomers. To achieve in situ polymerization and/or oligomerization of the intercalated monomers, soft thermal treatments were carried out, and subsequent hybrid LDH materials were analyzed by means of several characterization techniques using powder X-ray diffraction (PXRD), Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), {sup 13}C CP–MAS nuclear magnetic resonance (NMR), electron spin resonance (EPR), scanning electron microscopy (SEM), and transmission electron microscopy (TEM), inductively coupled plasma optical emission spectroscopy (ICP–OES), and elemental analysis. PXRD analysis suggested that the intercalated monomers formed a bilayer. Thermal treatment of the hybrid LDH assembly above 120 °C provokes partially the breakdown of the layered structure, generating the phase zincite. EPR results indicated that vicinal monomers (oligomerization) were bound to each other after hydrothermal or thermal treatment, leading to a polaron response characteristic of electron conductivity localized on a restricted number of thiophene-based monomer segments. Localized unpaired electrons exist in the material and interact with the {sup 27}Al nuclei of the LDH layers by superhyperfine coupling. These unpaired electrons also interact with the surface of ZnO (O{sup 2−} vacancies), formed during the thermal treatments. - Graphical abstract: We synthesized a layered double hydroxide (LDH) with cation composition Zn{sub 2}Al, intercalated with 2-(thiophen-3-yl)acetate (3-TA) monomers, by coprecipitation at constant pH. We thermally treated the material, to achieve in situ polymerization and/or oligomerization of the intercalated monomers. - Highlights: • A Zn{sub 2}Al–LDH was intercalated with 2-(thiophen-3-yl)acetate monomers. • To achieve in situ oligomerization of the monomers, thermal treatments were made. • Thermal treatment above 120 °C causes partially breakdown of the LDH structure. • ESR results indicated a polaron response characteristic of electron conductivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Strain-retardant coherent perovskite phase stabilized Ni-rich cathode

The use of state-of-the-art Ni-rich layered oxides (LiNi x Co y Mn 1-x-y O 2 , x > 0.5) as the cathode material for lithium-ion batteries can push the energy and power density to a higher level than is currently available. However, volume variation associated with anisotropic lattice strain and stress that is being developed during lithium (de) intercalation induces severe structural instability and electrochemical decay of the cathode materials, which is amplified further when the battery is operating at a high voltage (above 4.5 V), which is essential for unlocking its high energy. Even after much effort by the research community, an intrinsic strain-retardant method for directly alleviating the continuous accumulation of lattice strain remains elusive. By introducing a coherent perovskite phase into the layered structure functioning as a ‘rivet’, we significantly mitigate the pernicious structural evolutions by a pinning effect. The lattice strain evolution in every single cycle is markedly reduced by nearly 70% when compared with conventional materials, which significantly enhances morphological integrity leading to a notable improvement in battery cyclability. This strain-retardant approach broadens the perspective for lattice engineering to release the strain raised from lithium (de)intercalation and paves the way for the development of high-energy-density cathodes with long durability.

25 ENERGY STORAGE↗

Direct Investigation of Mg Intercalation into the Orthorhombic V 2 O 5 Cathode Using Atomic-Resolution Transmission Electron Microscopy [Direct Investigation of Mg intercalation into orthorhombic V 2 O 5 cathode using Atomic Resolution Electron Microscopy Methods]

Batteries based on Mg metal anode can promise much higher specific volumetric capacity and energy density compared to Li-ion systems and are, at the same time, safer and more cost-effective. While previous experimental reports have claimed reversible Mg intercalation into beyond Chevrel phase cathodes, they provide limited evidence of true Mg intercalation other than electrochemical data. Transmission electron microscopy techniques provide unique capabilities to directly image Mg intercalation and quantify the redox reaction within the cathode material. Here, we present a systematic study of Mg insertion into orthorhombic V 2 O 5 , combining aberration-corrected scanning transmission electron microscopy (STEM) imaging, electron energy-loss spectroscopy (EELS), and energy-dispersive X-ray spectroscopy (EDX) analysis. We compare the results from an electrochemically cycled V 2 O 5 cathode in a prospective full cell with Mg metal anode with a chemically synthesized MgV 2 O 5 sample. Results suggest that the electrochemically cycled orthorhombic V 2 O 5 cathode shows a local formation of the theoretically predicted ϵ-Mg 0.5 V 2 O 5 phase; however, the intercalation levels of Mg are lower than predicted. Lastly, this phase is different from the chemically synthesized sample, which is found to represent the δ-MgV 2 O 5 phase.

36 MATERIALS SCIENCE↗

Vibrational Properties of Pristine and Lithium-Intercalated Black Phosphorous under High-Pressure

Structural evolution of Li-intercalated and pristine black phosphorous (BP) under high-pressure (up to ≈8 GPa) is studied using in situ Raman spectroscopy. Even though both materials show a monotonic blueshift of the out-of-plane vibrational mode (A 1 g ) with pressure, Li-intercalated BP do not show a blueshift until a threshold pressure (2.4 GPa) is reached to compensate the structural expansion caused by intercalation. However, the in-plane modes (B 2g and A 2 g) in each sample respond differently. In the mid-pressure region, they both show redshifts which in Li-intercalated BP is also followed by abrupt blueshifts. Such behavior indicates pressure-induced structural reorganizations inside the material. Computational modeling reveals the existence of a process of P-P bond breaking and reforming in the system due to the redistribution of intercalated Li atoms under pressure. This work shows the significance of combined effect of pressure and intercalation on structural changes in the search for new phases of BP and other two-dimensional (2D) materials.

36 MATERIALS SCIENCE↗

Investigation of mechanochemical interactions of hydrogen with earth materials in a subsurface gas storage

The goal of this project is to investigate the molecular interactions of H 2 with earth materials (EMs) that may potentially affect economics and safety of H 2 geological storage (HGS). We investigated (1) the H 2 intercalation into interlayers of phyllosilicates, (2) the competitive adsorption of H 2 /CH 4 onto porous materials, and (3) solubility of H 2 in interfacial and confined hydrocarbons. Our results indicate that (i) H 2 intercalation into hydrated interlayers is thermodynamically unfavorable and H 2 solubility in hydrated clay interlayers is in the same order of magnitude as that in bulk water, (ii) CH 4 outcompetes H 2 in adsorption onto kerogen, due to stronger CH 4 -kerogen interactions than H 2 -kerogen interactions, (iii) H 2 tends to dissolve more in oil than in water, and the introduction of CO 2 as a cushion gas reduces H 2 partitioning near the kaolinite surfaces. The outcomes provide foundational knowledge for preparing the USA for future storage site selection and storage system design, supporting DOE missions in clean and secured energy.

08 HYDROGEN↗

Achieving environmental stability in an atomically thin quantum spin Hall insulator via graphene intercalation

Atomic monolayers on semiconductor surfaces represent an emerging class of functional quantum materials in the two-dimensional limit — ranging from superconductors and Mott insulators to ferroelectrics and quantum spin Hall insulators. Indenene, a triangular monolayer of indium with a gap of ~ 120 meV is a quantum spin Hall insulator whose micron-scale epitaxial growth on SiC(0001) makes it technologically relevant. However, its suitability for room-temperature spintronics is challenged by the instability of its topological character in air. It is imperative to develop a strategy to protect the topological nature of indenene during ex situ processing and device fabrication. Here we show that intercalation of indenene into epitaxial graphene provides effective protection from the oxidising environment, while preserving an intact topological character. Our approach opens a rich realm of ex situ experimental opportunities, priming monolayer quantum spin Hall insulators for realistic device fabrication and access to topologically protected edge channels.

36 MATERIALS SCIENCE↗

Coverage-dependent structures and thermodynamic stability of intercalated Gd layers beneath buffer-layer graphene on SiC(0001)

Electronic properties of two-dimensional (2D) materials are strongly influenced by their atomic arrangements, making the theoretically-aided characterization of experimentally-synthesized 2D structures crucial. Using first-principles density functional theory, we analyze nearly 200 configurations of intercalated Gd layers beneath buffer-layer graphene on SiC(0001) over a Gd coverage range of 0.01 < θ < 1.2. By fully relaxing selectively-constructed configurations at each coverage within a large, low-strain supercell, we determine the coverage dependence of the chemical potential for intercalated Gd structures. Thermodynamically-preferred configurations below θ ≈ 0.8 form single-atom-thick monolayers, while 3D-like or multilayer structures emerge beyond θ ≈ 0.9. Most structures are amorphous-like, including the configuration at the chemical potential minimum around θ ≈ 0.4. In contrast, a strongly stretched Gd(0001)-like monolayer at θ = 1/3 and a nearly perfect Gd(0001) monolayer at θ = 1 are significantly less favorable with 0.16 eV and 0.82 eV higher chemical potentials above the minimum, respectively. Furthermore, the graphene layer decoupled by intercalated Gd near the chemical potential minimum is significantly flatter compared to its morphology above intercalated 3D structures at higher coverages and nearly isolated Gd atoms in the lowest coverage region. In conclusion, these findings align with our experimental results and underscore the need for further research on this unique intercalated system, which holds significant potential for diverse applications.

36 MATERIALS SCIENCE↗

Novel alkali intercalated and acid-exfoliated biochars with enhanced surface areas for contaminant adsorption applications

Cost-effective and eco-friendly adsorbents are essential in environmental engineering and biochar is a promising material from the perspective. A novel and efficient surface modification approach involving alkali intercalation and acid exfoliation was designed in this study to enhance the physicochemical properties of biochar. Here, the alkali intercalation process utilizes potassium hydroxide (KOH), while acid exfoliation involves varying HNO 3 , H 2 SO 4 , and H 3 PO 4 concentrations. A simple two-stage pyrolysis process was employed to facilitate the intercalation-exfoliation modification. The modified biochars were characterized using BET, SEM, XRD, etc., to understand physicochemical properties. To quantify the effectiveness of the modifications, adsorption of malachite green dye as a model moiety was investigated. Dye removal sorption rates exceeding 99 % were recorded in the case of the biochars modified through a two-step process using KOH and 0.1MH 3 PO 4 . Specifically, the highest contaminant removal of 99.9 % was recorded when 60 mg of the KOH-0.1MH 3 PO 4 biochar was employed, which is significantly higher than unmodified biochar’s 45.41 % removal at a higher dosage of 100 mg. Moreover, the adsorption kinetics revealed that all the modified biochars attained the maximum removal concentrations (~99 % removal) in a mere 300 min, indicating a tenfold improvement in adsorption rate from unmodified biochar's requirement of over 5000 min. The results achieved through this study provide a cost-effective, fast, and environment-friendly technology for enhancing the adsorption characteristics and performance of biochars toward contaminant removal.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Multimodal Analysis of Reaction Pathways of Cathode Materials for Lithium Ion Batteries

Conversion mechanism in lithium ion batteries provides higher capacity than intercalation mechanism since multiple numbers of electrons and lithium ions are associated. However, poor cycling stability, large voltage hysteresis, and low energy efficiency have been great challenges of conversion reaction. To address those issues, conversion-type electrode materials have been reformed via doping or substituting other elements. For example, iron fluorides (FeF 2 , FeF 3 ) have modified as iron oxyfluorides (FeF 1-x O x ), showing enhanced long-term stability. Furthermore, co-substituted (both anion and cation substituted) Fe 0.9 Co 0.1 OF (FeCoOF) was demonstrated excellent cycling stability. (capacity of 350 mAh g -1 at a current of 500 mA g -1 for 1000 cycles). Substituting anion and cation in iron fluoride has been suggested as an effective method to achieve better reversibility but understanding of lithiation reactions in co-substituted FeCoOF is not clear. This work takes advantage of ex-situ/ in-situ synchrotron X-ray based techniques and transmission electron microscopy to elucidate structural changes with lithium ion, which may provide fundamental insights into modifying conversion-type materials. Figure 1 presents discharge-charge curves and pair distribution function patterns acquired at each potential. As lithium ions were inserted, structural changes were noticed both at short-range and long-range. However, long-range ordering was nearly maintained even at 1 V, indicating absence of conversion reaction. Figure 2 shows lithiation induced structural evolution of a single FeCoOF nanorod observed in real time. As lithiation proceeds, the width of nanorods shows a stepwise increase, particularly A in figure 2d, which may indicate multiple steps of lithiation occur. Considering that conversion reaction takes place around 2 V in FeF 3 , co-substitution Co and O into iron fluoride may change thermodynamic features of lithiation reactions by lowering the initiation potential for conversion reaction. Instead, phase transformations occur at long-range order, which may help maintaining structural integrity during operation, eventually, achieving cycling stability.

25 ENERGY STORAGE↗