Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ice crystal icing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Effect of ice contamination of liquid-nitrogen drops in film boiling

Previously reported vaporization time data of liquid nitrogen drops in film boiling on a flat plate are about 30 percent shorter than predicted from standard laminar film boiling theory. This theory, however, had been found to successfully correlate the data for conventional fluids such as water, ethanol, benzene, or carbon tetrachloride. Experimental evidence that some of the discrepancy for cryogenic fluids results from ice contamination due to condensation is presented. The data indicate a fairly linear decrease in droplet evaporation time with the diameter of the ice crystal residue. After correcting the raw data for ice contamination along with convection, a comparison of theory with experiment shows good agreement.

Schoessow, G. J.↗
NASA NTRS1977

Effect of ice contamination on liquid-nitrogen drops in film boiling

Previously reported vaporization time data of liquid nitrogen drops in film boiling on a flat plate are about 30 percent shorter than predicted from standard laminar film boiling theory. This theory, however, had been found to successfully correlate the data for conventional fluids such as water, ethanol, benzene, or carbon tetrachloride. This paper presents experimental evidence that some of the discrepancy for cryogenic fluids results from ice contamination due to condensation. The data indicate a fairly linear decrease in droplet evaporation time with the diameter of the ice crystal residue. After correcting the raw data for ice contamination along with convection, a comparison of theory with experiment shows good agreement.

Schoessow, G. J.↗
NASA NTRS2017

A Dynamic Model for the Evaluation of Aircraft Engine Icing Detection and Control-Based Mitigation Strategies

Aircraft flying in regions of high ice crystal concentrations are susceptible to the buildup of ice within the compression system of their gas turbine engines. This ice buildup can restrict engine airflow and cause an uncommanded loss of thrust, also known as engine rollback, which poses a potential safety hazard. The aviation community is conducting research to understand this phenomena, and to identify avoidance and mitigation strategies to address the concern. To support this research, a dynamic turbofan engine model has been created to enable the development and evaluation of engine icing detection and control-based mitigation strategies. This model captures the dynamic engine response due to high ice water ingestion and the buildup of ice blockage in the engines low pressure compressor. It includes a fuel control system allowing engine closed-loop control effects during engine icing events to be emulated. The model also includes bleed air valve and horsepower extraction actuators that, when modulated, change overall engine operating performance. This system-level model has been developed and compared against test data acquired from an aircraft turbofan engine undergoing engine icing studies in an altitude test facility and also against outputs from the manufacturers customer deck. This paper will describe the model and show results of its dynamic response under open-loop and closed-loop control operating scenarios in the presence of ice blockage buildup compared against engine test cell data. Planned follow-on use of the model for the development and evaluation of icing detection and control-based mitigation strategies will also be discussed. The intent is to combine the model and control mitigation logic with an engine icing risk calculation tool capable of predicting the risk of engine icing based on current operating conditions. Upon detection of an operating region of risk for engine icing events, the control mitigation logic will seek to change the engines operating point to a region of lower risk through the modulation of available control actuators while maintaining the desired engine thrust output. Follow-on work will assess the feasibility and effectiveness of such control-based mitigation strategies.

engine control↗
NASA NTRS2017

A Dynamic Model for the Evaluation of Aircraft Engine Icing Detection and Control-Based Mitigation Strategies

Aircraft flying in regions of high ice crystal concentrations are susceptible to the buildup of ice within the compression system of their gas turbine engines. This ice buildup can restrict engine airflow and cause an uncommanded loss of thrust, also known as engine rollback, which poses a potential safety hazard. The aviation community is conducting research to understand this phenomena, and to identify avoidance and mitigation strategies to address the concern. To support this research, a dynamic turbofan engine model has been created to enable the development and evaluation of engine icing detection and control-based mitigation strategies. This model captures the dynamic engine response due to high ice water ingestion and the buildup of ice blockage in the engines low pressure compressor. It includes a fuel control system allowing engine closed-loop control effects during engine icing events to be emulated. The model also includes bleed air valve and horsepower extraction actuators that, when modulated, change overall engine operating performance. This system-level model has been developed and compared against test data acquired from an aircraft turbofan engine undergoing engine icing studies in an altitude test facility and also against outputs from the manufacturers customer deck. This paper will describe the model and show results of its dynamic response under open-loop and closed-loop control operating scenarios in the presence of ice blockage buildup compared against engine test cell data. Planned follow-on use of the model for the development and evaluation of icing detection and control-based mitigation strategies will also be discussed. The intent is to combine the model and control mitigation logic with an engine icing risk calculation tool capable of predicting the risk of engine icing based on current operating conditions. Upon detection of an operating region of risk for engine icing events, the control mitigation logic will seek to change the engines operating point to a region of lower risk through the modulation of available control actuators while maintaining the desired engine thrust output. Follow-on work will assess the feasibility and effectiveness of such control-based mitigation strategies.

engine control↗
NASA NTRS2022

Highly Supercooled Riming and Unusual Triple-Frequency Radar Signatures Over McMurdo Station, Antarctica

Riming of ice crystals by supercooled water droplets is an efficient ice growth process, but its basic properties are still poorly known. While it has been shown to contribute significantly to surface precipitation at mid-latitudes, little is known about its occurrence at high latitudes. In Antarctica, two competing effects can influence the occurrence of riming: (i) the scarcity of supercooled liquid water clouds due to the extremely low tropospheric temperatures and (ii) the low aerosol concentration, which may lead to the formation of fewer and larger supercooled drops potentially resulting in an enhanced riming efficiency. In this work, by exploiting the deployment of an unprecedented number of multiwavelength remote sensing systems (including triple-frequency radar measurements) in West Antarctica, during the Atmospheric Radiation Measurements West Antarctic Radiation Experiment (AWARE) field campaign, we evaluate the riming incidence at McMurdo Station and find that riming occurs at much lower temperatures when compared to previous results in the mid-latitudes. This suggests the possible occurrence of a common atmospheric state over Antarctica that includes a rather stable atmosphere inhibiting turbulent mixing, and a high riming efficiency driven by large cloud droplets. We then focus on a peculiar case study featuring a persistent layer with a particularly pronounced riming signature in triple-frequency radar data but only a relatively modest amount of supercooled liquid water. In-depth analysis of the radar observations suggests that such signatures can only be explained by the combined effects of moderately rimed aggregates or similarly shaped florid polycrystals and a narrow particle size distribution (PSD). Simulations of this case study performed with a one-dimensional bin model indicate that similar triple-frequency radar observations can be reproduced when narrow PSDs are simulated. Such narrow PSDs can in turn be explained by two key factors: (i) the presence of a shallow homogeneous droplet or humidified aerosol freezing layer aloft seeding an underlying supercooled liquid layer, and (ii) the absence of turbulent mixing throughout a stable polar atmosphere that sustains narrow PSDs, as hydrometeors grow from the nucleation region aloft to ice particles of several millimeters in size, by vapor deposition and then riming.

Riming↗
NASA NTRS1988

Possible significance of cubic water-ice, H2O-Ic, in the atmospheric water cycle of Mars

The possible formation and potential significance of the cubic ice polymorph on Mars is discussed. When water-ice crystallizes on Earth, the ambient conditions of temperature and pressure result in the formation of the hexagonal ice polymorph; however, on Mars, the much lower termperature and pressures may permit the crystallization of the cubic polymorph. Cubic ice has two properties of possible importance on Mars: it is an excellant nucleator of other volatiles (such as CO2), and it undergoes an exothermic transition to hexagonal ice at temperatures above 170 K. These properties may have significant implications for both martian cloud formation and the development of the seasonal polar caps.

Gooding, James L.↗
DOE OSTI2024

Ice-slurry production for solar-ice systems using supercooling with an in-stream crystallizer

Using ice slurry produced from supercooled water with an in-stream crystallizer opens a new path for solarice systems, increasing efficiency and reducing investment cost compared to ice-on-coil systems. Power needs are decoupled from the stored energy since the heat exchangers are not evenly distributed in the ice storage vessel but directly placed as the heat pump evaporator, which depends on the heat pump capacity and not on the ice storage volume. The novel ice storage design can serve as a heat source for a heat pump, where its evaporator is used to supercool water below 0 °C, or for refrigeration. The supercooled water at a temperature around −2 °C, maintained in a meta-stable liquid state, is triggered to nucleate in an in-stream crystallizer. The current design of the ice crystallizer allows for continuous operation of the system and scalability. Experimental results obtained with a gasketed plate heat exchanger used to supercool water and an in-stream crystallizer operated at a power of up to 6.5 kW are presented.

Thamm, Ann-Katrin↗
DOE OSTI2020

Toward Understanding the Simulated Phase Partitioning of Arctic Single-Layer Mixed-Phase Clouds in E3SM

21 Mixed-phase clouds are widespread in the Arctic and have substantial impacts on the 22 surface energy budget, sea ice extent, and regional climate. Significant changes are found in the 23 modeled phase partitioning of Arctic mixed-phase clouds in the newly developed U.S. 24 Department of Energy (DOE) Energy Exascale Earth System Model (E3SM) Atmosphere Model 25 version 1 (EAMv1) compared to its predecessor (CAM5/EAMv0). The mixed-phase clouds 26 simulated by EAMv1 is overly dominated by super-cool liquid which is often underestimated by 27 CAM5. Compared to CAM5, EAMv1 has made several important changes in its cloud physical 28 parameterizations, including using CLUBB to unify shallow convection, PBL turbulence, and 29 cloud macrophysics, as well as updating the MG two-moment cloud microphysics scheme and 30 using the CNT heterogeneous ice nucleation scheme to replace the Meyers scheme for mixed- 31 phase clouds. To understand which of the newly-implemented physical parameterizations is 32 responsible for the change of modeled mixed-phase cloud phase partitioning in EAMv1, 33 sensitivity tests are conducted by utilizing the short-term hindcast approach and results are 34 compared to the observations from the ARM Mixed-Phase Arctic Cloud Experiment (M-PACE) 35 field campaign. 36 It is found that although each scheme contributes to the decrease of cloud ice water 37 content (IWC) and increase of cloud liquid water content (LWC), only the combined effect of 38 CLUBB and CNT can explain the significant underestimation of IWC. By examining the budgets 39 of cloud microphysical processes, CLUBB is found to play a dominant role due to the fact that 40 CLUBB does not diagnoses cloud ice phase water in its assumed joint PDF method and thus may 41 not provide sufficient cloud ice to initialize ice phase microphysical processes such as the growth 42 of ice crystals through vapor deposition. Although a more effective heterogeneous ice nucleation 43 may alleviate the underestimation of IWC, the ice phase process in CLUBB requires urgent 44 attention in the future model development.

Zhang, Meng↗
DOE OSTI2025

Multi-seasonal measurements of the ground-level atmospheric ice-nucleating particle abundance on the North Slope of Alaska

Atmospheric ice-nucleating particles (INPs) are an important subset of aerosol particles that are responsible for the heterogeneous formation of ice crystals. INPs modulate the arctic cloud phase (liquid vs. ice), resulting in implications for radiative feedbacks. The number of arctic INP studies investigating specific INP episodes or sources increased recently. However, existing studies are based on short-duration field data, and long-term datasets are lacking. Continuous, long-term measurements are key to determining the abundance and variability of ambient arctic INPs and constraining aerosol–cloud interactions, e.g., to verify and/or improve simulations of mixed-phase clouds. Here, we present a new long-duration INP dataset from the Arctic: 2 years of predominantly immersion-mode INP concentrations (n INP ) measured continuously at the National Oceanic and Atmospheric Administration's Barrow Atmospheric Baseline Observatory (BRW) on the North Slope of Alaska. A portable ice nucleation experiment chamber (PINE-03), which simulates adiabatic expansion cooling, was used to directly measure the ground-level INP abundance with an approximately 12 min time resolution from October 2021 to December 2023. We document PINE-03 n INP measurements as well as estimated ice nucleation active surface site density (n s ) over a wide range of heterogeneous freezing temperatures from −16 to −31 °C from which we introduce new season-specific parameterizations suitable for modeling mixed-phase clouds. Collocated aerosol and meteorological data were analyzed to assess the correlation between ambient n INP , air mass origin region, and meteorological variability. Our findings suggest (1) very high freezing efficiency of INPs across the measured temperatures (n s ≈ 2×10 8 –10 10 m −2 for −16 to −31 °C), which is a factor of 10–1000 times greater efficiency as compared to that found in the previous mid-latitude INP measurements in fall using the same instrument; (2) surprisingly high n INP (≥ 1 L −1 at −25 °C) for the examined temperatures throughout the year that were not measured by PINE-03 at other sites; and (3) high n INP in spring, possibly related to arctic haze episodes. Relatively low concentrations of aerosol surface area and contrasting high-INP concentrations at BRW relative to mid-latitude sites are the possible reasons for the observed high freezing efficiency.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2004

Nucleation in Synoptically Forced Cirrostratus

Formation and evolution of cirrostratus in response to weak, uniform and constant synoptic forcing is simulated using a one-dimensional numerical model with explicit microphysics, in which the particle size distribution in each grid box is fully resolved. A series of tests of the model response to nucleation modes (homogeneous-freezing-only/heterogeneous nucleation) and heterogeneous nucleation parameters are performed. In the case studied here, nucleation is first activated in the prescribed moist layer. A continuous cloud-top nucleation zone with a depth depending on the vertical humidity gradient and one of the nucleation parameters is developed afterward. For the heterogeneous nucleation cases, intermittent nucleation zones in the mid-upper portion of the cloud form where the relative humidity is on the rise, because existent ice crystals do not uptake excess water vapor efficiently, and ice nuclei (IN) are available. Vertical resolution as fine as 1 m is required for realistic simulation of the homogeneous-freezing-only scenario, while the model resolution requirement is more relaxed in the cases where heterogeneous nucleation dominates. Bulk microphysical and optical properties are evaluated and compared. Ice particle number flux divergence, which is due to the vertical gradient of the gravity-induced particle sedimentation, is constantly and rapidly changing the local ice number concentration, even in the nucleation zone. When the depth of the nucleation zone is shallow, particle number concentration decreases rapidly as ice particles grow and sediment away from the nucleation zone. When the depth of the nucleation zone is large, a region of high ice number concentration can be sustained. The depth of nucleation zone is an important parameter to be considered in parametric treatments of ice cloud generation.

Lin, R.-F.↗
DOE OSTI2025

Contact Freezing of Water Droplets by Crystalline Organic Acids

The ability of water to freeze into ice crystals in mixed-phase clouds affects physical properties, including particle size, precipitation rates, and radiative properties. The presence of an insoluble particle at the surface of water droplets can promote ice nucleation at temperatures higher than that of pure water, even in the absence of a collision. However, contact freezing remains an underexplored mode of ice nucleation. Here, we present a study of atmospherically relevant organic acids and their role as effective ice-nucleating particles (INP) in contact mode using a Raman-microscope-equipped environmental chamber. We determined contact freezing temperatures induced by solid crystals of docosanol, adipic acid, cis-pinonic acid, fumaric acid, 4-hydroxybenzoic acid, palmitic acid, phthalic acid, sebacic acid, stearic acid, terephthalic acid, and vanillic acid. All solids except fumaric acid promoted contact freezing of water droplets at significantly higher temperatures than pure water in the chamber (−15.0 to −18.5 °C vs −21.3 °C). Physical and chemical properties were identified which correlate with greater effectiveness of INPs in the contact mode, including crystal lattice mismatch with ice, carbon number, and insolubility in water. In conclusion, we suggest that the presence of these organic solids in atmospheric aerosols may promote atmospheric ice nucleation at warm temperatures.

Clouds↗
NASA NTRS1993

Mesoscale simulations of the November 25-26 and December 5-6 cirrus cases using the RAMS model

The Regional Atmospheric Modeling System (RAMS), developed at Colorado State University, was used during the First ISCCP (International Satellite Cloud Climatology Project) Regional Experiment (FIRE) 2 (13 Nov. through 6 Dec. 1991) to provide real time forecasts of cirrus clouds. Forecasts were run once a day, initializing with the 0000 UTC dataset provided by NOAA (Forecast Systems Laboratory (FSL) Mesoscale Analysis and Prediction System (MAPS)). In order to obtain better agreement with observations, a second set of simulations were done for the FIRE 2 cases that occurred on 25-26 Nov. and 5-6 Dec. In this set of simulations, a more complex radiation scheme was used, the Chen/Cotton radiation scheme, along with the nucleation of ice occurring at ice supersaturations as opposed to nucleation occurring at water supersaturations that was done in the actual forecast version. The runs using these more complex schemes took longer wall clock time (7-9 hours for the actual forecasts as compared to 12-14 hrs for the runs using the more complex schemes) however, the final results of the simulations were definitely improved upon. Comparisons between these two sets of simulations are given. Now underway are simulations of these cases using a closed analytical solution for the auto-conversion of ice from a pristine ice class (sizes less than about 50 microns in effective diameter) to a snow class (effective diameters on the order of several hundred microns). This solution is employed along with a new scheme for the nucleation of ice crystals due to Meyers et al and Demott et al. The scheme is derived assuming complete gamma distributions for both the pristine and snow classes. The time rate of change of the number concentration and mass mixing-ratio of each distribution is found by calculating either the flux of crystals that grow beyond a certain critical diameter by vapor deposition in an ice supersaturated regime or by calculating the flux of crystals that evaporate to sizes below that same critical effective diameter.

Harrington, J. L.↗
DOE OSTI2019

Simulating a Mesoscale Convective System Using WRF with a New Spectral Bin Microphysics: Part 1: Hail vs Graupel

A modified Fast Spectral Bin Microphysics scheme (FSBM-2) embedded into the Weather Research and Forecasting Model (WRF) is used to simulate a mesoscale deep convective system observed during the Midlatitude Continental Convective Clouds Experiment (MC3E). FSBM-2 uses modified source codes as compared to the current FSBM (FSBM-1). In contrast to FSBM-1, FSBM-2 can simulate hail of several cm in diameter and includes additional processes such as spontaneous breakup of raindrops and aerosol regeneration by drop evaporation. It is shown that allowing large hail particles of diameters exceeding about 1 cm substantially increases the agreement between the simulated and observed squall-line structures both in the convective and stratiform regions. In contrast, if graupel particles are used to represent high-density hydrometeors in convective areas, the ratio of convective-to-stratiform areas diverges from the ratio seen in observations and maximum radar reflectivities are substantially underestimated. Analysis of snow size distributions in the stratiform area shows an important link between the ice crystals formed by homogeneous freezing in the convective area to ice particle number concentration in the stratiform region. Simulated raindrop size distributions in the stratiform area below the melting level from FSBM-2 show a good agreement with observations. The regeneration of CCN by droplet evaporation and detrainment of these CCN to the stratiform region increases the concentration of CCN there up to 8-9 km altitude; the additional CCN penetrate clouds and produce new droplets, leading to some convection intensification. Key words: Mesoscale convective systems (MCS), squall lines, spectral bin microphysics, large hail, in-cloud nucleation, size distributions of hydrometeors in MCS.

Shpund, Kobby↗
DOE OSTI2020

CERES MODIS Cloud Product Retrievals for Edition 4--Part I: Algorithm Changes

The Edition 2 (Ed2) cloud property retrieval algorithm system was upgraded and applied to the MODerate-resolution Imaging Spectroradiometer (MODIS) data for the Clouds and the Earth's Radiant Energy System (CERES) Edition 4 (Ed4) products. New calibrations for solar channels and the use of the 1.24-μm channel for cloud optical depth (COD) over snow improve the daytime consistency between Terra and Aqua MODIS retrievals. Use of additional spectral channels and revised logic enhanced the cloud-top phase retrieval accuracy. A new ice crystal reflectance model and a CO₂-channel algorithm retrieved higher ice clouds, while a new regional lapse rate technique produced more accurate water cloud heights than in Ed2. Ice cloud base heights are more accurate due to a new cloud thickness parameterization. Overall, CODs increased, especially over the polar (PO) regions. The mean particle sizes increased slightly for water clouds, but more so for ice clouds in the PO areas. New experimental parameters introduced in Ed4 are limited in utility, but will be revised for the next CERES edition. As part of the Ed4 retrieval evaluation, the average properties are compared with those from other algorithms and the differences between individual reference data and matched Ed4 retrievals are explored. Part II of this article provides a comprehensive, objective evaluation of selected parameters. More accurate interpretation of the CERES radiation measurements has resulted from the use of the Ed4 cloud properties.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1978

Airborne measurements of cloud forming nuclei and aerosol particles at Kennedy Space Center, Florida

Results of airborne measurements of the sizes and concentrations of aerosol particles, ice nuclei, and cloud condensation nuclei that were taken at Kennedy Space Center, Florida, are presented along with a detailed description of the instrumentation and measuring capabilities of the University of Washington airborne measuring facility (Douglas B-23). Airborne measurements made at Ft. Collins, Colorado, and Little Rock, Arkansas, during the ferry of the B-23 are presented. The particle concentrations differed significantly between the clean air over Ft. Collins and the hazy air over Little Rock and Kennedy Space Center. The concentrations of cloud condensation nuclei over Kennedy Space Center were typical of polluted eastern seaboard air. Three different instruments were used to measure ice nuclei: one used filters to collect the particles, and the others used optical and acoustical methods to detect ice crystals grown in portable cloud chambers. A comparison of the ice nucleus counts, which are in good agreement, is presented.

Radke, L. F.↗
NASA NTRS2021

Effect of volcanic emissions on clouds during the 2008 and 2018 Kilauea degassing events

Volcanic eruptions in otherwise clean environments are “natural experiments” wherein the effects of aerosol emissions on clouds and climate can be partitioned from meteorological variability and anthropogenic activities. In this work, we combined satellite retrievals, reanalysis products, and atmospheric modeling to analyze the mechanisms of aerosol–cloud interactions during two degassing events at the Kilauea volcano in 2008 and 2018. The eruptive nature of the 2008 and 2018 degassing events was distinct from long-term volcanic activity for Kilauea. Although previous studies assessed the modulation of cloud properties from the 2008 event, this is the first time such an analysis has been reported for the 2018 event and that multiple degassing events have been analyzed and compared at this location. Both events resulted in significant changes in cloud effective radius and cloud droplet number concentration that were decoupled from local meteorology and in line with an enhanced cloud albedo. However, it is likely that the effects of volcanic emissions on liquid water path and cloud fraction were largely offset by meteorological variability. Comparison of cloud anomalies between the two events suggested a threshold response of aerosol–cloud interactions to overcome meteorological effects, largely controlled by aerosol loading. In both events, the ingestion of aerosols within convective parcels enhanced the detrainment of condensate in the upper troposphere, resulting in deeper clouds than observed under pristine conditions. Accounting for ice nucleation on ash particles led to enhanced ice crystal concentrations at cirrus levels and a slight decrease in ice water content, improving the correlation of the model results with the satellite retrievals. Overall, aerosol loading, plume characteristics, and meteorology contributed to changes in cloud properties during the Kilauea degassing events.

Katherine H. Breen↗
DOE OSTI2020

Relationships between Immersion Freezing and Crystal Habit for Arctic Mixed-Phase Clouds—A Numerical Study

Abstract The number concentration of ice particles in Arctic mixed-phase clouds is a major controlling factor of cloud lifetime. The relationships between ice nucleation mode and ice crystal habit development are not yet constrained by observations. This study uses a habit-predicting microphysical scheme within a 3D large-eddy simulation model to evaluate the relationship between immersion freezing and ice habit in a simulated Arctic mixed-phase cloud case. Three immersion freezing parameterizations are considered: a volume-dependent freezing scheme (VF), a parameterization limited to activated droplets (C-AC), and a parameterization limited to coarse aerosol particles (C-CM). Both C-AC and C-CM are based on classical nucleation theory. The freezing rate with VF is found to be greater in downdraft regions than in updraft regions due to the downdraft having a higher number concentration of large droplets. The C-AC cases show active freezing of small droplets near cloud top, whereas in the C-CM cases, mainly the 8–32- μ m-sized droplets freeze in updraft regions near the cloud base. Because the initial crystal size is assumed to affect the axis ratio of hexagonal plates, the VF cases produce crystals with larger axis ratios, resulting in smaller mode radii than the C-AC cases. In all cases, irregular polycrystals dominate near cloud top and a band-like structure develops within the cloud, which qualitatively agrees with previous observations. In the VF and C-CM cases, unactivated large droplets arising from coarse-mode aerosol particles contributed significantly to the freezing rate, producing an important influence on crystal habit.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Improving GCM Predictability of Mixed-Phase Clouds and Aerosol Interactions at High Latitudes with ARM Observations

The overachieving goal of this project is to improve the predictability of mixed-phase clouds and aerosol interactions in the Community Atmosphere Model version 6 (CAM6) through comparison with the ARM observations. There are three main objectives of the proposed study: (1) Improve the representation of ice microphysical processes in mixed-phase clouds; (2) Test the performance of ice microphysics in CESM-CAM6 with the ARM observations in northern and southern high latitudes; and (3) Examine mixed-phase cloud microphysics-aerosol-turbulence-radiation interactions in CESM-CAM6. In this project, we have (1) Improved the representation of ice microphysical processes in mixed-phase clouds in CESM-CAM6 by implementing the marine organic aerosol (MOA) and treating the ice nucleating particles (INPs) from MOA and its impacts on mixed-phase clouds. We improved the treatment of ice depositional growth through the Wegener–Bergeron–Findeisen (WBF) process by considering the subgrid heterogeneous distributions between liquid droplets and ice crystals in mixed-phase clouds; (2) Tested the performance of ice microphysics in CESM-CAM6 with the ARM observations at high latitudes. We compared the simulated INP concentrations with the ARM observations, e.g., from M-PACE, ISDAC, INPOP, and other data (Mace Head, Zeppelin, CAPRICORN). We examined the impact of improved WBF treatment on model simulated Arctic mixed-phase clouds observed in the M-PACE field campaign. Seasonal variations of modeled mixed-phase cloud properties (LWO, IWP) are compared with the ground-based remote sensing retrievals at the ARM’s NSA $Utqia\dot{g}vik$ site; and (3) Examined mixed-phase cloud microphysics-aerosol-dynamics-radiation interactions in CESM-CAM6 that include the impacts of MOA INPs, and impacts of different model parameterizations (CLUBB versus UW turbulence & shallow convection schemes, MG2 versus MG1) on high-latitude mixed-phase cloud properties. Aerosol indirect effects of MOA through the liquid phase (droplet activation) and ice phase processes (e.g., the glaciation indirect effect) were investigated.

54 ENVIRONMENTAL SCIENCES↗