Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fracturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Fracture characteristics of angleplied laminates fabricated from overaged graphite/epoxy prepreg

A series of angleplied graphite/epoxy laminates was fabricated from overaged prepreg and tested in tension to investigate the effects of overaged or advanced cure material on the degradation of laminate strength. Results, which include fracture stresses, indicate a severe degradation in strength. In addition, the fracture surfaces and microstructural characteristics are distinctly unlike any features observed in previous tests of this prepreg and laminate configuration. Photographs of the surfaces and microstructures reveal flat morphologies consisting of alternate rows of fibers and hackles. These fracture surface characteristics are independent of the laminate configurations. The photomicrographs are presented and compared with data from similar studies to show the unique characteristics produced by the overage prepreg. Analytical studies produced results which agreed with those from the experimental investigations.

Ginty, Carol A.↗

Fracture surfaces of irradiated composites

Electron microscopy was used to analyze the fracture surfaces of T300/934 graphite/epoxy unidirectional off-axis tensile coupons which were subjected to 1.0-MeV electron radiation at a rate of 50 Mrad/h for a total dose of 10 Grad. Fracture surfaces from irradiated and nonirradiated specimens tested at 116 K, room temperature, and 394 K were analyzed to assess the influence of radiation and temperature on the mode of failure and variations in constituent material as a function of environmental exposure. Micrographs of fracture surfaces indicate that irradiated specimens are more brittle than nonirradiated specimens at low temperatures. However, at elevated temperatures the irradiated specimens exhibit significantly more plasticity than nonirradiated specimens.

Milkovich, Scott M.↗

Semi-interpenetrating polymer network's of polyimides: Fracture toughness

The objective was to improve the fracture toughness of the PMR-15 thermosetting polyimide by co-disolving LaRC-TPI, a thermoplastic polyimide. The co-solvation of a thermoplastic into a thermoset produces an interpenetration of the thermoplastic polymer into the thermoset polyimide network. A second research program was planned around the concept that to improve the fracture toughness of a thermoset polyimide polymer, the molecular weight between crosslink points would be an important macromolecular topological parameter in producing a fracture toughened semi-IPN polyimide.

Hansen, Marion Glenn↗

An experimental investigation of the fracture behavior of thick, notched laminated composites

The fracture of high-modulus fiber-reinforced graphite/epoxy laminates with machined crack-like notches is discussed. An experimental program was conducted, in which stacking sequence,laminate thickness, notch size, and specimen configuration have been investigated. This research has led to the fundamental observation that heterogeneity significantly effects the fracture of thin laminates but has a relatively insignificant effect on the fracture of thick laminates. The results of this program are reviewed with the emphasis on the notch sensitivity and design of thick laminates.

Harris, Charles E.↗

Finite element methods in fracture mechanics

Finite-element methodology specific to the analysis of fracture mechanics problems is reviewed. Primary emphasis is on the important algorithmic developments which have enhanced the numerical modeling of fracture processes. Methodologies to address elastostatic problems in two and three dimensions, elastodynamic problems, elastoplastic problems, special considerations for three-dimensional nonlinear problems, and the modeling of stable crack growth are reviewed. In addition, the future needs of the fracture community are discussed and open questions are identified.

Liebowitz, H.↗

Structural behavior of composites with progressive fracture

The objective of the study is to unify several computational tools developed for the prediction of progressive damage and fracture with efforts for the prediction of the overall response of damaged composite structures. In particular, a computational finite element model for the damaged structure is developed using a computer program as a byproduct of the analysis of progressive damage and fracture. Thus, a single computational investigation can predict progressive fracture and the resulting variation in structural properties of angleplied composites.

Minnetyan, L.↗

Martian tension fractures and the formation of grabens and collapse features at Valles Marineris

Simple models of the Martian crust are summarized that predict extensional deformation style on the basis of depth, material friction and strength, and hydraulic conditions appropriate to the planet. These models indicate that tension fractures may be common features on Mars, given adequate differential stress conditions. Examples of tension fractures on Mars inferred from morphological criteria are examined based on the probable geologic conditions in which they formed and on model constraints. It is proposed that the grabens and collapse features of Valles Marineris are controlled by tension fractures in intact basement rocks that lie below impact ejecta.

Tanaka, K. L.↗

Indentation fracture toughness of sintered silicon carbide in the Palmqvist crack regime

The fracture toughness of a sintered dense alpha-SiC was estimated by the Vickers indentation microfracture method in the low-load Palmqvist crack regime. It was observed that the use of simultaneously obtained Vickers hardnesses does not yield reliable fracture toughness values, nor does application of the median-crack-derived equations. It is necessary to utilize a load-independent, crack-free hardness value with this toughness estimation method. Although several of the curve-fitting equations yield similar toughnesses, it is concluded for the Palmqvist crack system in this alpha-SiC that the Niihara-Morena-Hasselman (1982) equation is the only one which yields fracture toughness values in agreement with conventional measurement techniques.

Li, Zhuang↗

Nonlinear fracture of concrete and ceramics

The nonlinear fracture process zones in an impacted unnotched concrete bend specimen, a prenotched ceramic bend specimen, and an unnotched ceramic/ceramic composite bend specimen were estimated through hybrid experimental numerical analysis. Aggregate bridging in concrete, particulate bridging in ceramics, and fiber bridging in ceramic/ceramic composite are modeled by Barenblatt-type cohesive zones which are incorporated into the finite-element models of the bend specimens. Both generation and propagation analyses are used to estimate the distribution of crack closure stresses in the nonlinear fracture process zones. The finite-element models are then used to simulate fracture tests consisting of rapid crack propagation in an impacted concrete bend specimen, and stable crack growth and strain softening in a ceramic and ceramic/ceramic composite bend specimens.

Kobayashi, Albert S.↗

Deformation and fracture of single-crystal and sintered polycrystalline silicon carbide produced by cavitation

An investigation was conducted to examine the deformation and fracture behavior of single-crystal and sintered polycrystalline SiC surfaces exposed to cavitation. Cavitation erosion experiments were conducted in distilled water at 25 C by using a magnetostrictive oscillator in close proximity (1 mm) to the surface of SiC. The horn frequency was 20 kHz, and the double amplitude of the vibrating disk was 50 microns. The results of the investigation indicate that the SiC (0001) surface could be deformed in a plastic manner during cavitation. Dislocation etch pits were formed when the surface was chemically etched. The number of defects, including dislocations in SiC (0001) surface, increased with increasing exposure time to cavitation. The presence of intrinsic defects such as voids in the surficial layers of the sintered polycrystalline SiC determined the zones at which fractured grains and fracture pits (pores) were generated. Single-crystal SiC had superior erosion resistance to that of sintered polycrystalline SiC.

Miyoshi, Kazuhisa↗

Structural behavior of composites with progressive fracture

Structural characteristics such as natural frequencies and buckling loads with corresponding mode shapes were investigated during progressive fracture of multilayer, angle-plied polymer matrix composites. A computer program was used to generate the numerical results for overall mechanical response of damaged composites. Variations in structural characteristics as a function of the previously applied loading were studied. Results indicate that most of the overall structural properties were preserved throughout a significant proportion of the ultimate fracture load. For the cases studied, changes in structural behavior began to occur after 70 percent of the ultimate fracture load was applied. However, the individual nature of the structural change was rather varied depending on the laminate configuration, fiber orientation, and the boundary conditions.

Minnetyan, Levon↗

Impact fracture experiments simulating interstellar grain-grain collisions

Oxide and silicate grains condensing during the early phases of the formation of the solar system or in the outflow of stars are exposed to high partial pressures of the low-z elements H, C, N and O and their simple gaseous compounds. Though refractory minerals are nominally anhydrous and non-carbonate, if they crystallize in the presence of H2O, N2 and CO or CO2 gases, they dissolve traces of the gaseous components. The question arises: How does the presence of dissolved gases or gas components manifest itself when grain-grain collisions occur. What are the gases emitted when grains are shattered during a collision event. Researchers report on fracture experiments in ultrahigh vacuum (UHV, approximately less than 10 to the -8th power mbar) designed to measure (by means of a quadrupole mass spectrometer, QMS, with microns to ms time resolution) the emission of gases and vapors during and after impact (up to 1.5 sec). Two terrestrial materials were chosen which represent structural and compositional extremes: olivine (San Carlos, AZ), a densely packed Mg-Fe(2+) silicate from the upper mantle, available as 6 to 12 mm single crystals, and obsidian (Oregon), a structurally open, alkaline-SiO2-rich volcanic glass. In the olivine crystals OH- groups have been identified spectroscopically, as well as H2 molecules. Obsidian is a water-rich glass containing OH- besides H2O molecules. Olivine from the mantle often contains CO2, either as CO2-rich fluid in fluid inclusions or structurally dissolved or both. By analogy to synthetic glasses CO2 in the obsidian may be present in form of CO2 molecules in voids of molecular dimensions, or as carbonate anions, CO3(2-). No organic molecules have been detected spectroscopically in either material. Results indicate that refractory oxide/silicates which contain dissolved traces of the H2O and CO/CO2 components but no spectroscopically detectable traces of organics may release complex H-C-O (possibly H-C-N-O) molecules upon fracture, plus metal vapor. This points: (1) at complex reaction mechanisms between dissolved H2O, CO/CO2 (and N2) components within the mineral structure or during fracture, and (2) at the possibility that similar emission processes occur following grain-grain collisions in interstellar dust clouds.

Freund, Friedemann↗

Observations of winter polynyas and fractures using NOAA AVHRR TIR images and Nimbus-7 SMMR sea ice concentration charts

The validity of the daily sea ice concentration charts obtained from Nimbus-7 SMMR data is tested against thermal IR NOAA AVHRR-4 images with a 1.1 x 1.1 km resolution. Polynyas and fractures recorded in both data sets are compared for the same times over the same areas. Although the coarser resolution of SMMR data leads to a loss of detail, it is found that the ice concentration charts provide valuable data on openings in the ice. The SMMR data on the location, orientation, and size of polynyas and fractures are shown to be in good agreement with the AVHRR data. Also, the results suggest that the location and orientation of plynyas and fractures are related to the direction of surface winds.

Dey, B.↗

Effects of loading rate and temperature on dynamic fracture of ceramic matrix composites

A hybrid experimental-numerical procedure was used to determine the dynamic fracture initiation toughnesses and the dynamic stress intensity factors of alumina, TiB2-particulate/SiC-matrix, and SiC(w)/Al2O3-matrix composites at room and elevated temperatures under static and impact loadings. The dynamic fracture initiation toughnesses at room and elevated temperatures were greater than the corresponding static fracture toughness. The crack velocity versus the dynamic stress intensity factor relations showed minor differences due to temperature changes but significant differences due to the change in loading rates.

Yang, K. H.↗

Dynamic fracture responses of alumina and two ceramic composites

A hybrid experimental-numerical procedure was used to characterize the dynamic fracture response of Al2O3 and TiB2-particulate/SiC-matrix and SiC-whisker/Al2O3-matrix composites. Unlike metals and polymers, dynamic arrest stress intensity factors (SIFs) did not exist in the monolithic ceramics and the two ceramic composites considered. Thus a running crack in these materials cannot be arrested by lowering the driving force, i.e., the dynamic SIF. Fractography study of the alumina specimens showed that the area of transgranular failure varied from about 3 percent to about 16 percent for rapid crack extensions in statically and impact loaded specimens, respectively. The influence of kinematic constraints which enforces transgranular flat crack extension, despite the higher fracture energy of transgranular fracture, is discussed.

Yang, Kwan-Ho↗

The mechanisms of dispersion strengthening and fracture in Al-based XD(tm) alloys, part 1

The influence of reinforcement size, volume fraction, and matrix deformation behavior on room and elevated temperature strength; the fracture toughness; and the fatigue crack growth rate of metal matrix composites of Al-4(pct)Cu-1.5(pct)Mg with TiB2 were examined. The influence of reinforcement volume fraction was also examined for pure aluminum with TiB2. Higher TiB2 volume fractions increased the tensile yield strength at both room and elevated temperatures, and reduced the elongation to fracture. Tensile tests also indicate that small particles provided a greater increase in strength for a given volume fraction than larger particles, whereas elongation to fracture appeared to be insensitive to reinforcement size. Interparticle spacing appears to be the factor that controls the strength of these alloys, with the exact nature of the dependence relying on the nature of dislocation slip in the matrix (planar vs. diffuse). The isothermal aging response of the precipitation strengthened Al-4(pct)Cu-1.5(pct)Mg alloys was not accelerated by the presence of TiB2. Cold work prior to artificial aging created additional geometrically necessary dislocations which serve as heterogeneous nucleation sites leading to accelerated aging, a finer precipitate size, and an increase in the strength of the alloy.

Aikin, R. M., Jr.↗

Elevated temperature fracture of RS/PM aluminum alloy 8009

The fracture behavior of advanced powder metallurgy Al-Fe-V-Si alloy 8009 (previously called FVS0812) is being characterized under monotonic loads, as a function of temperature. Particular attention is focused on contributions to the fracture mechanism from the fine grained dispersoid strengthened microstructure, dissolved solute from rapid solidification, and the moist air environment. Time-dependent crack growth is characterized in advanced aluminum alloys at elevated temperatures with the fracture mechanics approach, and cracking mechanisms are examined with a metallurgical approach. Specific tasks were to obtain standard load crack growth experimental information from a refined testing system; to correlate crack growth kinetics with the j-integral and time dependent C(sub t)(t); and to investigate the intermediate temperature embrittlement of 8009 alloy in order to understand crack growth mechanisms.

Porr, William C., Jr.↗

Influence of dissolved hydrogen on aluminum-lithium alloy fracture behavior

The objective of this work is to study the effects of dissolved hydrogen on the mechanical properties of 2090 and 2219 alloys. Prior to mechanical testing, potentiostatic and potentiodynamic tests were performed using NaCl/HCl solutions varying in pH from 1.5 to 7.5 (3.5 pct NaCl in deionized water). After analysis of the potentiodynamic curve for each solution, several potentiostatic experiments were conducted for various times (from 10 minutes to several hours) with a cathodic overpotential of 300 mV. These experiments were performed to select charging conditions. It is shown that the fracture of L-S and T-S orientations proceeds via slipping of layers in the S-T direction. The T-S and L-S orientations fractured with substantially higher propagation energy that the L-T and T-L orientations, due in large part to the extensive delamination propagation of the fracture.

Rivet, F. C.↗