Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flexible electronics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

A Generic Sacrificial Layer for Wide-Range Freestanding Oxides with Modulated Magnetic Anisotropy

Freestanding oxide nanomembranes have promising applications because of their novel electronic states and flexible crystalline structures. Several materials have been developed as sacrificial layers to exfoliate thin films from substrates via wet-etching. However, these materials face great challenges in terms of either complicated crystalline structures or corrosive solutions. Herein, a new sacrificial material, SrCoO 2.5 , is presented, which can be coherently grown with wide-range strains and crystalline orientations and is also soluble in eco-friendly solutions such as acetic acid, vinegar, and even carbonated drinks. With SrCoO 2.5 as the sacrificial layer, high-quality freestanding ferromagnetic SrRuO 3 membranes are achieved from wide-range epitaxial strains and different crystalline orientations. By investigating the evolution of the magnetic properties of these samples, it is discovered that epitaxial strain causes a distinct modification of the magnetic anisotropy of (001) pc -oriented SrRuO 3 samples, while its influence on the (110) pc and (111) pc samples is insignificant. This study not only demonstrates the freestanding SrRuO 3 as a promising material for flexible spintronic devices, but also offers a great opportunity to engineer a wide range of strained and oriented complex oxides for novel freestanding electronics using this newly developed sacrificial material.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Large-sized out-of-plane stretchable electrodes based on poly-dimethylsiloxane substrate

This paper describes a reliable fabrication method of stretchable electrodes based on poly-dimethylsiloxane (PDMS) substrate. The electrode traces and pads were formed in out-of-plane structures to improve the flexibility and stretchability of the electrode array. The suspended traces and pads were attached to the PDMS substrate via parylene posts that were located nearby the traces and under the pads. As only conventional micro-electro-mechanical systems techniques were used, the out-of-plane electrode arrays were clearly fabricated at wafer level with high yield and reliability. Also, bi-layer out-of-plane electrodes were formed through additional fabrication steps in addition to mono-layer out-of-plane electrodes. The mechanical characteristics such as the stretchability, flexibility, and foldability of the fabricated electrodes were evaluated, resulting in stable electrical connection of the metal traces with up to 32.4% strain and up to 360° twist angle over 25 mm. The durability in stretched condition was validated by cyclic stretch test with 10% and 20% strain, resulting in electrical disconnection at 8600 cycles when subjected to 20% strain. From these results, it is concluded that the proposed fabrication method produced highly reliable, out-of-plane and stretchable electrodes, which would be used in various flexible and stretchable electronics applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2016

Optical and electrical properties of Cu-based all oxide semi-transparent photodetector

Zero-bias operating Cu oxide-based photodetector was achieved by using large-scale available sputtering method. Cu oxide (Cu{sub 2}O or CuO) was used as p-type transparent layer to form a heterojunction by contacting n-type ZnO layer. All metal-oxide materials were employed to realize transparent device at room temperature and showed a high transparency (>75% at 600 nm) with excellent photoresponses. The structural, morphological, optical, and electrical properties of Cu oxides of CuO and Cu{sub 2}O are evaluated in depth by UV-visible spectrometer, X-ray diffraction, scanning electron microscopy, atomic force microscopy, Kelvin probe force microscopy, and Hall measurements. We may suggest a route of high-functional Cu oxide-based photoelectric devices for the applications in flexible and transparent electronics.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2015

A hydrogel capsule as gate dielectric in flexible organic field-effect transistors

A jellified alginate based capsule serves as biocompatible and biodegradable electrolyte system to gate an organic field-effect transistor fabricated on a flexible substrate. Such a system allows operating thiophene based polymer transistors below 0.5 V through an electrical double layer formed across an ion-permeable polymeric electrolyte. Moreover, biological macro-molecules such as glucose-oxidase and streptavidin can enter into the gating capsules that serve also as delivery system. An enzymatic bio-reaction is shown to take place in the capsule and preliminary results on the measurement of the electronic responses promise for low-cost, low-power, flexible electronic bio-sensing applications using capsule-gated organic field-effect transistors.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Significant improvement of conversion efficiency by passivation of low-angle grain boundaries in flexible low-cost single-crystal-like GaAs thin-film solar cells directly deposited on metal tape

We develop an easily implementable yet effective process to achieve high power conversion efficiency in newly-developed flexible single-crystal-like GaAs thin-film photovoltaic solar cells on cheap metal tape. We study various techniques on the fabricated devices to passivate the defect states associated with dangling bonds at low-angle grain boundaries (LA-GBs) existing in the single-crystal-like GaAs material. We report that sulfur by trioctylphosphine sulfide (TOP:S) solution treatment can partially but effectively passivate the defect states at the LA-GBs to increase all the solar cell performance parameters of open-circuit voltage VOC (33.2%), short-circuit current JSC (19.5%), and fill factor FF (25.8%), resulting in the improvement of the power conversion efficiency more than double. The material and device characterizations and numerical modeling are performed to propose a mechanism, also suggesting that the power conversion efficiency higher than 20%, which is an important target milestone in emerging solar cell technologies, can be achieved. This work presents the first effective passivation of the bulk defects in GaAs at the device level and can also offer a solution for other photonic and electronic devices using non-single-crystalline GaAs films for flexible electronics.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Nanoscale Investigation of Grain Boundary Characteristics of Single-Crystalline-Like GaAs Films and Solar Cells on Flexible Metal Substrates

High-resolution imaging with nanometer spatial resolution was carried out to unravel the grain and grain boundary (GB) properties of single-crystalline-like n-type GaAs films and single-junction solar cells on epi-ready flexible metal substrates. Electron Back Scattered Diffraction studies revealed ultra-low angle GBs with the presence of twin boundaries. The pn junction carrier collection properties were directly imaged using cross-sectional Electron Beam Induced Current measurements. Low-temperature Cathodoluminescence imaging indicated a strong component of optical emission from the GBs. Comprehensive studies of the structural, chemical, optical and electrical properties were carried out to unravel the fundamental GB properties of flexible GaAs films on metal substrates.

14 SOLAR ENERGY↗
DOE OSTI2017

Flexible, cluster-based analysis of the electronic medical record of sepsis with composite mixture models

The widespread adoption of electronic medical records (EMRs) in healthcare has provided vast new amounts of data for statistical machine learning researchers in their efforts to model and predict patient health status, potentially enabling novel advances in treatment. In the case of sepsis, a debilitating, dysregulated host response to infection, extracting subtle, uncataloged clinical phenotypes from the EMR with statistical machine learning methods has the potential to impact patient diagnosis and treatment early in the course of their hospitalization. However, there are significant barriers that must be overcome to extract these insights from EMR data. First, EMR datasets consist of both static and dynamic observations of discrete and continuous-valued variables, many of which may be missing, precluding the application of standard multivariate analysis techniques. Second, clinical populations observed via EMRs and relevant to the study and management of conditions like sepsis are often heterogeneous; properly accounting for this heterogeneity is critical. Here, we describe an unsupervised, probabilistic framework called a composite mixture model that can simultaneously accommodate the wide variety of observations frequently observed in EMR datasets, characterize heterogeneous clinical populations, and handle missing observations. In conclusion, we demonstrate the efficacy of our approach on a large-scale sepsis cohort, developing novel techniques built on our model-based clusters to track patient mortality risk over time and identify physiological trends and distinct subgroups of the dataset associated with elevated risk of mortality during hospitalization.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2019

Structure and Electronic Properties of InSb Nanowires Grown in Flexible Polycarbonate Membranes

A dense array of vertically aligned indium antimonide (InSb) nanowires with high aspect ratio (diameter 150 nm, length 20 μ m) were grown in the pores of a track-etched polycarbonate membrane via a one-step electrochemical method. There are several reports on InSb nanowire growth in the pores of a mechanically rigid, nano-channel alumina template (NCA), where nanowire growth occurs in the pores of the NCA. This work on InSb nanowire growth in pores of track-etched polycarbonate (PC) membrane sheds light on the various factors that affect nucleation and nanowire growth. The average length and diameter of the as-grown nanowires was about 10 μ m and 150 nm, respectively. Two possible mechanisms accounting for two different morphologies of the as-grown nanowires are proposed. The polycrystallinity observed in some of the nanowires is explained using the 3D ‘nucleation-coalescence’ mechanism. On the other hand, single crystal nanowires with a high density of twin defects and stacking faults grow epitaxially by a two-dimensional (2D) nucleation/growth mechanism. To assess the electrical quality of the nanowires, two- and four-terminal devices were fabricated using a single InSb nanowire contacted by two Ni electrodes. It was found that, at low bias, the ohmic current is controlled by charge diffusion from the bulk contacts. On the other hand, at high bias, the effects of space charge limited current (SCLC) are evident in the current–voltage behavior, characteristic of transport through structures with reduced electrostatic screening. A cross-over from ohmic to SCLC occurs at about 0.14 V, yielding a free carrier concentration of the order of 10 14 cm -3 .

36 MATERIALS SCIENCE↗
NASA NTRS1969

Flexible high-voltage supply for experimental electron microscope

Scanning microscope uses a field-emission tip for the electron source, an electron gun that simultaneously accelerates and focuses electrons from the source, and one auxiliary lens to produce a final probe size at the specimen on the order of angstroms.

Chapman, G. L.↗
DOE OSTI2025

Bilayer Electron Transport Layers for High–Performance Rigid and Flexible Perovskite Solar Cells

While great progress is being made in achieving high power conversion efficiency (PCE), durability, and reliability in rigid and flexible n–i–p perovskite solar cells (PSCs), there is still room for improvement. Among myriad ways this can be achieved, one way is to improve the processing and quality of electron transport layers (ETLs) used in PSCs. To that end, here we explore the use of SnO 2 /TiO 2 bilayer ETLs in both rigid and flexible PSCs. In the case of rigid PSCs, chemical bath deposition (CBD) is used where the bilayer architecture affords the CBD of high-quality ETL, which results in PSCs with up to 25.13% PCE and operational stability T 80 (80% of initial PCE retained) of 2220 h under 1-sun continuous illumination with maximum power-point tracking. In the case of flexible PSCs, once again, the bilayer architecture allows us to fabricate high-quality ETL using spin coating, which results in PSCs with up to 22.54% PCE and excellent mechanical durability, withstanding 20 000 bending cycles with ≈92% of the initial PCE retained. Mechanisms underlying the enhanced performance and stability/durability of rigid and flexible PSCs that use SnO 2 /TiO 2 bilayer ETLs are elucidated. Furthermore, this approach could be extended to other ETL systems for PSCs for further improvements in PCE, durability, and reliability.

14 SOLAR ENERGY↗
NASA NTRS2002

Architectural study of active membrane antennas

One method to dramatically reduce the weight, volume and associated cost of space-based SyntheticAperture Radars (SAR) is to replace the conventional rigid manifold antenna architecture with a flexible thin-film membrane. This has been successfully demonstrated as a passive array. To further reduce the cost and weight and provide 2D scanning required by space-based applications we also need to integrate the Transmit/Receive (TR) function into the inflatable antenna elements. This paper explores the constraints that must be placed on the active electronics of a flexible antenna array as well as some of the preliminary work in this area.

active membrane antenna SAR Synthetic Aperture Rad↗
DOE OSTI2019

Energy storage: The future enabled by nanomaterials

Lithium-ion batteries, which power portable electronics, electric vehicles, and stationary storage, have been recognized with the 2019 Nobel Prize in chemistry. The development of nanomaterials and their related processing into electrodes and devices can improve the performance and/or development of the existing energy storage systems. We provide a perspective on recent progress in the application of nanomaterials in energy storage devices, such as supercapacitors and batteries. The versatility of nanomaterials can lead to power sources for portable, flexible, foldable, and distributable electronics; electric transportation; and grid-scale storage, as well as integration in living environments and biomedical systems. To overcome limitations of nanomaterials related to high reactivity and chemical instability caused by their high surface area, nanoparticles with different functionalities should be combined in smart architectures on nano- and microscales. The integration of nanomaterials into functional architectures and devices requires the development of advanced manufacturing approaches. We discuss successful strategies and outline a roadmap for the exploitation of nanomaterials for enabling future energy storage applications, such as powering distributed sensor networks and flexible and wearable electronics.

catalysis (heterogeneous)↗
DOE OSTI2014

Laser-Induced Self-Assembled Nanostructures on Electron-Transparent Substrates

Currently, one of the challenges in high-resolution transmission electron microscopy (TEM) studies of nanomaterials is to make contamination-free materials in a simple and time-efficient way. We demonstrate a method that combines nanosecond-pulsed laser dewetting of thin films with a film float-off technique to realize nanostructures (NSs) on electron-transparent substrates in a robust and rapid manner. NSs of metal (Ag) and bimetals (AgCo, AuCo) ranging from 20 to 150 nm are synthesized on thin carbon film deposited on mica substrates. The NS/carbon system is subsequently transferred onto TEM grids by a float-off process resulting from debonding of the carbon from mica due to their contrasting hydrophobic nature. Our process enables the fabrication of different NSs on flexible and electron-transparent substrates.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Laser-Induced Carbon-Based Smart Flexible Sensor Array for Multiflavors Detection

We report a flexible sensor array electronic tongue system that is fabricated on a polymer substrate by the laser direct writing process for multiflavor detection. Electronic tongue is a sensing system that is applied to detect different elements with the same sensor array. By analyzing responses from different measurement units, it enables a cross-sensitivity, namely, the ability of the system to responding to a range of different analytes in solution without specific functionalization of sensors. In this article, a six-unit sensing array system was fabricated by a laser direct writing process. Sensing units were introduced on a flexible polyamide surface. A high surface–volume ratio porous carbon structure was created by a laser-induced carbonization process, which provides stable conductive carbon electrodes with high sensitivity. Different surface treatments, such as gold plating, reduced-graphene oxide coating, and polyaniline coating, were accomplished for different measurement units. By applying principal component analysis, this sensing system shows a promising result for the detection of multiple flavors. The detection limit for each element is about 0.1 mM for NaCl and sugar solutions. Also, it is able to detect 10 –4 times diluted commercial table vinegar solution, which originally contains 5% acetic acid. The detection limit is theoretically lower than the human threshold of 10 mM for NaCl and sugar. Besides, the sensing system shows a high sensitivity and selectivity for mixed elements. Here, by mapping the data points, the sensor system could detect flavor combinations and provide a reliable prediction of analyte concentration ratios.

47 OTHER INSTRUMENTATION↗
DOE OSTI2018

Scientists Print All-Liquid 3-D Structures

Berkeley Lab scientists have developed a way to print 3-D structures composed entirely of liquids. Using a modified 3-D printer, they injected threads of water into silicone oil — sculpting tubes made of one liquid within another liquid. They envision their all-liquid material could be used to construct liquid electronics that power flexible, stretchable devices. The scientists also foresee chemically tuning the tubes and flowing molecules through them, leading to new ways to separate molecules or precisely deliver nanoscale building blocks to under-construction compounds.

3-D LIQUID STRUCTURES↗
NASA NTRS1997

Computational Study of Electron-Molecule Collisions Related to Low-Temperature Plasmas

Computational study of electron-molecule collisions not only complements experimental measurements, but can also be used to investigate processes not readily accessible experimentally. A number of ab initio computational methods are available for these types of calculations. Here we describe a recently developed technique, the finite element Z-matrix method, Analogous to the R-matrix, method, it partitions the space into regions and employs real matrix elements. However, unlike the implementation of the R-matrix method commonly used in atomic and molecular physics, the Z-matrix method is fully variational. In the present implementation, a mixed basis of finite elements and Gaussians is used to represent the continuum electron, thus offering full flexibility without imposing fixed boundary conditions. Numerical examples include the electron-impact dissociation of N2 via the metastable A3Su+ state, a process which may be important in the lower thermosphere, and the dissociation of the CF radical, a process of interest to plasma etching. To understand the dissociation pathways, large scale quantum chemical calculations have been carried out for all target states which dissociate to the lowest five limits in the case of N2, and to the lowest two limits in the case of CF. For N2, the structural calculations clearly show the preference for predissociation if the initial state is the ground X1 Sg+ state, but direct dissociation appears to be preferable if the initial state is the A3Su+ state. Multi-configuration SCF target functions are used in the collisional calculation.

Huo, Winifred M.↗