Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fiber composites”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Graphite fiber polyimide composites for spherical bearings to 340 C (650 F)

Journal bearings with self-alining spherical elements of graphite-fiber-reinforced-polyimide composites were tested from 24 to 340 C (75 to 650 F) at unit loads up to 3.5 times 10 to the 7th power N/sq m (5000 psi). The journal oscillated in the cylindrical bore of the composite element + or - 15 deg at 1 hertz. Outer races and journals were metal hardened of Rockwell C-32 and finished to 10 to the minus 7th power m. A 45 wt. percent graphite-fiber composite gave low friction (0.08 to 0.13), low wear, and almost no plastic deformation under any of the test conditions. Composites with 15 and 25 wt. percent graphite fiber failed by plastic deformation at 315 C (600 F) and 3.5 times 10 to the 7th power N/sq m (5000 psi). A composite with 60 wt. percent graphite fiber failed by brittle fracture under the same conditions, but had very low friction coefficients (0.05 to 0.10) and may be a good bearing material at lighter loads.

Sliney, H. E.↗
NASA NTRS1992

CVD of silicon carbide on structural fibers: Microstructure and composition

Structural fibers are currently being considered as reinforcements for intermetallic and ceramic materials. Some of these fibers, however, are easily degraded in a high temperature oxidative environment. Therefore, coatings are needed to protect the fibers from environmental attack. Silicon carbide (SiC) was chemically vapor deposited (CVD) on Textron's SCS6 fibers. Fiber temperatures ranging from 1350 to 1500 C were studied. Silane (SiH4) and propane (C2H8) were used for the source gases and different concentrations of these source gases were studied. Deposition rates were determined for each group of fibers at different temperatures. Less variation in deposition rates were observed for the dilute source gas experiments than the concentrated source gas experiments. A careful analysis was performed on the stoichiometry of the CVD SiC coating using electron microprobe. Microstructures for the different conditions were compared. At 1350 C, the microstructures were similar; however, at higher temperatures, the microstructure for the more concentrated source gas group were porous and columnar in comparison to the cross sections taken from the same area for the dilute source gas group.

Veitch, Lisa C.↗
NASA NTRS1992

CVD of silicon carbide on structural fibers - Microstructure and composition

Structural fibers are currently being considered as reinforcements for intermetallic and ceramic materials. Some of these fibers, however, are easily degraded in a high temperature oxidative environment. Therefore, coatings are needed to protect the fibers from environmental attack. Silicon carbide (SiC) was chemically vapor deposited (CVD) on Textron's SCS6 fibers. Fiber temperatures ranging from 1350 to 1500 C were studied. Silane (SiH4) and propane (C2H8) were used for the source gases and different concentrations of these source gases were studied. Deposition rates were determined for each group of fibers at different temperatures. Less variation in deposition rates were observed for the dilute source gas experiments than the concentrated source gas experiments. A careful analysis was performed on the stoichiometry of the CVD SiC coating using electron microprobe. Microstructures for the different conditions were compared. At 1350 C, the microstructures were similar; however, at higher temperatures, the microstructure for the more concentrated source gas group were porous and columnar in comparison to the cross sections taken from the same area for the dilute source gas group.

Veitch, Lisa C.↗
NASA NTRS1988

Mechanical properties of neat polymer matrix materials and their unidirectional carbon fiber-reinforced composites

The mechanical properties of two neat resin systems for use in carbon fiber epoxy composites were characterized. This included tensile and shear stiffness and strengths, coefficients of thermal and moisture expansion, and fracture toughness. Tests were conducted on specimens in the dry and moisture-saturated states, at temperatures of 23, 82 and 121 C. The neat resins tested were American Cyanamid 1806 and Union Carbide ERX-4901B(MPDA). Results were compared to previously tested neat resins. Four unidirectional carbon fiber reinforced composites were mechanically characterized. Axial and transverse tension and in-plane shear strengths and stiffness were measured, as well as transverse coefficients of thermal and moisture expansion. Tests were conducted on dry specimens only at 23 and 100 C. The materials tested were AS4/3502, AS6/5245-C, T300/BP907, and C6000/1806 unidirectional composites. Scanning electron microscopic examination of fracture surfaces was performed to permit the correlation of observed failure modes with the environmental test conditions.

Zimmerman, Richard S.↗
NASA NTRS1989

Mechanical properties of several neat polymer matrix materials and unidirectional carbon fiber-reinforced composites

The mechanical and physical properties of three neat matrix materials, i.e., PEEK (polyetheretherketone) thermoplastic, Hexcel F155 rubber-toughened epoxy and Hercules 8551-7 rubber-toughened epoxy, were experimentally determined. Twelve unidirectional carbon fiber composites, incorporating matrix materials characterized in this or earlier studies (with one exception; the PISO(sub 2)-TPI matrix itself was not characterized), were also tested. These composite systems included AS4/2220-1, AS4/2220-3, T500/R914, IM6/HX1504, T300/4901A (MDA), T700/4901A (MDA), T300/4901B (MPDA), T700/4901B (MPDA), APC2 (AS4/PEEK, ICI), APC2 (AS4/PEEK, Langley Research Center), AS4/8551-7, and AS4/PISO(sub 2)-TPI. For the neat matrix materials, the tensile, shear, fracture toughness, coefficient of thermal expansion, and coefficient of moisture expansion properties were measured as a function of both temperature and moisture content. For the unidirectional composites, axial and transverse tensile, longitudinal shear, coefficient of thermal expansion, and coefficient of moisture expansion properties were determined, at room temperature and 100 C.

Coguill, Scott L.↗
NASA NTRS1981

Problems encountered with conventional fiber-reinforced composites

Preparational, computational, and operational problems associated with fiber-reinforced composites (FRC) are reviewed. Initial preparation of FRCs is shown to involve consideration of the type of prepreg, the setting time, cure conditions and cycles, and cure temperatures. The effects of the choice of bonding agents, the fiber transfer length, and individual fiber responses to bonding agents are noted to have an impact on fiber strength, moisture uptake, and fatigue resistance. The deformation prior to failure and the failure region are modeled through models of mini-, micro- and macro mechanics formulations employing a stiffness matrix, failure criterion, or fracture mechanics. The detection, evaluation, and repair of defects comprises the operational domain, and it is stressed that no good repair techniques exist for FRCs.

Landel, R. F.↗
NASA NTRS1973

Effects of thermal loading on fiber-reinforced composites with constituents of differing thermal expansivities.

Estimates of the magnitudes of elastic stresses and elastoplastic stresses and strains were made for tungsten fiber-reinforced 80Ni + 20Cr matrix composites. Heating or cooling between 80 and 2000 F was assumed. The calculated elastic stresses exceeded representative or estimated strengths of constituents. For composites with less than 0.65 volume fraction of fiber, plastic flow was considered possible, and elastoplastic solutions indicated that stresses would be reduced but with the concomitant occurrence of sufficiently large strain ranges, particularly in the matrix, to pose a possible thermal fatigue problem. Limited experimental studies on tungsten fiber-copper matrix composites heated and cooled a number of times between 80 and 1600 F in a conventional furnace and then heated from 80 to 1652 F in a hot-stage microscope resulted in matrix microfracture for a 70 volume fraction fiber composite and substantial matrix strain for a 40 volue fraction fiber composite.

Hoffman, C. A.↗
NASA NTRS2013

Fiber Reinforced Composite Cores and Panels

A fiber reinforced core panel is formed from strips of plastics foam helically wound with layers of rovings to form webs which may extend in a wave pattern or may intersect transverse webs. Hollow tubes may replace foam strips. Axial rovings cooperate with overlying helically wound rovings to form a beam or a column. Wound roving patterns may vary along strips for structural efficiency. Wound strips may alternate with spaced strips, and spacers between the strips enhance web buckling strength. Continuously wound rovings between spaced strips permit folding to form panels with reinforced edges. Continuously wound strips are helically wrapped to form annular structures, and composite panels may combine both thermoset and thermoplastic resins. Continuously wound strips or strip sections may be continuously fed either longitudinally or laterally into molding apparatus which may receive skin materials to form reinforced composite panels.

Day, Stephen W.↗
NASA NTRS1975

Fundamental analysis of the failure of polymer-based fiber reinforced composites

A mathematical model predicting the strength of unidirectional fiber reinforced composites containing known flaws and with linear elastic-brittle material behavior was developed. The approach was to imbed a local heterogeneous region surrounding the crack tip into an anisotropic elastic continuum. This (1) permits an explicit analysis of the micromechanical processes involved in the fracture, and (2) remains simple enough to be useful in practical computations. Computations for arbitrary flaw size and orientation under arbitrary applied loads were performed. The mechanical properties were those of graphite epoxy. With the rupture properties arbitrarily varied to test the capabilities of the model to reflect real fracture modes, it was shown that fiber breakage, matrix crazing, crack bridging, matrix-fiber debonding, and axial splitting can all occur during a period of (gradually) increasing load prior to catastrophic failure. The calculations also reveal the sequential nature of the stable crack growth process proceding fracture.

Kanninen, M. F.↗
NASA NTRS2005

Toughened Matrix SiC Fiber Reinforced Composites

First matrix cracking stress is a critical parameter for application of Sic fiber reinforced composites in highly stressed, environmentally demanding applications such as turbine blades. High matrix fracture toughness is a key property that contributes to high composite fracture stress. Silicon nitride offers reduced matrix elastic modulus, lower coefficient of thermal expansion, and potentially high fracture toughness compared to Sic matrices. All of these factors can be used to advantage to increase matrix fracture stress. As a first model system we are pursuing toughened silicon nitride matrix composites reinforced with SCS-9 fibers. Fabrication is by tape casting the matrix plies and tape lay-up with fiber plies followed by hot pressing at 1800 C. Progress toward this end will be reported.

Levine, Stanley R.↗
NASA NTRS1990

Matrix toughness, long-term behavior, and damage tolerance of notched graphite fiber-reinforced composite materials

The long-term behavior of notched graphite-fiber-reinforced composite laminates with brittle or tough matrix materials and different fiber architectures was investigated using damage measurements and stiffness change, residual strength, and life data. The fiber/matrix materials included T300/5208, AS4/3501-6, AS4/1808, AS4/PEEK, and C3000/PMR-15 matrices and unidirectional tape and woven cloth fiber architectures. Results of damage evaluation and of residual strength measurements during the fatigue damage development showed that the long-term behavior and damage tolerance are controlled by a number of interacting factors such as the matrix toughness, fiber architecture, loading levels, and damage types and distributions.

Bakis, C. E.↗
NASA NTRS1987

Evaluation of Fiber-Reinforced Composites

Report describes procedures for evaluating properties of advanced fiber-reinforced composite materials. Procedures include quality control, fabrication techniques, specimen machining, test methods, and data collection and interpretation. Applied to specific material: Thornel P-100 carbon fiber combined with Fiberite 934 epoxy resin in form of unidirectional tape.

Clinton, Raymond G., Jr.↗
NASA NTRS1996

Yeh-Stratton Criterion for Stress Concentrations on Fiber-Reinforced Composite Materials

This study investigated the Yeh-Stratton Failure Criterion with the stress concentrations on fiber-reinforced composites materials under tensile stresses. The Yeh-Stratton Failure Criterion was developed from the initial yielding of materials based on macromechanics. To investigate this criterion, the influence of the materials anisotropic properties and far field loading on the composite materials with central hole and normal crack were studied. Special emphasis was placed on defining the crack tip stress fields and their applications. The study of Yeh-Stratton criterion for damage zone stress fields on fiber-reinforced composites under tensile loading was compared with several fracture criteria; Tsai-Wu Theory, Hoffman Theory, Fischer Theory, and Cowin Theory. Theoretical predictions from these criteria are examined using experimental results.

Yeh, Hsien-Yang↗
NASA NTRS1990

Micromechanics analysis of space simulated thermal deformations and stresses in continuous fiber reinforced composites

Space simulated thermally induced deformations and stresses in continuous fiber reinforced composites were investigated with a micromechanics analysis. The investigation focused on two primary areas. First, available explicit expressions for predicting the effective coefficients of thermal expansion (CTEs) for a composite were compared with each other, and with a finite element (FE) analysis, developed specifically for this study. Analytical comparisons were made for a wide range of fiber/matrix systems, and predicted values were compared with experimental data. The second area of investigation focused on the determination of thermally induced stress fields in the individual constituents. Stresses predicted from the FE analysis were compared to those predicted from a closed-form solution to the composite cylinder (CC) model, for two carbon fiber/epoxy composites. A global-local formulation, combining laminated plate theory and FE analysis, was used to determine the stresses in multidirectional laminates. Thermally induced damage initiation predictions were also made.

Bowles, David E.↗
NASA NTRS1980

Three dimensional finite element analysis of layered fiber-reinforced composite materials

A three-dimensional finite element analysis was performed for a biaxially loaded composite laminate (with a centered hole) consisting of several fiber-reinforced composite layers each with a specified fiber orientation. The detailed stress distribution around the hole was determined. Also, the locations of initial damage zones due to different failure mechanisms were indicated.

Lee, J. D.↗