Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “electrode stacks”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 397 records · Page 22

Particle size effect in porous film electrodes of ligand-modified graphene for enhanced supercapacitor performance

Graphene-based electrodes for high performance supercapacitors are developed by taking advantage of particle size control, large mass loading, and surface functionalization of reduced graphene oxide (rGO) sheets. Two controlled sizes of graphene sheets (100 nm vs. 45 μm average lateral dimensions) were prepared to study two-electrode system performance. The nano-size graphenes led to the formation of mesoporous films, resulting in higher capacitance, better capacitance retension and lower equivalent series resistance (ESR), indicating better surface usability for diffusion and accessibility of electrolyte ions by shortening transport paths (compared with horizontally stacked films from micro-sized graphenes). For studies using an aqueous electrolyte, the maximum specific capacitance of nano-rGO film was 302 F/g (at 1 A/g with 4.3 mg/cm 2 of mass loading), which was ~2.4 times higher than micro-rGO film, and achieved a ~67% reduced ESR. With an organic electrolyte, the nano-rGO delivered ~4.2 times higher capacitance (115 F/g at 2 A/g with 4.3 mg/cm 2 ), 4.0 times lower IR drops, and an order-of-magnitude lower charge-transfer resistance with an energy density of 18.7 Wh/kg. Finally, the results of this work indicate that the size control of graphene sheet particles for film deposit electrodes can be a simple but effective approach to improve supercapacitor performance.

36 MATERIALS SCIENCE↗

Cummins R-SOFC System Development

The overall purpose of this project was to reduce the Reversible-Solid Oxide Fuel Cell (R-SOFC) system cost by developing two technologies, an improved cell design and the incorporation of an ejector in the fuel recycle loop instead of a blower. A Simulink model of the baseline SOFC system was developed and calibrated with experimental test data. The R-SOFC system model was built by integrating GT Suite developed models of the steam generation components into the baseline Simulink SOFC system model. The ability to run the stack in SOEC operating mode was also added to the model. The system model was used to explore the ability of the R-SOFC system to meet operational constraints on Steam/Carbon ratio and H2 concentration on the fuel side electrode. A CFD ejector model was developed and used to explore a range of ejector design parameters, leading to the final ejector design that was prototyped for testing. A prototype steam ejector was first tested in a laboratory environment using room temperature air. The steam ejector was subsequently tested using the full hot recycle loop with all relevant heat exchangers and steam generation components. The test conditions utilized temperatures, pressures, and flow rates expected in an R-SOFC application. Throughout the experimental testing work, ejector performance test data was used to improve and then validate the CFD ejector model. A CFD cell model was developed and used to optimize thermal gradients, voltage, and cost of a new cell substrate design. A CFD comparison of co-flow and cross-flow cell designs informed the decision to use a co-flow design for the new cell substrate. Multiple rounds of CFD simulation were used to improve the cell design to minimize the variation in air and fuel distribution across cell channels and to minimize the variation in air and fuel distribution across different cells in the stack. A few prototypes of the new cell substrate design were produced and validated in a laboratory environment by thermally spraying and verifying that they met established manufacturing specifications. The cell manufacturing process was adjusted in order to bring these metrics within acceptable tolerances. Cummins’ internal calculations show that the new cell design reduces cost ~50% compared to the baseline cell, while the ejector + superheater/boiler concept reduces cost of the recycle loop by ~40%. The impact of these cost reductions on the cost of producing H2 will depend on the specific system where they are applied. Therefore, a Techno-Economic Analysis was completed using system cost as a variable, and showing how the NREL Current and Future system costs translate into H2 production cost.

Henrichsen, Lars↗

Electroslag additive manufacturing: A pathway for high throughput near net shape production

Electroslag Additive Manufacturing (ESAM), a new high-throughput additive manufacturing (AM) method that combines Electroslag Strip Cladding (ESC) and wire arc AM (WAAM) is introduced. This combination enables the high deposition rate of ESC (more than 20 kg/h with a 60 mm strip electrode) to benefit from the precise geometric control of WAAM. As a precursor to ESAM, the ESC process is investigated in an AM context independently by evaluating both direct and staggered bead-stacking strategies and analyzing the microstructural and mechanical properties of each. This is followed by an ESAM demonstration producing an annular geometry by pairing ESC with gas tungsten arc welding (GTAW), wherein GTAW is utilized to construct annular walls that are subsequently infilled via ESC. The microstructure and mechanical properties of ESC-only AM are compared with that of the ESAM method and it is shown that printed integral retaining walls do not impact the resulting mechanical properties of ESAM. Furthermore, results indicate that ESAM-produced Alloy 625 parts exhibit tensile properties on par with cast counterparts, supporting the method’s scalability to components exceeding one metric ton, and possibly making ESAM a viable future manufacturing approach for competitive production of large-scale components currently manufactured by casting and forging.

Additive manufacturing↗

Modulation of interlayer exchange coupling strength in magnetic tunnel junctions via strain effect

Interlayer exchange coupling of two ferromagnetic electrodes separated by a thin MgO tunnel barrier is investigated using magneto-optical Kerr effect. We find that the coupling field can be reduced by more than 40% as the thickness of a top Ta capping layer increases from 0.5 to 1.2 nm. In contrast, a similar film stack with an additional 3 nm Ru capping layer displays no such dependence on Ta thickness. Transmission electron microscopy study shows that the oxidation of the exposed Ta capping layer induces changes in the crystalline structures of the underlying films, giving rise to the observed reduction of the interlayer coupling field.

36 MATERIALS SCIENCE↗

A High Temperature Electrochemical Energy Storage System Based on Sodium Beta-Alumina Solid Electrolyte (Base)

This report summarizes the work done during the period September 1, 2005 and March 31, 2008. Work was conducted in the following areas: (1) Fabrication of sodium beta{double_prime} alumina solid electrolyte (BASE) using a vapor phase process. (2) Mechanistic studies on the conversion of {alpha}-alumina + zirconia into beta{double_prime}-alumina + zirconia by the vapor phase process. (3) Characterization of BASE by X-ray diffraction, SEM, and conductivity measurements. (4) Design, construction and electrochemical testing of a symmetric cell containing BASE as the electrolyte and NaCl + ZnCl{sub 2} as the electrodes. (5) Design, construction, and electrochemical evaluation of Na/BASE/ZnCl{sub 2} electrochemical cells. (6) Stability studies in ZnCl{sub 2}, SnCl{sub 2}, and SnI{sub 4} (7) Design, assembly and testing of planar stacks. (8) Investigation of the effect of porous surface layers on BASE on cell resistance. The conventional process for the fabrication of sodium ion conducting beta{double_prime}-alumina involves calcination of {alpha}-alumina + Na{sub 2}CO{sub 3} + LiNO{sub 3} at 1250 C, followed by sintering powder compacts in sealed containers (platinum or MgO) at {approx}1600 C. The novel vapor phase process involves first sintering a mixture of {alpha}-alumina + yttria-stabilized zirconia (YSZ) into a dense ceramic followed by exposure to soda vapor at {approx}1450 C to convert {alpha}-alumina into beta{double_prime}-alumina. The vapor phase process leads to a high strength BASE, which is also resistant to moisture attack, unlike BASE made by the conventional process. The PI is the lead inventor of the process. Discs and tubes of BASE were fabricated in the present work. In the conventional process, sintering of BASE is accomplished by a transient liquid phase mechanism wherein the liquid phase contains NaAlO{sub 2}. Some NaAlO{sub 2} continues to remain at grain boundaries; and is the root cause of its water sensitivity. In the vapor phase process, NaAlO{sub 2} is never formed. Conversion occurs by a coupled transport of Na{sup +} through BASE formed and of O{sup 2-} through YSZ to the reaction front. Transport to the reaction front is described in terms of a chemical diffusion coefficient of Na{sub 2}O. The conversion kinetics as a function of microstructure is under investigation. The mechanism of conversion is described in this report. A number of discs and tubes of BASE have been fabricated by the vapor phase process. The material was investigated by X-ray diffraction (XRD), optical microscopy and scanning electron microscopy (SEM), before and after conversion. Conductivity (which is almost exclusively due to sodium ion transport at the temperatures of interest) was measured. Conductivity was measured using sodium-sodium tests as well as by impedance spectroscopy. Various types of both planar and tubular electrochemical cells were assembled and tested. In some cases the objective was to determine if there was any interaction between the salt and BASE. The interaction of interest was mainly ion exchange (possible replacement of sodium ion by the salt cation). It was noted that Zn{sup 2+} did not replace Na+ over the conditions of interest. For this reason much of the work was conducted with ZnCl{sub 2} as the cathode salt. In the case of Sn-based, Sn{sup 2+} did ion exchange, but Sn{sup 4+} did not. This suggests that Sn{sup 4+} salts are viable candidates. These results and implications are discussed in the report. Cells made with Na as the anode and ZnCl{sub 2} as the cathode were successfully charged/discharged numerous times. The key advantages of the batteries under investigation here over the Na-S batteries are: (1) Steel wool can be used in the cathode compartment unlike Na-S batteries which require expensive graphite. (2) Planar cells can be constructed in addition to tubular, allowing for greater design flexibility and integration with other devices such as planar SOFC. (3) Comparable or higher open circuit voltage (OCV) than the Na-S battery. (4) Wider operating temperature range and higher temperature operation than the Na-S battery. (5) If a cell fails, it fails in the short circuit mode unlike Na-S batteries. Also, cells were successfully subjected to several freeze-thaw cycles. Finally, the feasibility of assembling a planar stack was explored. A two cell stack was assembled and tested. A five cell stack was assembled.

25 ENERGY STORAGE↗

Matrix-assisted energy conversion in nanostructured piezoelectric arrays

A nanoconverter is capable of directly generating electricity through a nanostructure embedded in a polymer layer experiencing differential thermal expansion in a stress transfer zone. High surface-to-volume ratio semiconductor nanowires or nanotubes (such as ZnO, silicon, carbon, etc.) are grown either aligned or substantially vertically aligned on a substrate. The resulting nanoforest is then embedded with the polymer layer, which transfers stress to the nanostructures in the stress transfer zone, thereby creating a nanostructure voltage output due to the piezoelectric effect acting on the nanostructure. Electrodes attached at both ends of the nanostructures generate output power at densities of .about.20 nW/cm.sup.2 with heating temperatures of .about.65.degree. C. Nanoconverters arrayed in a series parallel arrangement may be constructed in planar, stacked, or rolled arrays to supply power to nano- and micro-devices without use of external batteries.

30 DIRECT ENERGY CONVERSION↗

Electrochemistry at Back-Gated, Ultrathin ZnO Electrodes: Field-Effect Modulation of Heterogeneous Electron Transfer Rate Constants by 30× with Enhanced Gate Capacitance

We report steady-state voltammetry of outer-sphere redox species at back-gated ultrathin ZnO working electrodes in order to determine electron transfer rate constants k ET as a function of independently-controlled gate bias, V G . We demonstrate that k ET can be modulated as much as 30-fold by application of V G ≤ 8 V. Key to this demonstration was integrating the ultrathin (5 nm) ZnO on a high dielectric constant (k) insulator, HfO 2 (30 nm), which was grown on a Pd metal gate. The high-k HfO 2 dramatically decreased the required V G values and increased the gate-induced charge in ZnO compared to previous studies. Importantly, the enhanced gating power of the Pd/HfO 2 /ZnO stack meant it was possible to observe a non-monotonic dependence of k ET on V G , which reflects the inherent density of redox acceptor states in solution. Furthermore, this work adds to the growing body of literature demonstrating that electrochemical kinetics (i.e., rate constants and overpotentials) at ultrathin working electrodes can be tuned by V G , independent of the conventional electrochemical working electrode potential.

36 MATERIALS SCIENCE↗

Measurement of Small Molecular Dopant F4TCNQ and C 60 F 36 Diffusion in Organic Bilayer Architectures

The diffusion of molecules through and between organic layers is a serious stability concern in organic electronic devices. In this paper, the temperature-dependent diffusion of molecular dopants through small molecule hole transport layers is observed. Specifically we investigate bilayer stacks of small molecules used for hole transport (MeO-TPD) and p-type dopants (F4TCNQ and C 60 F 36 ) used in hole injection layers for organic light emitting diodes and hole collection electrodes for organic photovoltaics. With the use of absorbance spectroscopy, photoluminescence spectroscopy, neutron reflectometry, and near-edge X-ray absorption fine structure spectroscopy, we are able to obtain a comprehensive picture of the diffusion of fluorinated small molecules through MeO-TPD layers. F4TCNQ spontaneously diffuses into the MeO-TPD material even at room temperature, while C 60 F 36 , a much bulkier molecule, is shown to have a substantially higher morphological stability. Finally, this study highlights that the differences in size/geometry and thermal properties of small molecular dopants can have a significant impact on their diffusion in organic device architectures.

36 MATERIALS SCIENCE↗

Influence of PEDOT:PSS on the effectiveness of barrier layers prepared by atomic layer deposition in organic light emitting diodes

Organic light emitting diodes (OLEDs) are well suited for energy saving lighting applications, especially when thinking about highly flexible and large area devices. In order to avoid the degradation of the organic components by water and oxygen, OLEDs need to be encapsulated, e.g., by a thin sheet of glass. As the device is then no longer flexible, alternative coatings are required. Atomic layer deposition (ALD) is a very promising approach in this respect. The authors studied OLEDs that were encapsulated by 100 nm Al{sub 2}O{sub 3} deposited by ALD. The authors show that this coating effectively protects the active surface area of the OLEDs from humidity. However, secondary degradation processes still occur at sharp edges of the OLED stack where the extremely thin encapsulation layer does not provide perfect coverage. Particularly, the swelling of poly(3,4-ethylenedioxythiophene) mixed with poly(styrenesulfonate), which is a popular choice for the planarization of the bottom electrode and at the same time acts as a hole injection layer, affects the effectiveness of the encapsulation layer.

36 MATERIALS SCIENCE↗

Planar electrochemical device assembly

A pre-fabricated electrochemical device having a dense electrolyte disposed between an anode and a cathode preferably deposited as thin films is bonded to a porous electrically conductive support. A second porous electrically conductive support may be bonded to a counter electrode of the electrochemical device. Multiple electrochemical devices may be bonded in parallel to a single porous support, such as a perforated sheet to provide a planar array. Planar arrays may be arranged in a stacked interconnected array. A method of making a supported electrochemical device is disclosed wherein the method includes a step of bonding a pre-fabricated electrochemical device layer to an existing porous metal or porous metal alloy layer.

Jacobson, Craig P.↗

Achieving 5,000-h and 8,000-h Low-PGM Electrode Durability on Automotive Drive Cycles

Whereas total Pt loading in anode and cathode catalysts below 0.125 mg cm −2 is required to meet the stringent cost target for automotive fuel cell systems (FCS) for light duty vehicles, low-loaded cathode catalysts are susceptible to unacceptable aging-related performance losses at high current densities. A framework model, validated by accelerated stress test data, has identified cell voltage, relative humidity (RH) and temperature as the key operating variables that affect degradation of a high-activity d-PtCo/C cathode catalyst with 0.1 mg cm −2 Pt loading. Drive cycle simulations indicate that these can be controlled by properly selecting the minimum FCS power, compressor-expander module (CEM) turndown, and stack coolant temperature. The optimum system parameters are 4-kW e minimum power for an 80-kW e FCS, CEM turndown of 12.5, and 66 °C average coolant exit temperature that combine to limit the maximum cell voltage to 850 mV and outlet RH to 90%–100%. Depending on Pt loading, the mismatch between actual and allowable degradation for 10% power loss over 5,000-h lifetime requires the stack to be oversized by 2.4%–5%, resulting in 8.4%–41% lower Pt utilization and 7.1%–20.5% penalty in stack cost. The corresponding results for 8,000-h lifetime are 10.3%-14% stack oversizing, 23%–51.8% lower Pt utilization, and 24.1%–35.4% stack cost penalty.

08 HYDROGEN↗

Wide Band Gap Chalcopyrite Photoelectrodes for Direct Water Splitting (Final Technical Report)

The chalcopyrite material class, typically identified by its most popular alloy CuInGaSe 2 , provides exceptionally good candidates for photoelectrochemical (PEC) water splitting and has the potential to meet DoE EERE’s targets in terms of hydrogen production costs (less than $2/gge). Some key advantages of this class include remarkable photon-to-electron conversion efficiency and a high Faradaic efficiency for the hydrogen evolution reaction, two characteristics essential for efficient PEC water splitting. However, the band gaps of commonly used chalcopyrites in the photovoltaic field (1.0-1.6 eV) are too narrow to be compatible with the multi-junction approach for efficient PEC hydrogen production, in which a stack of solar absorbers generates the bias required for water splitting. Nonetheless, previous studies performed by our team demonstrated that chalcopyrites’ narrow band gaps could be effectively widened using simple conversion steps, leading to functional chalcopyrite-based PEC electrodes with optical band gap in the 1.8-2.4 eV range, making this class highly suitable for renewable hydrogen production via water splitting. This multi-disciplinary research program lead by the University of Hawai’i/Hawai’i Natural Energy Institute combined unique analytical techniques (UNLV), state-of-the-art theoretical modeling (LLNL) with advanced thin film materials synthesis (HNEI, NREL and Stanford) to provide deeper understanding of wide band gap chalcopyrite-based PEC materials and engineer high performance/corrosion-resistant photocathodes with tunable energetics and compatible with the multi-junction approach. The goals of this project were to demonstrate photoelectrochemical (PEC) solar-hydrogen production using a dual absorber system with a solar-to-hydrogen conversion efficiency of at least 15% with an operational life up to 2,000 hours and capable of generating at least 3 liters of hydrogen in 8 hours. After a brief introduction (Section 1) and description of our work plan (Section 2), we present in Section 3 our results on the development of new wide bandgap copper chalcopyrites absorbers for PEC waters splitting. We first show through modeling how alloying can be used to tailor the optical properties and/or surface energetics of various material candidates. We also present how specific defects (e.g., GaCu) can lead to recombination centers within the forbidden gap of copper-poor chalcopyrites. Then, we present our efforts to synthesize high efficiency wide band gap CuGa 3 Se 5 , CuGa(S,Se) 2 and Cu(In,Ga)S 2 photocathodes capable of generating photocurrent density over 10 mA/cm 2 . We also demonstrate that Cu-rich absorbers should be avoided as they lead to poor sub-band gap optical transmission. In Section 4, we first report on our efforts to tune the energetics of chalcopyrites toward the hydrogen evolution reaction. First, we quantified the energetics of wide band gap chalcopyrites interfaced with conventional CdS buffer layer, as measured with X-ray photoelectron spectroscopy techniques, and evidence the presence of a large (and undesirable) conduction band offset at this interface. Then, we highlight some of the work performed with alternative buffer layers, including In 2 S 3 . Durability improvements with various ultra-thin protective layers are presented in Section 5. Our data show that TiO 2 combined with MoS 2 can significantly improve chalcopyrites lifetime up to 350 hours under continuous operation at 8 mA/cm 2 . Finally, in Section 6 we report strategies to integrate chalcopyrite photocathodes into standalone tandem PEC devices. Although promising methods were proposed for both mechanical and monolithic stacking with narrow band gap PV drivers, no functional device was fabricated on time to fulfill the program end goals.

08 HYDROGEN↗

Durability Evaluation of Reversible Solid Oxide Cells

An experimental investigation on the performance and durability of single solid oxide cells (SOCs) is under way at the Idaho National Laboratory. Reversible operation of SOCs includes electricity generation in the fuel cell mode and hydrogen generation in the electrolysis mode. Degradation is a more significant issue when operating SOCs in the electrolysis mode. In order to understand and mitigate the degradation issues in high temperature electrolysis, single SOCs with different configurations from several manufacturers have been evaluated for initial performance and long-term durability. A new test apparatus for single cell and small stack tests has been developed for this purpose. Cells were obtained from four industrial partners. Cells from Ceramatec Inc. and Materials and Systems Research Inc. (MSRI) showed improved durability in electrolysis mode compared to previous stack tests. Cells from Saint Gobain Advanced Materials Inc. (St. Gobain) and SOFCPower Inc. demonstrated stable performance in the fuel cell mode, but rapid degradation in the electrolysis mode, especially at high current density. Electrolyte-electrode delamination was found to have a significant impact on degradation in some cases. Enhanced bonding between electrolyte and electrode and modification of the electrode microstructure helped to mitigate degradation. Polarization scans and AC impedance measurements were performed during the tests to characterize cell performance and degradation.

08 HYDROGEN↗

Flow simulation and analysis of high-power flow batteries

The cost of a flow battery system can be reduced by increasing its power density and thereby reducing its stack area. If per-pass utilizations are held constant, higher battery power densities can only be achieved using higher flow rates. Here, a 3D computational fluid dynamics model of a flow battery flow field and electrode is used to analyze the implications of increasing flow rates to high power density operating conditions. Interdigitated and serpentine designs, and cell sizes ranging from 10 cm 2 to 400 cm 2 , are simulated. The results quantify the dependence of pressure loss on cell size and design, demonstrating that the details of the passages that distribute flow between individual channels and the inlet and outlet have a major impact on pressure losses in larger cells. Additionally, in-cell flow behavior is analyzed as a function of cell size and design. Flow structures are interrogated to show how and where electrode parameters influence pressure drops, and how regions where transport is slow are correlated with the presence of experimentally observed cell degradation.

25 ENERGY STORAGE↗

In Situ Formation of Polycyclic Aromatic Hydrocarbons as an Artificial Hybrid Layer for Lithium Metal Anodes

Nonuniform Li deposition causes dendrites and low Coulombic efficiency (CE), seriously hindering the practical applications of Li metal. Herein, we developed an artificial solid-state interphase (SEI) with planar polycyclic aromatic hydrocarbons (PAHs) on the surface of Li metal anodes by a facile in situ formation technology. The resultant dihydroxyviolanthron (DHV) layers serve as the protective layer to stabilize the SEI. In addition, the oxygen-containing functional groups in the soft and conformal SEI film can regulate the diffusion and transport of Li ions to homogenize the deposition of Li metal. The artificial SEI significantly improves the CEs and shows superior cyclability of over 1000 h at 4 mAh cm –2 . The LiFePO 4 /Li cell (2.8 mAh cm –2 ) enables a long cyclability for 300 cycles and high CEs of 99.8%. Furthermore, this work offers a new strategy to inhibit Li dendrite growth and enlightens the design on stable SEI for metal anodes.

25 ENERGY STORAGE↗

Durability of Metallic Interconnects and Protective Coatings

To build up a useful voltage, a number of solid oxide fuel cells (SOFCs) are electrically connected into series in a stack via interconnects, which are placed between adjacent cells. In addition to functioning as a bi-polar electrical connector, the interconnect also acts as a separator plate that separates the fuel at the anode side of one cell from the air at the cathode side on an adjacent cell. During SOFC operation at the high temperatures, the interconnects are thus simultaneously exposed to the oxidizing air at one side and a reducing fuel that can be either hydrogen or hydrocarbon at the other. Besides, they are in contact with adjacent components, such as electrodes or electrical contacts, seals, etc. With steady reduction in SOFC operating temperatures into the low or intermediate range 600-850oC, oxidation resistant alloys are often used to construct interconnects. However, the metallic interconnects may degrade via interactions at their interfaces with surrounding environments or adjacent components, potentially affecting the stability and performance of interconnects and the SOFC stacks. Thus protection layers are applied to metallic interconnects that also intend to mitigate or prevent chromium migration into cells and the cell poisoning. This chapter provides a comprehensive review of materials for metallic interconnects, their degradation and coating protection.

solid oxide fuel cell, interconnect, oxidation, co↗