Results for “dynamic load model” — Page 22

NASA NTRS1993

Effect of extended tooth contact on the modeling of spur gear transmissions

In some gear dynamic models, the effect of tooth flexibility is ignored when the model determines which pairs of teeth are in contact. Deflection of loaded teeth is not introduced until the equations of motion are solved. This means the zone of tooth contact and average tooth meshing stiffness are underestimated and the individual tooth load is overstated, especially for heavily-loaded gears. The static transmission error and dynamic load of heavily-loaded, low-contact-ratio spur gears is compared with this effect both neglected and included. Neglecting the effect yields an underestimate of resonance speeds and an overestimate of the dynamic load.

Oswald, Fred B.↗

NASA NTRS1993

Effect of extended tooth contact on the modeling of spur gear transmissions

In some gear dynamic models, the effect of tooth flexibility is ignored when the model determines which pairs of teeth are in contact. Deflection of loaded teeth is not introduced until the equations of motion are solved. This means the zone of tooth contact and average tooth meshing stiffness are underestimated and the individual tooth load is overstated, especially for heavily-loaded gears. The static transmission error and dynamic load of heavily-loaded, low-contact-ratio spur gears is compared with this effect both neglected and included. Neglecting the effect yields an underestimate of resonance speeds and an overestimate of the dynamic load.

Lin, Hsiang H.↗

NASA NTRS1998

PLUM: Parallel Load Balancing for Adaptive Unstructured Meshes

Mesh adaption is a powerful tool for efficient unstructured-grid computations but causes load imbalance among processors on a parallel machine. We present a novel method called PLUM to dynamically balance the processor workloads with a global view. This paper presents the implementation and integration of all major components within our dynamic load balancing strategy for adaptive grid calculations. Mesh adaption, repartitioning, processor assignment, and remapping are critical components of the framework that must be accomplished rapidly and efficiently so as not to cause a significant overhead to the numerical simulation. A data redistribution model is also presented that predicts the remapping cost on the SP2. This model is required to determine whether the gain from a balanced workload distribution offsets the cost of data movement. Results presented in this paper demonstrate that PLUM is an effective dynamic load balancing strategy which remains viable on a large number of processors.

Oliker, Leonid↗

NASA NTRS2005

Multiscale Modeling for the Analysis for Grain-Scale Fracture Within Aluminum Microstructures

Multiscale modeling methods for the analysis of metallic microstructures are discussed. Both molecular dynamics and the finite element method are used to analyze crack propagation and stress distribution in a nanoscale aluminum bicrystal model subjected to hydrostatic loading. Quantitative similarity is observed between the results from the two very different analysis methods. A bilinear traction-displacement relationship that may be embedded into cohesive zone finite elements is extracted from the nanoscale molecular dynamics results.

Glaessgen, Edward H.↗

NASA NTRS1997

The Benchmark Active Controls Technology Model Aerodynamic Data

The Benchmark Active Controls Technology (BACT) model is a part of the Benchmark Models Program (BMP). The BMP is a NASA Langley Research Center program that includes a series of models which were used to study different aeroelastic phenomena and to validate computational fluid dynamics codes. The primary objective of BACT testing was to obtain steady and unsteady loads, accelerations, and aerodynamic pressures due to control surface activity in order to calibrate unsteady CFD codes and active control design tools. Three wind-tunnel tests in the Transonic Dynamics Tunnel (TDT) have been completed. The first and parts of the second and third tests focused on collecting open-loop data to define the model's aeroservoelastic characteristics, including the flutter boundary across the Mach range. It is this data that is being presented in this paper. An extensive database of over 3000 data sets was obtained. This database includes steady and unsteady control surface effectiveness data, including pressure distributions, control surface hinge moments, and overall model loads due to deflections of a trailing edge control surface and upper and lower surface

Scott, Robert C.↗

NASA NTRS1987

The dynamic aspects of thermo-elasto-viscoplastic snap-through and creep buckling phenomena

Use of a mathematical model and solution methodology, to examine dynamic buckling and dynamic postbuckling behavior of shallow arches and spherical caps made of a realistic material and undergoing non-isothermal, elasto-viscoplastic deformation was examined. Thus, geometric as well as material type nonlinearities of higher order are included in this analysis. The dynamic stability problem is studied under impulsive loading and suddenly applied loading with loads of constant magnitude and infinite duration. A finite element model was derived directly from the incrementally formulated nonlinear shell equations, by using a tensor-oriented procedure. As an example of the results, the time history of the midspan displacement of a damped shallow circular arch is presented.

Riff, R.↗

NASA NTRS1989

Application of attachment modes in the control of large space structures

Various ways are examined to obtain reduced order mathematical models of structures for use in dynamic response analyses and in controller design studies. Attachment modes are deflection shapes of a structure subjected to specified unit load distributions. Attachment modes are frequently employed to supplement free-interface normal modes to improve the modeling of components (structures) employed in component mode synthesis analyses. Deflection shapes of structures subjected to generalized loads of some specified distribution and of unit magnitude can also be considered to be attachment modes. Several papers which were written under this contract are summarized herein.

Craig, Roy R., Jr.↗

NASA NTRS2023

A Hybrid Transfer Function Procedure for Broadband Auralization Within Small Flight Vehicle Interiors

Auralization of the sound fields within flight vehicle interiors is of interest to aircraft designers considering crew and passenger ride quality. Computer models can be used to predict the filtering effects that the fuselage structure and interior volume have on the exterior sound field in order to simulate the resulting cabin interior noise. However, this can become expensive when a wide frequency range of analysis suitable for passenger auralization is desired. This is particularly the case when using deterministic modeling methods such as finite element analysis (FEA) wherein prohibitively high levels of detail and finite element discretizations are required to resolve the wavelengths at high frequencies. On the contrary, Statistical Energy Analysis (SEA), while not capturing important modal behaviors at low frequencies, is better suited for higher frequency analyses where structural and interior dynamics exhibit high modal overlap and spatially averaged physical quantities suffice. For this reason, a hybrid procedure is considered here that utilizes FE modal solutions at lower frequencies and SEA results at higher frequencies. A transfer function dataset containing the exterior to interior vibroacoustic filtering effect is calculated accordingly and subsequently stored to be used for a variety of exterior dynamic load cases. At low frequencies, the transfer function dataset detail is related to the level of FE model refinement whereas at high frequencies it functions as an equalizer array with a level of detail corresponding to the SEA subsystem partitioning scheme. The above procedure is described herein and demonstrated on a six passenger flight vehicle with eight propulsors in a hover flight condition.

auralization↗

NASA NTRS2023

A Hybrid Transfer Function Procedure for Broadband Auralization Within Small Flight Vehicle Interiors

Auralization of the sound fields within flight vehicle interiors is of interest to aircraft designers considering crew and passenger ride quality. Computer models can be used to predict the filtering effects that the fuselage structure and interior volume have on the exterior sound field in order to simulate the resulting cabin interior noise. However, this can become expensive when a wide frequency range of analysis suitable for passenger auralization is desired. This is particularly the case when using deterministic modeling methods such as finite element analysis (FEA) wherein prohibitively high levels of detail and finite element discretizations are required to resolve the wavelengths at high frequencies. On the contrary, Statistical Energy Analysis (SEA), while not capturing important modal behaviors at low frequencies, is better suited for higher frequency analyses where structural and interior dynamics exhibit high modal overlap and spatially averaged physical quantities suffice. For this reason, a hybrid procedure is considered here that utilizes FE modal solutions at lower frequencies and SEA results at higher frequencies. A transfer function dataset containing the exterior to interior vibroacoustic filtering effect is calculated accordingly and subsequently stored to be used for a variety of exterior dynamic load cases. At low frequencies, the transfer function dataset detail is related to the level of FE model refinement whereas at high frequencies it functions as an equalizer array with a level of detail corresponding to the SEA subsystem partitioning scheme. The above procedure is described herein and demonstrated on a six passenger flight vehicle with eight propulsors in a hover flight condition.

auralization↗

NASA NTRS2006

Flight Test of an Adaptive Controller and Simulated Failure/Damage on the NASA NF-15B

The method of flight-testing the Intelligent Flight Control System (IFCS) Second Generation (Gen-2) project on the NASA NF-15B is herein described. The Gen-2 project objective includes flight-testing a dynamic inversion controller augmented by a direct adaptive neural network to demonstrate performance improvements in the presence of simulated failure/damage. The Gen-2 objectives as implemented on the NASA NF-15B created challenges for software design, structural loading limitations, and flight test operations. Simulated failure/damage is introduced by modifying control surface commands, therefore requiring structural loads measurements. Flight-testing began with the validation of a structural loads model. Flight-testing of the Gen-2 controller continued, using test maneuvers designed in a sequenced approach. Success would clear the new controller with respect to dynamic response, simulated failure/damage, and with adaptation on and off. A handling qualities evaluation was conducted on the capability of the Gen-2 controller to restore aircraft response in the presence of a simulated failure/damage. Control room monitoring of loads sensors, flight dynamics, and controller adaptation, in addition to postflight data comparison to the simulation, ensured a safe methodology of buildup testing. Flight-testing continued without major incident to accomplish the project objectives, successfully uncovering strengths and weaknesses of the Gen-2 control approach in flight.

Buschbacher, Mark↗

NASA NTRS2022

Using Soil Moisture Information to Better Understand and Predict Wildfire Danger: A Review of Recent Developments and Outstanding Questions

Soil moisture conditions are represented in fire danger rating systems mainly through simple drought indices based on meteorological variables, even though better sources of soil moisture information are increasingly available. This review summarises a growing body of evidence indicating that greater use of in situ, remotely sensed, and modelled soil moisture information in fire danger rating systems could lead to better estimates of dynamic live and dead herbaceous fuel loads, more accurate live and dead fuel moisture predictions, earlier warning of wildfire danger, and better forecasts of wildfire occurrence and size. Potential uses of soil moisture information in existing wildfire danger rating systems include (1) as a supplement or replacement for drought indices, (2) for live and (3) dead fuel moisture modelling, (4) for estimating herbaceous fuel curing, and (5) for estimating fuel loads. We identify key remaining research questions and note the logistical challenge of convincing wildfire professionals of the importance of soil moisture compared with more familiar wildfire danger metrics. While obstacles remain, the path forward is clear. Soil moisture information can and should be used to improve fire danger rating systems and contribute to more effective fire management for the protection of communities and ecosystems worldwide.

fuel properties↗

NASA NTRS2011

On Calculation Methods and Results for Straight Cylindrical Roller Bearing Deflection, Stiffness, and Stress

The purpose of this study was to assess some calculation methods for quantifying the relationships of bearing geometry, material properties, load, deflection, stiffness, and stress. The scope of the work was limited to two-dimensional modeling of straight cylindrical roller bearings. Preparations for studies of dynamic response of bearings with damaged surfaces motivated this work. Studies were selected to exercise and build confidence in the numerical tools. Three calculation methods were used in this work. Two of the methods were numerical solutions of the Hertz contact approach. The third method used was a combined finite element surface integral method. Example calculations were done for a single roller loaded between an inner and outer raceway for code verification. Next, a bearing with 13 rollers and all-steel construction was used as an example to do additional code verification, including an assessment of the leading order of accuracy of the finite element and surface integral method. Results from that study show that the method is at least first-order accurate. Those results also show that the contact grid refinement has a more significant influence on precision as compared to the finite element grid refinement. To explore the influence of material properties, the 13-roller bearing was modeled as made from Nitinol 60, a material with very different properties from steel and showing some potential for bearing applications. The codes were exercised to compare contact areas and stress levels for steel and Nitinol 60 bearings operating at equivalent power density. As a step toward modeling the dynamic response of bearings having surface damage, static analyses were completed to simulate a bearing with a spall or similar damage.

Krantz, Timothy L.↗

NASA NTRS2006

Aerodynamics of Trans-Atmospheric Vehicles: A Non-Dimensional Approach

A novel non-dimensional approach to flight dynamics of a trans-atmospheric vehicle is proposed. This approach explicitly takes into account the vertical span of the atmosphere (atmospheric scale height) as well as atmospheric mass load (atmospheric pressure) at the given flight level. As an example of application of this approach, a simple analytic model of the flight dynamics is considered for the powered boost and non-powered glide of a trans-atmospheric vehicle.

planetary spacecraft↗

NASA NTRS1971

Analytical studies of nuclear light bulb engine radiant heat transfer and performance characteristics

Analytical model of nuclear light bulb engine radiant heat transfer and engine performance, dynamics and control, heat loads and shutdown characteristics

Rodgers, R. J.↗

NASA NTRS1975

Finite element analysis using NASTRAN applied to helicopter transmission vibration/noise reduction

A finite element NASTRAN model of the complete forward rotor transmission housing for the Boeing Vertol CH-47 helicopter was developed and applied to reduce transmission vibration/noise at its source. In addition to a description of the model, a technique for vibration/noise prediction and reduction is outlined. Also included are the dynamic response as predicted by NASTRAN, test data, the use of strain energy methods to optimize the housing for minimum vibration/noise, and determination of design modifications which will be manufactured and tested. The techniques presented are not restricted to helicopters but are applicable to any power transmission system. The transmission housing model developed can be used further to evaluate static and dynamic stresses, thermal distortions, deflections and load paths, fail-safety/vulnerability, and composite materials.

Howells, R. W.↗

NASA NTRS1976

Roller bearing geometry design

A theory of kinematic stabilization of rolling cylinders is extended and applied to the design of cylindrical roller bearings. The kinematic stabilization mechanism puts a reverse skew into the rolling elements by changing the roller taper. Twelve basic bearing modification designs are identified amd modeled. Four have single transverse convex curvature in their rollers while eight have rollers which have compound transverse curvature made up of a central cylindrical band surrounded by symmetric bands with slope and transverse curvature. The bearing designs are modeled for restoring torque per unit axial displacement, contact stress capacity, and contact area including dynamic loading, misalignment sensitivity and roller proportion. Design programs are available which size the single transverse curvature roller designs for a series of roller slopes and load separations and which design the compound roller bearings for a series of slopes and transverse radii of curvature. The compound rollers are proportioned to have equal contact stresses and minimum size. Design examples are also given.

Savage, M.↗

NASA NTRS1978

The viscoelastic stiffness model of seismicity

A viscoelastic stiffness model of seismicity is developed by introducing a viscoelastic element into the stiffness model for fault dynamics. The introduction of this element permits modeling of transient anelastic deformations in response to stress loading and relaxation and provides a mechanism for partial stress recovery following an earthquake. As a consequence, several phenomena not present in elastic stiffness theory emerge. These include postseismic creep, foreshocks, and aftershocks. Numerical simulations of fault motion also reveal episodes of stable sliding, tertiary creep preceeding earthquakes, and long-term aseismic creep.

Cohen, S. C.↗

NASA NTRS1980

Stability of large horizontal-axis axisymmetric wind turbines

The stability of large horizontal axis, axi-symmetric, power producing wind turbines was examined. The analytical model used included the dynamic coupling of the rotor, tower and power generating system. The aerodynamic loading was derived from blade element theory. Each rotor blade was permitted tow principal elastic bending degrees of freedom, one degree of freedom in torsion and controlled pitch as a rigid body. The rotor hub was mounted in a rigid nacelle which may yaw freely or in a controlled manner. The tower can bend in two principal directions and may twist. Also, the rotor speed can vary and may induce perturbation reactions within the power generating equipment. Stability was determined by the eigenvalues of a set of linearized constant coefficient differential equations. All results presented are based on a 3 bladed, 300 ft. diameter, 2.5 megawatt wind turbine. Some of the parameters varied were; wind speed, rotor speed structural stiffness and damping, the effective stiffness and damping of the power generating system and the principal bending directions of the rotor blades. Unstable or weakly stable behavior can be caused by aerodynamic forces due to motion of the rotor blades and tower in the plane of rotation or by mechanical coupling between the rotor system and the tower.

Hirschbein, M. S.↗